Commit Graph

1624 Commits

Author SHA1 Message Date
Thibaut VARÈNE
4cd44e5dc7 ar71xx: mikrotik: mach-rbspi.c remove wlan id
Following on the previous commit, this patch removes useless id argument
from rbspi_wlan_init().

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:43:38 +02:00
Thibaut VARÈNE
3fecb06fb1 ar71xx: mikrotik: bypass id check in __rb_get_wlan_data()
The id parameter in __rb_get_wlan_data() was incorrectly used on the
assumption that id "0" would always be tied to ath9k with RLE encoding
and positive id (in fact, only id "1" was valid) would always be tied to
("external") ath10k with LZO encoding.

Newer hardware revisions of supported devices prove this assumption to
be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO
compressed, so disable this check to allow newer hardware to correctly
decode caldata for ath9k. Since ath10k caldata is no longer pulled from
this implementation, this commit also disables the publication in sysfs
to avoid wasting memory.

Note: this patch assumes that ath9k caldata is never stored with the new
"LZOR" encoding scheme found on some ath10k devices.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:43:38 +02:00
Baptiste Jonglez
f5b3cd1539 ar71xx: Fix gigabit switch support for Mikrotik RB951G-2HnD
Without this patch, when using rev 3 of the Atheros AR9344 SoC, the
gigabit switch (AR8327) does not work or works very erratically.

This is a re-spin of http://patchwork.ozlabs.org/patch/419857/ with a
different PLL value, according to the feedback from several users
(including myself) as shown here:

  https://openwrt.org/toh/mikrotik/rb2011uias#tracking_reported_experience_with_suggested_patch_for_the_5_gige_ports

Performance is acceptable: testing L3 forwarding without NAT yields a
performance of 370 Mbit/s (iperf3 TCP) and 41 Kpps (iperf3 UDP with 64
bytes payload). Both tests show that 100% of CPU time is spent on softirq.

A similar fix for a different device (RB2011) was added in e457d22261
("Make GBit switch work on RB2011").

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
(cherry picked from commit 247043c968)
2020-03-28 13:46:26 +01:00
Adrian Schmutzler
83f1015a6c ar71xx: fix swapped LAN/WAN MAC address for Archer C60 v1/v2
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:

lan   *:7b   label
wan   *:7c   label+1
2.4g  *:7b   label
5g    *:7a   label-1

Only one address is stored in <&mac 0x8>, corresponding to the label.

This has been checked on revisions v1, v2 and v3.

Since ar71xx calculates the ath10k MAC address based on the ethernet
addresses, the number there is adjusted, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14eb54938b)
2020-03-14 13:20:18 +01:00
Catrinel Catrinescu
68351990dc ar71xx/ath79: ew-dorin, fix the trigger level for WPS button
Because the WPS button had the wrong trigger level,
the failsafe mode was triggered quite often,
after this commit:
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=27f3f493de

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
(cherry picked from commit 3e03b7ac4a)
2020-03-11 11:26:06 +01:00
David Bauer
ef391799e3 ar71xx: correct AVM FRITZ Repeater 450E WPS button flag
The AVM FRITZ!WLAN Repeater 450E's WPS button is not active low.

Correct the active low flag to avoid unintenional activation of
failsafe mode on boot.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1d4f2ca610)
2020-03-01 18:42:05 +01:00
Sungbo Eo
27eea24921 ar71xx: fix MAC address setup for TL-WDR4300 board
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:

OpenWrt: lan = label_mac -2, wan = label_mac -2
  stock: lan = label_mac,    wan = label_mac +1

This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 9b02d32e34)
2019-12-21 00:31:39 +01:00
Adrian Schmutzler
8fac0b398c ar71xx: fix buttons for TP-Link TL-WDR4900 v2
TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so
don't set up an RFKILL for this device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 25127f58b4)
2019-11-21 12:29:54 +01:00
Adrian Schmutzler
3c65c47ce6 ar71xx: fix LED setup for TL-WDR4900 v2
In ar71xx there is only one combined mach file for Archer C5/C7 and
TL-WDR4900 v2. This one uses the same LED struct for all devices,
defining "green" LEDs for them. However, WDR4900 uses blue front
LEDs, while only C5/C7 uses green ones. Despite, in base-files
WDR4900 is actually set up with "blue" for the mentioned LEDs.

