Commit Graph

698 Commits

Author SHA1 Message Date
Adrian Schmutzler
e4107e30a7 ar71xx: remove wrong MAC address adjustment for Archer C60 v2
The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac
is broken since a "mac" partition is not set up for this device on
ar71xx. Instead, the MAC address is already patched correctly in
11-ath10k-caldata.

Remove the useless adjustment.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit cbdc919024)
2020-03-14 13:20:23 +01:00
Adrian Schmutzler
83f1015a6c ar71xx: fix swapped LAN/WAN MAC address for Archer C60 v1/v2
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:

lan   *:7b   label
wan   *:7c   label+1
2.4g  *:7b   label
5g    *:7a   label-1

Only one address is stored in <&mac 0x8>, corresponding to the label.

This has been checked on revisions v1, v2 and v3.

Since ar71xx calculates the ath10k MAC address based on the ethernet
addresses, the number there is adjusted, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14eb54938b)
2020-03-14 13:20:18 +01:00
David Bauer
1713707673 ar71xx: add missing LED migration for Archer C7
When changing the LED names for the Archer C7 to represent the correct
color, a migration for existing UCI entries was not created.

Add a migration to keep existing LED configurations working.

Fixes commit c79c001b59 ("ar71xx: Archer C7 v1 LED names and RFKILL
fixes")

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4349d4c682)
2020-03-01 23:46:13 +01:00
Lech Perczak
1b4b4e3fae ar71xx: ubnt-rocket-m-ti: fix RSSI LED definitions
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti Rocket M Titanium, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.

While at that, split RSSI into ~equal intervals for 6 LEDs,
and remove coefficients needed for PWM LEDs, as this board does not
support PWM LEDs.

Finally, for complete support, enable 'rssileds' package in per-device
rootfs, so the indicator works out of box.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 83708f233d)
2020-01-21 14:10:13 +01:00
Sungbo Eo
27eea24921 ar71xx: fix MAC address setup for TL-WDR4300 board
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:

OpenWrt: lan = label_mac -2, wan = label_mac -2
  stock: lan = label_mac,    wan = label_mac +1

This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 9b02d32e34)
2019-12-21 00:31:39 +01:00
Adrian Schmutzler
8a21bc3622 ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2
As discussed in 1d18a14a90 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...

Fixes: FS#408

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a021268032)
2019-11-21 12:29:20 +01:00
Adrian Schmutzler
b3514e3569 ar71xx: improve support for TP-Link CPE510 v2
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.

Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).

With this patch, we provide proper support for this device in ar71xx.

Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
  for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254

Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c79b796280)
[added CPE510V2 entry to tplink-safeloader.c]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:13:27 +01:00
Tomislav Požega
5ec609815e ar71xx: fix WLAN LED names for Archer C7
Update WLAN LED colour identifier for both interfaces on Archer C7

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit 65762cdd22)
2019-07-28 23:27:39 +02:00
Tomislav Požega
be14b1feae ar71xx: fix system LED names on Archer C5/C7
Move system LED board definitions of Archer C5/C7 to reflect
actual system LED colour used

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit a73934fc9a)
2019-07-28 23:25:24 +02:00
Petr Štetiar
73b21559ce ar71xx: set mib-poll-interval on devices with ar8xxx switch
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.

So this patch sets mib-poll-interval to 500ms on devices which are using
ar8xxx switch LEDs trigger, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-05-20 21:19:48 +02:00
Adrian Schmutzler
f32e05c541 ar71xx: Fix network setup for TP-Link Archer C25 v1
Network for the Archer C25 v1 is set up without switch for no
obvious reason. The LED setup is even done switch-based.

This patch changes network setup so a switch is created.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-15 13:34:24 +02:00
Rosy Song
3b4c44aa8b ar71xx: mute script error in ar922x-led-fix script
This commit fixes following script error in syslog:

 cat: can't open '/sys/devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.4/ieee80211/phy*/name': No such file or directory
 sh: add: unknown operand
 sh: add: unknown operand

Signed-off-by: Rosy Song <rosysong@rosinson.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[commit subject and message tweaks]
2019-05-05 21:11:01 +02:00
Koen Vandeputte
e40050d104 ar71xx: add support for Mikrotik RouterBOARD 2011UiAS-2HnD r2
This board got a new hardware revision, without any change in functionality.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-23 13:22:31 +02:00
Adrian Schmutzler
93d23aced2 ar71xx: Correct MAC address for WAN interface of Archer C7 v5
This device shares the network config with v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.

