Commit Graph

5 Commits

Author SHA1 Message Date
Chuanhong Guo
b756ea2a90 ramips: replace pinctrl property names
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:29:17 +08:00
Chuanhong Guo
0b68d081eb ramips: mt7628: update dts for upstream gpio-mt7621 driver
upstream driver merged 3 separated gpio banks into one gpio node.
and gpioX Y in our local driver should be replaced with gpio X*32+Y.

This patch is created using the following sed command:
sed -i -r 's/(.*)gpio([0-9]) ([0-9]+)(.*)/echo "\1gpio $((\2*32+\3))\4"/ge'

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Adrian Schmutzler
e4ce3109f2 ramips: simplify state_default/pinctrl0 in device DTS files
The node pinctrl0 is already set up in the SOC DTSI files, but
defined again as member of pinctrl in most of the device DTS(I)
files. This patch removes this redundancy for the entire ramips
target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-23 02:24:55 +01:00
Adrian Schmutzler
231dc26867 treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.

This removes the identifier from all DTSI files in /target/linux.

Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx

This does not touch ipq806x for now, as the bump to 4.19 is close.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 16:44:06 +01:00
Sungbo Eo
b7ec6659a1 ramips: add support for ipTIME A3
ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
  - Switch: SoC internal
- UART:
  - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-09-25 14:44:36 +08:00