Thus, this patch creates a separate LED struct for WDR4900, so the
LEDs can be set up correctly. Despite, the wlan5g LED is removed as
it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7).

Note: While front LEDs are blue, USB LEDs (on the back) are green,
so colors are mixed intentionally for the WDR4900 v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 93f2bcc35e)
2019-11-21 12:29:47 +01:00
Adrian Schmutzler
e945c43142 ar71xx: fix MAC address setup for TL-WDR4900 v2
The MAC address setup of the TL-WDR4900 v2 is different from the
C5/C7. This aligns ar71xx with the setup in ath79:

wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a9d3084b83)
2019-11-21 12:29:28 +01:00
Adrian Schmutzler
8a21bc3622 ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2
As discussed in 1d18a14a90 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...

Fixes: FS#408

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a021268032)
2019-11-21 12:29:20 +01:00
Adrian Schmutzler
b3514e3569 ar71xx: improve support for TP-Link CPE510 v2
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.

Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).

With this patch, we provide proper support for this device in ar71xx.

Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
  for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254

Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c79b796280)
[added CPE510V2 entry to tplink-safeloader.c]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:13:27 +01:00
Michal Cieslakiewicz
4fb6b8c553 ar71xx: WNR2200: remove redundant GPIO for WLAN LED
Without this patch, an extra entry appears for AR9287 GPIO
that duplicates WLAN LED but in fact drives nothing:

gpiochip1: GPIOs 502-511, ath9k-phy0:
 gpio-502 (                    |netgear:blue:wlan   ) out hi
 gpio-503 (                    |netgear:amber:test  ) out hi
 gpio-504 (                    |netgear:green:power ) out lo
 gpio-505 (                    |rfkill              ) in  hi
 gpio-507 (                    |wps                 ) in  hi
 gpio-508 (                    |reset               ) in  hi
 gpio-510 (                    |ath9k-phy0          ) out hi <===!

The pin pointed above is default LED GPIO (8) for AR9287.
For WNR2200 it is not connected anywhere - pin 0 drives blue WLAN
LED instead - but initialization code is missing that information.

This fix calls ap9x_pci_setup_wmac_led_pin() function at device
setup, forcing WLAN LED pin to be 0 and removing redundant entry.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-08-30 23:20:09 +02:00
Koen Vandeputte
0a59e91973 ar71xx/ath79: ag71xx: dont fetch the same var again
tx_size was just declared above and set to BIT(tx->order)
Use the declaration instead, which could avoid a pointer deref

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 6852eab58236e3991f5d73f211018dfef01f2a64)
2019-08-27 10:31:06 +02:00
Koen Vandeputte
db1a935e5c ar71xx: ag71xx: use base address value directly from the source
This brings the code more inline with the ath79 flavour

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:31:06 +02:00
Koen Vandeputte
8d78aa8eaf ar71xx: ag71xx: make use of managed dev API simplifying code
Backport of a4eef43a12 ("ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev")
combined with the initial changes from John Crispin.

Simplifies the code a lot by using the Managed dev API.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:31:06 +02:00
Koen Vandeputte
c9b28b5703 ar71xx: ag71xx: replace ag71xx_get_phy_if_mode_name with phy_modes()
Backport of f73b2d64ed ("ath79: ag71xx: replace ag71xx_get_phy_if_mode_name() with phy_modes()")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:31:06 +02:00
Koen Vandeputte
d143a0a4f6 ar71xx: ag71xx: pass correct device pointer to dma functions
Backport of 4eaa3626a8 ("ath79: ag71xx: pass correct device pointer to dma functions")

While 4.14 does not contain the warnings,
it still makes sense to use the proper pointers here.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:31:06 +02:00
Koen Vandeputte
42b42d2c9b ar71xx/ath79: ag71xx: get ring_mask consistent
All other instances of this identical declaration fetch the
value directly from the ring_order.

Also do it here.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:31:06 +02:00
Koen Vandeputte
576791b9b4 ar71xx: ag71xx: add missing register writes
These are added in ath79, but were not backported here

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:31:06 +02:00
Koen Vandeputte
62eae4805b ar71xx: ag71xx: init rings with GFP_KERNEL
ar71xx got lost during final rebase ..

