Without this patch swconfig will only allow setting up a total of 16
VLANs, with VLAN ID range of 0-15.
Tested on ubnt-erx.
Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
Fixing pvs1 bin voltage as found in GPL tarball and Qualcomm SDK.
Also adjusting smb208_s2a/b minimum voltage to reflect lowest value in pvs table.
Current ipq8065 devices in LEDE choose (based on eFuse data) pvs bin n4, that has
correct values in DT, but in future a new device may choose n1 or n6.
Without this change n1 is semi-correct and n6 is not available, because OPP driver
disregards bins with voltage values that regulator cannot supply.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
This adds USB initialization fixes for Danube, Amazon SE and xrx300 and
should fix the clock on at least Danube which hopefully closes FS#351.
The xrx200 usb driver now uses more memory for the dwc2 fifos, this was
increased in the chip compared to ar9.
This is based in part on the vendor documentation and the vendor code
base as a reference.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DMA controller used only local locks, which will not lock the
section against other CPUs, fix this by using spin locks.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we generate images with metadata attached, require it in order
to prevent accidentally flashing the wrong image to a board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for the integrated AC97 sound device on motherboards
with AMD CS5535/CS5536 chipsets.
Tested on Wyse Winterm S30.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
The boot loader of many boards provides a kernel boot argument with a
broken console parameter to the kernel. This will be taken before the
stdout-path defined in device tree and the serial will not work on this
board. Multiple boards are affected by this problem, so revert this
patch for all boards. Later we can remove the boot arguments from the
device tree again, after the individual board was checked to work.
This partly reverts this commit:
commit 4995c64857
Author: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Date: Sun Dec 11 21:55:00 2016 +0100
lantiq: specify console using stdout-path instead of cmdline argument
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To achieve this, device tree compatible string was used as boardname and
the value of it will be checked against supported_devices list.
It should be noted that we do not distinguish between
sun5i-a13-olimex-som and sun5i-a13-olinuxino as they share the same dts
file.
The other thing is that we need to gunzip the generated firmware to do
fwtool check.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Enalbe builtin support for FAT filesystem as we need to mount boot
partition to store sysupgrade.tgz there
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Two things that need to be noted
- There is no partition type id allocated for squashfs yet. In the
case of sunxi, any non-zero value should work and we keep it 83 (the
value for ext4)
- Remaining spare space within the rootfs partition, not the entire
sdcard space will be formated as either f2fs or ext4 and mounted as
overlay to serve the role of rootfs_data.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The new Device/xxx were transformed automatically from old profiles.
Most device names are now taken from basename of the corresponding
kernel device tree file. Device/sun5i-a13-olimex-som is an exception
because it is not explicitly supported in the kernel yet and shares the
same dts file with Device/sun5i-a13-olinuxino
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
To squash error messages at boot time
mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The kernel will detect if the host supports this, so we can just enable
it in the kernel config.
Tested on an APU2 with AES-NI support and a KVM VM on a Xeon E5520 host
without AES-NI support.
Throughput over an IPsec tunnel between these 2 hosts increased from
~63Mbps to ~140Mbps. Ciphers: AES_GCM_16_256/PRF_HMAC_SHA2_512/ECP_521.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
WL500GPv1 profile included ath5k which made it usable only for people
who decided to replace default BCM4318 card with Atheros one. We can't
have profile for every possible configuration. If someone adjusts hw in
such a way he can always install a proper package.
WRTSL54GS profile got extra packages for a specific USB usage. Our
standard profile provides basic USB and we should stick to this. We
can't make everyone happy by including packages for all common USB use
cases and all common filesystems.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The powerpc boot wrapper Makefile is not parallel build safe, causing fixdep
to fail reading dependency files of the addnote, hack-coff and mktree
utilities when concurrently building different image targets.
A typical failure looks like:
Building modules, stage 2.
