Revert the changes I applied to aa5014dd1a ("ramips: mt7620n: enable
port 4 as EPHY by default").
The driver expects a node mdio-bus to be present, regardless of the
actual node status. If the node is missing the driver fails to load with
mtk_soc_eth 10100000.ethernet: no mdio-bus child node found
Disable port4 by default again. If the port is enabled but not present, a
"invalid port id 4" warning is shown during boot.
Fixes: FS#1428
Signed-off-by: Mathias Kresin <dev@kresin.me>
In kernels 4.0 and older that header file was located in some subdir of
arch/mips/include. Target brcm47xx supports kernels 4.4 and 4.9 only so
that code isn't needed anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If CONFIG_GPIO_SYSFS=n, compilation fails with
drivers/built-in.o: In function `gpio_export_with_name':
include/asm-generic/gpio.h:128: undefined reference to `__gpiod_export'
This is because the stub in that case has the wrong name,
_gpiod_export() - note the missing underscore (_) at the
start.
Fix the stub, and add the correct prototype for the real
implementation.
Signed-off-by: André Draszik <git@andred.net>
Optimize the compiler output for larger cache blast cases that are
common for DMA-based networking.
On ar71xx, I measured a routing throughput increase of ~8%
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts the changes needed for the upstream b53 DSA switch driver
to use the OpenWrt b43 swconfig switch driver instead.
Tested-by: TheWerthFam <thewerthfam@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit introduces new subtarget for Marvell EBU Armada Cortex A53
processor based devices.
The first device is Globalscale ESPRESSObin. Some hardware specs:
SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53
processor up to 1.2GHz
RAM: 512MB, 1GB or 2GB DDR3
Storage: SATA interface
µSD card slot with footprint for an optional 4GB EMMC
4MB SPI NOR flash for bootloader
Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports
Connectors: USB 3.0
USB 2.0
µUSB port connected to PL2303SA (USB to serial bridge
controller) for UART access
Expansion: 2x 46-pin GPIO headers for accessories and shields with
I2C, GPIOs, PWM, UART, SPI, MMC, etc
MiniPCIe slot
Misc: Reset button, JTAG interface
Currently booting only from µSD card is supported.
The boards depending on date of dispatch can come with various U-Boot
versions. For the newest version 2017.03-armada-17.10 no manual
intervention should be needed to boot OpenWrt image. For the older ones
it's necessary to modify default U-Boot environment:
1. Interrupt boot process to run U-Boot command line,
2. Run following commands:
(for version 2017.03-armada-17.06 and 2017.03-armada-17.08)
setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
(for version 2015.01-armada-17.02 and 2015.01-armada-17.04)
setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait"
setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}"
saveenv
3. Poweroff, insert SD card with OpenWrt image, boot and enjoy.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.
An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.
Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.
Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.
Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem
Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv
Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.
Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
As at this commit, DSA is not enabled in the kernel config for mvebu, so these
nodes have been ignored. In preparation for the first mvebu board using DSA,
disable these nodes for existing boards to avoid issues.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Only register the chipidea usb device if the strapping option indicates
device mode. If not, use the regular ehci platform driver.
Add qca955x device mode support, tested on 8devices Rambutan.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In addition to removing redundant code, this fixes various issues in
IB-generated images that have been fixed in prepare_rootfs before,
including better handling of CONFIG_CLEAN_IPKG and enabling of initscripts
from FILES.
We also reuse the opkg macro and remove --force-... flags that have been
removed from rootfs.mk as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The Lantiq XRX200 aka VR9 doesn't have an asc0. Instead,
there is an USIF module which can either be an UART or a
SPI Controller.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
According to the datasheet the mt7620n have a fixed switch configuration
with 5 ephy (10/100) port. No RGMII configuration is possible.
Drop the mdio node as well. Without RGMII, the mdio node doesn't make any
sense
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[drop mdio node, enable port4 by default]
Signed-off-by: Mathias Kresin <dev@kresin.me>
In some boards port 4 of mt7620 switch is powered down in bootloader
configuration as lan/wan package leak mitigation.
