For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
As KEY_RESTART is already used for reset script (and there's no
KEY_REBOOT in Linux input events), use KEY_POWER2 for rebooting via new
reboot script with 5 second seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
As KEY_RESTART is already used for reset script (and there's no
KEY_REBOOT in Linux input events), use KEY_POWER2 for rebooting via new
reboot script with 5 second seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
ade00ca585a4 container: fix .dockerenv stat check
385b904b2f0a hotplug: improve error message during group ownership change
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add upstream patch from:
https://git.busybox.net/busybox/commit/?id=028c5aa18b5273c029f0278232d922ee1a164de6
The patch fixes a problem with an infinite loop causing 100% CPU usage
when running the following command /lib/preinit/10_indicate_preinit
without the CAP_NET_ADMIN capability (such as in Docker):
ip -4 address flush dev $pi_ifname
Signed-off-by: Mikael Magnusson <mikma@users.sourceforge.net>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [refresh patch]
This patch fixes following missing bits:
- add missing 'compatible' property on firmware partition
- set vendor partition 'userconfig' read-only
Fixes: 30dcbc741d ("ath79: add support for EnGenius ECB1750")
Signed-off-by: Sven Friedmann <sf.openwrt@okay.ms>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n
5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO
Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.
UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX
See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.
Tested sysupgrade + factory flash from WD Emergency Recovery
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Don't set the default firewall zone to wan if not specified to keep the
behavior aligned with other tunnel protocols like gre and 6rd.
If the interface zone is not specified try to get it from the firewall config
when constructing the procd firewall rule.
While at it only add procd inbound/outbound firewall rules if a zone is specified.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Don't set the default firewall zone to wan if not specified to keep the
behavior aligned with other tunnel protocols like gre and 6rd.
If the interface zone is not specified try to get it from the firewall config
when constructing the procd firewall rule.
While at it only add a procd inbound firewall rule if a zone is specified.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* Feature: Add support for 200Gbps (50Gbps per lane) link mode
* Feature: simplify handling of PHY tunable downshift
* Feature: add support for PHY tunable Fast Link Down
* Feature: add PHY Fast Link Down tunable to man page
* Feature: Add a 'start N' option when specifying the Rx flow hash indirection table.
* Feature: Add bash-completion script
* Feature: add 10000baseR_FEC link mode name
* Fix: qsfp: fix special value comparison
* Feature: move option parsing related code into function
* Feature: move cmdline_coalesce out of do_scoalesce
* Feature: introduce new ioctl for per-queue settings
* Feature: support per-queue sub command --show-coalesce
* Feature: support per-queue sub command --coalesce
* Fix: fix up dump_coalesce output to match actual option names
* Feature: fec: add pretty dump
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This makes sysupgrade work on the D-Link DIR-685 after
initial factory install.
We create the platform.sh script to support sysupgrade
on more targets as we move on with sysupgrade support.
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[cleanup in platform.sh, removed superfluous SUPPORTED_DEVICES]
Lua's LNUM patch currently doesn't parse properly certain numbers as
it's visible from the following simple tests.
On x86_64 host (stock Lua 5.1.5, expected output):
$ /usr/bin/lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
2147483648
8796093022208
4294967296
On x86_64 host:
$ staging_dir/hostpkg/bin/lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
-2147483648
0
0
On x86_64 target:
$ lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
-2147483648
0
0
On ath79 target:
$ lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
-2147483648
8796093022208
4294967296
It's caused by two issues fixed in this patch, first issue is caused by
unhadled strtoul overflow and second one is caused by the cast of
unsigned to signed Lua integer when parsing from hex literal.
Run tested on:
* Zidoo Z9S with RTD1296 CPU (aarch64_cortex-a53)
* qemu/x86_64
* qemu/armvirt_64
* ath79
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
[commit subject/message touches, fixed From to match SOB, fixed another
unhandled case in luaO_str2i, host Lua, package bump]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 0111b86f1d as it
breaks on Linux distributions without ed support
./fix-libmath_h: line 1: ed: command not found
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
When running OpenWrt inside an LXC container no shell is opend as LXC
defaults to a virtual /dev/console.
This patch allows to enter a shell after starting the container via
`lxc-start`, without it is only posible to access a shell on tty1 via
`lxc-console`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The vendor firmware only uses two mac addresses, the mac address on the
label and the label + 1. While checking multiple devices, all labels have
even mac addresses. Concluding only 2 address are assigned to a device.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The GL.iNet AR750S USB and microSD port is currently not working out of
the box. GPIO 7 is used to control the power of the USB port. Add GPIO
7 as a fixed-regulator for the port. Also add &usb1 to DTS to get the
microSD port to work.
