Commit Graph

58602 Commits

Author SHA1 Message Date
David Bauer
8037417744 mpc85xx: correct WS-AP3715i eth LED assignment
Ethernet LED assignments were incorrectly swapped. Fix the assignment
logic so the correct LED is illuminated for the LAN LEDs.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-09-21 01:10:40 +02:00
Felix Fietkau
4145ff4d8a hostapd: add missing NULL pointer check in uc_hostapd_iface_stop
Avoid crashing if the interface has already been removed

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-20 18:40:33 +02:00
Andreas Böhler
7354d17ff4
ipq4019: add support for ZTE MF282 Plus aka DreiTube
The ZTE MF282 Plus is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF286/MF287 but in the form factor
of the MF282.

Specifications
==============

SoC: IPQ4019
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 1x GBit LAN
LTE: ZTE Cat6
WiFi: 802.11a/b/g/n/ac SoC-integrated

MAC addresses
=============

LAN: from config
WiFi 1: from config + 1
WiFi 2: from config + 2

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x84000000 openwrt.bin
  bootm 0x84000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m9
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd9 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd9 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock9 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 9
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to the MF286R, it provides an RNDIS interface
and an AT interface.

Other Notes
===========

There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-20 14:29:20 +02:00
John Audia
ac422c9788
kernel: bump 5.15 to 5.15.132
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.132

Removed upstreamed:
	bcm53xx/patches-5.15/037-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[1]
	bcm53xx/patches-5.15/037-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[2]
	bcm53xx/patches-5.15/037-v6.6-0008-ARM-dts-BCM5301X-Extend-RAM-to-full-256MB-for-Linksy.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=b35f3ca1877e024887df205ede952863d65dad36
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=2840d9b9c8750be270fb1153ccd5b983cbb5d592
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=f086e859ddc252c32f0438edff241859c0f022ce

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-20 14:13:00 +02:00
Felix Fietkau
e9722aef9e hostapd: fix a crash when disabling an interface during channel list update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-20 14:11:14 +02:00
Alexander Couzens
bcf02c5d31
toolchain: assign PKG_CPE_ID
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has a CPE id.

Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2023-09-19 20:22:59 +02:00
Alexander Couzens
02f86a0765 tools: assign PKG_CPE_ID
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining tools which have a CPE ID.
Not every tool has CPE id.

Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2023-09-19 20:21:33 +02:00
Alexander Couzens
8572007f90 packages: assign PKG_CPE_ID for all missing packages
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.

Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2023-09-19 20:21:13 +02:00
John Audia
eecb582a0f
sdk: add cpupower to userspace sources
For https://github.com/openwrt/packages/pull/21533 to be merged,
this source tree is needed to be included.

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-19 14:17:20 +02:00
Robert Marko
d6ac365e42
mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.

The same image can be used on both versions as U-Boot will enable the
switch node and disable the unused ethernet controller.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
Robert Marko
2bb418299d
uboot-mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.

In order to use the same image for both boards, U-Boot is responsible for
detecting the revision and enabling/disabling DTS nodes.
So, to make it easy for users, lets add the pending U-Boot patches to build
in OpenWrt.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
Robert Marko
0b6d62c50b
generic: 6.1: backport support for Marvell 88E6361 switch
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
Robert Marko
39227de5e5
generic: 5.15: backport support for Marvell 88E6361 switch
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.

