Commit Graph

50519 Commits

Author SHA1 Message Date
Rafał Miłecki
741164fdac bcm53xx: fix Linksys EA9500 partitions
Use proper DT binding.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit f8669c174e)
2021-04-08 12:49:01 +02:00
Vivek Unune
50a25d4394 bcm53xx: backport Linksys Panamera (EA9500) patches
These patches have been already accepted.

302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch had to
be updated.

[rmilecki: use actual upstream accepted patches
           replace v5.10 with v5.11 to match actual upstream kernel
           recover dropped part of the pinctrl compatible patch
           update filenames
           refresh patches]

Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 39ed2265dd)
2021-04-08 12:49:01 +02:00
Rafał Miłecki
0a98a33e09 kernel: backport 5.13 mtd partitioning changes
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 3fd0a4222b)
2021-04-08 11:25:41 +02:00
Felix Fietkau
64ddac2c1c mac80211: merge a few pending tx related fixes
Improve performance and fix potential mgmt tx hangs/warnings

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 571aedbc6c)
2021-04-04 11:39:51 +02:00
Felix Fietkau
69794908b6 mac80211: backport upstream patches for driver disconnect
Needed for an mt76 update

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 5dc5015072)
2021-04-04 11:39:51 +02:00
Felix Fietkau
95b838f75b build: use -nostdinc and -isystem in NOSTDINC_FLAGS for out-of-tree kernel modules
This resolves issues uncovered by musl updates

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 9ac47ee469)
2021-04-04 11:39:51 +02:00
David Bauer
6090337679 generic: add missing symbols
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 55ed4bf6d7)
2021-04-03 17:06:39 +02:00
INAGAKI Hiroshi
6f42758000 ath79: fix label_mac for NEC Aterm WG1200CR
On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label
on the case, not LAN.
This patch fixes this issue.

Fixes: 50fdc0374b ("ath79: provide label MAC address")

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit e2331fb549)
2021-04-02 16:04:47 +02:00
Shiji Yang
b8eb602934 ramips: correct switch config of Youku yk1
There are only two lan ports and one wan port on Youku yk1

Fixes: e9baf8265b ("ramips: add support for Youku YK1")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b88d2850c6)
2021-04-02 16:04:00 +02:00
Donald Hoskins
b2c9a8741f libunwind: Add MIPS64 dep check
libunwind dependency check does not allow for MIPS64 arch.  Add MIPS64 awareness.

libunwind seems to support MIPS64 without issues, it was limited by the dep arch
check in the Makefile.

Used to compile Suricata6/Rust locally without issue.

Signed-off-by: Donald Hoskins <grommish@gmail.com>
(cherry picked from commit ea6d4bdde2)
2021-03-29 22:26:27 +02:00
Robert Marko
da7ef7f414 ipq40xx: net: phy: qca807x: fix GPIO driver
While rebasing into setting bits instead of magic values,
I accidentally forgot to actually set the force bit.

Without it using the pins as GPIO-s did not actually work.

Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 7f2d9ccd09)
2021-03-29 22:26:27 +02:00
Tony Ambardar
6b2bcd2597 bpftools: fix libbpf pkgconfig file
The pkgconfig file hardcodes a host library directory which cannot be
overridden by OpenWrt during builds. Use SED to fix this and potential
include directory problems, as is done with several other packages.

This fixes a strange issue intermittently seen building iproute2 on the
oxnas target:

iptables modules directory: /usr/lib/iptables
libc has setns: yes
SELinux support: no
libbpf support: no
	libbpf version 0.3.0 is too low, please update it to at least 0.1.0
	LIBBPF_FORCE=on set, but couldn't find a usable libbpf

Fixes: 2f0d672088 ("bpftools: add utility and library packages
supporting eBPF usage")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit 9e64e4ce26)
2021-03-29 22:26:27 +02:00
Álvaro Fernández Rojas
f0ab4b17e6 gitignore: add .vscode for VS Code users
For Visual Studio Code users, .vscode is created inside the workspace.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 12dbad1a86)
2021-03-29 22:26:27 +02:00
Daniel Golle
c61d4eeedb ath79: fix RS-485 on Teltonika RUT-955
DTR GPIO isn't actually needed and triggers boot warning.
TX pin was off by one (GPIO 19 instead of GPIO 18).