Signed-off-by: Alexander Wördekemper <alexwoerde@web.de>
This patch fixes `sysupgrade -n` when flashed with rootfs of the same
size as currently running, so the rootfs_data wouldn't get destroyed and
thus survive reboot. So let's fix it by always cleaning up the content
of the rootfs_data during sysupgrade.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ar71xx uses `archer-c7-v5` for led prefix, but ath79 sticks to more
generic `tplink` as the DTS is reused by more boards, so we need to
perform migrations of the LED names during upgrade.
Cc: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which are using
ar8xxx switch LEDs trigger, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to emac0, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to mdio0 bus, as the same value was set for
built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin
switch").
Some measurements performed on TP-Link Archer C7-v5:
mib-type=0, mib-poll-interval=500ms (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.93 0.00 0.00 1.93 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
mib-type=0, mib-poll-interval=2s (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.14 0.00 0.00 1.14 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
So it seems like we get 4x faster LED refresh rate for additional 0.8%
CPU load.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" has
added mib_poll_interval global config option and commit "generic:
ar8216: group MIB counters and use two basic ones only by default" has
added mib_type config option.
So this patch adds ucidef_set_ar8xxx_switch_mib helper function which
would allow configuration of the above mentioned new switch config
options.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" has added
mib_poll_interval global config option and commit "generic: ar8216: group
MIB counters and use two basic ones only by default" has added mib_type
config option.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There are too many MIB counters that almost nobody needs since commit
d6366ce366 ("generic: ar8216: mib_work_func: read all port mibs
everytime").
In the worker function to poll MIB data, it deals with all ports instead
of only one port every time, which introduces too many mdio operations
that it becomes a heavy CPU load even on not-emulated MDIO bus.
This commit groups MIB counters and enable only TxBytes and RxGoodBytes
by default (both of which are necessary to get swconfig led working.)
and adds an swconfig attribute to allow enabling all counters if users
need them.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This allows specifying interval of polling MIB counters from userspace
and allow completely turning off MIB counter support by setting
mib_poll_interval to 0.
Since MIB counter polling is a heavy CPU load for GPIO emulated MDIO
bus, disable this behavior by default. Those who wants to use swconfig
LEDs can enable them with qca,mib-poll-interval dts property or with
swconfig command.
Fixes: FS#2230 ("kworker spikes 100% cpu every 2 second.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This adds the host staging directory to the include path to make it use
the zlib.h files from the staging include directory and also link
against the zlib version from the staging directory.
This fixes a compile problem when the zlib header were not installed on
the build host.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[picked from openwrt-18.06]
The SD-Card polling is now implemented by default in the
fs-tools block-mount utility package. It might not be as
fast as the current detection method since the polling
time is 2 Seconds, but it's much less of an hack.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
c9d9dbf pppoe: Custom host-uniq tag
44012ae plugins/rp-pppoe: Fix compile errors
Refresh patches
Drop 520-uniq patch as upstream accepted
Drop 150-debug_compile_fix patch as fixed upstream
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This patch converts the Range Extender to use the
interrupt-driven gpio-keys driver over the polled variant.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts the WNDR3700 to use the interrupt-driven
gpio-keys driver over the polled variant.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All other QCA9563 devices already use this identifier for
the exact SoC. Not that this matters much since as upstream
states in Documentation/devicetree/usage-model.txt:
"First and foremost, the kernel will use data in the DT to
identify the specific machine. In a perfect world, the
specific platform shouldn't matter to the kernel because all
platform details would be described perfectly by the device
tree in a consistent and reliable manner.
[...]
In the majority of cases, the machine identity is irrelevant,
and the kernel will instead select setup code based on the
machine's core CPU or SoC."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.
Internally eth0 is connected to the Broadcom CPU.
Router section - Specification:
CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB
Known issues:
DSL not working (eth0) (WIP)
UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC
J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX
The following instructions require a connection to the J2 UART header.
Flash instruction under U-Boot, using UART
------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
bootm 0x81000000
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
4. Double check the .mod file size. It must be 7995392 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
This commit adds the partition layout used by the TP-Link Archer D50
and probably by the TP-Link Archer D7 to mktplinkfw2.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