Since 5.15 doesnt have phylink_get_caps I had to modify the backport to
use the old mv88e6393x_phylink_validate instead.
I had to fixup one more instance of port_max_speed_mode as well that is not
present in 6.5.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
Felix Fietkau
f52e008d04 netifd: update to the latest version
7a58b995fdbe wireless: update prev_config on SET_DATA notify

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-19 11:56:30 +02:00
Felix Fietkau
a511480368 hostapd: use phy name for hostapd interfaces instead of first-bss ifname
Improves reliability in error handling

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-19 11:56:30 +02:00
Andreas Böhler
053f8f92d1
ipq40xx: ZTE MF287 series: move to gpio-export for modem-reset GPIO
Turn the "gpio-restart" node into a "gpio-export" node for all MF287
variants, similar to the MF287 Pro. Unfortunately, there doesn't seem to be
a "power button blocker" GPIO for the MF287 and MF287 Plus, so a modem
reset always triggers a system reset.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-19 11:43:36 +02:00
Andreas Böhler
9c7578d560
ipq40xx: refactor ZTE MF287 series
The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-19 11:43:36 +02:00
Pascal Coudurier
5602665255
x86: add 6.1 testing kernel
Enable building with 6.1 as testing kernel

Compile-tested: x86_64, x86_generic, x86_legacy, x86_geode
Run-tested: x86_64, x86_generic (qemu), x86_legacy (qemu)

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:38 +02:00
Pascal Coudurier
dc471652fe
kernel: modules: video: adapt drm-amdgpu and drm-radeon for kernel 6.1
Package and add dependencies to drm-amdgpu and drm-radeon for 6.1
 * package acpi-video, drm-display-helper and drm-buddy
 * add acpi-video, drm-display-helper and drm-buddy as dependencies for
   drm-amdgpu
 * add acpi-video and drm-display-helper as dependencies for drm-radeon

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:37 +02:00
Pascal Coudurier
e9dc4ff22d
kernel: modules: netdevices: adapt mlx5-core for kernel 6.1
Set CONFIG_MLX5_VFIO_PCI=n for kernel greater than 5.18

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:37 +02:00
Pascal Coudurier
ce098f4791
kernel: modules: hwmon: adapt nct6775 for kernel 6.1
nct6775 module splited in 5.19 kernel:
* add nct6775-core module @ge5.19
* add regmap dependency for 6.1

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:37 +02:00
Pascal Coudurier
af52f72f94
x86: refresh kernel configs for 6.1
refresh and add missing symbols for target and subtargets

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:37 +02:00
Pascal Coudurier
2e89ef1824
x86: copy 5.15 configs to 6.1
Copy 5.15 configs to 6.1 as a starting point

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:36 +02:00
Pascal Coudurier
b2c0e75c25
x86: refresh patches for 6.1
Removed upstream merged patch:
113-v5.21-platform-x86-pmc_atom-Add-Lex-3I380NX-industrial-PC-.patch

Manually rebased:
103-pcengines_apu6_platform.patch

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:36 +02:00
Pascal Coudurier
f23015b18e
x86: copy 5.15 patches to 6.1
Copy existing patches from 5.15 to 6.1

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:36 +02:00
Zoltan HERPAI
6bf8193b25 sunxi: add support for Bananapi P2 Zero
CPU:     Allwinner H2+ quad-core Cortex-A7 @ 1.2GHz
Memory:  512Mb DDR3
Storage: SDcard, 8GB eMMC
Network: 10/100M ethernet, optional PoE support, Ampak AP6212 wifi + BT
USB:     1x USB 2.0 OTG
Other:   40-pin expansion header, mini-HDMI

Flashing instructions:
  Standard sunxi SD card installation procedure - copy image to SD card,
  insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-18 18:15:21 +02:00
Felix Fietkau
93e147c9e6 hostapd: fix dynamically adding interfaces with 802.11ax support disabled in the build
Move an important code line outside of #ifdef CONFIG_IEEE80211AX

