- sort device recipes alphabetically
- adjust board name of ELECOM WRC-2533GENT
- harmonize line wrapping
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Due to a typo, /boot is not properly unmounted after copying the backup
file to it. Fix the typo to solve this.
Fixes: 246916ddf4 ("brcm2708: use x86's upgrade scripts for all rpi targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While the other fq-based qdiscs take advantage of skb->hash and doesn't
recompute it if it is already set, sch_cake does not.
This was a deliberate choice because sch_cake hashes various parts of the
packet header to support its advanced flow isolation modes. However,
foregoing the use of skb->hash entirely loses a few important benefits:
- When skb->hash is set by hardware, a few CPU cycles can be saved by not
hashing again in software.
- Tunnel encapsulations will generally preserve the value of skb->hash from
before the encapsulation, which allows flow-based qdiscs to distinguish
between flows even though the outer packet header no longer has flow
information.
It turns out that we can preserve these desirable properties in many cases,
while still supporting the advanced flow isolation properties of sch_cake.
This patch does so by reusing the skb->hash value as the flow_hash part of
the hashing procedure in cake_hash() only in the following conditions:
- If the skb->hash is marked as covering the flow headers (skb->l4_hash is
set)
AND
- NAT header rewriting is either disabled, or did not change any values
used for hashing. The latter is important to match local-origin packets
such as those of a tunnel endpoint.
The immediate motivation for fixing this was the recent patch to WireGuard
to preserve the skb->hash on encapsulation. As such, this is also what I
tested against; with this patch, added latency under load for competing
flows drops from ~8 ms to sub-1ms on an RRUL test over a WireGuard tunnel
going through a virtual link shaped to 1Gbps using sch_cake. This matches
the results we saw with a similar setup using sch_fq_codel when testing the
WireGuard patch.
Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
A direct upgrade from previous swconfig version with
incompatible settings to DSA will break the internet.
Remove SUPPORTED_DEVICES so users cannot upgrade directly.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[rebase after Linksys rename, adjust title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Linksys devices in mvebu target feature a mixed naming,
where parts are based on the official product name (device
node, image; e.g. WRT3200ACM) and parts are based on the
internal code name (DTS file name, compatible, LED labels;
e.g. rango). This inconsistent naming has been perceived
as quite confusing.
A recent attempt by Paul Spooren to harmonize this naming
in kernel has been declined there. However, for us it still
makes sense to apply at least a part of these changes
locally.
Primarily, this patch changes the compatible in DTS and thus
the board name used in various scripts to have them in line
with the device, model and image names. Due to the recent
switch from swconfig to DSA, this allows us to drop
SUPPORTED_DEVICES and thus prevent seamless upgrade between
these incompatible setups.
However, this does not include the LED label rename from
Paul's initial patch: I don't think it's worth keeping the
enormous diff locally for this case, as we can implement
this much easier in 01_leds if we have to live with the
inconsistency anyway.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[rebase, extend to all devices, drop DT LED changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Currently enabling VLAN filtering blocks all traffic in the bridge
immediately. That is because DSA ignores all VLAN setup when VLAN
filtering is disabled, and when it is enabled, there is no VLAN entry
in the VLAN table, causing all traffic to be blocked.
Add patches to allow VLAN setup even if VLAN filtering is disabled.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Remove dependencies on core kernel headers in host tools used to build perf,
which break on any non-linux system
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MAC address is set in board.d script
Interface swapping is not needed anymore as switching to DSA breaks
previous configuration anyway
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
eth0 has HW MAC address while eth2 does not.
Use eth0 instead so we don't have to set LAN MAC manually.
Disable unused eth2, until multi CPU port is supported.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Update network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will break the ethernet.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Last reports with kernel 5.4 have all been positive [1], so let's open
this to a wider range of testers.
[1] https://github.com/openwrt/openwrt/pull/2804
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is useful when booting OpenWrt from ramdisks in order to have both
images partitions defined.
Furthermore, instead of always using img2 for the inactive image, let's use
img1 or img2 accordingly.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Previously the dts were using a value determined by empirical testing,
because of a spi driver/clock bug. The bug was fixed quite some time
ago. 33 MHz is the default clock frequency used by RouterBOOT and thus
safe.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Update the can-mcp251x-convert-to-half-duplex-SPI patch to fix reception
Some SPI host controllers such as the Cavium Thunder TX do not support
full-duplex SPI. Using half-duplex transfers allows the driver to work
with those host controllers.