Reported-by: @tophirsch
Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 53a7d5d614)
2021-03-29 22:26:27 +02:00
Aleksander Jan Bajkowski
eb1509a938 lantiq: set maximum kernel size for ARV7519RW22
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.

Set maximum kernel size and disable image building for this board.

Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
(cherry picked from commit c027dbac5a)
2021-03-29 22:26:27 +02:00
Eike Ritter
b89accdfbc ppp: compile fix: unset FILTER variable in Makefile
If the environment variable FILTER is set before compilation,
compilation of the ppp-package will fail with the error message

Package ppp is missing dependencies for the following libraries:
libpcap.so.1

The reason is that the OpenWrt-patch for the Makefile only comments
out the line FILTER=y. Hence the pcap-library will be dynamically
linked if the environment variable FILTER is set elsewhere, which
causes compilation to fail. The fix consists on explicitly unsetting
the variable FILTER instead.

Signed-off-by: Eike Ritter <git@rittere.co.uk>
(cherry picked from commit 46cd0765d0)
2021-03-29 22:26:27 +02:00
Russell Senior
290b28664d busybox: udhcpc, allow zero length dhcp options
This patch skips zero length DHCP options instead of failing.

Signed-off-by: Russell Senior <russell@personaltelco.net>
(cherry picked from commit 1c04365071)
2021-03-29 22:16:54 +02:00
Sven Eckelmann
eb98c88f66 mvebu: Fix mac addresses for GL.iNet GL-MV1000
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.

But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit c20ac84803)
2021-03-29 21:41:16 +02:00
Sven Eckelmann
7bb8aded10 mvebu: Add button support for GL.iNet GL-MV1000
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.

The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 01b911a938)
2021-03-29 21:38:24 +02:00
Tad Davanzo
9ce0f2b90c mvebu: enable WRT1900AC v1 and WRT32X for buildbots
Kernel size limits have been dealt with.
Effective revert of a1eb2c46 and ac9730c4.

Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit b4f76d9f0d)
2021-03-29 21:17:32 +02:00
Tad Davanzo
5a3b1e5b57 mvebu: venom resize kernel to 6MB
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0x900000, size 0x600000
	6291456 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "priKernSize";
	priKernSize=0x0600000

Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.

Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit 15309f5133)
2021-03-29 21:17:32 +02:00
Tad Davanzo
8458ebe18b mvebu: mamba resize kernel to 4MB
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0xa00000, size 0x400000
	4194304 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "pri_kern_size";
	pri_kern_size=0x400000

Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.

Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit 10415d5e70)
2021-03-29 21:17:31 +02:00
Tony Ambardar
7939d4a1b1 firewall3: update to latest git HEAD
This includes several improvements and fixes:

  61db17e rules: fix device and chain usage for DSCP/MARK targets
  7b844f4 zone: avoid duplicates in devices list
  c2c72c6 firewall3: remove last remaining sprintf()
  12f6f14 iptables: fix serializing multiple weekdays
  00f27ab firewall3: fix duplicate defaults section detection
  e8f2d8f ipsets: allow blank/commented lines with loadfile
  8c2f9fa fw3: zones: limit zone names to 11 bytes
  78d52a2 options: fix parsing of boolean attributes

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit 0d75aa27d4)
2021-03-29 20:26:33 +02:00
Ilya Lipnitskiy
2db7fe792e kernel: backports: mt7530: fix TRGMII mode after reset
Backport upstream patch that fixes TRGMII mode now that mt7530 is
actually resetting the switch on ramips devices.

Patches apply to both Linux 5.4 and 5.10, since TRGMII is broken on both.

Fixes: 69551a2442 ("ramips: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
(cherry picked from commit 680f91d0e5)
2021-03-29 13:41:24 +08:00
Hauke Mehrtens
112d1052ac kernel: Deactivate CONFIG_VFIO in generic kernel config
Instead of deactivating this in every target config, deactivate it once
in the generic kernel config. I was asked for this config option in a
x86 64 build in OpenWrt 21.02.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7d6553c72e)
2021-03-27 16:26:56 +01:00
Hauke Mehrtens
2464a9a8a4 kernel: bump 5.4 to 5.4.108
Refreshed all patches.

Compile-tested on: x86_64, ath79, lantiq
Runtime-tested on: x86_64, ath79

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-27 16:26:56 +01:00
Mauri Sandberg
e8cbdbbe97 ath79: Add support for Buffalo WZR-HP-G300NH
This device is a wireless router working on 2.4GHz band based on
Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103
wireless chip and Realtek RTL8366RB/S switches. Due to two different
switches being used also two different devices are provided.

