Make sure the compatible string in DTS matches the now v1/v2
differentiated board name in target/linux/mediatek/image/mt7622.mk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit be555b9dd8)
Make use of minor sector size (4k) on supported SPI-NOR flash chips.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 51f4c84178)
As of upstream Linux commit 0fe1e96fef0a ("powerpc/pci: Prefer PCI
domain assignment via DT 'linux,pci-domain' and alias"), the PCIe
domain address is no longer numbered by the lowest 16 bits of the PCI
register address after a fallthrough. Instead of the fallthrough, the
enumeration process accepts the alias ID (as determined by
`of_alias_scan()`). This causes e.g.:
9000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11)
9000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ...
to become
0000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11)
0000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ...
... which then causes the sysfs path of the netdev to change,
invalidating the `wifi_device.path`s enumerated in
`/etc/config/wireless`.
One other solution might be to migrate the uci configuration, as was
done for mvebu in commit 0bd5aa89fc ("mvebu: Migrate uci config to
new PCIe path"). However, there are concerns that the sysfs path will
change once again once some upstream patches[^2][^3] are merged and
backported (and `CONFIG_PPC_PCI_BUS_NUM_DOMAIN_DEPENDENT` is enabled).
Instead, remove the aliases and allow the fallthrough to continue for
now. We will provide a migration in a later release.
This was first reported as a Github issue[^1].
[^1]: https://github.com/openwrt/openwrt/issues/10530
[^2]: https://lore.kernel.org/linuxppc-dev/20220706104308.5390-1-pali@kernel.org/t/#u
[^3]: https://lore.kernel.org/linuxppc-dev/20220706101043.4867-1-pali@kernel.org/Fixes: #10530
Tested-by: Martin Kennedy <hurricos@gmail.com>
[Tested on the Aerohive HiveAP 330 and Extreme Networks WS-AP3825i]
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(cherry picked from commit 7f4b4c29f3)
Commit 0b7c66c ("at91bootstrap: add sama5d27_som1_eksd1_uboot as
default defconfig") changed default booting media for sama5d27_som1_ek
board w/o any reason. Changed it back to sdmmc0 as it is for all the
other Microchip supported distributions for this board (Buildroot,
Yocto Project). The initial commit cannot be cleanly reverted.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
(cherry picked from commit e9f12931e6)
Commit adc69fe (""uboot-at91: changed som1 ek default defconfigs")
changed the booting media to sdmmc1 as default booting w/o any reason.
The Microchip releases for the rest of supported distributions (Buildroot,
Yocto Project) uses sdmmc0 as default booting media for this board.
Thus change it back to sdmmc0. With this remove references to sdmmc1
config. The initial commit cannot be cleanly reverted.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
(cherry picked from commit 9a49788008)
platform_nand_pre_upgrade() is gone since commit 790692dde2
("base-files: drop support for the platform_nand_pre_upgrade()").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a6dc0f680d)
This patch defines the two switch LED to bring them under user control.
Fixes: 158a5af801 ("ramips: improve YunCore AX820 LEDs")
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[rmilecki: leave "label"s in place]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7bee10a7d2)
Specifications:
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: 2x 128MB Nanya NT5TU64M16HG
- FLASH: 64MB - SPANSION FL512SAIFG1
- LAN: Atheros AR8035-A (RGMII GbE with PoE+ IN)
- WLAN2: Qualcomm Atheros QCA9557 2x2 2T2R
- WLAN5: Qualcomm Atheros QCA9882-BR4A 2x2 2T2R
- SERIAL: UART pins at J10 (115200 8n1)
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
- LEDs: Power (Green/Amber)
WiFi 5 (Green)
WiFi 2 (Green)
- BTN: Reset
Installation:
1. Download the OpenWrt initramfs-image.
Place it into a TFTP server root directory and rename it to 1D01A8C0.img
Configure the TFTP server to listen at 192.168.1.66/24.
2. Connect the TFTP server to the access point.
3. Connect to the serial console of the access point.
Attach power and interrupt the boot procedure when prompted.
