Enables use of NVMe storage devices with appropriate adapter in miniPCIe slots (including for boot)
in Turris 1.x routers and possibly NXP P2020RDB boards
(these are the only currently supported p2020 devices according to docs[^1]).
Proper detection, mountability and readability was proved to be working
on Turris 1.1, OpenWrt 21.02 with similar configuration.
Increases gzip compressed kernel size by approximately 37 KiB (from 3 703 KiB to 3 740 KiB).
Should boot from those devices be possible the driver needs to be built in.
Inclusion as a module would prevent this functionality.
CONFIG_BLK_DEV_NVME=y
Includes NVMe driver in the kernel.[^2]
CONFIG_NVME_CORE=y
Selected by CONFIG_BLK_DEV_NVME.[^3] Not necessarily needed to be enabled explicitly,
but included to match the form of similar functionality implementations
for mvebu, x86_64 and rockchip_armv8 targets.
CONFIG_NVME_MULTIPATH disabled explicitly to prevent using more space than necessary.
[^1]: https://openwrt.org/docs/techref/targets/mpc85xx
[^2]: https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[^3]: https://cateee.net/lkddb/web-lkddb/NVME_CORE.html
Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
Bumping max frame size has significantly affected network performance
and memory usage. It was done by upstream commit that first appeared in
the 5.7 release.
Allocating 512 (BGMAC_RX_RING_SLOTS) buffers, 10 k each, is clearly a
bad idea on 32 MiB devices. This commit fixes support for Linksys E1000
V2.1 which gives up after allocating ~346 such buffers running 5.15
kernel.
Ref: 230c9da963 ("bcm53xx: revert bgmac back to the old limited max frame size")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Most of the time when booting kernel prints a warning from
mm/page_alloc.c when pstore/ramoops is being initialized and ramoops is
not functional.
Fix this by moving ramopps node into reserved-memory block as described
in kernel documentation.
Fixes: 2964e5024c ("ipq806x: kernel ramoops storage for C2600/AD7200")
Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
After switching to DSA, the LAN ports in Cell C RTL30VW have swapped numbers. Assigning the right numbers.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
When fstools is unable to parse our root=<...> arg correctly, it can
fall back to scanning all block devices for a 'rootfs_data' partition.
This fallback was deemed wrong (or at least, a breaking/incompatible
change) for some targets, so we're forced to opt back into it with
fstools_partname_fallback_scan=1.
Without this, OnHub devices will use a rootfs-appended loop device for
rootfs_data instead of the intended 3rd partition.
While I'm at it, just move all the boot args into the 'cros-vboot'
build rule, instead of using the custom bootargs-append. All cros-vboot
subtargets here are using the same rootwait (to support both eMMC and
USB boot) and root/partition args.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[ drop unrelated comments in commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The phy-mode property must be defined on the MAC instead of the PHY. Define
phy-mode under gmac1 which the external phy is connected to.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Match interface numbers with printed numbers on device enclosure and
assign first port as WAN interface.
Notes
Serial console is available through RJ-45 port with Cisco pinout
baud: 19200, parity: none, flow control: none
The device is setup with UEFI. To enter setup hold DEL or ESC key on
boot. Default UEFI Administrator password is: bcndk1
For users using graphics IC it's advisable to disable display with:
i915.disable_display=1
appending to kernel command line inside bootloader, to save about
0.5-0.6W energy on idle.
For users not using graphics IC, disable it in UEFI, this will save about
1.5W energy on idle.
Pins marked CN19 are ATX power On/Off button.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
These devices have a partition table stored in flash, which compensates
for any pre-existing bad blocks by enlarging the respective partition.
This means that the current static partition table is only correct for
devices without any bad blocks.
Typical results of this mismatch are degraded wireless performance and
wrong MAC addresses, when the factory partition is shifted due to a bad
block somewhere before it. If there is a bad block already before the
ubi partition, then OpenWrt may not run at all because the kernel can't
find the rootfs.
Use the on-flash partition table to fix these issues. Replace the two
reserved partitions by the full partition list, as the driver does not
allow merging them.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Kconfig docs say:
> The default value deliberately defaults to 'n' in order to avoid
> bloating the build.
Apply this rule everywhere, to avoid more cloning of bad examples
Signed-off-by: Tony Butler <spudz76@gmail.com>
This commit adds support for the V4 hardware revision of the Deco M4R.
