All kernel config files are refreshed by
`make kernel_oldconfig CONFIG_TARGET={subtarget_target,subtarget}`
"CONFIG_SQUASHFS_DECOMP_SINGLE=y" is manually selected as all ath79
SoCs are single core processors.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The upcoming 6.6 kernel will introduce a new upstream generic
"gpio-latch" driver. It will conflict with the downstream MikroTik
GPIO latch driver. Let's rename it to avoid any potential issues.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x0 | |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset
MAC Table
Label xx:xx:xx:xx:xx:EB
LAN xx:xx:xx:xx:xx:EB
2.4Ghz xx:xx:xx:xx:xx:EC
5Ghz xx:xx:xx:xx:xx:ED
WAN xx:xx:xx:xx:xx:EE
Flash instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image
D-Link Recovery GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the recovery mode GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the recovery page for the device at http://192.168.0.1/
6. Use the provided emergency web GUI to upload the recovery.bin to the device
Firefox on Windows in a Private Window (incognito) works me
Internet Explorer mode in Microsoft Edge works for others
seems to not work in Linux or virtual machine on Linux for most
some see success using 'curl -v -i -F "firmware=@file.bin" 192.168.0.1'
Thanks to @frkca and @rodneyrod for testing and pushing for its creation
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Setting the LED name and abandoning the label and using the
function/color syntax for some TP-Link Archer series routers:
Archer C2 v1, Archer C20 v1, Archer C20i and Archer C50 v1
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Abandoning the label and using the function/color syntax for some dlink
dir series routers: dir-1960-a1, dir-2660-a1, dir-2640-a1, dir-3040-a1
and dir-3060-a1
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Rename from mt7621_dlink_dir-xx60-a1.dtsi to mt7621_dlink_dir_nand_128m.dtsi
and associated group name when creating the mt7621.mk image
Co-authored-by: Alan Luck <luckyhome2008@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Continuation of commit 8b66f1a. Set the switch address on the MDIO bus to 31.
This is required for all boards currently working with the mt7530 DSA driver.
Fixes: #15419
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Backport patch merged upstream for rgmii-id support in stmmac-ipq806x.
This is needed for some device that directly connets PHY to the gmac
port and require rgmii-id phy-modes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
WPJ419 is still manually defining SPI node, so lets
convert it to use the existing upstream labels for SPI node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining pinctrl node, so lets
convert it to use the existing upstream labels for pinctrl node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining PCIe node, so lets
convert it to use the existing upstream labels for PCIe node and while we
are here use the -gpios suffix instead.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some boards are still defining MDIO nodes under soc instead of using the
existing upstream labels to reference them so convert them.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some boards are still defininig I2C nodes under soc instead of using the
existing upstream labels to reference them so convert them.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some boards are still defininig UART nodes under soc instead of using the
existing upstream labels to reference them so convert them.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
This device does not have NAND enabled at all and NAND is the only consumer
of QPIC BAM DMA, so drop the node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining dma nodes(And even some labels), so lets
convert it to use the existing upstream labels for DMA nodes.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, a lot of boards are still not using the existing label to
reference the crypto node, so lets rectify this.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, a lot of boards are still not using the existing label to
reference the prng node, so lets rectify this.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, a lot of boards are still not using the existing label to
reference the watchdog node, so lets rectify this.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
The way to register the switch MDIO bus and PHYs on the bus in upstream
Linux is more strict and requires each PHY to explicitely state the
interrupt instead of assuming it in case the 'interrupts' property in DT
is missing.
Add missing interrupts for the PHYs of the build-in 4x1GE switch of the
MT7988 SoC.
Fixes: 4354b34f6f ("generic: 6.6: sync mt7530 DSA driver with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
To fix issue #15304
Correct br-lan ports 1-4 so that phy-handle matches reg nr not port label.
Fixes: eb13076e77 ("mediatek: fix DTS defining mt7530 switch phys but not referencing them")
Signed-off-by: Magnus Lindström <magnus1089@hotmail.com>
The Gemini works fine with kernel v6.6.
As per the example for ipq806x, drop support for anything
older than v6.6, there is no point in supporting it,
and the new DTS SoC directory just makes it hard to
maintain.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Backport driver from upcoming Linux 6.10 and put a pending fix on top
to make sure the netdev trigger offloading behaves as expected.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Support for Renesas Arm families was added in commit 1ff4f4df23
("armsr: armv8: enable CONFIG_ARCH_RENESAS"), but this did not
enable the console/tty hardware for these SoCs, which is derived
from the SuperH family (CONFIG_SERIAL_SH_SCI).
Link: https://github.com/openwrt/openwrt/issues/15284
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Due to a change in kernel 6.2, the GPIO numbers on certain
architectures (including arm64) have changed. This script
will update any defined GPIO switches to the new numbering.
See https://lists.openwrt.org/pipermail/openwrt-devel/2024-March/042448.html
for more information.
In the future, the GPIO switch mechanism will likely be
replaced with something using libgpiod.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
A change in kernel 6.2[1] caused the base numbers of GPIOs to
change significantly on some architectures like aarch64.
We have to number our GPIOs accordingly.
Ideally the board.d scripts should look through sysfs
to find the basenum (like cat "/sys/devices/platform/soc/2000000.i2c/
i2c-0/0-0076/gpio/gpiochip640/base"), but the problem is
that this occurs before modules are loaded, meaning I2C and other
runtime devices may be missing.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] https://lore.kernel.org/lkml/cover.1662116601.git.christophe.leroy@csgroup.eu/T/
Introduce new configuration options prompted by 6.6 (relative to 6.1).
The kernel arm64 defconfig is used as guide for 'core' options, while
video/camera/other media drivers are turned off by default.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
LAN Leds on Meraki MR52 are wrong and needs to be swapped to actually
reflect real ports (lan1<->lan2).
Fixes: #15388
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15410
[ wrap commit to 80 columns and improve commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
According to the Realtek SDK code, the RTL8214FC, RTL8218B and RTL8218FB
all have the same chip ID 0x6276. Let's add a constant for it, as we're
using it in more than one location.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Respect the phy-is-integrated property on ethernet-phy nodes.
There are RTL8393M switches where the PHYs at address 48 and 49 are
provided by an external RTL8214FC. Hardcoding them to use the internal
SerDes makes it impossible to use the ports connected to such an
external PHY. Respect the phy-is-integrated property on ethernet-phy
nodes as a first step to support such ports.
The potential impact for this should be limited to RTL8393 based
switches, and looking at the commit messages and device tree files of
the supported switches based on this SoC, the SFP and/or combo ports are
either not working (D-Link DGS-1210-52, Netgear GS750E, TP-Link
SG2452P/T1600G-52PS), use PHYs at a different address (Panasonic
SwitchM48EG PN28480K), or already have the phy-is-integrated property
set on the PHYs at address 48 and 49.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
There was a typo in commit 5709254690 ("mediatek: bpi-r4: store random
MAC addresses for the BPi-R4"). Let's fix it and also add support for
the bpi-r4-poe variant.
Fixes: 5709254690 ("mediatek: bpi-r4: store random MAC addresses for the BPi-R4")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
In commit cd4de3251c ("mediatek: wait for fitblk rootfs"), the linux
6.6 files and patches has been forgotton to be fixed.
Fixes: cd4de3251c ("mediatek: wait for fitblk rootfs")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
In commit cd4de3251c ("mediatek: wait for fitblk rootfs"), the linux
6.6 files and patches has been forgotton to be fixed.
Fixes: cd4de3251c ("mediatek: wait for fitblk rootfs")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
