When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti Rocket M Titanium, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
While at that, split RSSI into ~equal intervals for 6 LEDs,
and remove coefficients needed for PWM LEDs, as this board does not
support PWM LEDs.
Finally, for complete support, enable 'rssileds' package in per-device
rootfs, so the indicator works out of box.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 83708f233d)
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 9b02d32e34)
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.
Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).
With this patch, we provide proper support for this device in ar71xx.
Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254
Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c79b796280)
[added CPE510V2 entry to tplink-safeloader.c]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update WLAN LED colour identifier for both interfaces on Archer C7
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit 65762cdd22)
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which are using
ar8xxx switch LEDs trigger, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Network for the Archer C25 v1 is set up without switch for no
obvious reason. The LED setup is even done switch-based.
This patch changes network setup so a switch is created.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device shares the network config with v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.
Based on: https://github.com/openwrt/openwrt/pull/1726
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Looks identical to the v2.
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I've missed leading whitespace issues in the original patch, so fixing
it in this commit. Thanks to pepe2k for letting me know.
Fixes: d260813d ("ar71xx: ens202ext: Fix VLAN switch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The target ENS202EXT was just recently added right before the stable
release of Openwrt 18.
It flashes fine, but the physical switch is almost impossible to use
until you have a VLAN set up. Tested on two devices.
The actual problem is that eth0 represents nothing for whatever reason.
In other words, both WAN and LAN are running from eth1. There may be an
underlying problem in the build, but for now, I assume that this is
correct and that a VLAN switch is an appropriate fix.
Also, it's virtually impossible to get the switch running right through
LuCI. It is one thing to get a switch to appear, but attempting to
configure it breaks the whole thing. The VLAN has to be set up
perfectly, otherwise, interfaces will not start up, and one is forced to
reset settings, OR, the new LuCI feature kicks in and reverses any
steps. It is extremely difficult to determine which virtual ports
correspond to which physical ethernet ports without being able to set up
the switch in LuCI.
Temporary Workaround: followed directions here
[openwrt/luci#867](https://github.com/openwrt/luci/issues/867)
Reviewed-by: Marty Plummer <hanetzer@startmail.com>
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[commit author fix, subject fix, message text wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.
Hardware
--------
CPU: Atheros AR9344 (600 MHz)
RAM: 64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH: 1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V
Installation instructions:
1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
should be used.
Signed-off-by: Xavier Douville <github@douville.org>
This patch changes all the legacy usbdev leds triggers
to the use usbport. The problem is that the usbdev triggers
get applied as usbport in sysfs but LuCI gets confused and
is not able to show the configuration with usbdev. More
information can be found in the PR:
<https://github.com/openwrt/openwrt/pull/1819>
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[extended commit message]
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM and XW family, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
Also add the required package for this.
While at that, remove coefficients needed for PWM LEDs, as XM and XW
boards do not support PWM LEDs.
Tested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[Squashed commits + remove custom device_packages + slighty rewrite the commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The correct MAC address for this device is lan_mac +1, there is no
need to set lan_mac so use base_mac variable instead lan_mac.
Based on this PR for ath79:
https://github.com/openwrt/openwrt/pull/1726
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
[fix alphabetical ordering, reword subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB
Flash instruction:
- via web UI:
1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
2. Login to router and open the Advanced tab
3. Navigate to System Tools -> Firmware Upgrade
4. Upload firmware using the Manual Upgrade form
- via TFTP:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Keith Maika <keithm@aoeex.com>
Qxwlan E750G v8 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (PoE support)
- 2x 10/100/1000 Mbps Ethernet
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
While the stock firmware and previous ar71xx versions of openwrt used the
single ethernet port as a DHCP client, for unmodified openwrt usage it
makes more sense to do the standard openwrt thing and make the ethernet
port a static lan with known address so that users can find the device on
the network more easily.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
81d446b045 introduced incomplete
support for this device.
This patch attempts to correct the situation based on OEM source
code.
LED1-3 are GSM mode on OFW (2G/3G/4G) hence unassigned here.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: David Ehrmann <ehrmann@gmail.com>
This patch adds support for the MikroTik RB931-2nD (hAP mini):
https://mikrotik.com/product/RB931-2nD
Specifications:
* SoC: Qualcomm QCA9533 (650MHz)
* RAM: 32MiB
* Storage: 16MiB SPI NOR flash
* Ethernet: 3x100M
* Wireless: QCA9533 built-in, dual-chain 802.11b/g/n
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its Internet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Now connect the board via either of its LAN ports (2 or 3).
6. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
7. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
8. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Arvid E. Picciani <aep@exys.org>
This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on 3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot
Installation:
1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
- Boot device: try ethernet once then NAND
- Boot protocol: DHCP
- Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image, e.g.
openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
"try ethernet once then NAND," press and hold the reset button while
powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
pressed from the previous step.
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.
Revert to RouterOS
Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: David Ehrmann <ehrmann@gmail.com>
This commit adds support for the AVM Fritz!WLAN Repeater 450E
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4GHz WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- Most LEDs
Not working:
- 2 RSSI LEDs
AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
While it is possible to implement this feature, it would require an
additional kernel patch for a minor functionality.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.
Toggling a gpio selects the output to which USB is connected.
Since kernel 4.9, gpio base is rounded up to a value of 32.
Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.
But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.
Switching the USB port to mPCIe now shows my modem is correctly discovered again:
[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11
Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
This change was originally meant to go along with the ucidef_set_interface()
fixup.
Fixes: 7e664b7c2d ("base-files: fix ucidef_set_interface() protocol selection")
Fixes: 85048a9c1f ("base-files: rework _ucidef_set_interface to be more generic")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is a rework of previously submitted patch reworking
ucidef_set_interface_raw [1]. Here, keep the idea but instead
make _ucidef_set_interface more generic and use it instead of
ucidef_set_interface_raw.
Also change the users like ucidef_set_interface_lan and others.
[1] https://patchwork.ozlabs.org/patch/844961/
Signed-off-by: Roman Yeryomin <roman@advem.lv>
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0
Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Not working:
- USB port
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.
https://mikrotik.com/product/RB2011iLS-IN
Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
TP-Link Archer C60 v2 is a dual-band AC1350 router, based on
Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (web):
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use
OEM System Tools - Firmware Upgrade site.
Flash instruction (recovery):
1. Set PC to fixed IP address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and
rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Add support for TL-WR940N v6 board. It is pretty much the same as v5
except they only left WAN LED and removed other ones.
Installation: flash factory image through WEB UI or use TFTP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)
Flash instruction: use "factory" image directly in vendor GUI.
This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.
You can access vendor firmware over serial using:
- login: root
- password: linuxrocks
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
GainStrong Oolite V5.2 is a small (39.5 x 78 mm), dual-band system on
module, based on Qualcomm QCA9531 + QCA9887. All QCA9531 SOC GPIOs are
available on castellated pins.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet (all ports available on castellated pins)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887) with ext. FEM (SKY85710-11)
- 3x U.FL
- 1x USB 2.0
The dedicated development board includes 5 FE ports, USB 2.0 port, two
buttons (one directly connected to SOC reset input), header with all
GPIOs and several LEDs.
Flash instruction:
Vendor firmware is based on OpenWrt. LuCI or sysupgrade can be used to
flash OpenWrt firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
- combine support for Oolite/MiniBox V1.0 in single mach-*.c file
- fix model/board names
- include correct/full vendor name
- drop redundant package and factory image
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
