Commit Graph

23424 Commits

Author SHA1 Message Date
Nick Hainke
cf5a1abe46 ath79: define 2.4GHz radio for nanostation ac loco
The nanostation ac loco has a 2.4GHz management radio.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2020-10-25 16:04:52 +01:00
Nick Hainke
a181dbc2e3 ath79: fix nanostation ac loco ethernet interface
In 4.14 the delays were not cleared, so setting "rgmii" as phy-mode
did not affect delays set by the bootloader. With 5.4 kernel the
situation changed and the ethernet interface stopped working.

Just taking the ethernetpart from the litebeam ac gen2 will fix
the issue.

Explained-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2020-10-25 16:04:31 +01:00
Jianhui Zhao
63ab77d0eb ramips: mt7621: use lzma-loader for U7621-06
The U7621-06 fails to boot if the kernel is large.
Enabling lzma-loader resolves the issue.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2020-10-25 22:30:02 +08:00
Chuanhong Guo
23be410b3d ramips: add support for TOTOLINK X5000R
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 16MB (EN25QH128A)
- Ethernet: 5xGbE
- WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps

Known issue:
MT7915 DBDC variant isn't supported yet.

Flash instruction:
Upload the sysupgrade firmware to the firmware upgrade page in
vendor fw.

Other info:
MT7915 seems to have two PCIEs connected to MT7621. Card detected on
PCIE0 has an ID of 14c3:7916 and the other one on PCIE1 has 14c3:7915.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-10-25 22:27:44 +08:00
Yousong Zhou
4c21415350 generic: 5.4: make nf nat masquerade in unset state by default
Upstream linux 5.1 commit d1aca8ab ("netfilter: nat: merge ipv4 and ipv6
masquerade functionality") replaces the following 2 options

 - CONFIG_NF_NAT_MASQUERADE_IPV4
 - CONFIG_NF_NAT_MASQUERADE_IPV6

with CONFIG_NF_NAT_MASQUERADE.  The new option is one without prompt and
will be selected by CONFIG_NETFILTER_XT_TARGET_MASQUERADE introduced
still later in 5.2.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-10-24 22:28:37 +08:00
John Audia
dd20ba98e7 kernel: bump 5.4 to 5.4.72
All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2020-10-20 03:01:27 +02:00
Richard Fröhning
33b76d66d1 ramips: add support for TP-Link RE200 v4
TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas.
It's based on MediaTek MT7628AN+MT7610EN like the v2/v3.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

The MAC address assignment matches stock firmware, i.e.:

LAN : *:8E
2.4G: *:8D
5G  : *:8C

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

Instructions for serial console and recovery may be checked out in
commit 6d6f36ae78 ("ramips: add support for TP-Link RE200 v2") or on
the device's Wiki page.

Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[removed empty line, fix commit message formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-10-20 03:01:13 +02:00
Adrian Schmutzler
21cf17bb4c lantiq: remove support for kernel 4.19
The target uses 5.4 as default kernel since 06/2020.

Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed and upcoming changes (mainly DSA) will break
backward-compatibility anyway.

Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-19 15:57:40 +02:00
Ansuel Smith
f47cb405ca ipq806x: fix pci broken on bootm command
Pci is broken when bootm is used instead of the custom bootipq. This
is caused by the lack of reset by the bootloader. Make the driver do
the reset to fix this specific problem.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2020-10-19 15:46:17 +02:00
Adrian Schmutzler
29ca10e537 ipq806x: remove support for kernel 4.19
The target uses 5.4 as default kernel since 04/2020.

Kernel 4.19 support is not really maintained anymore, and there has
been a lot of changes between 4.19 and 5.4 on this target. Despite,
new devices are typically added for 5.4 only anyway.

Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-19 15:37:54 +02:00
Adrian Schmutzler
a7afeb3142 ipq40xx: remove support for kernel 4.19
The target uses 5.4 as default kernel since 03/2020.

Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed, and removing it will make upcoming driver
updates easier. Thus, remove it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-19 15:30:44 +02:00
John Crispin
c78e123d5a rtl838x: various fixes
* add d-link_dgs-1210-10p support
* make sure mips16 is disabled
* add a generic sub target
* add proper cflags

Signed-off-by: John Crispin <john@phrozen.org>
2020-10-19 14:53:27 +02:00
Jayantajit Gogoi
e6d9f6fdff sunxi: add support for FriendlyARM NanoPi R1
Specification:

- CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
- DDR3 RAM: 512MB/1GB
- Network:
    10/100/1000M Ethernet x 1,
    10/100M Ethernet x 1
- WiFi: 802.11b/g/n, with SMA antenna interface
- USB Host: Type-A x2
- MicroSD Slot x 1
- MicroUSB: for OTG and power input
- Debug Serial Port: 3Pin 2.54mm pitch pin-header
- LED:
    nanopi:red:status
    nanopi:green:wan
    nanopi:green:lan
- KEY:
    reset
- Power Supply: DC 5V/2A

Installation:

- Write the image to SD Card with dd
- Boot NanoPi from the SD Card

Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
2020-10-18 15:46:42 +02:00
张鹏
4ff7bdfeeb ath79: add support for Qxwlan E1700AC v2
E1700AC v2 based on Qualcomm/Atheros QCA9563 + QCA9880.

Specification:

 - 750/400/250 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 3T3R 2.4 GHz
 - 3T3R 5 GHz
 - 2 x 10/1000M Mbps Ethernet (RJ45)
 - 1 x MiniPCI-e
 - 1 x SIM (3G/4G)
 - 1 x USB 2.0 Port
 - 5 x LED , 2 x Button(S8-Reset Buttun), 1 x power input
 - UART (J5) header on PCB (115200 8N1)

Flash instruction:

   1.Using tftp mode with UART connection and original LEDE image
      - Configure PC with static IP 192.168.1.10 and tftp server.
      - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
        to "firmware.bin" and place it in tftp server directory.
      - Connect PC with one of LAN ports, power up the router and press
        key "Enter" to access U-Boot CLI.
      - Use the following commands to update the device to LEDE:
        run lfw
      - After that the device will reboot and boot to LEDE.
      - Wait until all LEDs stops flashing and use the router.

   2.Using httpd mode with Web UI connection and original LEDE image
      - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
      - Connect PC with one of LAN ports,press the reset button, power up
        the router and keep button pressed for around 6-7 seconds, until
        leds flashing.
      - Open your browser and enter 192.168.1.1,You will see the upgrade
        interface, select "openwrt-ar71xx-generic-xxx-squashfs-
        sysupgrade.bin" and click the upgrade button.
      - After that the device will reboot and boot to LEDE.
      - Wait until all LEDs stops flashing and use the router.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig, whitespace fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-17 20:18:00 +02:00
张鹏
987d9028e1 ath79: add support for Qxwlan E558 v2
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.

Specification:

 - 720/600/200 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4 GHz (QCA9558)
 - 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
 - 4x miniPCIe slot (USB 2.0 bus only)
 - 1x microSIM slot
 - 5x LED (4 driven by GPIO)
 - 1x button (reset)
 - 1x 3-pos switch
 - 1x DC jack for main power input (9-48 V)
 - UART (JP5) and LEDs (J8) headers on PCB

Flash instruction:

   1.Using tftp mode with UART connection and original LEDE image
      - Configure PC with static IP 192.168.1.10 and tftp server.
      - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
        to "firmware.bin" and place it in tftp server directory.
      - Connect PC with one of LAN ports, power up the router and press
        key "Enter" to access U-Boot CLI.
      - Use the following commands to update the device to LEDE:
        run lfw
      - After that the device will reboot and boot to LEDE.
      - Wait until all LEDs stops flashing and use the router.

   2.Using httpd mode with Web UI connection and original LEDE image
      - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
      - Connect PC with one of LAN ports,press the reset button, power up
        the router and keep button pressed for around 6-7 seconds, until
        leds flashing.
      - Open your browser and enter 192.168.1.1,You will see the upgrade
        interface, select "openwrt-ar71xx-generic-xxx-squashfs-
        sysupgrade.bin" and click the upgrade button.
      - After that the device will reboot and boot to LEDE.
      - Wait until all LEDs stops flashing and use the router.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig, whitespace adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-17 20:17:59 +02:00
张鹏
27a7d071c0 ath79: add support for Qxwlan E750G v8
Qxwlan E750G v8 is based on Qualcomm QCA9344 + QCA9334.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4G GHz (AR9344)
 - 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction:

   1.Using tftp mode with UART connection and original LEDE image
      - Configure PC with static IP 192.168.1.10 and tftp server.
      - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
        to "firmware.bin" and place it in tftp server directory.
      - Connect PC with one of LAN ports, power up the router and press
        key "Enter" to access U-Boot CLI.
      - Use the following commands to update the device to LEDE:
        run lfw
      - After that the device will reboot and boot to LEDE.
      - Wait until all LEDs stops flashing and use the router.