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-18 16:51:34 +02:00
Christian Marangi
c64a5d122f
sunxi: refresh kernel patches
Refresh kernel patches for sunxi target.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-09-18 13:44:50 +02:00
Felix Fietkau
ef8e2f66f5 mt76: update to the latest version
b5d13611d35e mt76: mt7915: fix monitor mode issues
bbbac7deee3d wifi: mt76: rename mt76_packet_id_init/flush to mt76_wcid_init/cleanup
f1e1e67d97d1 wifi: mt76: fix race condition related to checking tx queue fill status
b3f739a64e6b wifi: mt76: mt7996: add eht rx rate support
ca4917062f17 wifi: mt76: mt76x0: remove dead code in mt76x0_phy_get_target_power
325a0c493199 wifi: mt76: mt7996: fill txd by host driver
cd371fcc98d4 mt76: mt7996: sync with upstream
d71f8d1b172b wifi: mt76: use atomic iface iteration for pre-TBTT work
8d5ea32d4895 wifi: mt76: remove unused error path in mt76_connac_tx_complete_skb
01860c02c505 wifi: mt76: add DMA mapping error check in mt76_alloc_txwi()
62ddb6d46a97 wifi: mt76: connac: introduce helper for mt7925 chipset
0837f37e998b wifi: mt76: mt792x: support mt7925 chip init
899ff378082b wifi: mt76: connac: export functions for mt7925
c3858b5bf347 wifi: mt76: connac: add eht support for phy mode config
5df6b26a9fc5 wifi: mt76: connac: add eht support for tx power
a8081345c636 wifi: mt76: connac: add data field in struct tlv
9b38aebecf78 wifi: mt76: connac: add more unified command IDs
84984e6dc87d wifi: mt76: connac: add more unified event IDs
6fe92398c9ce wifi: mt76: mt7996: set correct wcid in txp
2cfe2fb0bb80 wifi: mt76: mt7996: fix beamform mcu cmd configuration
e512241bb5bb wifi: mt76: mt7996: fix beamformee ss subfield in EHT PHY cap
719a98f832c7 wifi: mt76: mt7996: fix wmm queue mapping
9723562f2a5b wifi: mt76: mt7996: fix rx rate report for CBW320-2
1bb5a6a54943 wifi: mt76: mt7996: fix TWT command format
751b054891f6 wifi: mt76: mt7996: only set vif teardown cmds at remove interface
fea1e10c7741 wifi: mt76: mt7996: support more options for mt7996_set_bitrate_mask()
d497ee8aa2f5 wifi: mt76: mt7996: support per-band LED control
8ccc84111141 wifi: mt76: Use PTR_ERR_OR_ZERO() to simplify code
161f70217edf wifi: mt76: mt7921e: Support MT7992 IP in Xiaomi Redmibook 15 Pro (2023)
7d25bfc3f0cc wifi: mt76: fix clang-specific fortify warnings
5971aa968401 wifi: mt76: connac: add MBSSID support for mt7996
5a47dd323be1 wifi: mt76: update beacon size limitation
d5b4b81dcc9e wifi: mt76: check sta rx control frame to multibss capability
af0e1f6dafb5 wifi: mt76: fix potential memory leak of beacon commands
65d91a833b01 wifi: mt76: get rid of false alamrs of tx emission issues
29411e52059f wifi: mt76: fix per-band IEEE80211_CONF_MONITOR flag comparison
4da62774038a wifi: mt76: check vif type before reporting cca and csa
4a85678fe089 wifi: mt76: mt7915: update mpdu density capability
791a45cffadf wifi: mt76: mt7915: fix beamforming availability check
08e1e6cb7d41 wifi: mt76: Drop unnecessary error check for debugfs_create_dir()
d1881b1b2bf6 wifi: mt76: move struct ieee80211_chanctx_conf up to struct mt76_vif
66d5694e1898 wifi: mt76: mt7921: fix the wrong rate pickup for the chanctx driver
9fc37b0ac546 wifi: mt76: mt7921: fix the wrong rate selected in fw for the chanctx driver
2afc7285f75d wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-18 12:51:53 +02:00
Felix Fietkau
13b24340d7 mac80211: backport upstream patch required for mt76 update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-18 12:50:45 +02:00
Chukun Pan
9889de3397
ipq40xx: add support for YYeTs LE1
Hardware Highlights:
SoC:	  Qualcomm IPQ4019 717 MHz
RAM:	  512M NT5CC256M16ER-EK
Flash:    32M SPI NOR MX25L25635F
WIFI1:    2.4 GHz 2T2R integrated
WIFI2:    5 GHz 2T2R integrated
Ethernet: QCA8075 (4x LAN, 1x WAN)
LEDS:     power, wlan2g, wlan5g, usb
USB:      1x 3.0
Button:   Reset