  Specification:
  - 400 MHz CPU
  - 64 MB of RAM
  - 32 MB of FLASH (NOR)
  - 3x3:2 2.4 GHz 802.11bgn
  - 5x 10/100/1000 Mbps Ethernet
  - 4x LED, 3x button, On/Off slider, Auto/On/Off slider
  - 1x USB 2.0
  - bare UART header place on PCB

  Flash instruction:
  - NOTE: Pay attention to the switch variant and choose the image to
    flash accordingly. (dmesg / kernel logs can tell it)
  - Methods for flashing
    - Apply factory image in OEM firmware web-gui.
    - Sysupgrade on top of existing OpenWRT image
    - U-Boot TFPT recovery for both stock or OpenWRT images:
      The device U-boot contains a TFTP server that by default has
      an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot
      there is a time window, during which the device allows an image to
      be uploaded from a client with address 192.168.11.2. The image will
      be written on flash automatically.

      1) Have a computer with static IP address 192.168.11.2 and the
         router device switched off.
      2) Connect the LAN port next to the WAN port in the device and the
         computer using a network switch.
      3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A
         arp -s 192.168.11.1 02:AA:BB:CC:DD:1A
      4) Initiate an upload using TFTP image variant
         curl -T <imagename> tftp://192.168.11.1
      5) Switch on the device. The image will be uploaded subsequently.
         You can keep an eye on the diag light on the device, it should
         keep on blinking for a while indicating the writing of the image.

  General notes:
  - In the stock firmware the MAC address is the same among all
    interfaces so it is left here that way too.

  Recovery:
  - TFTP method
  - U-boot serial console

  Differences to ar71xx platform
  - This device is split in two different targets now due to hardware
    being a bit different under the hood. Dynamic solution within the same
    image is left for later time.
  - GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device
    cover, were the wrong way around and were renamed qos_on -> movie_off,
    qos_off -> movie_on. Associated key codes remained the same they were.

  The device tree source code is mostly based on musashino's work

Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
(cherry picked from commit bc356de285)
2021-03-27 07:47:07 +01:00
Mauri Sandberg
8e8fe69a8e ath79: cfi: cmdset_0002: amd chip 0x2201 - write words
Generally, in upstream CFI flash memory driver uses buffers for write
operations. That does not work with AMD chip with id 0x2201 and we must
resort to writing word sized chunks only. That is, to not apply general
buffer write functionality for this given chip.

Without the patch kernel logs will be flooded with entries like below:

MTD do_erase_oneblock(): ERASE 0x01fa0000
MTD do_write_buffer(): WRITE 0x01fa0000(0x00001985)
MTD do_erase_oneblock(): ERASE 0x01f80000
MTD do_write_buffer(): WRITE 0x01f80000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f8000a.
jffs2: Write clean marker to block at 0x01a60000 failed: -5
MTD do_erase_oneblock(): ERASE 0x01f60000
MTD do_write_buffer(): WRITE 0x01f60000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f6000a.
jffs2: Write clean marker to block at 0x01a40000 failed: -5

References: http://patchwork.ozlabs.org/project/linux-mtd/patch/20210309174859.362060-1-sandberg@mailfence.com/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to usptream fix submission]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8cc0fa8fac)
2021-03-27 07:46:48 +01:00
Mauri Sandberg
b526fbb1ce packages: kernel: add gpio-nxp-74hc153
NXP 74HC153 is a GPIO expander. Its original source cide sits in ar71xx
architecture tree. It has been slightly modified to get GPIO pin
configuration from the device tree rather than a MACH file.

 Changes to the source file:
  - Remove struct nxp_74hc153_config
  - in nxp_74hc153_probe(), fetch GPIO configuration from device tree
  - allow GPIO framework decide the base number by passing -1 to it
  - remove support for kernel versions below 4.5.0
  - add OF device compatibility string

 Create a package for inclusion in image.

References: https://lore.kernel.org/linux-gpio/545111184.50061.1615922388276@ichabod.co-bxl/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to driver usptreaming work in progress]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 6a6f9e73dd)
2021-03-27 07:46:14 +01:00
Eneas U de Queiroz
e7a9ee0580 openssl: bump to 1.1.1k
This version fixes 2 security vulnerabilities, among other changes:

 - CVE-2021-3450: problem with verifying a certificate chain when using
   the X509_V_FLAG_X509_STRICT flag.