HOSTCC arch/powerpc/boot/addnote
HOSTCC arch/powerpc/boot/hack-coff
DTC arch/powerpc/boot/taishan.dtb
HOSTCC arch/powerpc/boot/addnote
HOSTCC arch/powerpc/boot/hack-coff
MODPOST 800 modules
fixdep: error opening depfile: arch/powerpc/boot/.hack-coff.d: No such file or directory
scripts/Makefile.host:91: recipe for target 'arch/powerpc/boot/hack-coff' failed
make[5]: *** [arch/powerpc/boot/hack-coff] Error 2
make[5]: *** Waiting for unfinished jobs....
fixdep: error opening depfile: arch/powerpc/boot/.addnote.d: No such file or directory
scripts/Makefile.host:91: recipe for target 'arch/powerpc/boot/addnote' failed
make[5]: *** [arch/powerpc/boot/addnote] Error 2
rm arch/powerpc/boot/taishan.dtb
arch/powerpc/Makefile:263: recipe for target 'cuImage.taishan' failed
make[4]: *** [cuImage.taishan] Error 2
make[4]: *** Waiting for unfinished jobs....
Add a GNU make specific .NOTPARALLEL pseudo rule to enforce sequential building
of the addnote, hack-coff and mktree executables.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This allows more feature complete images. Of course it affect the size,
e.g. enabling b43 bumped rootfs from 1569618 to 2029122 for me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This chip has write protection enabled on power-up, so this flag is
necessary to support write operations.
Signed-off-by: Victor Shyba <victor1984@riseup.net>
This flag was added to 4.9 with upstream commit
76a4707de5e18dc32d9cb4e990686140c5664a15.
Signed-off-by: Victor Shyba <victor1984@riseup.net>
[refresh and adjust platform patches, fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
LS1088A is an ARMv8 implementation combining eight ARM A53 processor
cores. The LS1088ARDB is an evaluatoin platform that supports the
LS1088A family SoCs.
Features summary:
- Eight 64-bit ARM v8 Cortex-A53 CPUs
- Data path acceleration architecture 2.0 (DPAA2)
- Ethernet interfaces
- QUADSPI flash, 3 PCIe, 2 USB, 1 SD, 2 DUARTs etc
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
In case the soft reset in dwc2_core_reset() timeouts, the
hsotg->core_params are freed albeit it is owned by the core. This
results into a kernel panic as shown in FS#351.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the the dt-bindings macros and add the reset button.
Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.
Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit introduced a syntax error in ox820-akitio.dts which is
fixed now:
commit 5cde94d9ab
Author: Daniel Golle <daniel@makrotopia.org>
Date: Sat Sep 24 01:14:53 2016 +0200
oxnas: backport upstream NAND driver
This caused the folowing error message in the build bot:
Error: arch/arm/boot/dts/ox820-akitio.dts:146.3-147.1 syntax error
FATAL ERROR: Unable to parse input tree
scripts/Makefile.lib:293: recipe for target 'arch/arm/boot/dts/ox820-akitio.dtb' failed
make[5]: *** [arch/arm/boot/dts/ox820-akitio.dtb] Error 1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have profile for this device thanks to DEVICE_PACKAGES now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Russell Senior <russell@personaltelco.net>
We don't use this driver since commit 741715331a ("bcm53xx: switch to
m25p80 and drop bcm53xxspiflash").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There was a typo in Makefile that prevented using these profiles.
Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
depending packages have been moved to kernel-config
- kmod-xen-kbddev in 9fde361
- kmod-xen-fs, kmod-xen-evtchn, kmod-xen-netdev in 018807d
this will also fix imagebuilder
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
crypto4xx_probe() is in the __init section and referenced by code form
other sections, which causes a build error. Backport a patch from
mainline kernel to fix this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following commit changed the build templates name but forgot to
update the TARGET_DEVICES variable properly.
commit f9226158be (lantiq: rename EASY98000 to EASY98000NOR)
Signed-off-by: John Crispin <john@phrozen.org>
The generic lzma-loader uses vmlinux.lzma as an input to compress so we
need to provide a lzma compressed version of the initramfs kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The power LED can not be used for indicating the xDSL line state and
the in system (boot) state at the same time in LEDE. As soon as the
xDSL Line goes down, the power LED is switched off.
During xDSL handshake the power led would blink with the same or a
similar pattern as during boot.
Both might confuse users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to a hardware bug of Atheros 8030 phys, the driver need to reset
the phys on link state change.
Use the correct compatible string for the at903x phys connected to
switch port 0 and 1.
Fix the pinmux of the gpio lines connected to the reset pin of the phys
and define the reset-pins to let the driver do the fixups.
Fixes FS#343
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.
Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.
Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.
