Here is corrected version (only thing not working are wifi LEDs).
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36578
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36459
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36456
Use eeprom (art) from included wifi card, not hard coded in flash.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36037
Error in using another MDIO (AP123 platform using only one GE1 device
for eth0 and eth1) for the router mr3420v2.
?onfirmed: https://forum.openwrt.org/viewtopic.php?pid=194779#p194779
Routers in this sense are the same and the only difference is: USB
port, USB led, instead of the GPIO-switch we have GPIO-button.
Signed-off-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36036
[juhosg: use gpio_request_one to enable the USB power]
Patch-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@opewrt.org>
SVN-Revision: 35961
LAN1 and LAN2 LEDs not present (it pulled to ground via
resistors) on MR3040 and MR11U devices. This little patch
enabling ability to control GPIO14 and GPIO15.
Patch-by: Dmytro <dioptimizer@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3439/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35960
[juhosg:
- remove custom mdio bus info and platform data for ar8327, clear the
.led_cfg field from dir835a1_setup instead,
- remove arguments of dir835c1_generic_setup function, register the
LEDs directly from the board specific setup instead]
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Patchwork: http://patchwork.openwrt.org/patch/3426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35957
Use the same MAC addresses as the original firmware.
Based on a patch from #10421.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Gabor Varga <vargagab@gmail.com>
SVN-Revision: 35730
This is platform definition for the RB951G device. It's mostly rework
of RB2011UAS patchset with network taken from the RB751 patches.
The main difference is the flash layout used by this device.
[juhosg:
- remove dead code from mach-rb951g
- add "-2HnD" suffix to the machine name
- use a separate 615-MIPS-ath79-RB951G-support.patch]
Patchwork: http://patchwork.openwrt.org/patch/3257/
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35633
We utilize many Routerboard 751's and discovered that our latest batch
of RB751's would not initialize the wireless radio. We have determined
Mikrotik has changed where the mac address was located inside hardconfig.
As such we utilize "routerboot_find_tag" to find the location of the mac
address. We should remove "RB751_MAC_ADDRESS_OFFSET" as it is ambiguous
by machine manufacturing date. The newer batch of RB751's that we received
had a RB751_MAC_ADDRESS_OFFSET 0x10.
Signed-off-by: Davey Hutchison <dhutchison@bluemesh.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35519
WDR3500 is similar to WDR3600 except it doesn't have gigabit ethernet,
and has only 1 USB port.
Pending issues:
* Leds are not working at all (except power and wlan_5g)
* LAN switch ethernet ports are reversed with respect to case label.
[Label] -> soft device
[LAN1] -> eth0.4
[LAN2] -> eth0.3
[LAN3] -> eth0.2
[LAN4] -> eth0.1
Based on http://patchwork.openwrt.org/patch/3208/
Thanks-to: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35423
[juhosg:
- remove unused GPIO stuff
- use a separate kernel patch for machine integration]
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35401
The PHY_SWAP and PHY_ADDR_SWAP bits are initialized
differently by different versions of the bootloader.
This leads to broken ethernet connection with OpenWrt
on some boards.
Turn both SWAP bits OFF on these boards to make it
consistent regardless of the bootloader used.
Based on a patch by Michel Stempin <michel.stempin@wanadoo.fr>.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35037
The mii_bus device is not required if phy_mask is zero.
The driver will use a fixed connection if it is not
specified.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34849
Based on the following patch:
http://patchwork.openwrt.org/patch/3043/
[juhosg:
- remove custom LED and button arrays
- use separate machine specific patch
- update Kconfig]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34779
