The nf_reject_* and nf_nat_masquerade_* modules are moved into the
corresponding kmod-nf- packages. Appropriate dependencies are added to the
kmod-nft- packages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Forgot to update kernel-version.mk, so updated patch. Compile-tested on x86/64 and ar71xx; run-tested on x86/64 and ar71xx.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
-add spi pins
-move mdio and rgmii pinctrl from gmac and mdio into pinmux node
-add i2c4 pinctrl into rpm node
-add pin details into several nodes
-update gmac1 and gmac2 parameters
-update mdio phy0 and phy4 registers by ddwrt devs findings
-fix i2c4 pin drive-strengh
-remove pcie pins as it's already present in ipq8065 DT
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Now that the firmware for BCM43430 has been submitted to linux-firmware use it
and remove RPiDistro package.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add patches for SFP support and package it for ClearFog. Tested with a
Juniper SFP module.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
MSI interrupts do not seem to be working on mvebu, and they break
ath10k. Since nothing else seems to be using them, especially not
mwlwifi, disable them until we can fix MSI interrupts.
Works around the following issue:
[ 9.001457] ath10k_pci 0000:02:00.0: failed to receive control response completion, polling..
[ 10.001453] ath10k_pci 0000:02:00.0: Service connect timeout
[ 10.007126] ath10k_pci 0000:02:00.0: failed to connect htt (-110)
[ 10.092224] ath10k_pci 0000:02:00.0: could not init core (-110)
[ 10.098177] ath10k_pci 0000:02:00.0: could not probe fw (-110)
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
ar71xx has an init-script for special devices where the ath10k OTP
calibration data is stored on the PCIe card's EEPROM (and thus can only
be read by ath10k). Unfortunately the OTP data uses the default mac
address (= all devices come with the same mac address, which leads to
problems when you have multiple of these devices in the same network).
To work around this the mac address is patched in the firmware during
the first boot of the device. To prevent flash wear this was only done
if the ath10k firmware matched a hardcoded md5sum.
However, if the md5sum does not match this can mean that either the mac
address was already patched (which is fine) - unfortunately it can also
mean that the firmware version was updated without updating the
hardcoded md5sum.
Change the "was the mac address already patched" check to actually
compare the mac address inside the ath10k firmware.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on
kmod-cfg80211. kmod-rt2800-pci should not be installed anyways.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add and enable sysupgrade support for clearfog boards, based on how the
brcm2708 target does it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Add a switch node to clearfog to probe and initialize it on Clearfog
Pro. This make the switch work and allows using all six switch ports.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
If the cpu port is connected through SGMII we need to enable SerDes for
it to work.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
The clearfog u-boot does not initialize the switch at all, so we need to
power up the phys ourselves.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Make the dts file match with what is upstream, to ensure it has the
latest changes and switching to newer kernels is easier.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Some of the PCIe and USB signals use a GPIO expander on I2C on ClearFog,
so enable the driver so that they can be configured to their required
values.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Uboot-mvebu isn't a real package, which will break the image builder
when it tries to install it during the packing step. Instead of cleafog
selecting it through its default packages, make it default to m if the
clearfog profile is selected.
This will ensure it is always build, but never added to the rootfs. This
fixes creating images for clearfog with IB.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
The clearfog image requires u-boot, so package it into KDIR to make sure
it is available in imageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Some devices (like the Cisco Meraki Z1 Cloud Managed Teleworker Gateway)
need to be able to initialize the PCIe wifi device. Normally, this is done
during the early stages of booting linux, because the necessary init code
is read from the memory mapped SPI and passed to pci_enable_ath9k_fixup.
However,this isn't possible for devices which have the init code for the
Atheros chip stored on NAND in an UBI volume. Hence, this module can be
used to initialze the chip when the user-space is ready to extract the
init code.
Martin Blumenstingl made a few fixes and added support for lantiq:
kernel: owl-loader: add support for OWL emulation PCI devices
kernel: owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
kernel: owl-loader: use dev_* instead of pr_* logging functions
kernel: owl-loader: auto-generate the eeprom filename as fallback
kernel: owl-loader: add a debug message when swapping the eeprom data
kernel: owl-loader: add missing newlines in log messages
kernel: owl-loader: add support for the lantiq platform
These patches have been integrated. Thanks!
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
General convention is to keep U-Boot and radio calibration
data (ART) mtd partitions marked as read-only.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This changes the sysupgrade format. To support upgrades from the old
firmware to the new one, legacy images are provided. Because of the old
partition split, these have to be specific to the NOR or SPI device.
The new sysupgrade images are suitable for begin put on flash directly,
and they are independent of NOR vs SPI flash variant.
Flashing back to old firmware is supported via using the old full-flash
images instead of the old sysupgrade images.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are currently two stock firmwares for the TL-WDR3600/4300, a US and
a universal version. Both allow installing images with US region code, so
we don't need to provide multiple images.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