Fixes: c8a6ce71e4 ("ar71xx/ath79: ag71xx: init rings with GFP_KERNEL")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-09 18:52:21 +02:00
Koen Vandeputte
dda342abba ar71xx/ath79: ag71xx: fix sleep in atomic
When enabling atomic-sleep-debugging options in the kernel,
following splat is seen when disabling the interface (which happens on boot):

[   10.892878] eth0: link down
[   10.896788] BUG: sleeping function called from invalid context at net/core/dev.c:5563
[   10.904730] in_atomic(): 1, irqs_disabled(): 1, pid: 425, name: ip
[   10.911004] 2 locks held by ip/425:
[   10.914539]  #0:  (rtnl_mutex){....}, at: [<80377474>] rtnetlink_rcv_msg+0x2d8/0x380
[   10.922441]  #1:  (&(&ag->lock)->rlock){....}, at: [<80330158>] ag71xx_hw_disable+0x24/0x94
[   10.930976] CPU: 0 PID: 425 Comm: ip Not tainted 4.14.136 #0
[   10.936716] Stack : 805e0000 80589228 80557404 876998ec 80610000 80610000 87cdcafc 805b5327
[   10.945233]         80551534 000001a9 8061386c 87699ccc 87cfb180 00000001 876998a0 84f70903
[   10.953751]         00000000 00000000 80b00000 8769979c 6a7407fa 00000000 00000007 00000000
[   10.962270]         000000b7 16d0954a 000000b6 00000000 80000000 87cb658c 87cb65b0 00000001
[   10.970787]         8046f97c 87699ccc 87cfb180 87ff2810 00000003 802ce724 0806e098 80610000
[   10.979306]         ...
[   10.981797] Call Trace:
[   10.984287] [<8006cb0c>] show_stack+0x58/0x100
[   10.988814] [<800aab34>] ___might_sleep+0x100/0x120
[   10.993774] [<8035c434>] napi_disable+0x30/0xd8
[   10.998377] [<80330198>] ag71xx_hw_disable+0x64/0x94
[   11.003418] [<8033069c>] ag71xx_stop+0x24/0x38
[   11.007959] [<80359e30>] __dev_close_many+0xcc/0x104
[   11.013009] [<80362eac>] __dev_change_flags+0xc8/0x1ac
[   11.018227] [<80362fb8>] dev_change_flags+0x28/0x70
[   11.023182] [<80376890>] do_setlink+0x31c/0x91c
[   11.027786] [<80379360>] rtnl_newlink+0x3ec/0x7f8
[   11.032563] [<80377498>] rtnetlink_rcv_msg+0x2fc/0x380
[   11.037799] [<8039a734>] netlink_rcv_skb+0xd4/0x178
[   11.042754] [<80399d10>] netlink_unicast+0x168/0x250
[   11.047796] [<8039a2d4>] netlink_sendmsg+0x3d8/0x434
[   11.052841] [<8033f0e4>] ___sys_sendmsg+0x1dc/0x290
[   11.057794] [<80340140>] __sys_sendmsg+0x54/0x84
[   11.062495] [<8007212c>] syscall_common+0x34/0x58

This is caused by calling napi_disable() while holding the spinlock.

Fix it by omitting the spinlock, which is not required here
Extensively tested on GL-MiFi, RB-912 and RB-922 hardware

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-09 18:32:38 +02:00
David Bauer
862352cdbd ar71xx: fix HiveAP 121 PLL for 1000M
The Aerohive HiveAP 121 has the wrong PLL value set for Gigabit speeds,
leading to packet-loss. 10M and 100M work fine.

This commit sets the Gigabit Ethernet PLL value to the correct value,
fixing packet loss.

Confirmed with iperf and floodping.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cb49e46a8a)
2019-08-01 21:29:43 +02:00
Tomislav Požega
c59e24ca30 ar71xx: Archer C7 v1 LED names and RFKILL fixes
All leds on these boards are green. v1 has RFKILL GPIO 23 for production
units (it had GPIO 13 only for test phase units, and these are rather
very rare to find). As for the previous attempt to fix this and revert
due to WDR boards have blue leds, it was wrong: WDR board does not use
common setup (false).