This patch fixes the fact that mcp251x_hw_rx_frame was still relying on
a full-duplex transfer where bits were being shifted on MOSI at the same time
as MISO. After splitting the transaction into a spi_write_then_read() care
must be taken to ignore the first byte.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
- add fxos8700 support to GW52xx/GW53xx/GW54xx
- add USB_OTG support to GW552x
- add LSM9DS1 IMU support to GW560x
- add LSM9DS1 IMU support to GW5904
- add CC1352 UART to GW5910
- add BCM4330 support to GW5910
- fix wlan regulator for GW5910
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since commit 910df3f06c we have build in
on all X86/64 platforms the gpio-it87 driver.
Since this change I am getting the following error message on boot.
> kern.err kernel: [ 1.009416] gpio_it87: no device
I do not have this device on my system. To prevent the nonsensical
message and the loading of the module I have added this as a package, so
that it can be installed later or during image building.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
This is only a cosmetic correction, as the driver works as expected.
However, the error message confuses users about a missing reset definition.
On a defered init we don't see the following error message now:
[ 0.078292] ar7200-usb-phy usb-phy: phy reset is missing
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
This commit removes changes from upstream commits:
8e18c8e58da6 arm64: dts: marvell: armada-3720-espressobin: declare SATA
PHY property
bd3d25b07342 arm64: dts: marvell: armada-37xx: link USB hosts with their
PHYs
For most boards which have factory bootloader this caused that devices
connected to USB 3.0 and SATA port were not detected. For them to
function users would need to upgrade the bootloader to version with ARM
Trusted Firmware 2.1 or later. Unfortunately there is no official
bootloader image with updated ATF component, therefore drop these
properties from nodes. This change was also tested briefly with
bootloader with updated ATF and the ports functioned properly.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Enable the disk-activity LED trigger for ipq806x, since this SoC has an
onboard SATA controller.
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[split into separate commit]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Kernel config option LEDS_TRIGGER_IDE_DISK was renamed in kernel 4.8 to
CONFIG_LEDS_TRIGGER_DISK in upstream commit eb25cb9956cc ("leds: convert
IDE trigger to common disk trigger").
Removing it as it should be added only on targets which has usage for
this trigger.
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In FS#2738 we can see that patch first introduced in
e8ebcff ("ramips: add a explicit reset to dwc2")
breaks USB functionality since 18.06. Thus, this patch should be removed.
Removed:
- 0032-USB-dwc2-add-device_reset.patch
Fixes: FS#2738
Fixes: FS#2964
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
Since DEVICE_TYPE cannot be set per device, just set DEVICE_TYPE
to "nas" for the entire subtarget, which only contains this single
device.
Note that while this looks like a cosmetic change in combination
with the previous patches, this particular patch actually changes
the packages for the device.
Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While the effective "default" based on frequent use is "router", the
DEVICE_TYPE variable actually provides a "basic" configuration without
selecting any additional packages.
This is currently set up with the identifier "bootloader", which seems
to be not used at all. However, the only targets not using "router" or
"nas" are actually archs38 and arc770, which use their own value
"developerboard" for DEVICE_TYPE which seems to have been invented when
these targets where added. The latter is not implemented in target.mk,
though, and will fall back to the "basic" set of packages then.
So, to clean this up and make it more readable, let's just define a
DEVICE_TYPE "basic" and use it for the aforementioned cases.
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DEVICE_TYPE is a target/subtarget variable, and it does not have
any effect when set in a device definition. It can only be set
in a target's or subtarget's Makefile.
Consequently, having it set anyway is misleading, so this drops
all cases.
This effectively reverts the following commits:
7a1497fd60 ("apm821xx: MBL: set DEVICE_TYPE to NAS")
5b4765c93a ("gemini: Classify Raidsonic NAS IB-4220-B as a NAS")
cdc6de460b ("gemini: D-Link DNS-313 is a NAS")
For the following commit, the variable was set when adding device
support:
27b2f0fc0f ("kirkwood: add support for Iomega Storcenter ix2-200")
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some (older) CFEs are loaded at 0x80401000 and ramdisks are loaded at
0x80010000, which means that ramdisk size limit is 0x3F1000 (almost 4M).
Therefore, current ramdisks (~4MB) are overwritting CFE in these devices,
which results in a crash.
This commit changes the address where ramdisks are loaded to 0x80a00000,
which is the same address where kernel is loaded when booting from the flash.
Therefore, lzma-loader will now be loaded at 0x80a00000, but it will still
decompress the kernel at 0x80010000.
Tested with huawei,hg556a-b, which has its CFE loaded at 0x80401000.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Apparently, Sercomm allows loading a BCM WFI image via CFE, but this image
destroys "serial" and "protect" nand partitions, which is wrong.
It will also set both bootflags to the same value, which causes booting
issues with cferam (cferom will alternatively boot from cferam1 or cferam2
each time the device is rebooted).