   2.Using httpd mode with Web UI connection and original LEDE image
      - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
      - Connect PC with one of LAN ports,press the reset button, power up
        the router and keep button pressed for around 6-7 seconds, until
        leds flashing.
      - Open your browser and enter 192.168.1.1,You will see the upgrade
        interface, select "openwrt-ar71xx-generic-xxx-squashfs-
        sysupgrade.bin" and click the upgrade button.
      - After that the device will reboot and boot to LEDE.
      - Wait until all LEDs stops flashing and use the router.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-17 20:17:59 +02:00
Felix Fietkau
4a0688ed71 base-files: remove block2mtd checks from sysupgrade
This hasn't been used in a long time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-10-17 16:43:17 +02:00
Felix Fietkau
93f98b2835 kernel: remove obsolete non-upstream block2mtd patches
Since block2mtd is not used for firmware images anymore, these patches
are no longer needed

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-10-17 16:43:17 +02:00
Felix Fietkau
b59d5c8f0e mediatek: rewrite flow offload code
The code is now much cleaner and works better than the old code.
Preparation for submitting it upstream (though with a different API)
Also add back MT7621 support and fix flow table coherence issues on
MT7622

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-10-16 21:37:39 +02:00
Peng Zhang
5666ca913a ath79: add support for Qxwlan E750A v4
Qxwlan E750A v4 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 5G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (one port with PoE support)
 - 1x miniPCIe slot (USB 2.0 bus only)
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction:

   1.Using tftp mode with UART connection and original LEDE image
      - Configure PC with static IP 192.168.1.10 and tftp server.
      - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
        to "firmware.bin" and place it in tftp server directory.
      - Connect PC with one of LAN ports, power up the router and press
        key "Enter" to access U-Boot CLI.
      - Use the following commands to update the device to LEDE:
        run lfw
      - After that the device will reboot and boot to LEDE.
      - Wait until all LEDs stops flashing and use the router.

   2.Using httpd mode with Web UI connection and original LEDE image
      - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
      - Connect PC with one of LAN ports,press the reset button, power up
        the router and keep button pressed for around 6-7 seconds, until
        leds flashing.
      - Open your browser and enter 192.168.1.1,You will see the upgrade
        interface, select "openwrt-ar71xx-generic-xxx-squashfs-
        sysupgrade.bin" and click the upgrade button.
      - After that the device will reboot and boot to LEDE.
      - Wait until all LEDs stops flashing and use the router.

Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[cut out of bigger patch, alter use of DEVICE_VARIANT, merge case
in 01_leds, use lower case for v4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-15 18:52:39 +02:00
Adrian Schmutzler
dec4a028ab rtl838x: remove model name from LED labels
Like in the previous patches for various targets, this removes
the "devicename" from LED labels in rtl838x, as it's useless and
only creates complexity.

Since the target is fresh and so far only system LEDs were added,
this does not add a migration script.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-15 17:54:31 +02:00
Adrian Schmutzler
a49c1aa883 rtl838x: move dts-v1 to DTSI
The syntax of the shared SoC DTSI file determines the DTS version,
so no need to repeat the "/dts-v1/;" identifier in every file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-15 17:51:42 +02:00
Adrian Schmutzler
3679f8f933 sunxi: use wpad-basic-wolfssl for Sinovoip Banana Pi M2 Ultra
The idea of commit a14f5bb4bd was to use wpad-basic-wolfssl
consistently throughout the whole trunk, so use it here as well.

Fixes: 50fdddae05 ("BPi-M2U kernel modules for onboard WiFi")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-15 17:46:54 +02:00
John Audia
0efec6a008 kernel: bump 5.4 to 5.4.71
All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711,
              lantiq/Easybox 904 xDSL
Run-tested:   ipq806x/R7800, lantiq/Easybox 904 xDSL

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test reports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-15 17:46:54 +02:00
John Crispin
479d1154c4 rtl838x: add DLink DGS-1210-16 support
Signed-off-by: John Crispin <john@phrozen.org>
2020-10-15 13:36:10 +02:00
Birger Koblitz
076fdd9fec rtl838x: Fix firmware handling
Fix wrong magic number verification for FW files.
Correct handling of external RTL8218B firmware PHY name in firmware.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-10-15 13:26:57 +02:00
Andreas Oberritter
f422488337 rtl838x: do not default to the router DEVICE_TYPE
The router profile installs many packages unnecessary for
the operation of a typical ethernet switch. Instead of creating
an empty switch profile upfront, use the basic profile until
a set of common packages crystallizes.