Credentials are admin / new2day
4. Configure U-Boot for booting OpenWrt from ram and flash:
$ setenv boot_openwrt 'setenv bootargs; bootm 0xa1280000'
$ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
tftpboot 0x89000000 1D01A8C0.img; bootm'
$ setenv bootcmd 'run boot_openwrt'
$ saveenv
5. Load OpenWrt into memory:
$ run ramboot_openwrt
6. Transfer the OpenWrt sysupgrade image to the device.
Write the image to flash using sysupgrade:
$ sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: Albin Hellström <albin.hellstrom@gmail.com>
[rename vendor - minor style fixes - update commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f8c87aa2d2)
Refresh all patches on top of kernel 5.10.138.
The following patches were applied upstream:
bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch
bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch
bcm27xx/patches-5.10/950-0346-drm-vc4-A-present-but-empty-dmas-disables-audio.patch
bcm27xx/patches-5.10/950-0354-drm-vc4-Add-the-2711-HVS-as-a-suitable-DMA-node.patch
bcm27xx/patches-5.10/950-0413-drm-vc4-hdmi-Don-t-access-the-connector-state-in-res.patch
bcm27xx/patches-5.10/950-0505-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch
bcm27xx/patches-5.10/950-0512-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch
bcm27xx/patches-5.10/950-0560-drm-vc4-drv-Remove-the-DSI-pointer-in-vc4_drv.patch
bcm27xx/patches-5.10/950-0561-drm-vc4-dsi-Use-snprintf-for-the-PHY-clocks-instead-.patch
bcm27xx/patches-5.10/950-0562-drm-vc4-dsi-Introduce-a-variant-structure.patch
bcm27xx/patches-5.10/950-0565-drm-vc4-Correct-pixel-order-for-DSI0.patch
bcm27xx/patches-5.10/950-0566-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch
bcm27xx/patches-5.10/950-0567-drm-vc4-Fix-dsi0-interrupt-support.patch
bcm27xx/patches-5.10/950-0568-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch
bcm27xx/patches-5.10/950-0647-drm-vc4-Fix-timings-for-interlaced-modes.patch
bcm27xx/patches-5.10/950-0695-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch
Upstream sets the pixel clock to 340MHz now, do not set it to 600MHz any more.
bcm27xx/patches-5.10/950-0576-drm-vc4-hdmi-Raise-the-maximum-clock-rate.patch
Fixes: 89956c6532 ("kernel: bump 5.10 to 5.10.138")
Fixes: 4209c33ae2 ("kernel: bump 5.10 to 5.10.137")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 5a81e00063 as it was
backported upstream in commit a1e238690916 ("arm64: dts: mt7622: fix
BPI-R64 WPS button").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Removed following upstreamed patch:
* bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch
All other patches automagically rebased.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit d1163fd13f)
Change switch port labels to ethblack & ethblue.
Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins.
Add the external phy with ethyellow label on the GB-PC2 devicetree.
Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function.
Enable ICPlus PHY driver for IP1001 which GB-PC2 has got.
Update interface name and change netdev function.
Enable lzma compression to make up for the increased size of the kernel.
Make spi flash bindings on par with mainline Linux to fix read errors.
Tested on GB-PC2 by Petr.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 4807bd6a00)
Add missing scaling_available_frequencies sysfs entry for dedicated
cpufreq driver.
This sysfs entry is not standard and each cpufreq driver needs to
provide it and declare it in the cpufreq driver struct attr.
Fixes: 5dbbefcbcc ("ipq806x: introduce dedicated krait cpufreq")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[ fix conflict by dropping 5.15 patch not present in openwrt-22.03 ]
(cherry picked from commit d6994c53cd)
This commit resolves#10062. Adds decryption of the Arcadyan WG4xx223
configuration partition (board_data)to get base MAC address from it.
As a result, after this change the hack with saving MAC addressees to
u-boot-env before installation of OpenWrt is no longer necessary.
