It's a simple typo in the DNS file, which was pretty serious.
No scripts were working properly. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[integrate upstream patch into openwrt target]
This adds the dm-raid kmod, which is needed for
LVM builtin raid configurations, aka "MD-over-LVM"
Signed-off-by: Chris Koying Browet <cbro@semperpax.com>
Support to disable the timestamp check for certificates in
wpa_supplicant (Useful for devices without RTC that cannot
reliably get the real date/time) has been accepted in the
upstream hostapd. It's implemented in wpa_supplicant as a
per-AP flag tls_disable_time_checks=[0|1].
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
bnx2x driver support for the x86 architecture. Includes module and
firmware for Broadcom QLogic 5771x/578xx 10/20-Gigabit ethernet
adapters.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added +kmod-lib-zlib-inflate as well]
When OEM volumes are present in the [alt_]firmware partition,
sysupgrade will write a new kernel, but will fail to write
the root file system. The next boot will hang indefinitely
Waiting for root device /dev/ubiblock0_0...
Modified ipq40xx/base-files/lib/upgrade/linksys.sh
to remove both `squashfs` and `ubifs` if found
on the target firmware partition's UBI device.
Run-tested-on: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[applied some shellcheck suggestions as well]
This patch adds a missing type property. This fixes
the creation of oneshot and timer led triggers like:
| ucidef_set_led_timer "system" "system" "zhuotk:green:system" "1000" "1000"
from /etc/init.d/01_leds.
Fixes: b06a286a48 ("base-files: cleanup led functions in uci-defaults.sh")
Signed-off-by: Robinson Wu <wurobinson@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
"There are often transient line events when
the system is powered up and initialized and it
is often necessary for the gpio_chip driver to
clear any interrupt flags in hardware before
setting up the gpio chip, especially the
irqchip portions of it."
<http://lists.infradead.org/pipermail/openwrt-devel/2019-June/017630.html>
This patch adds a fix for the APM821XX's interrupt
controller to clear any bogus pending toggled
interrupts that happens on various APM821XX boards
on boot.
The patch also changes the debouce-interval from the
default 5ms debounce interval to 60ms all around.
The default setting caused on occasions that the button
state became stuck in a pressed state, even though the
button was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefor add all libraries linked by uhttpd
as direct dependencies to the corresponding binary package definition.
This ensures that uhttpd is automatically rebuilt and relinked if any
of these libraries has its ABI_VERSION updated in the future.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Makefile was missing dependencies on *c_shipped, so changes never
triggered a rebuild. Add these as optional dependencies so their absence
isn't treated as an error.
In addition, fix a typo preventing the zconf.lex.o from being removed on
clean.
Fixes: 9d5510a500 ("build: add new menuconfig code based on linux 3.9")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
calc_vmlinuz_load_addr.c requires SZ_64K to be defined for alignment
purposes. It included "../../../../include/linux/sizes.h" to define
that size, however "sizes.h" tries to include <linux/const.h> which
assumes linux system headers. These may not exist eg. the following
error was encountered when building Linux for OpenWrt under macOS:
In file included from arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:16:
arch/mips/boot/compressed/../../../../include/linux/sizes.h:11:10: fatal error: 'linux/const.h' file not found
Change makefile to force building on local linux headers instead of
system headers. Also change eye-watering relative reference in include
file spec.
Thanks to Jo-Philip Wich & Petr Štetiar for assistance in tracking this
down & fixing.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When there are multiple packages providing a meta-package, it is
possible to to create a config where a package is selected as =y, but
all of its dependency providers are just selected as =m. This is due to
the selection statement being just
config PACKAGE_foo
select PACKAGE_bar if !PACKAGE_baz
which is already fulfilled by PACKAGE_bar=m. Fix this by properly
comparing the selection states:
config PACKAGE_foo
select PACKAGE_bar if PACKAGE_baz<PACKAGE_foo
Also invert the select conditions to improve readability.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[slightly reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
After commit e82a4d9cfb ("config: regenerate *_shipped sources") the mconf
parser became more strict as a side effect and started to spew a series of
warnings when evaluating our generated kconfig sources:
tmp/.config-package.in:705:warning: ignoring unsupported character '@'
The root cause of these warnings is a wrong use of the @SYMBOL dependency
syntax in various Makefile. Fix the corresponding Makefiles by turning
`@SYM||@SYM2` expressions into the proper `@(SYM||SYM2)` form.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since commit 31847b67bec0 ("kconfig: allow use of relations other than
(in)equality") it is possible to use relational operators in Kconfig
statements. However, those operators give unexpected results when
applied to bool/tristate values:
(n < y) = y (correct)
(m < y) = y (correct)
(n < m) = n (wrong)
This happens because relational operators process bool and tristate
symbols as strings and m sorts before n. It makes little sense to do a
lexicographical compare on bool and tristate values though.