Based on: https://github.com/openwrt/openwrt/pull/1726

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:05 +02:00
Petr Štetiar
0f8cdc28af ar71xx: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Robert Marko
99f6f2c0b8 ar71xx: Add support for TP-Link CPE210 v3
Looks identical to the v2.

This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-02 02:09:58 +02:00
Petr Štetiar
0a67e84bae ar71xx: ens202ext: Fix whitespace issues
I've missed leading whitespace issues in the original patch, so fixing
it in this commit. Thanks to pepe2k for letting me know.

Fixes: d260813d ("ar71xx: ens202ext: Fix VLAN switch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-01 12:07:09 +02:00
Michael Pratt
d260813d09 ar71xx: ens202ext: Fix VLAN switch
The target ENS202EXT was just recently added right before the stable
release of Openwrt 18.

It flashes fine, but the physical switch is almost impossible to use
until you have a VLAN set up. Tested on two devices.

The actual problem is that eth0 represents nothing for whatever reason.
In other words, both WAN and LAN are running from eth1. There may be an
underlying problem in the build, but for now, I assume that this is
correct and that a VLAN switch is an appropriate fix.

Also, it's virtually impossible to get the switch running right through
LuCI. It is one thing to get a switch to appear, but attempting to
configure it breaks the whole thing. The VLAN has to be set up
perfectly, otherwise, interfaces will not start up, and one is forced to
reset settings, OR, the new LuCI feature kicks in and reverses any
steps. It is extremely difficult to determine which virtual ports
correspond to which physical ethernet ports without being able to set up
the switch in LuCI.

Temporary Workaround: followed directions here
[openwrt/luci#867](https://github.com/openwrt/luci/issues/867)

Reviewed-by: Marty Plummer <hanetzer@startmail.com>
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[commit author fix, subject fix, message text wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-31 20:58:51 +02:00
Koen Vandeputte
e1444ab59c ar71xx: add support for MikroTik RouterBOARD 922UAGS-5HPacD
This patch adds support for the MikroTik RouterBOARD 922UAGS-5HPacD
with a built-in 802.11ac High-Power radio (31dBm).

See https://mikrotik.com/product/RB922UAGS-5HPacD for more info.

Specifications:
- SoC: Qualcomm Atheros QCA9557 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9882 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V
- SFP: 1x host
- USB: 1x 2.0 type A
- PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems)
- SIM slot: 1x mini-SIM

Working:
- Board/system detection
- NAND storage detection
- PCIe
- USB: Type A & mini PCIe
- Wireless
- Ethernet
- LED's (excl. SFP and RSSI levels)
- Reset button
- Sysupgrade

Not working:
- SFP cage

Installation:

- Boot vmlinux-initramfs image via BOOTP/TFTP and then flash sysupgrade
image using "sysupgrade -n"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-03-26 18:01:47 +01:00
Xavier Douville
5ac974f214 ar71xx: Add support for Mikrotik RB SXT 2nD r3
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.

Hardware
--------
CPU:   Atheros AR9344 (600 MHz)
RAM:   64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH:   1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V

Installation instructions:

1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
   DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
   no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
   openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
   should be used.

Signed-off-by: Xavier Douville <github@douville.org>
2019-03-22 00:40:29 +01:00
Adrian Schmutzler
51fb186cb3 ar71xx: Speed up caldata/eeprom handling
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.

This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.

Speed comparison @ TP-Link TL-WDR4300 (just manually) results
in a time reduction by three orders of magnitude (99.9 %).

> time dd if=/dev/mtd3 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096
4096+0 records in
4096+0 records out
real    0m 15.85s
user    0m 0.06s
sys     0m 13.28s

> time dd if=/dev/mtd3 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes
1+0 records in
1+0 records out
real    0m 0.02s
user    0m 0.00s
sys     0m 0.02s

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-03-13 16:27:41 +01:00
David Santamaría Rogado
e65f935de9 ar71xx: Change led trigger from usbdev to usbport
This patch changes all the legacy usbdev leds triggers
to the use usbport. The problem is that the usbdev triggers
get applied as usbport in sysfs but LuCI gets confused and
is not able to show the configuration with usbdev. More
information can be found in the PR:
<https://github.com/openwrt/openwrt/pull/1819>