This is necessary for the following devices:
- Beeline Smartbox Flash (Arcadyan WG443223)
- MTS WG430223 (Arcadyan WG430223)
Example:
+----------------+-------------------+------------------------+
| | MTS WG430223 | Beeline Smartbox Flash |
+----------------+-------------------+------------------------+
| base mac (mtd) | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 |
| label | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:09 |
| LAN | A4:xx:xx:51:xx:F6 | 30:xx:xx:51:xx:09 |
| WAN | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 |
| WLAN_2g | A4:xx:xx:51:xx:F5 | 30:xx:xx:51:xx:07 |
| WLAN_5g | A6:xx:xx:21:xx:F5 | 32:xx:xx:41:xx:07 |
+----------------+-------------------+------------------------+
Collected statistic shows that the 2-4th bits of the 7th byte of the
WLAN_5g MAC are the constant (see #10062 for more details):
- Beeline Smartbox Flash - 100
- MTS WG430223 - 010
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit a6b0d08060)
This commit:
1. Renames beeline-trx recipe in mt7621.mk to arcadyan-trx. The recipe
is necessary for:
- MTS WG430223 (Arcadyan WG430223)
- Beeline Smartbox Flash (Arcadyan WG443223)
2. Allows specify custom trx magic which is different for the routers
mentined above.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 109c503bee)
[fix merging conflict in mt7621.mk]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
This commit moves common properties for the boards below to a new dtsi:
Beeline Smartbox Flash (Arcadyan WG443223)
MTS WG430223 (Arcadyan WG430223)
The boards are almost the same. Here is the differences:
+------+----------+----------+
| | WG430223 | WG443223 |
+------+----------+----------+
| RAM | 128 | 256 |
+------+----------+----------+
| USB | - | 1x3.0 |
+------+----------+----------+
| LEDS | RG | RGB |
+------+----------+----------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 5b59137a16)
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223
Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
7. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | A4:xx:xx:51:xx:F4 | No MACs was |
| LAN | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN | A4:xx:xx:51:xx:F4 | [1] |
| WLAN_2g | A4:xx:xx:51:xx:F5 | |
| WLAN_5g | A6:xx:xx:21:xx:F5 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
"Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
MTS WG430223 devices even within the same broadcast domain.
Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset | | Description |
+==============+===============+========================================+
| 0x0 | 31 52 48 53 | TRX magic "1RHS" |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 498c15376b)
Specifications:
- Device: ASUS RT-AX53U
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 3 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- Ports: USB 3.0
- LEDs: 1x POWER (blue, configurable)
3x LAN (blue, configurable)
1x WAN (blue, configurable)
1x USB (blue, not configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
(replaced led label, added key-* prefix to buttons, added note about
BBT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 8c00fd9b45)
It backports this patch series, which is currently on review:
https://lore.kernel.org/linux-leds/20220704105955.15474-1-kabel@kernel.org/T/#rb89a4ca5a836f17bdcc53d65549e0b1779bb6a18
It allows being able to configure LEDs in userspace.
This fixes issue described in Turris Build repository
https://gitlab.nic.cz/turris/os/build/-/issues/354
It happens in OpenWrt as well.
- Before
```
root@turris:/# ls /sys/class/leds/
ath10k-phy0 ath9k-phy1 mmc0::
```
-After
```
root@turris:/# ls /sys/class/leds/
ath10k-phy0 rgb:indicator-2 rgb:lan-3 rgb:wlan-1
ath9k-phy1 rgb:lan-0 rgb:lan-4 rgb:wlan-2
mmc0:: rgb:lan-1 rgb:power rgb:wlan-3
rgb:indicator-1 rgb:lan-2 rgb:wan
```
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 049368b936)
In subtarget p2020, there wasn't enabled nand support, and because of
that there weren't available tools from mtd-utils package, which has
utilities for NAND flash memory even though reference board, which
is the only currently supported device in p2020 subtarget has NAND [1].
All subtargets in mpc85xx has already enabled nand support, let's do it
globally.
[1] https://www.nxp.com/design/qoriq-developer-resources/p2020-reference-design-board:P2020RDB
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 6006f73383)
Add support for LEDs of the CZ.NIC Turris Omnia using the upstream
driver.
There is no generic way to control the LEDs in UCI manner, however
the kernel module is the first step to actually use the RGB LEDs in
custom logic.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
(removed DMARC notice, added driver to Turris Omnia, moved module
recipe to target/linux/mvebu/modules.mk)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit f8fa38c13f)
Reviewed-by: Robert Marko <robimarko@gmail.com>
Commit 21f460a5db ("ath25: fix duplicate LZMA compression") changed
the way kernel images are generated, affecting initramfs images instead.
Initramfs images were previously ELF images, and by mistake this change
caused the raw kernel image to be used as a source. This caused them to
be non-loadable by bootloaders.