Installation:
  Upload factory.bin in stock firmware's upgrade
  page, and this will take a few minutes.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-09-18 12:20:04 +02:00
Chukun Pan
eb8ddf5d5c
ipq-wifi: update to version 2023-09-16
Contains following updates:

 * ipq8074: add Asus RT-AX89X BDF
 * ipq8074: update RegDB in new submitted BDF
 * ipq40xx: add YYeTs LE1 BDF
 * ipq8074: add Netgear WAX620
 * qca-wireless: ipq40xx: add BDFs for ZTE MF287
 * ipq8174: Add Linksys MX4200

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-09-18 12:20:01 +02:00
Andreas Böhler
a9cc3708e0
ipq40xx: fix image building for ZTE MF287 series
For the ZTE MF287 series, a special recovery image is built. The Makefile
worked fine on snapshot, but created corrupt images on the 23.05 images.
By using the appropriate variable, this should be fixed.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-18 11:49:37 +02:00
Zoltan HERPAI
12584395dc sunxi: add support for H616 SoC and Orangepi Zero 2
Specifications:

SoC:     Allwinner H616 @ 1.5 Ghz
DRAM:    1Gb LPDDR3
Power:   5V USB-C
Video:   HDMI (Type 2.0A - micro)
Network: 10/100/1000Mbps Ethernet (Realtek RTL8211F), AW859A BT+wifi
Storage: microSD / 2Mb SPI flash
USB:     1 USB2.0 Host
Debug    Serial UART

Flashing instructions:
  Standard sunxi SD card installation procedure - copy image to SD card,
  insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-18 00:08:19 +02:00
Max Qian
794349a28a ramips: RT1800: fix invalid octal number error
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.

Signed-off-by: Max Qian <public@maxqia.com>
2023-09-17 13:52:55 -07:00
Robert Marko
98bad1b4fc ipq40xx: 6.1: add missing secure QFPROM symbol
Kernel config for 6.1 on ipq40xx is missing the config for
CONFIG_NVMEM_QCOM_SEC_QFPROM which them makes the build stop with a prompt.

Symbol is there in 5.15 config but 6.1 config was based of a version that
does not yet have it set as it was introduced after the 6.1 PR.

So, disable CONFIG_NVMEM_QCOM_SEC_QFPROM to fix building on 6.1.

Fixes: 825cfa4e36 ("ipq40xx: 6.1: refresh kernel config")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 22:19:23 +02:00
Robert Marko
b50827fb10
ipq40xx: add 6.1 as testing kernel
Allow selecting 6.1 as the testing kernel.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:25 +02:00
Robert Marko
825cfa4e36
ipq40xx: 6.1: refresh kernel config
Refresh the kernel config via make kernel_menuconfig.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:24 +02:00
Robert Marko
cd9c721124
ipq40xx: 6.1: use latest DSA and ethernet patches
This pulls-in the latest version of qca8k based IPQ4019 driver as well as
the latest version of IPQESS that was sent upstream.

Both qca8k and IPQESS have been improved and cleaned up compared to current
version of patches.

PSGMII PHY mode and missing reset have been upstreamed and will be in
the kernel 6.6.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-09-17 21:00:24 +02:00
Robert Marko
4c010932a5
ipq40xx: 6.1: adapt and refresh patches
Adapt and refresh patches to apply.