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[extended commit message]
2019-02-28 11:34:48 +01:00
Andreas Ziegler
53c46b504c ar71xx: GL.iNet AR300M family: correct LED definitions
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2019-02-26 23:20:04 +01:00
Adrian Schmutzler
319c5d7c49 ar71xx: Fix 5 GHz MAC address for Archer C60 v2
Looks like C60 v2 needs the MAC address to be calculated
manually, while the C60 v1 gets it correctly without manual
interference.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-02-17 18:22:39 +01:00
Paul Wassi
78277ec162 ar71xx: fix TL-MR3220-v2 switch port order
Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
341311f319 ar71xx: fix TL-WR741ND-v4 switch port order
Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Lech Perczak
7ebbbda293 ar71xx: ubnt-(xm,xw): fix LED RSSI indication
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM and XW family, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.

Also add the required package for this.

While at that, remove coefficients needed for PWM LEDs, as XM and XW
boards do not support PWM LEDs.

Tested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[Squashed commits + remove custom device_packages + slighty rewrite the commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-08 17:27:47 +01:00
David Santamaría Rogado
4bcf581352 ar71xx: use correct wan mac address for the TP-Link Archer C7 v4
The correct MAC address for this device is lan_mac +1, there is no
need to set lan_mac so use base_mac variable instead lan_mac.

Based on this PR for ath79:
https://github.com/openwrt/openwrt/pull/1726

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
[fix alphabetical ordering, reword subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-30 12:24:07 +01:00
Rinki Kumari
dd02a19ff5
ar71xx: fix TP-Link Archer C7 v5 switch LEDs
Signed-off-by: Rinki Kumari <rinki13@gmail.com>
2018-11-17 16:27:38 +01:00
Pau Escrich
15f16bf05b ar71xx: add support for Gainstrong MiniBox V3.2
Adds MiniBox V3.2 ar71xx target (QCA99531 + QCA9887)
Info: http://oolite.cn/minibox-v3-2-qca9531-qca9887-module-pin-specification.html
Reference patch: http://oolite.cn/wp-content/uploads/2017/09/minibox_v3_cc15.05_20160325.patch
Installation: Upload firmware to uboot via HTTP at 192.168.1.1 (press button for 5 seconds)

Signed-off-by: Pau Escrich <p4u@dabax.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(daniel@makrotopia.org: rebased and fixed conflicts, fixed LED name,
                        added ath10k eeprom)
2018-11-15 19:49:51 +01:00
Thibaut VARÈNE
c6ee683d64 ar71xx: define switch for rb-952ui-5ac2nd
QCA9533 built-in switch can be configured

Tested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 18:14:30 +02:00
John Crispin
eddf4eae97 ar71xx: fix TL-WR1043N v5 port mapping
fixes 5660c8fb20 ("ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.")

Signed-off-by: John Crispin <john@phrozen.org>
2018-07-30 17:47:06 +02:00
Tim Thorpe
5660c8fb20 ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.
Reversed the numbering of the LAN ports in Luci so as to match the port numbers on the housing.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
2018-07-30 16:31:18 +02:00
Keith Maika
4caab80830 ar71xx: add support for TP-Link Archer C59 v2
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
2018-07-30 14:04:45 +02:00
张鹏
53a4502013 ar71xx:add support for E750G v8
Qxwlan E750G v8 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (PoE support)
 - 2x 10/100/1000 Mbps Ethernet
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
2018-07-30 10:43:36 +02:00
张鹏
ac03d51a3f ar71xx:add support for E750A v4
Qxwlan E750A v4 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 5G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (one port with PoE support)
 - 1x miniPCIe slot (USB 2.0 bus only)
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
2018-07-30 10:43:36 +02:00
张鹏
b74f63f81d ar71xx:add support for E558 v2
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.

Specification:

 - 720/600/200 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4 GHz (QCA9558)
 - 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
 - 4x miniPCIe slot (USB 2.0 bus only)
 - 1x microSIM slot
 - 5x LED (4 driven by GPIO)
 - 1x button (reset)
 - 1x 3-pos switch
 - 1x DC jack for main power input (9-48 V)
 - UART (JP5) and LEDs (J8) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
2018-07-30 10:43:36 +02:00
Daniel F. Dickinson
d2f7dba309 ar71xx: cap324: Use standard eth as static lan
While the stock firmware and previous ar71xx versions of openwrt used the
single ethernet port as a DHCP client, for unmodified openwrt usage it
makes more sense to do the standard openwrt thing and make the ethernet
port a static lan with known address so that users can find the device on
the network more easily.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Thibaut VARÈNE
091e915d99 ar71xx: improve MikroTik wAP R support
81d446b045 introduced incomplete
support for this device.

