some config `depends on` lines contained outdated kernel version checks
that can no longer happen and had become non-operational; clean them up
cosmetic change with no functional effect
Signed-off-by: Tony Butler <spudz76@gmail.com>
This adds options to build all boards of a selected target and an
additional option to build the testing kernel instead of the normal
kernel. This can be used by other trigger work flows.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds an option to build with internal toolchain. This can be used
to build targets which are currently not build by the OpenWrt build bots
and which needs their own toolchain build for every build.
Building the toolchain takes about 30 minutes compared to using the
external toolchain which takes some seconds.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Extract the building of OpenWrt into an own workflow which is then
triggered by the kernel.yml and packages.yml workflow with different
inputs. This allows us to share much of the code of the workflow.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In light of https://github.com/openwrt/openwrt/issues/11077, switch mvebu
to 5.15 which has been the testing kernel on this target since April - over
half a year.
Run-tested on the following subtargets:
* cortexa9 (Turris Omnia - 03f41b1eb2)
* cortexa72 (MikroTik RB5009UG+S+IN)
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com> [GL-MV1000]
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
should be add/delete or abbreviated add/del
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The code in dsa.c:rtl83xx_port_enable() was trying to set
vlan_port_tag_sts_ctrl while dealing with differences between SoCs.
However, not only that register has a different address, the register
structure and even the 2-bit value semantic changes for each SoC.
The vlan_port_tag_sts_ctrl field was dropped and converted into a
vlan_port_keep_incoming_tag_set() function that abstracts the different
between SoCs. The macro referencing that register migrated to the SoC
specific c file as it will be privately used by each file.
All magic numbers were converted into macros using BITMASK and
FIELD_PREP.
The vlan_port_tag_sts_ctrl debugfs was dropped for now as it is already
broken for rtl93xx. The best place for SoC specific code might be in each
respective c file and not in if/else clauses.
The final result is:
rtl838x: set ITAG_STS=TAGGED, same as before
rtl839x: set ITAG_STS=TAGGED instead of IGR_P_ITAG_KEEP=0x1, fixing
forwarding of tagged packets
rtl930x: set EGR_ITAG_STS=TAGGED instead of IGR_P_ITAG=0x1, possibly
fixing forwarding of tagged packets
rtl931x: set EGR_ITAG_STS=TAGGED instead of OTPID_KEEP=0x1, possibly
fixing forwarding of tagged packets
Without (EGR_)ITAG_STS=TAGGED, at least for rtl839x, forwarded packets
will drop the vlan tag while packets from the CPU will still have the
correct tag.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The rtl930x speed status registers require 4 bits to indicate the speed
status. As such, we want to divide by 8. To make things consistent with
the rest of this code, use a bitshift however.
This bug probably won't affect many users yet, as there aren't many
rtl930x switches in the wild yet with more then 10 ports, and thus a
low-impact bugfix.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[also fix port field extraction]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The label used for stable branch is in the form of
release/[0-9][0-9].[0-9][0-9]
Currently we apply the name of the target branch as the label, fix this
and correctly use the current label.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support to tag pr targeting stable branch matching the simple regex
of openwrt-[0-9][0-9].[0-9][0-9]. The tag that will be added will match
the pr target branch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Raise CONFIG_LMB_MAX_REGIONS to 64 as there are going to be more than
8 (the default value) reserved regions to allow supporting offloading
Wireless-to-Ethernet traffic on MT7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add new UCI list 'addn_mount' allowing the expose additional filesystem
paths to the jailed dnsmasq process. This is useful e.g. in case of
manually configured includes to the configuration file or symlinks
pointing outside of the exposed paths as used by e.g. the safe-search
package in the packages feed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP
with a miniPCIe slot for a LTE modem.
The wAP R AC is similar to the wAP AC but with the miniPCIe slot.
The wAP R AC requires installing a LTE modem.
The wAP LTE and wAP LTE6 comes with a LTE modem installed.
See https://mikrotik.com/product/wap_r_ac for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- CPU: 4x ARM Cortex A7
- RAM: 128MB
- Storage: 16MB NOR flash
- Wireless:
- Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna
- Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports
one with 802.3af/at PoE in
- 1x Mini PCI-E port (USB2)
Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Swconfig isn't used by this target and can be disabled for
this reason. Airoha doesn't even have an Ethernet driver.