Signed-off-by: Andreas Oberritter <obi@saftware.de>
2020-10-15 08:32:31 +02:00
Andreas Oberritter
0c26c9395b rtl838x: bundle phy firmware with Linux kernel
Fixes long delay on boot when booting from flash. The driver waits
for one minute for userspace to load firmware, before it becomes
available.

Signed-off-by: Andreas Oberritter <obi@saftware.de>
2020-10-15 08:32:31 +02:00
Birger Koblitz
121ef9ddc9 rtl838x: Add support for RTL839x internal PHY
This adds basic support for reading the internal PHYs of the RTL839x SoCs
and full support for the 2 PHYs connected to the 1000Base-X SerDes of
the RTL8393 SoC.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-10-15 08:32:23 +02:00
Birger Koblitz
3c4063f715 rtl838x: Add irq settings for RTL839x SoCs
This adds correct interrupt routing settings for IRQs on the RTL839x SoCs.
It also speeds up irq handling based on work by biot for all SoCs.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-10-15 08:23:46 +02:00
Rui Salvaterra
e788e9bd87 treewide: enable the vDSO
The vDSO is used to accelerate some syscalls. It should work fine wherever it's
available, so enable it globally for all targets.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2020-10-13 20:08:41 +02:00
Hal Martin
0830ae3a2f sunxi: Correct manufacturer name to Sinovoip
Sinovoip is the manufacturer of the BPi-M2U:
http://www.banana-pi.org/m2u.html

Signed-off-by: Hal Martin <hal.martin@gmail.com>
2020-10-11 20:27:20 +02:00
Hal Martin
50fdddae05 sunxi: BPi-M2U kernel modules for onboard WiFi
Signed-off-by: Hal Martin <hal.martin@gmail.com>
2020-10-11 20:27:14 +02:00
Arturas Moskvinas
679db02b10 sunxi: add support for FriendlyArm Zeropi
Specification

    CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
    DDR3 RAM: 256MB/512MB
    Connectivity: 10/100/1000Mbps Ethernet
    USB Host: Type-A x 1
    MicroSD Slot x 1
    MicroUSB: for power input only
    Debug Serial Port: 4Pin, 2.54 mm pitch pin header
    Power Supply: DC 5V/2A
    PCB Dimension: 40 x 40 x 1.2mm

Installation:

    Burn the image file to an SD Card with dd or any image burning tool
    Boot ZeroPi from the SD Card

The following features are working and tested:

    Ethernet port 10/100/1000M Ethernet

Remarks: SBC is mostly compatible and boots with FriendlyARM NanoPI M1 plus DTS also (zeropi has no working hdmi)

Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
2020-10-11 18:29:26 +02:00
Andre Heider
37e62ec4ec sunxi: add a kmod package for sun4i_spdif
Tested on a A20 board:
$ cat /proc/asound/cards
 0 [SPDIF          ]: On-board_SPDIF - On-board SPDIF
                      On-board SPDIF

Size of the module for a 32bit kernel:
60708 linux-5.4.66/sound/soc/sunxi/sun4i-spdif.ko

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-10-11 17:45:02 +02:00
Andre Heider
4943d3f14b sunxi: add SND_SIMPLE_CARD to kernel config
This is required to expose an ALSA card for quite some boards:

$ git grep -l simple-audio-card \
	arch/arm/boot/dts/sun?i* \
	arch/arm64/boot/dts/allwinner/*

arch/arm/boot/dts/sun4i-a10-a1000.dts
arch/arm/boot/dts/sun5i-gr8-evb.dts
arch/arm/boot/dts/sun6i-a31-i7.dts
arch/arm/boot/dts/sun6i-a31s-sina31s.dts
arch/arm/boot/dts/sun7i-a20-cubietruck.dts
arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
arch/arm/boot/dts/sun8i-a33-olinuxino.dts
arch/arm/boot/dts/sun8i-a33.dtsi
arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts

The compressed 32bit kernel increases less than 1K:
Before: 3230768 zImage
After:  3231664 zImage

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-10-11 17:45:02 +02:00
Andre Heider
c43b45863e mvebu: Add bootscript for espressobin to support mainline firmware
The generic bootscript is tailored around a downstream firmware and
doesn't work on a firmware built from mainline components.