To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove dt: it is implicitly enabled based on the kernel config
Remove tar.gz and jffs2_nand: Legacy build code has been removed,
NAND devices are only supported with UBI now.
Remove ubifs: deprecated, use squashfs images instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The priv->vlan_id member is of size AR8X16_MAX_VLANS, not AR8X16_MAX_PORTS,
so check for the proper maximum value in order to avoid capping valid VLAN IDs
to 7 (AR8X16_MAX_PORTS - 1).
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Enabled Hyper-V network interface card driver, display adapter driver,
storage driver, keyboard driver, mouse driver and Hyper-V utility and
EFI boot support in the kernel for subtarget x86/64.
Convert the img file to vhd by Ubuntu qemu-img, rather than by the buildroot's
built-in qemu-img.
Tested on Windows Server 2008 r2 and 2012 r2 Gen1 and Gen2 VMs.
Signed-off-by: Tedaz <tedaz99999@hotmail.com>
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.
The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)
The result factory image is flashable from the stock web ui.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The firmware image that is used in TP-Link RE450 (and some more devices from
the RE series) is tplink-safeloader.
In the kernel partition, the kernel is compressed in a regular tp-link
firmware that is just used for booting. Since it is only used for compressing
and booting, only four fields are filled in the header:
Vendor, version, kernel load address and kernel entry point.
mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such
images. It also specifies the hardware id (as it is in the product info
section), so when doing a sysupgrade - the existing code will check for
hardware compatibility.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: add build target to .../image/tp-link.mk]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
mktplinkfw ignores -j in combined mode, the EOF marker is added by
tplink-safeloader.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In the latest version of grub-mkimage, the prefix option is mandatory.
Not supplying it fails with:
```
Prefix not specified (use the -p option).
```
In grub-2.02-beta2 a DEFAULT_DIRECTORY was defined
in `include/grub/osdep/hostfile_unix.h` as:
```
#if defined (__NetBSD__)
/* NetBSD uses /boot for its boot block. */
# define DEFAULT_DIRECTORY "/"GRUB_DIR_NAME
#else
# define DEFAULT_DIRECTORY "/"GRUB_BOOT_DIR_NAME"/"GRUB_DIR_NAME
#endif
```
Where:
* GRUB_BOOT_DIR_NAME == boot
* GRUB_DIR_NAME == grub
This was used if the -p option was omitted.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This patch is part of a series adding support for 0x9200 and 0x9300. The
prior was merged into the upstream kernel while the latter was not due
to lack of testers. Drop the patch as it is untested and most likely
unused.
Signed-off-by: John Crispin <john@phrozen.org>
When running sysupgrade for the first time over the second partition
(that still had stock firmware) the rootfs wasn't flashed as there
wasn't enough space.
This happend because stock also uses UBI, but the volume name wasn't
recognised and wasn't deleted before flashing.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
The si3210 is a SLIC device providing a complete analog telephone
interface and therefore frequently used in soho router.
The si3210 have a native spi interface to be controlled by the CPU
but currently there is no dedicated driver in lede.
Adding a registration for this device in spidev allow to control the
device in user space.
This way of patching is also in line with the rationale of the spidev
driver, see: http://marc.info/?t=148145791900001&r=1&w=2
The si3210 has been also added in the DWR-512 DT to properly describe
the HW.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
While researching for the armvirt target, I looked at the
existing arm platforms. It turns out that the mediatek target
with its sole MT7623N/A chip is sold as a "highly integrated
multimedia network router system-on-chip". To that end, it
lists support for the "NEON multimedia processing engine with
SIMDv2 / VFPv4 ISA support".
<http://topics.mediatek.com/en/products/connectivity/wifi/home-network/wifi-ap/mt7623na/>
So this patch enables the CPU_SUBTYPE to use this information.
This should have the nice side effect that LEDE's phase2 builders
no longer need to built a separate "cortex-a7" target, so this
should free up some resources.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Bump & refresh patches for all 4.4 targets.