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit c79c001b59)
2019-07-28 23:25:11 +02:00
Etienne Champetier
76a4c93f9d ar71xx: enable SGMII fixup on Mikrotik wAP AC
fixes intermittent loss of connectivity on 1Gbit port, with log message:
> 803x_aneg_done: SGMII link is not ok

Thanks to David Bauer for pointing me in the right direction.
I just had to figure out the right bus_id, which you find in this log:
> ag71xx ag71xx.1: connected to PHY at gpio-1:00 [uid=004dd074,
  driver=Atheros 8031 ethernet]

Fixes FS#2236

Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
[Wrapped commit message - Fixed whitespace erors]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2a7519e29d)
2019-07-21 13:09:31 +02:00
Koen Vandeputte
b947de25a6 ar71xx: fix nand init issues on some rb2011 devices
While flashing lots of RB2011 devices, I noticed that
some of them refused to boot properly, failing over the NAND parameters.

Checking in detail shows that some device seem to use another NAND flash
which only support standard 2048-byte pages, without 512-byte subpage support.

This commit disables usage of these small subpage completely.

Advantages:
- Both NAND's with(out) subpage support are working now
- The nand speed increases a bit (measured roughly 1%) in typical usecases

Disadvantages:
- The maximum storage capacity decreases by ~0.2%
as small changes can consume a full page (2048 bytes) now.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-07-12 09:39:33 +02:00
W. Michael Petullo
cb9db2a0c3 ar71xx: fix ath79/rb4xx IRQ initialization on kernel 4.14
Apply the same approach as in commit 3b53d6fdbc ("ar71xx: fix pci irq
init on kernel 4.14") to fix IRQ initialization for ath79-based chipsets
on rb4xx.

Ref: PR#2182
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: W. Michael Petullo <mike@flyn.org>
[commit ref fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8c7d6c47a7)
2019-07-03 07:47:38 +02:00
Petr Štetiar
971d358579 ar71xx: ag71xx: update ethtool support
Remove references to broken and mostly deprecated phy_ethtool_ioctl, use
new {s,g}et_link_ksettings and add nway_reset which was previously
handled in phy_ethtool_ioctl.

Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Petr Štetiar
eafe0611d9 ar71xx: ag71xx: remove unused SIOCETHTOOL ioctl handling
This ioctl is currently routed through generic interface code:

  dev_ioctl
    dev_ethtool
      __ethtool_get_link_ksettings
        phy_ethtool_ioctl

Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Alexander Couzens
8357b8131c
ar71xx: wr940 v4/v6: correct lan interface mac address
The vendor firmware only uses two mac addresses, the mac address on the
label and the label + 1. While checking multiple devices, all labels have
even mac addresses. Concluding only 2 address are assigned to a device.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-05-21 14:53:45 +02:00
Petr Štetiar
31ea08a64b ar71xx: ag71xx: Fix broken networking on some devices (FS#2177)
It was reported, that latest ar71xx builds have broken networking on
TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting
the offending commit, everything is back to normal.

Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
0f8cdc28af ar71xx: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Robert Marko
99f6f2c0b8 ar71xx: Add support for TP-Link CPE210 v3
Looks identical to the v2.

This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-02 02:09:58 +02:00
Koen Vandeputte
e1444ab59c ar71xx: add support for MikroTik RouterBOARD 922UAGS-5HPacD
This patch adds support for the MikroTik RouterBOARD 922UAGS-5HPacD
with a built-in 802.11ac High-Power radio (31dBm).

See https://mikrotik.com/product/RB922UAGS-5HPacD for more info.

Specifications:
- SoC: Qualcomm Atheros QCA9557 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9882 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V
- SFP: 1x host
- USB: 1x 2.0 type A
- PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems)
- SIM slot: 1x mini-SIM

Working:
- Board/system detection
- NAND storage detection
- PCIe
- USB: Type A & mini PCIe
- Wireless
- Ethernet
- LED's (excl. SFP and RSSI levels)
- Reset button
- Sysupgrade

Not working:
- SFP cage

Installation:

- Boot vmlinux-initramfs image via BOOTP/TFTP and then flash sysupgrade
image using "sysupgrade -n"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-03-26 18:01:47 +01:00
Xavier Douville
5ac974f214 ar71xx: Add support for Mikrotik RB SXT 2nD r3
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.