Restore the previous KERNEL_INITRAMFS recipe and adjust
KERNEL_INITRAMFS_NAME to point at the correct source artifact.
While at that, adjust KERNEL_INITRAMFS_SUFFIX to -kernel.elf,
so it matches the suffix of non-initramfs kernel artifact.
Fixes: 21f460a5db ("ath25: fix duplicate LZMA compression")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 9f5cbb6e8b)
Commit 21f460a5db ("ath25: fix duplicate LZMA compression"), when
attempting to restore ELF artifact generation, copiedover the raw
kernel image twice. Because of that, the .elf artifact was actually a
duplicate of raw image.
Fix that by copying over .elf suffixed kernel image instead.
Fixes: 21f460a5db ("ath25: fix duplicate LZMA compression")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 611291383a)
This backports some patches from kernel 5.15 to fix issues with
flowtable offloading in kernel 5.10. OpenWrt backports most of the
patches related to flowtable offloading from kernel 5.15 already, but we
are missing some of the extra fixes.
This fixes some connection tracking problems when a flow gets removed
from the offload and added to the normal SW path again.
The patch 614-v5.18-netfilter-flowtable-fix-TCP-flow-teardown.patch was
extended manually with the nf_conntrack_tcp_established() function.
All changes are already included in kernel 5.15.
Fixes: #8776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 96ef2dabce)
The nft NAT packages for IPv4 and IPv6 were merged into the common
packages with kernel 5.1. The kmod-nft-nat6 package was empty in our
build, remove it.
Multiple kernel configuration options were also removed, remove them
from our generic kernel configuration too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b75425370d)
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).
Backport upstream commit for its effect on the number of connections per
hashtable bucket.
Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit 15fbb91666)
The international version of Mi Router 4A 100M is physically
identical to the non-international one, but appears to be
using a different partitioning scheme with the "overlay"
partition being 2MiB in size instead of 1MiB. This means
the following "firmware" partition starts at a different
address and the DTS needs to be adjusted for the firmware
to work.
Signed-off-by: Nita Vesa <werecatf@outlook.com>
(cherry picked from commit 1a8c74da70)
Signed-off-by: Tom Herbers <freifunk@tomherbers.de>
As the symbol RTL930x shows, the bool enables the RTL930x platform, not
the RTL839x one.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
(slightly changed commit subject)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 943905b0b6)
|Warning: trailing whitespace in line 66 of drivers/mtd/parsers/Kconfig
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit d6801e0d3f)
The Lex 3I380NX industrial PC has 4 ethernet controllers on board
which need pmc_plt_clk0 - 3 to function, add it to the critclk_systems
DMI table, so that drivers/clk/x86/clk-pmc-atom.c will mark the clocks
as CLK_CRITICAL and they will not get turned off.
This commit is nearly redundant to 3d0818f5eba8 ("platform/x86:
pmc_atom: Add Lex 3I380D industrial PC to critclk_systems DMI table")
but for the 3I380NX device.
The original vendor firmware is only available using the WaybackMachine:
http://www.lex.com.tw/products/3I380NX.html
Signed-off-by: Michael Schöne <michael.schoene@rhebo.com>
Signed-off-by: Paul Spooren <paul.spooren@rhebo.com>
(Hans broader version for more Lex Baytrail systems)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 8019410f56)
There are forum reports that 2 LAN ports are still not working,
the phy-mode settings are adjusted to fix the problem.
Fixes: #10371
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
(cherry picked from commit 8756a04787)
All patches automatically rebased.
The following patch was replaced by a similar version upstream:
bcm27xx/patches-5.10/950-0036-tty-amba-pl011-Add-un-throttle-support.patch
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 7d3c0928de)
Using the BOARD_NAME variable results for both er and erlite devices to
identify themselfs as `er` and `erlite` (via `ubus call system board`).
This is problematic when devices search for firmware upgrades since the
OpenWrt profile is actually called `ubnt_edgerouter` and
`ubnt_edgerouter-lite`.
By adding the `SUPPORTED_DEVICE` a mapping is created to point devices
called `er` or `erlite` to the corresponding profile.
FIXES: https://github.com/openwrt/asu/issues/348
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 2a07270180)
