Contains the following change
eeef7b5 blobmsg_json: blobmsg_format_string: do not escape '/'
Resolves FS#2147
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The change was made with the following commands
cd package/utils/busybox/config
../convert_menuconfig.pl ~/git-repo/openwrt/openwrt/build_dir/target-mips_24kc_musl/busybox-1.30.1
convert_defaults.pl has no changes other than overwriting defaults for
BUSYBOX_DEFAULT_FEATURE_IPV6
Resolves FS#2146
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This is to align with upstream change 72089cf ("config: deindent all
help texts") and to make the follow-up change syncing Config.in files
with current busybox version more reviewable
It was made with the following commands
cd package/utils/busybox/config
find . -name 'Config.in' | xargs sed -ir -e 's/^\t \([^ ]\)/\t\1/'
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
consolidate patch 651-rt2x00-remove-unneccesary-code.patch.
fixup the most obvious whitespace problems in RXIQ and TX-LOFT code.
always backup registers bbpr1, bbpr4, bbpr241 and bbpr242 to avoid
compiler warning about them being potentially uninitialized.
no functional changes (intended)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All supported boards should work with the $vendor bootloader just fine.
Existing users should mindfully re-flash using new initramfs build and
restore $vendor bootloader's bootcmd to it's original setting.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add port handles for both USB 2.0 ports so they can be used as
trigger-source for USB LEDs.
Suggestions for pogoplug and akitio,mycloud devices are welcome.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use tested values on shuttle,kd20 and assumed values for
mitrastar,stg-212 and cloudengines,pogoplug*.
akitio users have yet to report back stock flash layout to support
vendor bootloader environment there as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ar has a deterministic (-D) and non-deterministic (-U) mode.
OpenWrt is already using the deterministic mode by default,
but ncurses' configure script force this to be non-deterministic.
Since autoreconf fails to generate a new configure, the configure script
is directly modified.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
When autoloading more than one modules per packages,
/etc/modules.d/$module depends on the file system ordering.
To test this: use disorderfs on the build_dir and build kmod-sched.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
add kernel and other missing NAND flash partitions to allow booting
using stock loader instead of the 2nd-stage bootloader.
This will ease installation from stock firmware on pogoplugs as well
as stg212 aka. medion nas.
Existing users of OpenWrt on those boards will have to boot initramfs
generated after this commit and subsequently flash first the ubinized
image, then again run initramfs to flash sysupgrade.tar image, and
then restore bootcmd in U-Boot environment back to the original setting
('nboot 60500000 0 440000' or something like that) instead of jumping
into the now no longer used 2nd-stage loader.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should
be used as a portmask instead of "0x1e" for "WAN" LED configuration.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch changes all the legacy usbdev leds triggers
to the use usbport. The problem is that the usbdev triggers
get applied as usbport in sysfs but LuCI gets confused and
is not able to show the configuration with usbdev. More
information can be found in the PR:
<https://github.com/openwrt/openwrt/pull/1819>
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[extended commit message]
In the production of glinet, the MAC address of ethernet port is
only written at the position where the ART area offset address
is 0, and the MAC address of eth1 is added 1 on the basis of eth0.
Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds support for the AVM FRITZ!Box 7530.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [PKG_RELEASE]
The current eva_ramboot.py script is currently only compatible with
Lantiq based AVM devices. For IPQ40xx devices, the offset needs to be
changed. Also an alignment is not necessary here.
Adjust the script to be able to pass an optional offset to load the
image to. In case no offset is provided, the script behaves exactly as
before this commit.
Signed-off-by: David Bauer <mail@david-bauer.net>
From: Niklas Cassel <niklas.cassel@linaro.org>
|The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
|triggered interrupt.
|
|The msi_ctrl_int will be high for as long as any MSI status bit is set,
|thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
|IRQ handler to keep getting called, as long as any MSI status bit is set.
|[...]
|Not having the correct IRQ type defined will cause us to lose interrupts,
|which in turn causes timeouts in the PCIe endpoint drivers.
|
|Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
|Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
David Bauer reported that the VDSL modem (attached via PCIe)
on his AVM Fritz!Box 7530 was complaining about not having
enough space in the BAR. A closer inspection of the old
qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed:
| qcom,pcie@80000 {
| compatible = "qcom,msm_pcie";
| reg = <0x80000 0x2000>,
| <0x99000 0x800>,
| <0x40000000 0xf1d>,
| <0x40000f20 0xa8>,
| <0x40100000 0x1000>,
| <0x40200000 0x100000>,
| <0x40300000 0xd00000>;
| reg-names = "parf", "phy", "dm_core", "elbi",
| "conf", "io", "bars";
Matching the reg-names with the listed reg leads to
<0xd00000> as the size for the "bars".
BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch removes the obsolete touchscreen config symbols
and all disables all remaining ones in the generic config.