DSA and ethernet driver patches are dropped as they will be replaced with
the latest version that was sent upstream.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:24 +02:00
Robert Marko
3d6d8bcd8f
ipq40xx: qca807x: adapt for 6.1
Kernel 6.1 has changed format of sfp_parse_support(), so lets adapt to
those changes so it works on newer kernels as well.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:23 +02:00
Robert Marko
bd242a42a6
ipq40xx: copy 5.15 patches and config to 6.1
Copy the 5.15 patches and config as a base for 6.1 support.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:23 +02:00
Robert Marko
70dfb696c0
ipq40xx: update ESS reset patch with pending upstream
Use the split version of ESS reset patch that was sent upstream.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:23 +02:00
Robert Marko
9bfbdfa778
ipq40xx: move DSA and ethernet driver to 5.15 specific directory
As a preparation to move to 6.1, we need to move the DSA and ethernet
drivers to a 5.15 specific directory as 6.1 will use the latest patchset
that was sent upstream which is too hard to backport to 5.15.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:22 +02:00
Matthijs Kooijman
d2ce3a61aa
ath79: fix packetloss on some WLR-7100
On some WLR-7100 routers, significant packet loss was observed. This is
fixed by configuring a delay on the GMAC0 RXD and RXDV lines.

The values used in this commit are copied from the values used by the
stock firmare (based on register dumping).

Out of four test routers, the problem was consistently observed on two.
It is unclear what the relevant difference is exactly (the two working
routers were v1 001 with AR1022 and v1 002 with AR9342, the two broken
routers were both v1 002 with AR1022). All PCB routing also seems
identical, so maybe there is some stray capacitance on some of these
that adds just enough delay or so...

With this change, the packet loss disappears on the broken routers,
without introducing new packet loss on the previously working routers.

Note that the PHY *also* has delays enabled (through
`qca,ar8327-initvals`) on both RX and TX lines, but apparently that is
not enough, or it is not effective (registers have been verified to be
written).

For detailed discussion of this issue and debug history, see
https://forum.openwrt.org/t/sitecom-wlr-7100-development-progress/79641

Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
2023-09-17 16:39:10 +02:00
Robert Marko
b33bfcf9fa
mac80211: ath11k: sync with ath-next
Synchronize the ath11k backports with the current ath-next tree.

All of the changes are various bugfixes, there is no new major feature.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 14:44:34 +02:00
Robert Marko
10eea40f7b
mac80211: ath11k: drop upstreamed patches
Commit ed3725e15a154ebebf44e0c34806c57525483f92
("wifi: ath11k: Fix qmi_msg_handler data structure initialization")
has been present upstream since 6.1.2 but it seems Quilt refreshed it
wrongly so it appeared like a completely different patch.

Commit 7c15430822e71e90203d87e6d0cfe83fa058b0dc
("wifi: ath11k: allow system suspend to survive ath11k")
has been present upstream since 6.1.16 but somehow quilt still happily
applied it.

So, drop both of them.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 14:44:30 +02:00
Zoltan HERPAI
863444f9cb sunxi: use kernel 6.1 as default
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-16 22:27:17 +02:00
Erik Karlsson
fdce970dbb procd: create /dev/fd symlink
This is needed for ksh/bash style process substitution such as
<(command) and >(command) which was introduced in ash as of busybox
version 1.34.0 to work.

Signed-off-by: Erik Karlsson <erik.karlsson@genexis.eu>
2023-09-16 20:48:34 +02:00
Roger Pueyo Centelles
8486c677b8 ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite)
This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as
hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one
with PoE in. The device was already supported by the ar71xx target.

Specifications:
 - SoC: Qualcomm Atheros QCA9533
 - Flash: 16 MB SPI NOR
 - RAM: 64 MB
 - Ethernet: 4x 10/100 Mbps LAN, 1x 10/100 Mbps WAN (PoE in)
 - LEDs: 5x Ethernet port activity (green), 1x user (green)
 - Buttons: 1x reset

 See https://mikrotik.com/product/RB750r2 for more details.

Not working:
 - Serial port (already not working in ar71xx)

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Only the
 "Internet" port will ask for an initramfs image. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2023-09-16 12:49:26 +02:00