Reset ephy port 4 to default settings to power up the port.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[clarify issue in commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.
* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).
Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.
Compile-tested on: ar71xx & oxnas.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
This patch bumps the 4.14 kernel to .23.
- Refreshed patches.
- Deleted bcm53xx/patches-4.14/089-PCI-iproc-Fix-NULL-pointer-dereference-for-BCMA.patch. Has been accepted upstream.
- Deleted generic/pending-4.14/821-usb-Remove-annoying-warning-about-bogus-URB.patch. The upstream URB code was changed,
the patch no longer applies. I discussed this with the patch author and removed it for now, we'll see how it goes.
Compile-tested on: ramips/mt7621, x86/64
Run-tested on: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Remove dependency on net-tools, replacing calls to ifconfig with iproute
equivalent, in functions changing interface MAC addresses.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Cosmetic name change of ClearFog sysupgrade script and its functions to
more generic sdcard. This way it won't be confusing for other future
device additions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Unify boot.scr generation so Makefile for device image generation won't
grow without a reason. Also make boot-scr step optional.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Previously the partition signature was assigned from provided type. Now
both are corrected wherein signature is always generated from
SOURCE_DATE_EPOCH. With that the root file system can be identified
by PARTUUID string, without relying on static declaration of device node.
This commit also does some cosmetics, removing trailing whitespace and
replacing spaces with tab.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The IMAGE_NAME redefinition causes overwriting of generated SD card
image when multiple root file system types are selected. In result only
single SD card image is generated. This commit fixes this behaviour.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
U-Boot already knows where it found the boot.scr, and
figuring out the partition UUID becomes trivial at this point.
This change allows booting OpenWrt from whatever storage it has been
flashed to: SD card, eMMC, USB disk or SATA disk.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
[replace lede with openwrt, redact commit message]
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The Armada XP uses a Marvell PJ4Bv7 Processor for which already one
workaround for an errata is activated.
The Armada 285 uses a Cortex A9 r4p1 for which the Linux kernel provides
a workaround for ERRATA_764369, activate this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With this change, the timestamp variable is only used in ag71xx_check_dma_stuck. Small tx speedup.
Based on a Qualcomm commit. ag->timestamp = jiffies was not replaced with netif_trans_update(dev) because of this quote:
It should be noted that after this series several instances
of netif_trans_update() are useless (if they occur in
.ndo_start_xmit and driver doesn't set LLTX flag -- stack already
did an update).
From: http://lists.openwall.net/netdev/2016/05/03/87
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Upstream handling of MIPS CPU IRQs is rather hackish and the interrupts
are being enabled unconditionally in various places because of legacy
code.
Performance counter events are routed both through the GIC and through
legacy CPU IRQ7 events, causing spurious interrupts.
Fix this by disabling IRQ7 when trying to access the performance counter
IRQ.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Looking for a wrong LED file name was stopping this code from find any
LED. This affects devices with only a red/amber power LED.
Fixes: 3aaee1ba02 ("bcm53xx: failsafe support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When CGROUPS is enabled the new option CONFIG_CGROUP_NET_CLASSID is
selectable and not handled.
Add this option to the 4.14 kernel configuration.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
As each mvebu device only uses one of the firmwares provided by mwlwifi
package, it makes sense to put them in separate packages and only install
the one that is needed.
Current mwlwifi version's firmware sizes and usages by devices:
88W8864.bin 118776 caiman, mamba, cobra, shelby
88W8897.bin 489932 (none)
88W8964.bin 449420 rango
Changes by this commit:
* indicate in title that mwlwifi also is driver for 88W8897 and 88W8964
* remove mwlwifi package's firmware installation rules
* add 3 new individual firmware packages (all depends on kmod-mwlwifi):
- mwlwifi-firmware-88w8864
- mwlwifi-firmware-88w8897
- mwlwifi-firmware-88w8964
* add firmware package to mvebu devices' DEVICE_PACKAGES accordingly
Signed-off-by: Johnny S. Lee <_@jsl.io>
[Add the used FW files to the PACKAGES of default image]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
