set_config causes the ucode bss resource to be re-created and because of that
the bss list needs to be updated as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f429bd94f99e system-linux: switch to new ETHTOOL_xLINKSETTINGS API
Fixes AN announcement for speeds beyond 1 GBit/s.
Adds new UCI options for Ethernet devices:
- autoneg: switch on or off auto-negotiation
- pause: if set to 0, do not announce symmetric flow control capability
- asym_pause: if set to 0, do not announce asymmetric flow control
capability.
- rxpause: if set overrides AN and forces RX pause accordingly
- txpause: if set overrides AN and forces TX pause accordingly
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
db3934d2f740 scripts/netifd-wireless.sh: properly fix WPA3 Enterprise support
Support the following values for the different WPA3 Enterprise modes:
- wpa3-mixed: WPA3 Enterprise transitional mode
This supports EAP with both SHA1 and SHA-256, with optional MFP
- wpa3: WPA3 Enterprise only mode
This supports only SHA256 with mandatory MFP
- wpa3-192: WPA3 Enterprise with mandatory 192 bit support
This uses only GCMP-256 ciphers
Disable 192 bit support and GCMP-256 ciphers for the regular "wpa3" mode.
It seems that even leaving in optional 192 bit support breaks auth on some
clients, including iOS devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
WPA3 Enterprise-transitional requires optional MFP support and SHA1+SHA256
WPA3 Enterprise-only requires SHA1 support disabled and mandatory MFP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems that this was not functioning properly and was likely completely unused.
Keeping this out of tree also introduced some annoying churn when updating, because
of the iw nl80211.h sync patch.
If this is needed, it will be reintroduced when/if it is added upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the STA is brought up, it is set to DISABLED before adding the bss to ucode,
so the first trigger to disable the AP is missed.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit e978072baaca ("Do prune_association only after the STA is
authorized") causes issues when an STA roams from one interface to
another interface on the same PHY. The mt7915 driver is not able to
handle this properly. While the commits fixes a DoS, there are other
devices and drivers with the same limitation, so revert to the orginal
behavior for now, until we have a better solution in place.
Fixes: #13156
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
It cannot be properly cloned, since it is attached to the resource type.
Use a separate registry for data. Fixes object confusion issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
An active client mode interface could prevent the AP from claiming its channel
and mess up the bringup sequence order
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop obsolete control interface patches.
This fixes some corner cases in the previous code where the segment 0 center
frequency was not adjusted properly, leading to logspam and non-working AP
interfaces.
Additionally, shutting down the AP was broken, because the next beacon update
would re-enable it, leading to a race condition on assoc.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes this error: hostapd: nl80211: kernel reports: integer out of range
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check the phy before removing unrelated netdevs on the same hw device
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When building xdp-tools with CONFIG_USE_LLVM_HOST=y, on a host that
enabled stack protector by default in Clang, compilation fails with the
following error:
CLANG xdp-dispatcher.o
clang-16: error: ignoring '-fstack-protector-strong' option as it is not currently supported for target 'bpfeb' [-Werror,-Woption-ignored]
Add -fno-stack-protector to BPF_CFLAGS to fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Include AP ucode source file
Fixes: e56c5f7b27 ("hostapd: add ucode support, use ucode for the main ubus object")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
8c2758b4fbbb wireless: add support for replacing data blobs at runtime
0ff22a6a68ce wireless: enable dynamic reconfiguration by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This implements vastly improved dynamic configuration reload support.
It can handle configuration changes on individual wifi interfaces, as well
as adding/removing interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used to run a standalone EAP server that can be used from
other APs. It uses json as user database format and can automatically
handle reload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
At least Fedora and RHEL 9 set RSAMinSize=2048, so when trying to use
failsafe, we get 'Bad server host key: Invalid key length'
To workaround the issue, we can use: ssh -o RSAMinSize=1024 ...
Generating 2048 bits RSA is extremely slow, so add ed25519.
We keep RSA 1024 to be as compatible as possible.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