Compile & run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Fix the mtd partition layout and enable both radios in the dts
Tested-by Andrius Štikonas <andrius@stikonas.eu>
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
The TL-WR842N v2 has the following switch port layout with swconfig port 0
being connected to eth1:
Power LAN4 LAN3 LAN2 LAN1 WAN USB
(*) | [...] | [...] | [...] | [...] | [...] | [.]
swconfig port: 1 4 3 2 n/a
netdev: eth1 eth1 eth1 eth1 eth0
Adjust the board defaults to match this model specific layout.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The imagetag RSA signature field may not exceed 20 characters, so trim the
Git hash portion from the REVISION variable in order to ensure that the
resulting string fits within this field.
The current revision values may be longer than 20 chars, especially when
building within a dirty tree. In this case, the revision will look like
"r2435+75-b4aa3c8" which, combined with the "LEDE-" prefix, is 21 chars long.
Fixes the following error spotted by the buildbots:
Error: RSA Signature (rsa_signature,r) too long.
make[4]: *** [.../lede-brcm63xx-generic-NEUFBOX6-squashfs-cfe.bin] Error 1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch add the 3G modem DWM-158 to the usb-serial option driver.
The DWM-158 is a pcie 3G modem. It is embedded in the DWR-512 modem
supportet by lede. The patch has been submitted and merged in the upstream
linux-next repository.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
This patch adds supports for the WNR2000v1 board with 4MB flash, and
produces device-specific factory, rootfs, and sysupgrade files for the
WNR2000v1. This board is errorneously claimed as supported on the OpenWRT
wiki as AP81, but AP81 image would not work because of APT81 image
requiring having 8MB of flash, while WNR2000v1 has only 4MB.
The image requires the u-boot bootloader to be modified to fuhry's
bootloader first.
Short specification:
- CPU: Atheros AR9132
- 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps
- 4 MB of Flash
- 32 MB of RAM
- UART header (J1) on board
- 1x button
Factory/Initial flash instructions:
- Set up a TFTP server on your local machine.
- Download the uImage for ar71xx-generic and the rootfs image for
ar71xx-generic-wnr2000 and save in the tftp server root.
- Gain serial access to the router via the UART port (telnetenable over
the network only won't work!).
- Upgrade the u-boot bootloader to fuhry's version by running the
script: http://fuhry.com/b/wnr2000/install-repart.sh
- When the router restarts, interrupt u-boot and gain access to u-boot command line.
- Repartititon the board and flash initial uImage and rootfs as follow.
Commands to type in u-boot:
# tells u-boot that we have a tftp server on 192.168.1.10
setenv serverip 192.168.1.10
# tells u-boot that the router should take the address 192.168.1.1
setenv ipaddr 192.168.1.1
# erase the region from 0x050000-0x3f0000
erase 0xbf050000 +0x3A0000
# loads sqfs.bin on TFTP server, and put it to memory address 0x81000000
tftpboot 0x81000000 sqfs.bin
# it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ
# copy bit by bit 0xZZZZZZ bytes from offset 0x050000
cp.b 0x81000000 0xbf050000 0xZZZZZZ
# same to the uImage.bin, write it right next to sqfs.bin
# again, 0xYYYYYY is the length that tftpboot reports
tftpboot 0x81000000 uImage.bin
cp.b 0x81000000 0xbf2a0000 0xYYYYYY
# We need to tell the kernel what board it is booting into, and where to find the partitions
setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd"
# Tell u-boot where to find the uImage
setenv bootcmd "bootm 0xbf2a0000"
# Tell u-boot to save parameters to the u-boot-env partitions
saveenv
# Reset the board
reset
Tested on:
- WNR2000v1 board.
- Initial flash works.
Known bugs:
- I don't know why factory image doesn't work on initial flash on stock
firmware in u-boot recovery mode while it should.
- Sysupgrade does not yet work, if you do -f it will mess up your
installation (requiring a reinstall of sqfs and uImage).
Signed-off-by: Huan Truong <htruong@tnhh.net>
The xt_id match was used by the firewall3 package to track its own rules but
the approach has been changed to use xt_comment instead now, so we can drop
this nonstandard extension.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
These patches were queued for 4.10. For possible use cases see added:
[PATCH] ubifs: Use dirty_writeback_interval value for wbuf timer
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This also makes the detection more flexible, as it doesn't need to check
for each model explicitly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are many targets using user space scripts to generate firmware but
bcm53xx doesn't need this, so let's disable that kernel option.
