* updated SNAND/SNFI driver brings support for MT7981
* add support for MediaTek NAND Memory bad Block Management (NMBM)
(not used for any boards atm, but could be useful in future)
* wire up NMBM support for MT7622, MT7629, MT7981 and MT7986
* replace some local patches with updated version from SDK
* bring some legacy precompiler symbols which haven't been converted
into Kconfig symbols in U-Boot 2022.07, remove when bumbping to
U-Boot 2022.10:
100-28-include-configs-mt7986-h-from-SDK.patch
Source: https://github.com/mtk-openwrt/u-boot
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MediaTek's ARM Trusted Firmware v2.7+ allows the images inside a FIP
structure to be compressed. Make use of that for boards with NOR flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Truncating a UBI volume using `ubi write 0x0 volname 0x0` results in
segfault on newer U-Boot. Write 1MB of 0s instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Image names as well as the calculation of the padded image size did
not work as intended. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import a3ba6adb70 arm: dts: mt7622: remove default pinctrl of uart0
and apply also to locally added boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
swig has been installed on the buildbots a while a ago and
Petr Štetiar got a fix for the pylibfdt error. Use that and re-enable
the builds for mt7620 and mt7621.
Refresh patches while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let U-Boot handle free space in UBI partitions by recognizing the EOF
marker OpenWrt is using as well for that purpose.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building U-Boot for the MT7621 SoC requires binman, a Python-based
host tool to generate images. For now, binman cannot work inside the
OpenWrt build system because it requires swig, so mark the MT7621
boards as borken to fix the ramips/mt7621 build until someone with
knowledge about Python and swig fixes the underlaying issue.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Merge uboot-ramips into uboot-mediatek.
* Port support for the RAVPower RP WD009 to U-Boot 2022.07.
* Add support for MT7621 and add builds for the reference boards.
* Add builds for MT7620 and MT7628 reference boards.
This should help to make development of U-Boot-level board support for
all MediaTek targets much easier.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to fix host-build of the mkimage tool without
CONFIG_TOOLS_LIBCRYPTO.
Update and refresh all patches.
Tested on BananaPi R64 (MT7622) successfully booting from SD card,
eMMC and SPI-NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Select matching U-Boot for both v1 and v2 variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace pending patch with version accepted upstream.
Other than in the first suggested version, the new property is now
called 'u-boot,bootconf' instead of 'bootconf'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove '0x' prefix from pstore node in dts, just like it was done
for the device tree used by Linux on MT7622.
This change is done in preparation to update U-Boot to 2022.04.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Store selected boot configuration in '/chosen' node in device tree, so
it can be accessed by Linux (and used for fine-tuning the FIT partition
parser).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Brings bootmenu and production/recovery dual-boot scheme like on
the BPi-R2, BPi-R64, E8450 and UniFi 6 LR.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Using Host/Exports doesn't work as intended, explicitly add the
required vars so that u-boot finds the required libraries when building
its tools.
Signed-off-by: Andre Heider <a.heider@gmail.com>
U-Boot 2021.10 has been released.
Rebase mediatek patches on top of new release and remove some patches
which have been merged upstream.
Tested on Bananapi BPi-R2 (mt7623), Bananapi BPi-R64 (mt7622) and
Linksys E8450 (mt7622).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix BPi-R2 GPIO LEDs to indicate boot into production or recovery
firmware in DTS and define them in default environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
BananaPi BPi-R2 comes with HDMI and MIPI-DSI. Use dislpay facility in
Linux by add "console=tty1" boot argument.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As the board name was changed to be identical to the device tree
compatible string (just like for other boards), also reflect that
change for U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* use built-in default environment instead of file in bootfs
* get rid of bootfs alltogether and use uImage.FIT
* auto-detect boot device like original script did
* add support for factory button
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ! Behavior change !
Old behavior: If the Reset button is held down during power-on
do factory reset and try booting recovery from TFTP forever.
If valid recovery is received via TFTP, write it to flash and boot.
New behavior: If the Reset button is held down during power-on
do factory reset, then try TFTP *once*, then try booting on-flash
recovery, then keep trying via TFTP forever until a valid image is
received.
Only if there is no bootable recovery stored on flash, store the
downloaded recovery. Then boot it.
* Set loadaddr to 0x48000000 in order to allow booting images larger
than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to
0x48000000 gives us 384MB on devices with 512MB RAM, which should be
more than enough as a maximum size for uImage.FIT to be loaded.
* Widely unify device-specific default environment in preparation to
auto-generate it from parameters.
* backport upstream commit fixing MBR/DOS partitioning
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for pstore/ramoops now that DRAM content is preserved
over reboot on MT7622. On each boot, check pstore and boot to recovery
image in case there are records stored in it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
mtd erase needs to be aligned with erase blocks. Use padded image size
for erasing the production volume.
As the environment grew above the current size of 0x1000 bytes by
introducing the new padding function, increase the env size to 0x4000.
While at it, clean up reset button function to work to more reliable on
that board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Erase firmware ereas before writing to recovery or production partition
when updating them via the bootloader menu.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* check image checksums before writing to flash
* only bootmenu_0...9 are working, remove bootmenu_a entry
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Build U-Boot for booting from SPI-NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Add U-Boot build for the Ubiquiti Networks UniFi 6 LR access point.
This allows updating the bootchain to modern ARM Trusted Firmware 2.4
and U-Boot 2021.04 while keeping as much of the existing flash layout
as possible (u-boot-env, factory and eeprom partitions are retained),
gaining robust recovery vs. production dual-boot mechanism.
Add info for the Winbond W25Q512JV SPI NOR flash used in the device
and wait for GPIOs to settle after reset before checking for reset
button.
I2C connected LED controller is not supported yet.
Writing large amounts of data to SPI flash currently doesn't work due
to watchdog timeout causing reset before data write completes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that sdcard.gz image contains everything needed to boot straight
into production image, no longer force booting into recovery image on
first boot by removing the logic which implemented that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow selecting either SATA or PCIE functionality using uImage.FIT
configurations and device-tree overlays.
By default, PCIE1 is selected (as it has been before this change).
To select SATA instead, you can do this now:
fw_setenv bootconf config-mt7622-bananapi-bpi-r64-sata
and reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make installation to eMMC more convenient on the BPi-R64 by also
copying the production image (if valid) from SD Card to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of building all U-Boot variants by default, build only those
needed by the selected board(s).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch form Frank Wunderlich <frank-w@public-files.de> to fix
build of MediaTek AHCI SATA driver.
Enable that driver on Bananapi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Copy patch added to uboot-sunxi by commit 3cc57ba462
("uboot-sunxi: add missing type __u64") also to uboot-mediatek.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* make sure USB 2.0 works (useful for UEFI-booting eg. memtest86)
* include more useful U-Boot config options on BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MediaTek published their current U-Boot patchset on github:
https://github.com/mtk-openwrt/u-boot/commits/mtksoc
Import the platform patches from there (`00-mtk-*.patch`), arrange,
them nicely, drop no longer needed local patches and rebase on top of
U-Boot 2021.04-rc3.
Tested and works well on Linksys E8450 (snand-1ddr) as well as
Bananapi BPi-R64 (sdmmc-2ddr, emmc-2ddr).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* allow MAC address from U-Boot env to be inhertied
* allow eMMC installation to succeed also without recovery present
on the SD Card.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
