Without this patch the switch config for the adm switch did not worked,
because hey are not names eth0.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41512
Old OpenWrt releases were using network configs that are not valid
anymore. They were specifying ports tagging in a different way (or were
not tagging CPU at all) and were using VID 0 which is a reserved value.
Modifying network configuration to apply all needed changes would be
pretty tricky. Script /etc/init.d/netconfig that generates new config is
quite complex itself.
So instead let's save the most important settings, regenerate config
from the scratch and restore values. This should work for 99% of users.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41500
This fixes some strange problems with tg3. I assume that the Ethernet
driver was not brought up if the switch was named switch0.
This was reported and tested by ernesto (Faulp3lz).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41042
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
Instead of looking into the proc entry provided by broadcom-diag use
the board info from /proc/cpuinfo to get the board we are on.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39256
Use the new led api also on brcm47xx.
The led for failsafe indication is searched for.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39255
Remove the code used on the old switch driver.
The Ethernet drive is loaded as a module and needs some time to get up
therefor we added some wait function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39254
Some time ago, after switching to the mainline bcm47xxpart driver
following patch has been applied:
commit 03cef8725d2062335ffc3de50fc037b294fd458c
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sat Apr 6 22:22:26 2013 +0000
brcm47xx: use old partition names again for kernel 3.8
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
I propose to revert this change and make sysupgrade use "firmware"
instead. This makes brcm47xx compatible with widely used ar71xx and
after all "firmware" sounds like a much better name for... the firmware.
This change doesn't affect "sysupgrade" usage, because it never takes a
partition name as a parameter. This change only affects users using mtd
tool directly. Hopefully there are not many howtos using "mtd" command.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38973
Modify /etc/init.d/netconfig to use UCI defaults for building the
default network config, which includes appropriate defaults for IPV6.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38294
This makes it possible to use swconfig to controll the switch.
This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.
SVN-Revision: 37304
This fixes some problems with the switch handling
* It now send the messages again to indicate a button for failsafe mode should be pressed
* it does not leak packages between wan and lan any more
* the switch works again in normal mode
The Ethernet connection has to be up when the switch driver switch-robo
is insmoded therefor we just do it again.
Explicitly set enable_vlan to prevent leaking packages.
This should close#13869, #13868 and #13716
SVN-Revision: 37286
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
SVN-Revision: 36235
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.
This makes OpenWrt always use vlan1 and vlan2 instead.
SVN-Revision: 35704
This contains the following new bigger changes:
* new partition parser which still could lake some features or have bugs
* new nand flash driver
* using physmap-flash flash driver for parallel flash
* some changes to the serial flash driver
With these changes OpenWrt starts using more of the mainline flash drivers.
SVN-Revision: 35632
The included patch will generate a correct network configuration on the simpletech simpleshare.
Thank you for the patch Will Holmes (RealOpty)
This closes#12361.
SVN-Revision: 35623
Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm. The list of devices will need to
be expanded. Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists? Could
a similar method be used in "/etc/init.d/netconfig"?
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35491
This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.
Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.
SVN-Revision: 34995
The behaviour of calling 'mount' differed depending on whether it called
the busybox-mount, the mount of util-linux, the mount defined in
/lib/functions.sh and /lib/functions/boot.sh
/etc/preinit even included /lib/functions.sh and /lib/functions/boot.sh,
both re-defining 'mount'.
SVN-Revision: 34792
Sometimes the port 0 was the WAN port or there could be some device
where the port 0 is not wired to an actual Ethernet port. Now telnet in
failsafe will listen on all ports of the switch so user do not have to
search for the correct port any more. This change will make the switch
leak traffic between the WAN and the LAN port, but you should not use
failsafe while connected to a untrusted network.
SVN-Revision: 33544
Hi,
this patch adds the correct vlan definitions for the Siemens SE505v2. It
applies to trunk as well as backfire (please apply here too). On
backfire this also patches brcm-2,4, because brcm47xx base-files is just
symlinked to brcm-2.4.
It also fixes two whitespace issues.
Tested with brcm47xx on both trunk and backfire branch and works as
expected.
Signed-off-by: Manuel Munz <freifunk@somakoma.de>
SVN-Revision: 28336