Hardware
--------
CPU:   Atheros AR9344 (600 MHz)
RAM:   64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH:   1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V

Installation instructions:

1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
   DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
   no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
   openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
   should be used.

Signed-off-by: Xavier Douville <github@douville.org>
2019-03-22 00:40:29 +01:00
Mantas Pucka
fe591f2fe2 ar71xx: enable QCA955x SGMII fixup on Rambutan
fixes intermittent loss of connectivity on 1Gbit port, with
log message:

  803x_aneg_done: SGMII link is not ok

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2019-03-06 22:02:56 +01:00
Koen Vandeputte
d3506d1bc1 ar71xx: ag71xx: fix compile error when enabling debug
Starting from kernel 4.5, phy_id needs to be fetched from a different location.

not doing so results in this compile error:

drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c: In function 'ag71xx_phy_connect_multi':
drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:133:35: error: 'struct mdio_device' has no member named 'phy_id'
    ag->mii_bus->mdio_map[phy_addr]->phy_id);
                                   ^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
    printk(fmt, ##__VA_ARGS__); \
                  ^~~~~~~~~~~
drivers/net/ethernet/atheros/ag71xx/ag71xx.h:72:27: note: in expansion of macro 'pr_debug'
 #define DBG(fmt, args...) pr_debug(fmt, ## args)
                           ^~~~~~~~
drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:130:3: note: in expansion of macro 'DBG'
   DBG("%s: PHY found at %s, uid=%08x\n",
   ^~~
scripts/Makefile.build:326: recipe for target 'drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.o' failed

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-05 13:19:43 +01:00
Andreas Ziegler
53c46b504c ar71xx: GL.iNet AR300M family: correct LED definitions
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2019-02-26 23:20:04 +01:00
Edoardo Scaglia
077253dd66 ar71xx: fix Arduino Yun enabling of level shifters outputs
As show in Arduino Yun schematic [1] GPIO 21 and 22 are connected to
output enable pin (OE) of two NTB01xx level shifters.

NTB01xx datasheets [2] [3] states that OE pin are active-high
therefore we should initialize GPIO 21 (DS_GPIO_OE) and GPIO 22
(DS_GPIO_OE2) accordingly to actually enable level shifters outputs.

[1] https://www.arduino.cc/en/uploads/Main/arduino-Yun-schematic.pdf
[2] https://www.nxp.com/docs/en/data-sheet/NTB0102.pdf
[3] https://www.nxp.com/docs/en/data-sheet/NTB0104.pdf

Signed-off-by: Edoardo Scaglia <edoardo.87@gmail.com>
2019-02-08 17:27:47 +01:00
Milan Krstic
39ede7bc67 ar71xx: ag71xx: preserve port mirror flags during swconfig apply
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.

This fix preserves port mirroring flags during apply.

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2019-01-22 09:05:59 +01:00
Daniel F. Dickinson
99c81eab78 ar71xx: Fix PowerCloud CR5000 5GHz wifi mac
Without this patch PowerCloud CR5000 AR9382 PCIe 5GHz Wifi uses
the mac address from eeprom instead the one specified when
initializing the PCIe chip.  There were two issues:

1) ap94_pci_init on the second PCIe wmac is wrong as there is only one
PCIe wmac on this device (the other wmac is the AR1022/AR9342 SoC wmac).
2) Without specifying pdata->use_eeprom there is a failure to load
firmware and caldata.

Thanks to Christian Lamparter (@chunkeey) for the heavy lifting and
help. [0]

[0] <https://github.com/openwrt/openwrt/pull/1613>

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-12-20 18:28:59 +01:00
Petr Štetiar
22f9afa118 ar71xx: ag71xx: Replace duplicate debugging code with simple function call
ag71xx_dump_regs is used in code several times, and is providing same
output.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:03:45 +01:00
Romain MARIADASSOU
02494fa35c
Add support for TL-WA801ND v4
This add support for TP-Link TL-WA801ND v4 (same as TL-WA801ND v3) :

Specification:

- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: 650 MHz
- Flash-Chip: Winbond W25Q32BVSIG
- Flash size: 4096 KiB
- RAM: 32 MiB
- Wireless No1: SoC-integrated: QCA9533 2.4GHz 802.11bgn

Flash instructions:

1) To flash the image, rename the file
   openwrt-ar71xx-generic-tl-wa801nd-v4-squashfs-factory.bin
   to firmware.bin
2) Connect your device to the LAN port, then upload the firmware
   through web interface. It will try to download the image and
   flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-12-07 21:46:45 +01:00
Sergey Ryazanov
8baad26d01 ar71xx: fix RouterBOARD Power LED default state
RouterBOARD(s) bootloader actully turns Power LED off just before
it starts the kernel. So we need to set the LED default status to On
instead of Keep in order to keep LED on during kernel boot.

