This patch converts all apm821xx devices to the device-tree
board-detection method. All instances of the legacy
boardnames (mbl,mr24,...) are converted to "vendor,device"
identifier.
The custom board-detection code in apm821xx.sh is removed as
it no longer serves any purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch enables metadata-supported image verification
for all apm821xx supported devices. Since this method comes
with a built-in image verification tool (fwtool), the previous
image checks can be removed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Advantages:
- preserves existing partition layout. On the hard-drive.
Only the boot and rootfs partition will be overwritten.
Disadvantages:
- The upgrade process takes much longer to run.
from 2-3 seconds to 15-25 seconds.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-rootfs.img.gz
has to be written manually onto the disk. Please don't forget to backup
your configuration in this cases.
Note2: This patch requires
"base-files: upgrade: make get_partitions() endian agnostic"
Note3: If your current installation does not host the two
changes, sysupgrading will wipe the existing partition
layout. Don't forget to backup your data!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Please note that users with a Netgear WNDR4700
will need to update the device-tree partition
manually.
For instructions, please refere to commit 49856a4bb5
("apm821xx: make it possible to update the dtb partition on the WNDR4700")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the Cisco Meraki MX60/MX60W Security
Appliance. Flashing information can be found at
https://github.com/riptidewave93/LEDE-MX60
Specs are as follows:
AppliedMicro APM82181 SoC at 800MHz
1GiB NAND - Samsung K9K8G08U0D
512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC
Atheros AR8327-BL1A Gigabit Ethernet Switch
1x USB 2.0 Port
More info can be found at https://wiki.openwrt.org/toh/meraki/mx60
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
The insertion or removal of the sd-card cannot be detected
by the hardware itself. This is by design. To workaround this,
for the WNDR4700 unload/load the dwc2 module in case the
the special SD CARD GPIO line is low/high.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for Netgear Centria N900 WNDR4700/WNDR4720
hardware highlights:
CPU: AMCC PowerPC APM82181 Rev. E at 1000 MHz (PLB=166, OPB=83, EBC=83 MHz)
Security support, Boot ROM Location NAND wo/ECC 2k page (8 bits)
32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory
Board: AMCC APM82181 Evaluation Board, PCIE0/SATA1, 1*USB OTG
DRAM: 256 MB (ECC not enabled, 500 Mb/s, 32-bit, CL3)
NAND: 128 MiB (SLC, erase size: 128 KiB, page size: 2048, OOB size: 64)
ETH: Atheros AR8327N Gigabit Switch (4 x LAN, 1 x WAN)
USB: 2 x 3.0 (Renesas uPD720202K8-711-BAA-A, firmware not included)
SATA: 1 x SATA-II 3.5" Hard Drive Bay for HDDs (DesignWare SATA).
WLAN1: Atheros AR9380 5GHz 802.11an 3:3x3
WLAN2: Atheros AR9581 2.4GHz 802.11bgn 3:3x3
SDCARD: GL827L SD/MMC/MS Flash Card Reader (on internal dwc2 USB 2.0 host)
I2C: GMT G781 (i2c-0 @ 0x4d - lm90 compatible temperature sensor)
TC654 (i2c-0 @ 0x1b - Dual PWM fan Speed controller)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
INFO: Since this device only has a NAND chip. I opted for going with
root.squashfs in a UBI volume. There's no squashfs/jffs2 image.
This target produces three images.
a. netgear factory image
This image can be used to flash the Netgear WNDR4700 via the
firmware recovery mechanism and the web admin site.
The bootloader can be instructed to do a firmware recovery via the
# fw_recovery
command. It will start a tftp server and listen on 192.168.1.1
(the ipaddr variable in u-boot) for incoming, binary tftp clients.
The firmware recovery mechanism is also started if any of the flash
content which contains the kernel, device-tree definitions or the
(fake)rootfs fails to verify or load.
b. sysupgrade.tar image for sysupgrade
An sysupgrade will replace the entire current LEDE installation
with a newer version. This does include the kernel and the ubi rootfs
partition. The configuration can be carried over automatically as well
if desired.
simply copy the sysupgrade.tar to a the WNDR4700 running LEDE and run:
root@lede:~# sysupgrade sysupgrade.tar
and let it reboot.
Note: The devicetree flash area is NOT updated. Until the devicetree
definition is stable, this can lead to all sorts of hardware
detection problems! So make sure, if you experience issues: try
the fw_recovery. If you are unsure whenever this affects you:
test if you can reproduce your issue with the initramfs method.
As it will always have up-to-date device-tree definitions.
c. initramfs image for TFTP (for development and testing)
To use the initramfs method, follow the following steps:
1) Move the "lede-apm821xx-netgear-WNDR4700-initramfs-kernel.bin"
file to to the root directory of your TFTP server.
2) rename it to wndr4700.bin
3) On the WNDR4700 - Hit Enter during u-boot and insert:
# tftp 400000 wndr4700.bin; run addtty; bootm 400000 -
This will boot the LEDE image.
Note: The default tftp server is 192.168.1.7, if you want to change it:
# setenv serverip 192.168.8.7;
Note2: The default address for the WNDR4700 is 192.168.1.1:
# setenv ipaddr 192.168.8.8;
Note: Connect you tftp server on the last LAN port (not the WAN)
Note: The firmware for the USB 3.0 Host chip is not included anymore.
Therefore the two USB 3.0 ports will not work without the
uPD7070x-firmware package installed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware Highlights:
This patch adds support for Western Digital MyBook Live Series:
CPU: AMCC PowerPC UNKNOWN (PVR=12c41c83) at 800 MHz (PLB=200, OPB=100, EBC=100 MHz)
32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory
Board: Apollo-3G - APM82181 Board, 1*SATA
DRAM: 256 MB (2x NT5TU64M16GG-AC)
FLASH: 512 kB (SST 39VF040)
Ethernet: 1xRGMII - 1 Gbit - Broadcom PHY BCM54610
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The MyBook Live Duo additionally features a 1x USB 2.0 host port
and can support a second hard-drive.
This target produces two images for a target.
1. ext4 image
The extracted/raw image can be directly installed on
the internal HDD via "dd if=img.ext4 of=/dev/sdX".
This can either be done in place with the stock MyBook Live
firmware via ssh. Or by removing the HDD and writing the image
with a different PC.
The the compressed images are useful for sysupgrade.
2. recovery.tar image for TFTP and Serial.
extract the recovery.tar to a TFTP server directory.
On the MyBook Live (Duo) serial port - Hit Enter during u-boot and insert:
# setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1; run net_self
Where 192.168.1.254 is your TFTP server.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds a new target for PowerPC APM82181 and APM82161
(464-based) boards, as well as adds support for the booke-wdt
watchdog package.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