Documentation/kbuild/kconfig-language.txt states that expression can have
a value of 'n', 'm' or 'y' (or 0, 1, 2 respectively for calculations).
Let's make it so for relational comparisons with bool/tristate
expressions as well and document them. If at least one symbol is an
actual string then the lexicographical compare works just as before.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[rebased against OpenWrt kconfig, slightly reword commit message]
(backported from upstream 9059a3493efea6492451430c7e2fa0af799a2abb)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The pregenerated `zconf.hash.c` and `zconf.lex.c` files have not been
kept in sync with their respective `*.y` and `*.l` sources in the past
causing our kconfig implementation to not recognize important kconfig
grammer elements such as relational `<`, `<=`, `>` and `>=` operators.
Fixes: 2d7e602381 ("scripts/config: sync with latest linux upstream")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefor add all libraries linked by procd
as direct dependencies to the corresponding binary package definition.
This ensures that procd is automatically rebuilt and relinked
if any of these libraries has its ABI_VERSION updated in the
future.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes lower case AC in the DTS model name.
Fixes: 88f7a29f99 ("ramips: add support for Edimax EW-7476RPC / EW-7478AC")
Reported-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Upstream commit 6d4cd04 changes how the internal delays of the AR803x
based PHYs are enabled. With this commit, all internal delays are
disabled on driver probe and enabled based on the 'phy-mode' property in
the device-tree.
Before this commit, the RX delay was always enabled upon soft-reset
while the TX delay retained it's previous state. A hard reset enabled
the RX delay while the TX delay was disabled.
Because of this inconsistency, wrongly specified PHY-modes were working
correctly while the hardware was in a different state.
Fix the PHY-modes of some affected devices (and clean up misplaced
properties along the way) to keep the devices working flawlessly with
kernels >= 5.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch fix and enable GELAN port in D-LINK DWR-118-A2.
Tested-by: Richard Toth <trtk1992@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
In some boards is requred to change the ephy mdio base address.
This patch add of property "mediatek,ephy-base-address" in gsw
part, which allows to change ephy base address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed indentation in header file]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The port initialisation is based on assumption that phy address and
port number is the same. SoC allow different numbers and some board
have it.
Use phy address instead the port number to make sure that correct
addresses are polled.
In situation when only one PHY with address 0x0 is conected to
port 4, autopolling is broken.
This patch make autopolling correct when port number and phy address
are different.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The phy handling code forces a phy mdio address and the switch port to
which a phy is attached to be the same. Albeit such a configuration is
used for most boards, it isn't for all.
Pass the switch port number to the ethernet phy connect functions, to
ensure the correct list entry is edited and not the list entry that
matches th phys mdio address.
Use the mdio address with mdiobus_get_phy instead of the port number,
to make sure the expected ethernet phy gets connected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The whole logic in fe_phy_connect() is based on the asumption that mdio
address and switch port id are equal. Albeit it is true for most
boards, it doesn't is for all.
It isn't yet clear which subtargets/boards require the devicetree less
ethernet phy handling. Hence change the code in a way that it doesn't
touch ethernet phys which were early attached and are already handled.
Signed-off-by: Mathias Kresin <dev@kresin.me>
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN)
USB: Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header)
BTN: Reset/WPS
LED: - Power (white)
- Internet (blue)
- Wifi (blue)
- USB (blue)
UART: UART is present as Pads with throughholes on the PCB. They are
located in the lower right corner (GbE ports facing up)
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimax.setup)
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflicts in 01_leds and mt7620.mk, dts whitespace issues]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp
ramips: add Edimax EW-7478AC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6
The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflict in 01_leds]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Not all versions of ESPRESSObin require SD card, but can
be booted from the internal emmc flash (mmc dev 1) instead.