This patch attempts to correct the situation based on OEM source
code.

LED1-3 are GSM mode on OFW (2G/3G/4G) hence unassigned here.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: David Ehrmann <ehrmann@gmail.com>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE
5c2419b6f8 ar71xx: add missing diag LED support for RB wAP 2nD
3b15eb06c3 did not include diag.sh
edit

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE
e99f760235 ar71xx: rbspi: fix RB wAP AC gpio conflict and LED
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.

Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.

This patch fixes these issues and renames the corresponding #defines for
clarity

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE
c2d2647c09 ar71xx: add support for MikroTik RB931-2nD
This patch adds support for the MikroTik RB931-2nD (hAP mini):
https://mikrotik.com/product/RB931-2nD

Specifications:
  * SoC: Qualcomm QCA9533 (650MHz)
  * RAM: 32MiB
  * Storage: 16MiB SPI NOR flash
  * Ethernet: 3x100M
  * Wireless: QCA9533 built-in, dual-chain 802.11b/g/n

Installation:

1. Setup a DHCP/BOOTP Server with the following parameters:
   * DHCP-Option 66 (TFTP server name): pointing to a local TFTP
     server within the same subnet of the DHCP range
   * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
     of the to be booted image. The usable intramfs files are:
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
       - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin

2. Press the reset button on the board and keep that pressed.

3. Connect the board to your local network via its Internet port.

4. Release the button after the LEDs on the board are turned off.
   Now the board should load and start the initramfs image from
   the TFTP server.

5. Now connect the board via either of its LAN ports (2 or 3).

6. Upload the sysupgrade image to the board with scp:
     $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin

7. Log in to the running system listening on 192.168.1.1 via ssh
   as root (without password):
     $ ssh root@192.168.1.1

8. Flash the uploaded firmware file from the ssh session via the
   sysupgrade command:
     root@OpenWrt:~# sysupgrade /tmp/fw.bin

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-16 15:12:17 +02:00
Adrian Schmutzler
5c5bf8b865
ar71xx: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-23 16:06:31 +02:00
Arvid E. Picciani
bf39d5594b ar71xx: add support for TP-LINK Archer C7 v5
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Arvid E. Picciani <aep@exys.org>
2018-06-20 15:36:19 +02:00
David Ehrmann
81d446b045 ar71x: add support for Mikrotik Routerboard wAP R
This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on 3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.

Specifications:

- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot

Installation:

1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
  - Boot device: try ethernet once then NAND
  - Boot protocol: DHCP
  - Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
  - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
    server within the same subnet of the DHCP range
  - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
    of the to be booted image, e.g.
    openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
   "try ethernet once then NAND," press and hold the reset button while
   powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
   pressed from the previous step.

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.

Revert to RouterOS

Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: David Ehrmann <ehrmann@gmail.com>
2018-06-19 14:32:47 +02:00
David Bauer
b4bf43c667 ar71xx: add support for Fritz!WLAN Repeater 450E
This commit adds support for the AVM Fritz!WLAN Repeater 450E

SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - Most LEDs

Not working:
 - 2 RSSI LEDs
   AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
   control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
   While it is possible to implement this feature, it would require an
   additional kernel patch for a minor functionality.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-18 23:23:30 +02:00
David Bauer
daeab36c1b ar71xx: use Power-LED as Diag-LED on FRITZBox 4020
This commit makes use of the Power-LED as Diag-LED, allowing the LED to
work as a status indicator.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-09 13:45:29 +02:00
Koen Vandeputte
55b4b1eba0 ar71xx: fix USB switch to mPCIE for Mikrotik rb91x boards
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.

Toggling a gpio selects the output to which USB is connected.

Since kernel 4.9, gpio base is rounded up to a value of 32.

Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.

But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.

Switching the USB port to mPCIe now shows my modem is correctly discovered again:

[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11

Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
2018-06-08 09:31:35 +02:00
David Bauer
e36f8b3f39 ar71xx: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-07 09:31:58 +02:00
Luo chongjun
312d7a4a5a ar71xx: add support for GL.iNet GL-AR750S
This patch adds supports for GL-AR750S.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2018-05-27 09:26:09 +02:00