 - CVE-2021-3449: OpenSSL TLS server may crash if sent a maliciously
   crafted renegotiation ClientHello message from a client.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 0bd0de7d43)
2021-03-27 07:34:35 +01:00
Paul Spooren
22149da1f4 build,json: backport default_packages fixes
Remove duplicate packages by running in `target/linux/` rather than
`target/linux/<target>/<subtarget>` and sort packages alphabetically.

Squash commit of:
7880a64848 build,json: 3rd fixup of default_packages
b36068d35d build,json: fixup fixup of arch_packages
1bf2b3fe90 build,json: fixup missing arch_packages

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-03-25 23:15:42 -10:00
Daniel Golle
aacf378608
mwlwifi: add PKG_FLAGS:=nonshared
This should fix the problem of mwlwifi-firmware-* not being found
when using the ImageBuilder.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9b3aaf1cdb)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-24 20:52:59 +00:00
Paul Spooren
fdc0342704 build,json: fix duplicates in default_packages
Calling without the DUMP=1 argument causes the target specific Makefile
to be "included" again which adds the target specific packages twice,
once on the actual run and once included from `include/target.mk`.

This led to duplicate package entries, causing confusion in downstream
projects using the generated JSON files.

While at it, apply `black` style to Python script.

Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 7f4c2b1a4f)
2021-03-23 12:47:18 -10:00
Florian Eckert
5a11ca3cf3 base-files: add logging for configuration import
Make sysupgrade backup import more verbose.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit fdbdbe8eaa)
2021-03-22 21:08:00 +01:00
INAGAKI Hiroshi
0444a93bdf ramips: add support for ELECOM WRC-1750GST2
ELECOM WRC-1750GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 256 MiB (NT5CC128M16JR-EK)
- Flash		: SPI-NOR 32 MiB (MX25L25645GMI-08G)
- WLAN		: 2.4/5 GHz 3T3R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/Keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX, from ethernet port side
  - 57600n8
- Power		: 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-1750GST2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC addresses:

LAN	: 04:AB:18:xx:xx:23 (Factory, 0xE000 (hex))
WAN	: 04:AB:18:xx:xx:24 (Factory, 0xE006 (hex))
2.4GHz	: 04:AB:18:xx:xx:25 (Factory, 0x4    (hex))
5GHz	: 04:AB:18:xx:xx:26 (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit b3ca1f30ef)
2021-03-22 21:07:34 +01:00
Walter Sonius
c459d5a710 ath79: fix lan port display order for sitecom wlr-7100
Physical port order watched from the back of the device is:
4 / 3 / 2 / 1 / WAN which also matches corresponding leds.
This patch corrects LuCI switch webpage LAN port order.

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[improve commit title, fix sorting in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 46c0634b50)
2021-03-22 21:06:40 +01:00
Jeff Collins
db6ff390b0 mvebu: add LED support for GL.iNet GL-MV1000
This patch enables LED support for the GL.iNet GL-MV1000

Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com>
[add SPDX identifier on new file, add aliases, minor cosmetic issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6e0c780eb3)
2021-03-22 21:05:41 +01:00
Álvaro Fernández Rojas
cd48473bb8 bcm27xx: bcm2711: correctly disable HW_RANDOM_BCM2835
It was removed in bac74aff5e, but it should have been disabled.
More info: https://forum.openwrt.org/t/make-image-stops-at-random-number-generator-bcm27xx/91429/7

Fixes: bac74aff5e ("bcm27xx: bcm2711: disable HW_RANDOM_BCM2835")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f93b544f01)
2021-03-22 08:09:13 +01:00
Hauke Mehrtens
bdfd7f68d0 uhttpd: update to git HEAD
15346de client: Always close connection with request body in case of error

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1170655f8b)
2021-03-21 22:39:38 +01:00
Hauke Mehrtens
741260d281 uhttpd: Execute uci commit and reload_config once
Instead of doing uci commit and reload_config for each setting do it
only once when one of these options was changed. This should make it a
little faster when both conditions are taken.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 501221af54)
2021-03-21 22:39:32 +01:00
Hauke Mehrtens
97a4d27fb5 uhttpd: Reload config after uhttpd-mod-ubus was added
Without this change the config is only committed, but the uhttpd daemon
is not reloaded. This reload is needed to apply the config. Without the
reload of uhttpd, the ubus server is not available over http and returns
a Error 404.