This lets us avoid some scary-looking kernel warnings like:
brcmfmac 0001:04:00.0: Falling back to user helper
firmware brcm!brcmfmac43602-pcie.txt: firmware_loading_store: map pages failed
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
/etc/preinit has been the default init-script for a very long time (at
least since Linux 2.6.30 in OpenWrt). Remove the kernel command line
"init" parameter to get rid of duplicate and inconsistent definitions
of this parameter (some boards, like FRITZ3370 for example did not use
it at all, while it's just copy and paste on others).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Use devicetree's /chosen/stdout-path instead of the kernel command line
(embedded in the .dts-files) to specify the serial console. Using the
chosen node is recommended on devicetree based platforms.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.
YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.
Common specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm
SR3200 specification:
- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB
XD3200 specification:
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB
LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.
Flash instruction under vendor firmware, using telnet/SSH:
1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
This attribute is not evaluated any more and the boot loader on these
reference boards does not provide a broken root= or console= parameter.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add an extra function to patch the mac and fixup the checksum
afterwards. Calculate the checksum position automatically. The offset
to the mac address is the same for all checksum protected EEPROMs.
No EEPROM requires a byte swapped mac address. The mac byte swap code
was required due to an bug in the script that is now fixed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The EEPROM data in the flash of the ARV7518PW, ARV8539PW22,
BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning
that for example the ath9k base_eep_header fields "version" (high and
low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are
just 1 byte wide, thus their position is swapped).
The old "ath,eep-endian" property enabled the corresponding swapping
logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is
based on the magic bytes in the EEPROM data which have nothing to do
with the calibration data - thus this logic should not be used
anymore).
Since we have switched to the upstream ath9k devicetree bindings there
is no binding anymore which enables swab16 in ath9k (as this logic is
not recommended anymore as explained above), leading to ath9k
initialization errors:
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
(this shows that the version field is swapped, expected values are VER
0x000E and REV 0x0001)
Swapping the ath9k calibration data when extracting it from the flash
fixes the devices listed above (all other devices do not require
additional swapping, since the position of the fields is already as
expected by ath9k). This allows ath9k to read the version correctly
again, as well as the more important "eepmisc" field (which is used for
determining whether the data inside the EEPROM is Big or Little Endian
which is required to parse the EEPROM contents correctly).
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Rob suggested I should use of_machine_is_compatible insteak of a new
property and updated patch has been sent.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is helpful for Orion-based NAS boxes that have the XOR engine enabled
since it provides faster software RAID.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The harddisk target is for NAS boxes, so set the DEVICE_TYPE accordingly so we
get a sensible default package selection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable support for this machine in the kernel and also produce valid image
files with the correct machine id.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW,
because ar71xx is not converted to device tree yet.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default, forwarding between all ports is allowed on init. This is
problematic in cases where some ports are supposed to be isolated from
each other, most commonly LAN/WAN separation.
REG_ESW_PORT_PCR(port) has a destination mask for a particular port,
controlling what other ports it is allowed to send packets to.
Instead of initializing all to 0xff (all ports), allow each physical
port to send to the CPU port, and the CPU port to send to all other
ports.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.
Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.
Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
sysupgrade command fails due to missing U-Boot environment-processing
binaries on sysupgrade ramdisk. The missing binaries result in the
following output:
Switching to ramdisk...
Performing system upgrade...
ash: /usr/sbin/fw_printenv: not found
ash: fw_setenv: not found
ash: touch: not found
cannot find target partition
Signed-off-by: Vignesh Balasubramaniam <vigneshb.hp@gmail.com>
The name from the Device define will be used in the metadata. Due to
typo/different spelling, this name might not match the one exported in
/lib/mvebu.sh.
Signed-off-by: Mathias Kresin <dev@kresin.me>
use pwr LED in diag.sh
Expose unused pinmux pins as GPIOs
export power LED and buzzer pins
Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr
Signed-off-by: Andrew Yong <me@ndoo.sg>
Imported from https://source.codeaurora.org/quic/qsdk/system/openwrt/commit/?h=korg/linux-3.4.y/release/arugula_bb_cs&id=2be4f8a8b205ae1a37db44839864451ebe893e6e
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Enable flow control of LAN and WAN ports to
get better performance.
Setup pvid as 0 for all ports during initialisation
to avoid confusion during system or switch INIT.
Disable PORT MAC before config MAC to avoid it work abnormal.
