qoriq has had kernel 6.1 as testing for 2 months now, so lets default to
it and drop 5.15 support.
Link: https://github.com/openwrt/openwrt/pull/15767
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, information from MikroTik hard_config is only available via
sysfs, meaning that we have to rely on userspace to for example setup MACs.
So, lets provide a basic NVMEM layout based driver to expose the same cells
as sysfs driver exposes.
Do note that the we dont extract the WLAN caldata and BDF-s at this point.
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/15665
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move the hard config tag ID-s to a separate header so they can be reused
by the NVMEM driver as well.
Link: https://github.com/openwrt/openwrt/pull/15665
Signed-off-by: Robert Marko <robimarko@gmail.com>
This driver has already been packed as a software package. There is
no need to build it into the kernel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch was causing buildbot issues when copying arm64 DT files since
bcm283x-rpi-csi1-2lane.dtsi and bcm283x-rpi-lan7515.dtsi were linked to
"../../../../arm/boot/dts/" instead of "../../../../arm/boot/dts/broadcom".
These files aren't needed, so let's remove them instead of fixing them.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15762
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently, of_get_ethdev_address() return is checked for any return error
code which means that trying to get the MAC from NVMEM cells that is backed
by MTD will fail if it was not probed before ag71xx.
So, lets check the return error code for EPROBE_DEFER and defer the ag71xx
probe in that case until the underlying NVMEM device is live.
Link: https://github.com/openwrt/openwrt/pull/15752
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since the introduction of out-of-band tagging, writing the outbound tag
had been completely broken: First, in place of a port mask containing
the port number, just the port number itself was set in the register
value. Just after that, the full port mask 0x3e (all 5 external ports)
was set unconditionally.
This remained unnoticed because the switch would then use the FDB to
decide where to send unicast packets; broadcast and multicast packets
were however sent to every port.
Fix the port tag computation and only use the full port mask as a
fallback for non-DSA mode, as it was done in the older driver patches
used on Linux 5.15.
Fixes: cd9c721124 ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Robert Marko <robimarko@gmail.com>
In my previous attempt to solve the PCI problems for the lantiq targets,
I did not pay attention to the fact that the original accesses to the
GPIO took place in RAW mode. As a result, the polarity defined in the
device trees (apart from the initial value) was irrelevant.
In addition, the expected name of the GPIO in the dts has changed due to
the upstream change and therefore no RESET is currently performed.
As discussed in [1] on the linux-mips mailing list, we will now adapt
the dts files accordingly instead of patching the driver:
- dts property will be renamed to "reset-gpios"
- Polarity is set to "GPIO_ACTIVE_LOW".
I have verified this with a TP-Link TD-W8980. The PCI device is now
recognized by the system.
[1] https://patchwork.kernel.org/project/linux-mips/patch/20240607090400.1816612-1-ms@dev.tdt.de/
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # Tested on AVM 7330 (ar9)
Link: https://github.com/openwrt/openwrt/pull/15731
Signed-off-by: Robert Marko <robimarko@gmail.com>
At some point RPi LEDs were renamed from led0/led1 to PWR/ACT.
This patch fixes this and also automatically detects the status_led without
relying on board_name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Currently, trying to upgrade on a MikroTik NAND device will force you to
use sysupgrade -n due to:
upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n).
upgrade: NAND images switched to yafut. If running older image, reinstall from initramfs.
So instead of having users manually set the new compat version lets do
what other targets do and set it for all NAND devices after good boot.
Link: https://github.com/openwrt/openwrt/pull/15754
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devices were already supported. I merely added missing entries to:
1. make them easier to locate in firmware selector
2. allow firmware upgrades to proceed without dire warnings
Sample dire warning contains:
upgrade: Device raspberrypi,model-zero-2-w not supported by this image
upgrade: Supported devices: rpi-3-b rpi-3-b-plus rpi-zero-2 \
raspberrypi,2-model-b-rev2 raspberrypi,3-model-b \
raspberrypi,3-model-b-plus raspberrypi,3-compute-module \
raspberrypi,compute-module-3 raspberrypi,model-zero-2
With this patch, the firmware upgrade proceeds normally.
Signed-off-by: Dave Brand <dbrand666@users.noreply.github.com>
Convert line endings from DOS to Unix using dos2unix.
Fixes: 2da2705a44 ("ramips: add support for WINSTARS WS-WN536P3")
Fixes: 5560791bbd ("ramips: add support for OpenFi 5Pro Travel Router")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol was removed upstream, but it was present on bcm27xx due to a
malformed upstream RPi patch.
Fixes: 8c405cdccc ("bcm27xx: add 6.6 kernel patches")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.34..rpi-6.1.y
Some patches needed rebasing and, as usual, the applied and reverted, wireless
drivers, Github workflows, READMEs and defconfigs patches were removed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is preparation for 6.6 kernel support. Copying files makes it easier to
track their git history.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Replace Silicon Labs patch with upstream version as they got merged in
kernel 6.3.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[ rework commit title and description, use better patch ]
Link: https://github.com/openwrt/openwrt/pull/15300
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Now that we can pass the desired compression via cmdline, pass ZSTD as the
desired compression algorithm for F2FS.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
F2FS requires the compression algorith to be passed as argument while
mounting, so lets do so for the misc partition.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In order to prolong the eMMC life and utilize ZSTD compression on Methode
devices, we must format the F2FS rootfs and misc partition with xattr and
compression support feature flags first.
This will only happen if partitions are broken currently, but later
commits will add support to convert existing boards to use compression.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Methode devices require mkfs.f2fs in order to format rootfs and misc
partitions if they have not already been formatted.
fdisk is required if partition table got broke so it can be regenerated.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
We would love to utilize ZSTD compression support in F2FS on the
Methode euroDPU so lets enable the required kernel support.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Refresh patches as line numbers changed with newer upstream version
since original backport PR was opened.
Fixes: a5c095c453 ("generic: 6.6: replace (broken) downstream patch with upstream solution")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Our downstream patch "net/core: add optional threading for backlog processing"
has been broken with the switch to Linux 6.6.
Replace it by backporting the now available upstream solution.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15592
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop config+patches for kernel 6.1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15713
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch the uml target to kernel 6.6.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15713
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
UML didn't have a subtarget defined.
While this compiled fine, the patch caused funny filenames
for the generated files to appear:
- "openwrt-uml--vmlinux"
- "openwrt-uml--squashfs.img"
- "openwrt-uml--ext4.img"
- ...
since "generic" is implied anyway, let's just set it.
Fixes: d997477775 ("treewide: remove implicit SUBTARGET")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15713
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop config+patches for kernel 6.1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15721
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch the apm821xx targets to kernel 6.6.
no complains received.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15721
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
gpio is deprecated. Found with dtc's -Wdeprecated_gpio_property
Used git grep -E $'\tgpio = <' to make the changes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15681
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions for SXK80
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/15732
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move nvmem-cells definitions to dts files for compatibility with other files
in which mt7628an_tplink_8m.dtsi is loaded, to prevent overwriting
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