This change fixes Power LED off during the kernel boot on the RB91x and
SXT Lite boards.

Fixes: 6cad8ee0bd ("ar71xx: keep the RouterBOARD Power LED in On state")

CC: Mathias Kresin <dev@kresin.me>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-11-26 12:05:45 +01:00
Christoph Krapp
987b961537 ar71xx: add support for UniFi-AC-Mesh-Pro
This adds the build option for UniFi AC Mesh Pro as well as
model detection for it.
The device is a hardware clone of the AC Pro.

- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 2x 1000M - POE+
- Wireless:
        2.4G: QCA9563
          5G: UniFi Chip, QCA988X compatible

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-11-26 12:05:44 +01:00
Pau Escrich
15f16bf05b ar71xx: add support for Gainstrong MiniBox V3.2
Adds MiniBox V3.2 ar71xx target (QCA99531 + QCA9887)
Info: http://oolite.cn/minibox-v3-2-qca9531-qca9887-module-pin-specification.html
Reference patch: http://oolite.cn/wp-content/uploads/2017/09/minibox_v3_cc15.05_20160325.patch
Installation: Upload firmware to uboot via HTTP at 192.168.1.1 (press button for 5 seconds)

Signed-off-by: Pau Escrich <p4u@dabax.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(daniel@makrotopia.org: rebased and fixed conflicts, fixed LED name,
                        added ath10k eeprom)
2018-11-15 19:49:51 +01:00
David Bauer
cd02d4faf9 ar71xx: flag FritzBox 4020 buttons as active low
Buttons of AVM FritzBox 4020 are incorrectly flagged as active high.

This was an oversight as RFKill button was working as expected even
with incorrectly flagged GPIO.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-09-22 19:26:26 +02:00
Michal Cieslakiewicz
2e3e0fd94c ar71xx: WNR612v2: fix kernel panic due to wrong Wifi LED init
Netgear WNR612v2 flashed with recent OpenWrt builds suffers from kernel
panic at boot during wireless chip initialization, making device
unusable:

 ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
 ath: phy0: Enable LNA combining
 CPU 0 Unable to handle kernel paging request at virtual address 1000fee1, epc == 801d08f0, ra == 801d0d90
 Oops[#1]:
 CPU: 0 PID: 469 Comm: kmodloader Not tainted 4.9.120 #0
 [ ... register dump etc ... ]
 Kernel panic - not syncing: Fatal exception
 Rebooting in 1 seconds..

This simple patch fixes above error. It keeps LED table in memory after
kernel init phase for ath9k driver to operate correctly (__initdata
removed).

Also, another bug is fixed - correct array size is provided to function
that adds platform LEDs (this device has only 1 connected to Wifi chip)
preventing code from going outside array bounds.

Fixes: 1f5ea4eae4 ("ar71xx: add correct named default wireless led by using platform leds")

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[trimmed commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-28 07:21:01 +02:00
Koen Vandeputte
6100655c8c ar71xx: fix typo in rb91x nand source
Fixes: 3b1ea0996f ("ar71xx: fix build error due to bad include")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-24 09:18:13 +02:00
Koen Vandeputte
3b1ea0996f ar71xx: fix build error due to bad include
While "rawnand.h" is available in kernel 4.14,
the default for this target is kernel 4.9 in which "nand.h" should be used.

Add an extra check to include the correct file depending on kernel version

Fixes these build errors:

drivers/mtd/nand/ar934x_nfc.c:16:10: fatal error: linux/mtd/rawnand.h: No such file or directory
 #include <linux/mtd/rawnand.h>
          ^~~~~~~~~~~~~~~~~~~~~
compilation terminated.

Fixes: 318e19ba67 ("ar71xx: add v4.14 support")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-22 13:11:59 +02:00