In the future, this target should get a DSA driver.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
In 8274451cb86 kmod-ppfe was changed to built-in because CONFIG_FSL_PPFE
was binary. In 5.10 and 5.15 kernel, PPFE driver can be build as module.
This patch switch kmod-ppfe from build-in to loadable module.
Loadable module helps to avoid hazard: driver is looking for firmware
file before mount root.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Let's test layerscape with 5.15 kernel.
Run tested: LS1012A-FRDM, LS1046A-RDB (nor and sd-boot images),
LS1021A-IOT (By @ArtelMike with u-boot fix)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
At this moment LS1012A-FRDM have uncompressed initramfs image.
Error was caused, because gzip extract area overlap image.
Let's change loadaddr and enable gzip initramfs images again.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
For some reason LS1012A and LS1046A devboards don't work well with
Spansion SPI NOR flash. It cause read and write errors like:
[ 27.285887] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x025ae000
[ 27.468922] jffs2: Newly-erased block contained word 0x0 at offset 0x02573000
[ 27.502615] jffs2: Newly-erased block contained word 0xe723f41e5823f110 at offset 0x02572000
[ 27.541550] jffs2: Newly-erased block contained word 0x1a7d266ee6 at offset 0x02571000
[ 27.577195] jffs2: Newly-erased block contained word 0x5d000bae8d52fec6 at offset 0x02570000
[ 27.611800] jffs2: Newly-erased block contained word 0x63515aee63515a4b at offset 0x0256f000
[ 27.651749] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0256e000
[ 27.825593] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0252e000
NXP have found workarround and applied in their vendor kernel version.
They force 1x tx and 1x rx lines in qspi. That method fix issues.
This patch ports patches from NXP LSDK tree.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
- Bring back factory.bin image which was missing after porting device to ath79 target
- Use default sysupgrade.bin image recipe
- Adjust max image size according to new firmware partition size after
"ath79: expand rootfs for DIR-825-B1 with unused space (aca8bb5)" changes
- Remove support of upgrading from version 19.07, because partition size changes mentioned above
Signed-off-by: Will Moss <willormos@gmail.com>
FCC ID: A8J-EAP1750H
Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9558 SOC
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16FG
- UART at J10 populated
- 4 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)
**MAC addresses:**
MAC addresses are labeled as ETH, 2.4G, and 5GHz
Only one Vendor MAC address in flash
eth0 ETH *:fb art 0x0
phy1 2.4G *:fc ---
phy0 5GHz *:fd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
NOTE: TFTP is not reliable due to bugged bootloader
set MTU to 600 and try many times
if your TFTP server supports setting block size
higher block size is better.
**Format of OEM firmware image:**
The OEM software of EAP1750H is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
openwrt-ar71xx-generic-eap1750h-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Driver for and pci wlan card now pull the calibration data from the nvmem
subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.
Test passed on my tplink tl-wr2543nd.
Signed-off-by: Edward Chow <equu@openmail.cc>
The redundant character '0x0a' after the 192 bytes '0x00' padding broke
the factory image. We need to remove it to make things work again.
Fixes: e6769d11f3 scripts: fix missing character '0' issue in linksys image
Tested-by: Tony Butler <spudz76@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Manually rebased: ath79/patches-5.10/910-unaligned_access_hacks.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Instead of manually overriding every cmake package that uses iconv or
gettext's paths, add the prefix in here so that at least FindIconv.cmake
works. Fixes compilation with BUILD_NLS.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
It was tested that cache scaling currently cause instability problem.
This is probably caused by a latent misconfiguration that cause the L2
cache to be sourced from the wrong source and runs at an unstable freq
compared to the original QSDK fw.
To improve stability while the problem is bisected, disable the devfreq
drivers with minimal perf penality.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break
Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use persistent MAC address for the built-in wireless interfaces of the
BPi-R64 and BPi-R3 development boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The type of those images is already distinguishable by the '.itb'
extension, there is no need for an additional '-fit' string in the
filenames. Remove it to behave more like other targets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only on the ipq40xx subtarget different filenames were used for NAND-
based devices. This is unneeded, confusing and breaks downstream tools
such as luci-app-attendedsysupgrade and auc.
Remove the 'nand-' string from image filenames to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>