V4 is a complete overhaul of the hardware compared to V1 and V2,
and is much more similar to the Archer C6 V3 and C6U V1.
Specifications:
SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads)
RAM: Kingston D1216ECMDXGJD (256 MB)
Wireless 2.4 GHz: MediaTek MT7603EN
Wireless 5 GHz: MediaTek MT7613BEN
Flash: 16 MB SPI NOR
Installation:
Flash the *-factory.bin image in the U-Boot recovery webserver.
You can trigger this webserver by holding the reset button until the LED
flashes yellow, or by hooking up to serial pads on the board (clearly
labeled GND, RX and TX) and pressing `x` early in boot.
Once the factory image has been flashed, you can use the regular upgrade
procedure with sysupgrade images for subsequent flashes.
Signed-off-by: Mark Ceeha <hi@shiz.me>
Tested-by: Mark Ceeha <hi@shiz.me>
This makes the patches and the kernel configuration apply on top of
kernel 5.15.
The following patch was removed because the old IDE subsystem was
removed from upstream kernel:
target/linux/bcm47xx/patches-5.15/610-pci_ide_fix.patch
This was tested successfully on a ASUS WL-500g Premium V1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
shellcheck warns against it with SC2086. It also hides a bug that
shellcheck marks with SC2015. Fixed those with explicit if/else.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Instead of using the shell's evaluation, use grep's -q parameter.
Found with shellcheck's SC2143.
Also replaced a head call with grep's -m.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Enable the CPU frequency scaling statistics in kernel config.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Use generic earlycon on Linux Kernel instead of initialization in platform
setup.
And also, drop bootargs with console= parameter from I-O DATA BSH-G24MB. It
uses 115200bps as baud-rate, the same as default in rtl838x.dtsi.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
ath25 seems to be a target with low number of users according to download
statistics, most of which are for older releases anyway.
Users that we managed to find are currently building images downstream as
due to low amount of RAM (32MB) default config will not work.
Target also suffers from inability for the 5.15 kernel bump to be tested
which is a requirment for the next release.
So, for those reasons, lets mark it as source-only so that Buildbots dont
use the resources for building the images for this target anymore.
Signed-off-by: Robert Marko <robimarko@gmail.com>
On the realtek target, the subtarget makefiles include a KERNEL_PATCHVER
setting, shadowing KERNEL_PATCHVER from target/linux/realtek/Makefile.
This makes the realtek target an exception in this regard, and makes
switching kernel version a bit bothersome. Remove the overrides so all
subtargets use the same kernel version.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Device is the same as Xiaomi Mi Router 4A Gigabit, except of:
- 5G WiFi is MT7663
- addresses of leds, wifi and eth ports are slightly changed
Specs:
SoC: MT7621
CPU: 2 x 880 MHz
ROM: 16 MB
RAM: 128 MB
WLAN: MT7603, MT7663
MAC addresses:
WAN **** factory 0xe006 (label)
LAN *:f7 factory 0xe000
2.4 GHz *:f8 factory 0x0000+0x4 (mtd-eeprom+0x4)
5 GHz *:f9 factory 0x8000+0x4 (mtd-eeprom+0x4)
Installation:
Factory firmware is based on a custom OpenWrt 17.x.
Installation is the same as for Xiaomi Mi Router 4A Gigabit.
Probably the easiest way to install is to use the script from
this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155
In a more advanced case, you can do everything yourself:
- gain access to the device through one of the exploits described
in the link above
- upload sysupgrade image to /tmp
- overwrite stock firmware:
# mtd -e OS1 -r write /tmp/sysupgrade.bin OS1
Recovery:
Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit.
Possible options can be found here:
https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition
One of the ways is to use another router with OpenWrt:
- connect both routers by their LAN ports
- download stock firmware from [1]
- place it inside /tmp/test.bin on the main router
- configure PXE/TFTP on the main router
- power off 4Av2, hold Reset button, power on
- as soon as image download via TFTP starts, Reset can be released
- blinking blue wan LED will indicate the end of the flashing process,
now router can be rebooted
[1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin
Signed-off-by: Dmitry Sokolov <e323w@proton.me>
- drop unneeded default-state for led_power
- concat firmware partitions to extend available free space
- increase spi flash frequency to 32 Mhz (value from stock firmware bootlog)
- drop broken-flash-reset because of onboard flash chip W25Q256FV has reset support
- add compatible for pcie wifi according to kernel documetation
- switch to wan mac address with offset 0x28 in rf-eeprom
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
