b43legacy needs ssb support and we do not compile the mips74 subtarget
of the brcm47xx target with SSB support. This causes a build failure in
the mac80211 package and only some of the kernel modules are being
created.
I am not aware of any device with a BRCM47xx mips74 CPU which uses a
b43legacy compatible device.
Fixes: FS#2334
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After commit e82a4d9cfb ("config: regenerate *_shipped sources") the mconf
parser became more strict as a side effect and started to spew a series of
warnings when evaluating our generated kconfig sources:
tmp/.config-package.in:705:warning: ignoring unsupported character '@'
The root cause of these warnings is a wrong use of the @SYMBOL dependency
syntax in various Makefile. Fix the corresponding Makefiles by turning
`@SYM||@SYM2` expressions into the proper `@(SYM||SYM2)` form.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This improves FullMAC firmware compatibility, adds logging in case of
firmware crash and *may* fix "Invalid packet id" errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
https://www.gpo.gov/fdsys/pkg/CFR-2013-title47-vol1/pdf/CFR-2013-title47-vol1-sec15-247.pdf
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware
Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies
according to original Kconfig and lsmod output
This will remove some unnecessary packages from MT7620 target to
save some space
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[75 characters per line in the commit message]
No target is using kernel 3.18 anymore, remove all the generic
support for kernel 3.18.
The removed packages are depending on kernel 3.18 only and are not used on
any recent kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 4.1, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
struct ieee80211_local needs to be passed in separately instead of
dereferencing the (potentially NULL) sdata
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Replace the patch introduced by commit d0b969eee8 ("mac80211: rt2x00:
do not increment sequence number while re-transmitting") was merged
into wireless-drivers.git. Replace our version with the merged version.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The removed patches are now integrated in the upstream kernel.
Refresh all patches on top of the new backports release.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
The keyword "all" is only supported by `iw set antenna` if
it's used as the only argument.
Convert "all" into a mask before calling `iw set antenna`.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Imported from patchwork, patches marked with '=' have already been in
our tree:
[v3,1/4] cfg80211: add ratelimited variants of err and warn
[v3,2/4] rt2x00: use ratelimited variants dev_warn/dev_err
[v3,3/4] rt2x00: check number of EPROTO errors
=[v3,4/4] rt2x00: do not print error when queue is full
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently STA+AP re-transmitting the management frames with
incremented sequence number if hardware is assigning the sequence.
Fix is to assign the sequence number for Beacon by hardware
and for other Management frames software will assign the
sequence number
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
ieee80211w support is only activated in hostapd when at least one
capable driver is build into the image. Many drivers which are capable
of ieee80211 (MFP) and have the MFP_CAPABLE set in the driver are still
missing the DRIVER_11W_SUPPORT dependency. Add this to more driver
capable of ieee80211w.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
consolidate patch 651-rt2x00-remove-unneccesary-code.patch.
fixup the most obvious whitespace problems in RXIQ and TX-LOFT code.
always backup registers bbpr1, bbpr4, bbpr241 and bbpr242 to avoid
compiler warning about them being potentially uninitialized.
no functional changes (intended)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This breaks for example 5GHz meshpoint interfaces because
0 maps to a CCK rate (11Mbit/s).
Fixes: db90c243a0 ("mac80211: update to version based on 4.19-rc4")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This should fix the WDS / 4addr mode with ath10k and probably other
devices.
This patch was found here: https://patchwork.kernel.org/patch/10692383/
Fixes: d9eefa7a70 ("mac80211: rebase ontop of v4.18.5")
Reported-by: Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix crash due to passing invalid r2x00dev->eeprom_file pointer to
release_firmware(). Since we copy eeprom data with EEPROM_SIZE
in rt2800_read_eeprom() we can use eeprom_file->size as marker
if the file was crated by request_firmware().
Acked-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cherry-pick Multi-AP commits from uptream:
9c06f0f6a hostapd: Add Multi-AP protocol support
5abc7823b wpa_supplicant: Add Multi-AP backhaul STA support
a1debd338 tests: Refactor test_multi_ap
bfcdac1c8 Multi-AP: Don't reject backhaul STA on fronthaul BSS
cb3c156e7 tests: Update multi_ap_fronthaul_on_ap to match implementation
56a2d788f WPS: Add multi_ap_subelem to wps_build_wfa_ext()
83ebf5586 wpa_supplicant: Support Multi-AP backhaul STA onboarding with WPS
66819b07b hostapd: Support Multi-AP backhaul STA onboarding with WPS
8682f384c hostapd: Add README-MULTI-AP
b1daf498a tests: Multi-AP WPS provisioning
Add support for Multi-AP to the UCI configuration. Every wifi-iface gets
an option 'multi_ap'. For APs, its value can be 0 (multi-AP support
disabled), 1 (backhaul AP), 2 (fronthaul AP), or 3 (fronthaul + backhaul
AP). For STAs, it can be 0 (not a backhaul STA) or 1 (backhaul STA, can
only associate with backhaul AP).
Also add new optional parameter to wps_start ubus call of
wpa_supplicant to indicate that a Multi-AP backhaul link is required.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Those have by now been merged into wireless-drivers-next:
17ae2acd1a6f rt2x00: remove unneeded check
5991a2ecd070 rt2x00: remove confusing AGC register
9ad3b5565445 rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
7aca14885ede rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
c7ff1bfeaf1c rt2800: comment and simplify AGC init for RT6352
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
backport from wireless-drivers-next, replacing some existing patches in
our tree (marked with '=' are those which were already present):
f483039cf51a rt2x00: use simple_read_from_buffer()
=5c656c71b1bf rt2800: move usb specific txdone/txstatus routines to rt2800lib
=0b0d556e0ebb rt2800mmio: use txdone/txstatus routines from lib
=5022efb50f62 rt2x00: do not check for txstatus timeout every time on tasklet
=adf26a356f13 rt2x00: use different txstatus timeouts when flushing
=0240564430c0 rt2800: flush and txstatus rework for rt2800mmio
6eba8fd22352 rt2x00: rt2400pci: mark expected switch fall-through
10bb92217747 rt2x00: rt2500pci: mark expected switch fall-through
916e6bbcfcff rt2x00: rt2800lib: mark expected switch fall-throughs
641dd8068ecb rt2x00: rt61pci: mark expected switch fall-through
750afb08ca71 cross-tree: phase out dma_zalloc_coherent()
=c2e28ef7711f rt2x00: reduce tx power to nominal level on RT6352
a4296994eb80 rt2x00: Work around a firmware bug with shared keys
2587791d5758 rt2x00: no need to check return value of debugfs_create functions
pending on linux-wireless:
rt2x00: remove unneeded check
rt2x00: remove confusing AGC register
rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
rt2800: comment and simplify AGC init for RT6352
rt2x00: do not print error when queue is full
rt2800: partially restore old mmio txstatus behaviour
rt2800: new flush implementation for SoC devices
rt2800: move txstatus pending routine
rt2800mmio: fetch tx status changes
rt2800mmio: use timer and work for handling tx statuses timeouts
rt2x00: remove last_nostatus_check
rt2x00: remove not used entry field
rt2x00mmio: remove legacy comment
While at it also rename some existing patches now that there are
separate folders with patches for each driver to make things a bit
nicer to handle.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This updates mac80211 to backports version 4.19.23-1 which includes all
the stable fixes from kernel 4.19.23.
The removed patches are included in this version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