Now that OEM Sercomm images are supported it's time to remove this hacky
cfe.bin image support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BCM6368 and newer devices are compatible with any lzma compression parameters.
Add a new legacy device definition and use it on BCM6358 and older devices.
Compressed kernel size is reduced by ~1.35%.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Allows to keep a backup firmware in case active firmware is corrupted.
Also fix hsspi address warning.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
When firmware is flashed, cferam.000 extension is renamed to the next number.
When booting, CFE scans the NAND and picks the partition with the highest
cferam extension and ignores the other one.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This images can be flashed from the official firmware, as opposed to CFE
images, which can only be flashed from CFE and require opening the case.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The only Sercomm WFI user has been migrated to a dedicated firmware parser.
Keep support for no cferam partition based on a boolean DT property.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Support Sercomm firmware partition split.
WFI partition must be defined after bootflag partitions in order for the
parser to properly find bootflag1 and bootflag2 partitions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sercomm uses 2 bootflag partitions and boots the firmware with the highest
bootflag. Support splitting the firmware partition while keeping support for
unsplitted layout.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.
Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.
Related: commit 27f3f493de ("gpio-button-hotplug: unify polled and
interrupt code")
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link RE450 v3 is a dual band router/range-extender based on
Qualcomm/Atheros QCA9563 + QCA9880.
This device is nearly identical to RE450 v2 besides a modified flash
layout (hence I think force-flashing a RE450v2 image will lead to at
least loss of MAC address).
Specification:
- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button-
- possible UART header on PCB¹
Flash instruction:
Apply factory image in OEM firmware web-gui.
¹ Didn't check to connect as I didn't even manage to connect on
RE450v2 (AFAIU it requires disconnecting some resistors, which I was
too much of a coward to do). But given the similarities to v2 I
think it's the same or very similar procedure (and most likely also
the only way to debrick).
Signed-off-by: Andreas Wiese <aw-openwrt@meterriblecrew.net>
[remove dts-v1 and compatible in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
[V1] http://192.168.0.1
[V2] http://192.168.0.254
Default user is "admin" & password is "admin".
On V2, there is no DHCP server running by default, so remember to set
IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
[V1] "*.factory.bin"
[V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model
Web interface may complain if filename is too long. In such case,
rename .bin to something shorter.
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Notes:
When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.
The MAC address assignment has been checked with OEM firmware.
Installation manual based on ar71xx support by Thomas Roberts
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.
Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.
Fix it.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION
to be at least 8.5.3, otherwise the image is rejected:
New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3
Versions: New(525568) 8.5.0, Required(525571) 8.5.3
Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3'
For consistency, also increase version number for XC devices.
Tested-by: Pedro <pedrowrt@cas.cat>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.
In addition, a look into the manual revealed that the OEM
configuration is as follows:
LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless
So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We currently support three kernel versions on this target, let's
just get rid of the oldest one.
Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We currently support three kernel versions on this target, let's
just get rid of the oldest one.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.
This led to bootloops after using sysupgrade.
Fixes: FS#3118
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Also removes random module and switches to new bcm2711 thermal driver.
Boot tested on RPi 4B v1.1 4G.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch backports additional fixes for XDP support in the mvneta driver. These
changes are found upstream as commits:
b37fa92e20ef2 net: mvneta: fix build skb for bm capable devices
f383b2950070c net: mvneta: rely on page_pool_recycle_direct in mvneta_run_xdp
79572c98c554d mvneta driver disallow XDP program on hardware buffer management
44efc78d0e464 net: mvneta: fix XDP support if sw bm is used as fallback
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
This patch backports XDP support in the mvneta driver used by Marvell ARMADA 37x,
38x and 37xx series SoCs. Supported actions are:
- XDP_DROP
- XDP_PASS
- XDP_REDIRECT
- XDP_TX
Patches are present upstream as following commits:
* b0a43db9087a net: mvneta: add XDP_TX support
* 9e58c8b41065 net: mvneta: make tx buffer array agnostic
* fa383f6b77a2 net: mvneta: move header prefetch in mvneta_swbm_rx_frame
* 0db51da7a8e9 net: mvneta: add basic XDP support
* 8dc9a0888f4c net: mvneta: rely on build_skb in mvneta_rx_swbm poll routine
* 568a3fa24a95 net: mvneta: introduce page pool API for sw buffer manager
* ff519e2acd46 net: mvneta: introduce mvneta_update_stats routine
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
This commit introduces support for R/W access to the CPU frequency
setting of routerboot on ath79 hardware.
