This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d
Improvements:
- Remove software watchdog as hardware watchdog now working as per
commit 3fbf3ab44f for all mt7621
devices.
- Reset button polarity corrected - length of press determines reboot
(short press) vs. reset to defaults (long press) behaviour.
- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
link and blink on activity. Green LEDs driven directly by switch
indicating any link speed and tx activity.
- USB port power on/off GPIO exposed as 'usbpower'
- Add access to uboot environment settings for checking/setting uboot
boot order preference from user space.
Changes:
- Front LED indicator is physically made of independent Yellow/Amber,
Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
indicator, hence the colour behaviour is similar to an RGB LED. RGB
LEDs are not supported at this time because they produce colour results
that do not then match colour labels, e.g. enabling 'mir3g:red' and
'mir3g:blue' would result in a purple indicator and we have no such
label for purple.
The yellow, red & blue LEDs have been split out as individual yellow,
red & blue status LEDs, with yellow being the default status LED as
before and with red's WAN and blue's USB default associations removed.
- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
layout. eth0.1 is LAN, eth0.2 is WAN
- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
leakage between kernel switch init and uci swconfig
uboot behaviour & system 'recovery'
uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed
last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2. last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok. If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.
NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.
Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.
Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.
Installation - from stock.
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot
Recovery - to stock.
Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)
Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'
All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot
The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted. Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Fixes the following build issue: "undefined reference to `EVP_MD_CTX_create'"
From: Jelle van der Waa <jelle@vdwaa.nl>
The rsa_st struct has been made opaque in 1.1.x, add forward compatible
code to access the n, e, d members of rsa_struct.
EVP_MD_CTX_cleanup has been removed in 1.1.x and EVP_MD_CTX_reset should be
called to reinitialise an already created structure.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[replaced u-boot patch with original version from u-boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The arm-trusted-firmware-sunxi package is only used by the Allwinner
A64, so only make it selectable for its subtarget sunxi/cortexa53.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
at91bootstrap is a second-level bootloader for Microchip(Atmel AT91) SoCs.
It provides a set of algorithms to manage the hardware initialization and
to download the main application or a third-level bootloader(i.e. uboot)
from specified boot media to main memory and execute it.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D4 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D2 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D3 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
IPQ806x AP148 and DB149 boards didn't have the UCI ubootenv
section initialized, so the usage of fw_printenv required manual
configuration. With this change, the "fw_printenv" and "fw_setenv"
command will automatically work on NOR and NAND based platforms.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Backing up the current firmware from U-Boot over serial can take hours.
Booting a working Linux image for backup purposes is not always an option.
Using the tftpput command in U-Boot is the fastest and easiest way.
tftpput will upload the contents of a memory region to the TFTP server.
The IP address of the server is stored in the serverip variable.
Usage:
tftpput <memaddr> <length> <filename>
Example for a complete flash backup of an o2 Box 6431 (VGV7510KW22):
VGV7510KW22 # tftpput 0xB0000000 0x1000000 o2boxbackup.bin
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
split kexec-tools into two packages, kexec and kdump.
* kexec to simply execute a new kernel
* kdump is for loading and collecting debris of a crashed kernel with
support for kdump forensics.
In order to properly support booting into a crashkernel, an init script
as well as UCI configuration has been added.
As modifying the kernel cmdline is required for this to work in x86
platforms use an uci-defaults script to modify /boot/grub/grub.cfg.
To test collecting crash information, use the 'c' sysrq-trigger, ie.
echo c > /proc/sysrq-trigger
This should result in the crash kernel being executed and (depending
on the configution) dmesg and/or vmcore getting saved.
To check if the crash kernel was loaded properly, use the 'status'
command of the kdump init script.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.
The device is based on Qualcomm/Atheros AR9341 v1.
Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button
Flash instructions:
You have three options:
- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.
- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.
- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:
*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
stat -- Status
sys -- System
wless2 -- 2.4G-Wireless
mgmt -- Management
tree -- Tree
help -- Help
reboot -- Reboot
ens202ext>mgmt
Management
---========= Commands Help =========---
admin -- Administration
mvlan -- Management VLAN settings
snmp -- SNMP settings
backup -- Backup/Restore settings
autorb -- Auto reboot settings
fwgrade -- Firmware upgrade
time -- Time settings
wifisch -- Wifi schedule
log -- Log
diag -- Diagnostics
disc -- Device Discovery
logout -- Logout
help -- Help
exit -- Exit
ens202ext/mgmt>fwgrade
Management --> Firmware upgrade
---========= Commands Help =========---
fwup -- Firmware upgrade
help -- Help
exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin
Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
Add a patchfile that implements distro-boot and is meant to go upstream
Also make the other patches git-am'able for easier maintenance.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Even it's unknown if it's booting with thumb, because the lack of hardware.
Enable it for now, so the build succeed, because without thumb it can not fit
into spl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The beagleboard doesn't boot with Thumb enabled, but without Thumb the
SPL (first stage bootloader) is too big to fit into SRAM.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Use fixed led names and add each board variant instead of manipulating
the board name.
It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Couple of important upstream patches (slated for 2.0.15) that
are necessary for kexec to run on MUSL and on x86 hardware.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
With upstream changes, the last update to U-Boot 2017.03
broke the nsa310 and nsa325 targets. Also fix some redefines.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
Backport kernel patches for LS1043A Rev1.1 support from upstream,
patchwork, and SDK. And update to latest u-boot to support LS1043A
Rev1.1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This is needed for the definition of $(LINUX_DIR). This is used in
u-boot.mk to change the device-tree compiler to the dtc used by
linux.
Without this, the build will use the system dtc. This results in a
build failure when a dtc does not exist outside the buildroot.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Specifying USE_PRIVATE_LIBGCC is no longer needed, as it is the
default.
Patch 001 is removed, since it was already merged upstream. Patches
100 and 101 are removed because they do not appear to be needed
anymore, and they do not conform with the sign-off and commit message
procedures.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Because they were hidden, there was no way to disable the uboot
targets in menuconfig, so they had to be built every time. The omap
target is the only one to hide uboot packages. To be consistent with
the other targets, and have more control over the build, un-hide the
u-boot packages.
Note that the default behavior remains unchanged, as uboot will be
built unless explicitly disabled.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
fixes issue "nsa 310b u-boot can initialize usb but cannot
use usb storage so it cannot load files from usb"
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Goflexhome/net use uImage, and to boot an uImage the u-boot
must use bootm command, not bootz.
Fixes the "i cannot boot LEDE with this u-boot" issue that I
found out myself with my goflexnet.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
all patches for CONFIG_SYS_GENERIC_BOARD are obsolete for
uboot 2016 sources.
Run-tested with the uboot of goflexnet, also the md5sum of
all other uboots is the same with or without these patches.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
All SPL variants are lzo compressed. The lzop binary is used for
compression but is not available in tools.
Additionally at least the NAND SPL support is broken and doesn't create
working bootloaders.
The fb3370 SPI NOR SPL enabled u-boot isn't required for LEDE since the
LEDE images are targeting the pre-installed EVA bootloader.
Mark these u-boot variants as well as the SPL variants for the
reference boards as broken till the lzma issues are fixed upstream and
we can use lzma instead of lzo compression.
Signed-off-by: Mathias Kresin <dev@kresin.me>
accessing the u-boot's envs on this device is required to read the mac address.
These are the envs of the new u-boot, not of the stock one.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Instead of referencing u-boot packages from device profiles and having a
-all metapackage, make the u-boot packages hidden (they don't install to
bin/ anyway), and name the files in KERNEL_BUILD_DIR appropriately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
this commit allows to make a standalone u-boot for nsa310b.
While both first-stage and second-stage u-boot work fine if
installed to flash or loaded with kwboot,
I could not get stock u-boot nor bodhi's u-boot to chainload
any second stage u-boot (I also tried with dockstar's uboot
that works fine on this device if loaded with kwboot).
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
While at it, the following changes are introduced
- Rewrite the Makefile for better readability
- Make parallel builds possible
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