Generated by running drivers/input/touchscreen/Kconfig
sed -n 's/^config[[:space:]]\(.*\)/# CONFIG_\1 is not set/p' Kconfig |\
sort -d
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the disabled DRM_RADEON and DRM_AMDGPU
config symbols from the x86' config to the generic target
configs. The existing symbols in the x86' configs are kept
for now, until we know whenever we want to remove such
symbols or not (see Github PR #1831, #1825, #1828).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Qxwlan E2600AC C1 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
FLASH: 32 MiB Winbond W25Q256
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Qxwlan E2600AC C2 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
NOR: 16 MiB Winbond W25Q128
NAND: 128MiB Micron MT29F1G08ABAEAWP
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "ubi" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.
Specifications:
- AR9344 SoC
- 535/400/267 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 5 GHz, up to 25 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while while the WAN LED flashes, until it starts flashing
faster. Once in failsafe mode, perform a factory reset as usual.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and
keep it pressed for >10 seconds. The recovery page will be at
http://192.168.1.1
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n
Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED
Flash instruction:
The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
the router and keep button pressed for around 10 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Marcel Jost <majo@icutech.ch>
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch
Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* wg-quick: freebsd: allow loopback to work
FreeBSD adds a route for point-to-point destination addresses. We don't
really want to specify any destination address, but unfortunately we
have to. Before we tried to cheat by giving our own address as the
destination, but this had the unfortunate effect of preventing
loopback from working on our local ip address. We work around this with
yet another kludge: we set the destination address to 127.0.0.1. Since
127.0.0.1 is already assigned to an interface, this has the same effect
of not specifying a destination address, and therefore we accomplish the
intended behavior. Note that the bad behavior is still present in Darwin,
where such workaround does not exist.
* tools: remove unused check phony declaration
* highlighter: when subtracting char, cast to unsigned
* chacha20: name enums
* tools: fight compiler slightly harder
* tools: c_acc doesn't need to be initialized
* queueing: more reasonable allocator function convention
Usual nits.
* systemd: wg-quick should depend on nss-lookup.target
Since wg-quick(8) calls wg(8) which does hostname lookups, we should
probably only run this after we're allowed to look up hostnames.
* compat: backport ALIGN_DOWN
* noise: whiten the nanoseconds portion of the timestamp
This mitigates unrelated sidechannel attacks that think they can turn
WireGuard into a useful time oracle.
* hashtables: decouple hashtable allocations from the main device allocation
The hashtable allocations are quite large, and cause the device allocation in
the net framework to stall sometimes while it tries to find a contiguous
region that can fit the device struct. To fix the allocation stalls, decouple
the hashtable allocations from the device allocation and allocate the
hashtables with kvmalloc's implicit __GFP_NORETRY so that the allocations fall
back to vmalloc with little resistance.
* chacha20poly1305: permit unaligned strides on certain platforms
The map allocations required to fix this are mostly slower than unaligned
paths.
* noise: store clamped key instead of raw key
This causes `wg show` to now show the right thing. Useful for doing
comparisons.
* compat: ipv6_stub is sometimes null
On ancient kernels, ipv6_stub is sometimes null in cases where IPv6 has
been disabled with a command line flag or other failures.
* Makefile: don't duplicate code in install and modules-install
* Makefile: make the depmod path configurable
* queueing: net-next has changed signature of skb_probe_transport_header
A 5.1 change. This could change again, but for now it allows us to keep this
snapshot aligned with our upstream submissions.
* netlink: don't remove allowed ips for new peers
* peer: only synchronize_rcu_bh and traverse trie once when removing all peers
* allowedips: maintain per-peer list of allowedips
This is a rather big and important change that makes it much much faster to do
operations involving thousands of peers. Batch peer/allowedip addition and
clearing is several orders of magnitude faster now.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
This is bugfix release that incorporated all of the devcrypto engine
patches currently in the tree.
The cleaning procedure in Package/Configure was not removing the
dependency files, causing linking errors during a rebuild with
different options. It was replaced by a simple make clean.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
omcproxy's configuration is lost on every update or installation.
Avoid it by defining the configuration file.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
After update to 5.0.1 iw-full package failed to display command list on
ipq40xx arch. Root cause was found to be LTO reordering causing
incorrect detection of command struct size in:
iw.c:552
cmd_size = labs((long)&__section_set - (long)&__section_get);
This reverts commit ef16a394d2.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.
With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.
Signed-off-by: David Bauer <mail@david-bauer.net>
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This can break for example 5GHz meshpoint interfaces
because 0 maps to a CCK rate (11Mbit/s).
It must also be avoided that the ath10k-ct internal state for the rates is
not synced with the mac80211 rates state. Otherwise, the user specified
rate (e.g. a wifi-iface mcast_rate for a meshpoint interface) will only be
set on startup. And a short while after that, ath10k-ct specific code in
ath10k_check_apply_special_rates is missing a valid rate in its own
structures and is then recalculating a new default rate. This default rate
is in most situations not the requested rate.
Fixes: 4df3c71cd4 ("ath10k-ct: Update to 2018-12-11 and use version based on 4.19")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This breaks for example 5GHz meshpoint interfaces because
0 maps to a CCK rate (11Mbit/s).
Fixes: db90c243a0 ("mac80211: update to version based on 4.19-rc4")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
