Commit Graph

21 Commits

Author SHA1 Message Date
Álvaro Fernández Rojas
e238c85e57 bcm63xx: nand: sercomm: switch to sercomm-load script
xxd is not a valid dependency and shouldn't be used.
Fixes buildbot failure.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 13:10:00 +02:00
Álvaro Fernández Rojas
a47acae319 bcm63xx: ad1018: support Sercomm factory images
This images can be flashed from the official firmware, as opposed to CFE
images, which can only be flashed from CFE and require opening the case.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 09:16:49 +02:00
Álvaro Fernández Rojas
f263a0f9ff bcm63xx: nand: support Sercomm firmwares
Add support for Sercomm factory firmwares (AES 256 CBC encrypted).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 09:12:05 +02:00
Daniele Castro
d6f66dd88e brcm63xx: add support for ADB P.DG A4001N A-000-1A1-AX
ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI)
has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected
to different GPIO PINs in active low configuration.

OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE.
It has different LEDs configuration and flash size/layout
w.r.t the ADB P.DG A4001N A-000-1A1-AX.

Hardware:
* Board ID: 96328avng
* SoC: Broadcom BCM6328
* RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01)
* LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, TX  NC  RX, on J5 connector (short R192 and R193)
                         NC  GND NC

Installation via CFE:
* Stock CFE has to be overwriten with one for 96328avng boards that can upload
  .bin images with no signature check (cfe-A4001N-V0000_96328avng.bin)
* connect a serial port to the board
* Stop the boot process after power on by pressing enter
* set static IP 192.168.1.2 and subnet mask 255.255.255.0
* navigate to http://192.168.1.1/
* upload the OpenWrt image file

Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-22 21:23:21 +02:00
Álvaro Fernández Rojas
78a0ae9023 bcm63xx: WIP: add Huawei HG253s v2 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-21 19:11:24 +02:00
Álvaro Fernández Rojas
5998c8f059 bcm63xx: nand: support CFE partition tags
Introduce support for generating JFFS2 CFE partition tags.
This is used in NAND devices in order to verify the integrity of the JFFS2
partition.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-21 19:11:24 +02:00
Álvaro Fernández Rojas
c93cdf536a bcm63xx: lzma-loader: rely on CHIP_ID for UART address
lzma-loader uart output wasn't working on BCM3380/BCM6362 because these
SoCs have the same processor ID.
Let's use CHIP_ID for establishing the UART base address.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-20 11:15:29 +02:00
Álvaro Fernández Rojas
8e8920c92f bcm63xx: lzma-loader: remove unused definitions
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-20 09:26:15 +02:00
Álvaro Fernández Rojas
0836e22a83 bcm63xx: image: add CVG834G CHIP_ID
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-20 09:23:10 +02:00
Álvaro Fernández Rojas
91b275b6e3 bcm63xx: image: rename CFE_CHIP_ID to CHIP_ID
Rename CFE_CHIP_ID to a generic name that doesn't involve CFE.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-20 09:21:34 +02:00
Álvaro Fernández Rojas
5f82691923 bcm63xx: add unmodded SERCOMM AD1018 support
Until now only HW modded SPI flash version was supported.

BCM6328 with 64M RAM and 128M NAND.
More info: https://openwrt.org/toh/sercomm/ad1018

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 13:33:39 +02:00
Álvaro Fernández Rojas
daee6b4661 bcm63xx: add Comtrend VG-8050 support
BCM63169 with 128M RAM, 128M NAND and BCM53125 switch.
Switch is connected by HSSPI to CS5.
More info: https://openwrt.org/toh/comtrend/vg8050

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 10:41:47 +02:00
Álvaro Fernández Rojas
62e7342ddf bcm63xx: add NETGEAR DGND3700v2 support
BCM6362 with 64M RAM, 32M NAND and BCM53125 switch.
Switch is connected by MMAP, which is currently unsupported (no VLANs).
More info: https://openwrt.org/toh/netgear/dgnd3700v2

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 10:41:42 +02:00
Álvaro Fernández Rojas
367a30389d bcm63xx: add support for Comtrend VR-3032u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Álvaro Fernández Rojas
86583384ff bcm63xx: smp: add NAND support
NAND controller is present on BCM6328, BCM6362, BCM6368 and BCM63268.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Álvaro Fernández Rojas
aa2f2276f7 bcm63xx: image: remove unused definition
KERNEL_ENTRY isn't used by lzma-loader.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:08 +02:00
Álvaro Fernández Rojas
a0081b1945 bcm63xx: loader-lzma: use default lzma
Specific CFE LZMA parameters aren't needed for LZMA Loader.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-12 12:34:57 +02:00
Álvaro Fernández Rojas
84646936a6 bcm63xx: image: rename LOADADDR to KERNEL_LOADADDR
Also remove KERNEL_ENTRY, since it's the same as KERNEL_LOADADDR

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-12 12:34:57 +02:00
Jonas Gorski
4e535d81ee bcm63xx: disable all devices with <= 4MiB flash and <= 32 MiB RAM
Device with 4 MiB flash and 32 MiB RAM won't be able to run OpenWrt in
a sufficient manner without tweaks, so don't build images for them by
default.

This includes all BCM6338, BCM6345 and BCM6348 "generic" devices,
as there are no supported devices of these with more than that.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2020-04-12 20:45:21 +02:00
Sungbo Eo
5b392c7119 treewide: gather DEVICE_VARS into one place
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.

For ramips, remove redundant values already present in parent file.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 19:55:12 +01:00
Adrian Schmutzler
e7bfda2c24 brcm63xx: rename target to bcm63xx
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-14 14:10:51 +01:00