Add a bootscript which:
* sets $console since mainline u-boot doesn't do that
* uses distro boot variables, so OpenWRT can be booted off any supported
  device when using a mainline firmware
* sets missing distro boot variables for the downstream firmware

Booting with a downstream firmware is unchanged.
Booting with a mainline firmware now works.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-10-11 16:53:20 +02:00
Hauke Mehrtens
722906d144 kernel: move CONFIG_F2FS_CHECK_FS to generic kernel config
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-10-11 16:38:16 +02:00
Hauke Mehrtens
6542615e41 kernel: Move CONFIG_F2FS_FS_SECURITY to generic kernel config
Move the CONFIG_F2FS_FS_SECURITY kernel configuration option to the
generic kernel configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-10-11 16:38:16 +02:00
Hauke Mehrtens
18deed29be kernel: Remove 2FS_FS_XATTR and F2FS_STAT_FS symbols from target configs
This config option was moved to the generic kernel configuration.

Fixes: ab1bd57656 ("kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-10-11 16:38:16 +02:00
Kabuli Chana
4d6ade2a22 mvebu: Correct regulatory country of WRT3200ACM
correct oversight on setting regulatory country and mac address of wireless configuration
change method of retrieving mac address

The MAC address for eth0 is rad out of the devinfo partition in some
other initial configuration script already.

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2020-10-11 16:38:03 +02:00
Kabuli Chana
c5bd4dde32 mvebu: add wrt3200acm to 03_wireless CC
correct device CC oversight

Set the initial wifi configuration like for the other similar Linksys
devices.

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2020-10-11 16:23:39 +02:00
Pali Rohár
9948c19134 mvebu: armada-37xx: espressobin: Backport patch for ethernet switch aliases
Signed-off-by: Pali Rohár <pali@kernel.org>
2020-10-11 16:16:24 +02:00
Pali Rohár
eb777539fd mvebu: armada-37xx: Backport PCI aardvark patches
This commit contains patches for PCI aardvark driver and relevant DTS
changes for Turris MOX and EspressoBin backported from mainline kernel.
It fixes support for old ATF, various wifi cards, mainly Compex WLE900VX.

Signed-off-by: Pali Rohár <pali@kernel.org>
2020-10-11 16:16:24 +02:00
Tony Ambardar
1b27591ddb malta: update MIPS64 ISA to R2
Usage of current R1 ISA is inconsistent with the MIPS32 subtarget, little
used and has limited utility for testing.

Many distros target a minimum R2 ISA. Debian MIPS 32-bit/64-bit ports all
use MIPS R2 ISA since Stretch, for example. Fedora's MIPS arch also targets
the R2 ISA for 32-bit/64-bit.

Widely used MIPS64 platforms like Octeon are based on the MIPS R2 ISA or
later, and benefit from having a compatible test platform in OpenWRT.

While Linux does support MIPS64 R1 targets, its usefulness for development
and testing is limited. As an example, the modern Linux eBPF JIT requires
a MIPS R2 ISA or later.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[Refresh config and fix README]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-10-11 16:16:24 +02:00
Adrian Schmutzler
c98819a9e6 bcm63xx: move dts-v1 statement to top-level DTSI files
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.

Like done for other targets recently, put the dts-v1 statement
into the top-level SoC-based DTSI files, and remove all other
occurences.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-10 20:00:34 +02:00
Adrian Schmutzler
c0aea38436 bcm63xx: add a few DTSI files to share definitions
After the LED labels have been made more general by removing
the model names, we can move several definitions to DTSI files
to reduce the amount of duplicate code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-10 19:55:18 +02:00
Adrian Schmutzler
55aac8463f bcm63xx: remove model name from LED labels
Like in the previous patches for various targets, this will remove
the "devicename" from LED labels in bcm63xx, as it's useless and
only creates complexity.

The devicename is removed in DTS files and 01_leds, merging
several cases on the way. A migration script is added for
existing configurations.

Note that a few labels were using "model::function" scheme without
color specified, those were converting to just "function" and the
necessary migrations were added to the migration script.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-10 19:44:02 +02:00
Daniel Golle
5423d9d27e kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-10-09 23:20:19 +01:00
Adrian Schmutzler
f2b952a657 ath79: drop redundant gpios on i2c
Since "sda-gpios" and "scl-gpios" are only available since kernel 4.19,
a few devices have redundantly defined "gpios" to also support older
kernels. Since we have nothing older than 4.19 now, we can remove
the redundant definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-09 22:45:36 +02:00