This caused problems when installing luci on the snapshots and
accessing it without reloading uhttpd.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d25d281fd6)
2021-03-21 22:39:27 +01:00
Magnus Kroken
69b4a11aed mbedtls: update to 2.16.10
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.

Security fixes:
* Fix a buffer overflow in mbedtls_mpi_sub_abs()
* Fix an errorneous estimation for an internal buffer in
mbedtls_pk_write_key_pem()
* Fix a stack buffer overflow with mbedtls_net_poll() and
mbedtls_net_recv_timeout()
* Guard against strong local side channel attack against base64 tables
by making access aceess to them use constant flow code

Full release announcement:
https://github.com/ARMmbed/mbedtls/releases/tag/v2.16.10

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
(cherry picked from commit dbde2bcf60)
2021-03-21 14:02:46 +01:00
Hans Dedecker
d52c5c081e glibc: update to latest 2.33 commit
db32fc27e7 test-container: Always copy test-specific support files [BZ #27537]
79c6be6a0a nptl: Remove private futex optimization [BZ #27304]
f90d6b0484 pthread_once hangs when init routine throws an exception [BZ #18435]
dd8023c2ac elf: ld.so --help calls _dl_init_paths without a main map [BZ #27577]
ea5a537e87 elf: Always set l in _dl_init_paths (bug 23462)
64f6c287ad x86: Handle _SC_LEVEL1_ICACHE_LINESIZE [BZ #27444]
32b9280f1d io: Return EBAFD for negative file descriptor on fstat (BZ #27559)

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
(cherry picked from commit 956490ad6a)
2021-03-21 14:01:10 +01:00
Hauke Mehrtens
31bca5f256 archs38: Add CONFIG_HZ=100
This kernel config option was missing and resulted in a question when
building.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 047b7621bb)
2021-03-19 18:01:55 +01:00
Hans Dedecker
d148fb1603 glibc: update to latest 2.33 commit (BZ #27462, BZ #27318, BZ #27389)
a151f2e05a nscd: Fix double free in netgroupcache [BZ #27462]
ee9f98d9ca x86: Set minimum x86-64 level marker [BZ #27318]
3e880d7337 nss: Re-enable NSS module loading after chroot [BZ #27389]
71b2463f61 x86: Add CPU-specific diagnostics to ld.so --list-diagnostics
a1eb3915e7 x86: Automate generation of PREFERRED_FEATURE_INDEX_1 bitfield
33dc1dd602 ld.so: Implement the --list-diagnostics option
8d4241b897 string: Work around GCC PR 98512 in rawmemchr
6efa2d44c8 S390: Add new hwcap values.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
(cherry picked from commit 0ef3c58ac8)
2021-03-18 23:01:53 +01:00
Rafał Miłecki
192486ac74 bcm53xx: backport first 5.13 DTS changes
This adds NVMEM bindings that are needed for proper booting on Linksys
devices.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 98d456a14e)
2021-03-17 23:38:46 +01:00
Rafał Miłecki
761df5c4cf bcm47xx: make WGT634U NVRAM patch apply again
Fixes: 1c48eee5b2 ("kernel: backport Broadcom NVRAM driver cleanups")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 9530b9bb78)
2021-03-17 23:38:46 +01:00
Rafał Miłecki
20fe0e66f3 bcm53xx: initialize NVRAM from NVMEM driver
NVRAM access may be needed early in boot process. Reading it using mtd
happens quite late in the init process. Add NVRAM initialization to the
NVMEM driver which comes up early and depends on IO mapping only.

This is required by Linksys devices which use NVRAM content for proper
partitioning (detecting current firmware partition).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit baf04eed02)
2021-03-17 23:38:46 +01:00
Rafał Miłecki
946bfd59a6 kernel: backport Broadcom NVRAM driver cleanups
Refactoring of bcm47xx_nvram driver. It's used by bcm47xx and bcm53xx.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1c48eee5b2)
2021-03-17 23:38:46 +01:00
Rafał Miłecki
3ce0d62b39 bcm53xx: backport NVMEM NVRAM driver
It supports NVRAM access described using DT binding. Right now NVRAM
data is exposed using /sys/bus/nvmem/ only.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 01b1b37528)
2021-03-17 23:38:46 +01:00