On unsupported hardware, the sysfs attribute will expose the raw tag
value (read-only) to help with reverse engineering its meaning.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This routine will be shared between hard and soft config drivers.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This driver exposes the data encoded in the "soft_config" flash segment
of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder
named "soft_config" through a set of human-and-machine-parseable
attributes. Changes can be discarded by writing 0 to the 'commit'
attribute, or they can be committed to flash storage by writing 1.
This driver does not reuse any of the existing code previously found in
the "rbcfg" utility and makes this utility obsolete by providing a clean
sysfs interface.
Like "rbcfg", this driver requires 4K_SECTORS support since the flash
partition in which these parameters are stored is typically 4KB in size.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This routine will be shared between hard and soft config drivers.
Also use scnprintf() instead of snprintf().
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
For the sake of strictly typed code, add a missing const qualifier.
Add a missing return value in error path.
Check the return value of mtd_read(), for good measure.
Also demote the error printks of failed sysfs file creation to warn
level since they are not fatal in the init() sequence.
Finally, add a note regarding PAGE_SIZE and clarify a comment.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The depends and select should apply to the sysfs driver, not the meta
config.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
CPE with a single Ethernet port and a 802.11bgn radio.
Specifications:
- QCA9531 SoC
- 1x 10/100 Mbps Ethernet with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 5 dBi built-in antenna
- POWER/LAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI.
The U-boot bootloader also contains a backup TFTP client to upload the
firmware from. Upon boot, it checks its ethernet network for the IP
192.168.1.10. Host a TFTP server and provide the image to be flashed as
file firmware_auto.bin.
MAC address setup:
The art partition contains four consecutive MAC addresses:
0x0 aa:bb:cc:xx:xx:c4
0x6 aa:bb:cc:xx:xx:c6
0x1002 aa:bb:cc:xx:xx:c5
0x5006 aa:bb:cc:xx:xx:c7
However, the manufacturer in its infinite wisdom decided that one address
is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's
overwriting the existing and valid address in 0x1002). This is obviously
also the address on the device's label.
Signed-off-by: Pavel Balan <admin@kryma.net>
[fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename
ATH_SOC to SOC]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
AHB is 258 MHz for this device (CPU_PLL / 3), but there is no difference
between 64 MHz and 50 MHz for spi-max-frequency, thus increase to 50 MHz.
Tested on revisions C1 and C3.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
GPIO 11 needs to be pulled high for the external gigabit switch to work,
this is currently solved via gpio-hog. Replace with phy0 reset-gpios.
Tested on revisions C1 and C3. Reset button is still working for reboot,
to enter failsafe, and to enter bootloader http recovery.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The device has a total of 8 LEDs, 5 of which are controlled by the switch
(LAN 1-4, WAN). Only power, wifi and wps are controlled by the SoC.
* led_power is on GPIO 5 (not 15), boot flashing sequence is now visible
* remove led 'internet', since it is only connected to the switch
* remove ucidef_set_led_switch for WAN from 01_leds, as it has no effect
Tested on revisions C1 and C3.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* MediaTek MT7620A (580 Mhz)
* 8 MB of FLASH
* 64 MB of RAM
* 2.4Ghz and 5.0Ghz radios
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* UART header on PCB (57600 8n1)
* Green/Orange Power LEDs illuminating a Power-Button Lens
* Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
* 3x button - wps, power and reset
* U-boot bootloader
Installation:
The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either
the TEW-810DR or DIR-810L and is located at
source/user/wolf/cameo/ncc/hostTools.
The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"
This may need to be altered if your hardware version is "1.1R".
The image can also be directly flashed via serial tftp:
1. Load *.sysupgrade.bin to your tftp server directory and rename for
convenience.
2. Set a static ip 192.168.10.100.
3. NIC cable to a lan port.
4. Serial connection parameters 57600,8N1
5. Power on the TEW-810 and press 4 for a u-boot command line prompt.
6. Verify IP's with U-Boot command "printenv".
7. Adjust tftp settings if needed per the tftp documentation
8. Boot the tftp image to test the build.
9. If the image loads, reset your server ip to 192.168.1.10 and restart network.
10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.
Notes:
The only valid MAC address is found in 0x28 of the factory partition.
Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[remove "link rx tx" in 01_leds, format and extend commit message,
fix DTS led node names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The UBIFS_FS_ZSTD is exposed when UBIFS is enabled.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between 4.19 and 5.4, the kernel moved the partition parsers into
the parsers subdirectory. This led to some necessary rebasing of
our local patches for parsers, which partially has been performed
without caring about where the code was inserted.
This commit tries to adjust our local patches so that parsers are
inserted at the "proper" positions with respect to alphabetic sorting
(if possible). Thus, the commit is cosmetic.
While this might look useless now, it will make life easier when
adding other parsers in the future or for rebasing on kernel changes.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