Add a simple check in the bootscript to see which mmc device
is detected and boot from it using mmcdev variable.
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Lets bump kernel to 4.19 on targets which were run tested or got ACKed
so we've enough time to make it ready for next release:
armvirt/32 (runtested in qemu)
armvirt/64 (runtested in qemu)
ath79/generic (runtested on Carambola2)
gemini/generic (runtested on DIR-685, DNS-313, SQ201, SL93512R)
imx6/generic (runtested on Apalis)
ipq40xx/generic (runtested on nbg6617)
malta/be64 (runtested in qemu)
malta/be (runtested in qemu)
malta/le (runtested in qemu)
malta/le64 (runtested in qemu)
mpc85xx/generic (runtested on TL-WDR4900)
mpc85xx/p2020 (runtested on P2020RDB)
mvebu/cortexa53
mvebu/cortexa72
mvebu/cortexa10
octeon/generic (runtested on EdgeRouter Lite)
sunxi/cortexa53 (build tested only)
sunxi/cortexa7 (runtested on Lime2-K)
sunxi/cortexa8 (build tested only)
tegra/generic
x86/64 (runtested in qemu)
Acked-by: Zoltan HERPAI <wigyori@uid0.hu> [sunxi]
Tested-by: Linus Walleij <linus.walleij@linaro.org> [gemini]
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [mvebu, tegra]
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [octeon]
Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [mpc85xx/generic mpc85xx/p2020]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following kernel build issue on ath79/generic:
Enable support for latency based cgroup IO protection (BLK_CGROUP_IOLATENCY) [N/y/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's just copy of 4.14 and will be refreshed in the upcoming commit,
renamed config-default to config-4.14 as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Refreshed all patches.
Fixes:
- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477
Also fix a malformed patch issue caught during refresh.
It was caused by removing a whitespace without altering
the index values in a patch which alters a patch.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Fixes: cf65262492 ("kernel: bump 4.19 to 4.19.51")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Altered patches:
- 370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch
- 220-optimize_inlining.patch
- 640-netfilter-nf_flow_table-add-hardware-offload-support.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (78ee6b1a40)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Refreshed all patches.
Altered patches:
- 220-optimize_inlining.patch
- 816-pcie-support-layerscape.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (78ee6b1a40)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Lets make it really explicit, that we should now focus only on ath79 in
order to make it ready for next release, where ar71xx is going to be
removed for good.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Move all MikroTik devices to new function to increase script execution
speed.
Machine name in new version of MikroTik RouterBOARD devices add "RB"
before model name:
Old machine name: MikroTik RouterBOARD 951Ui-2nD
New: MikroTik RouterBOARD RB951Ui-2nD
So this patch should fix it for all currently supported MikroTik boards.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[rebased,commit message facelift,script fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[spotted missing 922UAGS-5HPacD]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
While testing 4.19 build on malta/be64, I've encountered following
error:
gpio-button-hotplug/gpio-button-hotplug.c:529:18: error: implicit
declaration of function 'gpio_to_desc'
which is caused by the missing include fixed by this patch.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
[added sfp related patches from Russell King]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
[rebase; rework patches; separate and cleanup kernel configs;
add espessobin dts; adjust venom dts]
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Supports EIP97 and EIP197 found on Armada 37xx, 7k and 8k SoCs.
Unfortunately firmware for EIP197 is not easily obtainable, therefore
to not cause lot of user requests directed at OpenWrt, package it as
module with explanation where to obtain the firmware.
Cc: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
It's needed for applying some hardware quirks. This fixes:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/dmi.c:60:20: error: 'DMI_PRODUCT_SKU' undeclared here (not in a function); did you mean 'DMI_PRODUCT_UUID'?
DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "T8"),
Fixes: 8888cb725d ("mac80211: brcm: backport remaining brcmfmac 5.2 patches")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>