This change is for IR-054144, IR-057315.
Change-Id: I345f3dffa59ad3f97150e09692723da12a7b1067
Signed-off-by: Zou Shunxiang <shunxian@codeaurora.org>
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Imported from e1aaf7ec00%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: net: ar8216: address security vulnerabilities in swconfig & ar8216
This patch does the following changes:
*address the security vulnerabilities in both swconfig framework and in
ar8216 driver (many bound check additions, and turned swconfig structure
signed element into unsigned when applicable)
*address a couple of whitespaces and indendation issues
BUG=chrome-os-partner:33096
TEST=none
Change-Id: I94ea78fcce8c1932cc584d1508c6e3b5dfb93ce9
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/236490
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Commit-Queue: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from fd7b89dd46%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: prevent device duplication in ar8xxx_dev_list
If probe is called twice, once for PHY0 and a second time for PHY4,
the same switch device will be added twice to ar8xxx_dev_list, while
supposedly this list should have one element per hardware switch present
in the system.
While no negative impact have been observed, it does happen if a
platform instanciates these two PHYs from device-tree, as an example.
Change-Id: Iddcbdf7d4adacb0af01975b73f8e56b4582e894e
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/234790
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from c3fd96a7b8%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: hold ar8xxx_dev_list_lock during use_count--
It is possible for the remove() callback to run twice in parallel, which
could result into --use_count returning only 1 in both cases and the
rest of the unregistration path to never be reached.
This case has never been observed in practice, but we will fix
preventively to make the code more robust.
BUG=chrome-os-partner:33096
TEST=none
Change-Id: If09abe27fdb2037f514f8674418bafaab3cbdef6
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/232870
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from c05af20272
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: sync mib_work cancellation
ar8xxx_mib_stop() is called from ar8xxx_phy_remove(), so we want to make
sure the work doesn't run after priv is freed / the device ceases to
exist.
BUG=chrome-os-partner:33096
TEST=none
Change-Id: Iafb44ce93a87433adc4576e5fea5fda58d1f43a9
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/232827
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
RPM clock controller driver had made its way upstream and previous
approach of directly redoing a driver to support ipq806x is a no go anymore.
Thus reverting mentioned patches to upstream state and renaming
in correct patch numbering accordance.
To make the driver work on ipq806x boards we introduce a custom patch.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The SDK Makefile still trys to copy the docs folder which was removed
with 882f4d2d63. This causes an SDK build
error.
All other removals are just cleanup.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Refresh patches on all 4.4 supported platforms.
077-0005-bgmac-stop-clearing-DMA-receive-control-register-rig.patch
removed as now upstream.
Compile & run tested: ar71xx - Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ifxhcd never had roothub support but since kernel 3.x it was expected
that a roothub always exists.
The patched fixed a null pointer deref in the usb subsystem because of
the missing roothub.
Since ifxhcd is gone, this whole patch isn't required any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This way the on nand bad block table is preserved and used. Add support
for nand OOB ECC checksums as well. It should fix all reported ubi
errors, which were all related to bad nand blocks and a purged on nand
bad block table.
The existing ubi partition will be reused, which eliminates the need
to touch the caldata during initial install. The BT u-boot has support
for loading a kernel from an ubi volume. It isn't necessary any longer
to replace the BT u-boot with a custom compiled one to use LEDE.
It is required to restore the BT Firmware and install LEDE from scratch
to switch to the new partition layout.
An image for restoring the BT firmware and installing LEDE is provided
at https://github.com/mkresin/lede/releases.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport upstream commit a61ae81a1907af1987ad4c77300508327bc48b23.
The actually purpose of the patch was to do some cleanup. As a side
effect of this cleanup, the device node is now passed to nand_dt_init.
This allows to use the common nand device tree properties
- nand-bus-width
- nand-on-flash-bbt
- nand-ecc-mode
- nand-ecc-step-size
- nand-ecc-strength
for the plat_nand driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the addition of the bindings to the ath9k driver, this code
isn't used any longer. The fixup is now done by the owloader.
Rename the ath_eep.c file to ath5k_eep.c to indicate that this files
includes ath5k related code only.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.
The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove all comments in ubnt_xm_board_detect(), as it's not possible to add
comments to specific lines of the case construct anyways.
Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
