Hardware
--------
CPU: Mediatek MT7621
RAM: 256M DDR3
FLASH: 128M NAND
ETH: 1x Gigabit Ethernet
WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC)
BTN: 1x Reset (NWA50AX only)
LED: 1x Multi-Color (NWA50AX only)
UART Console
------------
NWA50AX:
Available below the rubber cover next to the ethernet port.
NWA55AXE:
Available on the board when disassembling the device.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
If the currently installed image is started from Slot A, the device will
flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case
and the device will return to the ZyXEL firmware upon next boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP
-----------------
This installation routine is especially useful in case
* unknown device password (NWA55AXE lacks reset button)
* bricked device
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to owrt.bin
$ atnf owrt.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd10 get-status
$ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd10 set-active-image 0
Copy the OpenWrt ramboot-factory image to the device using scp.
Write the factory image to NAND and reboot the device.
$ mtd write ramboot-factory.bin firmware
$ reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds a simple AES-128-CBC encryption/decryption program using
either wolfSSL or OpenSSL as backend to decrypt Arcadyan WG4xx223
configuration partitions. The ipk size is 3,355 bytes.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
moves and extends the current facilities, which have been
added some time ago for the the usbip utility, to support
more utilites that are shipped with the Linux kernel tree
to the SDK.
this allows to drop all the hand-waving and code for
failed previous attempts to mitigate the SDK build failures.
Fixes: bdaaf66e28 ("utils/spidev_test: build package directly from Linux")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The spidev_test is build in phase2 even though it should be disabled.
My best guess is that we hit the same issue that I had with nu801.
The build-system thinks it's a tool that is necessary for
building the kernel.
In this case, the same fix (adding a dependency on the presence of
the module) could work in this case as well?
Fixes: bdaaf66e28 ("utils/spidev_test: build package directly from Linux")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Disable lz4 and lzo2 manually.
Fixes errors in the form of:
Package f2fsck is missing dependencies for the following libraries:
liblz4.so.1
liblzo2.so.2
Fixes: 8b9e806160 ("f2fs-tools: update to 1.15.0")
Acked-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add patches:
- 100-configure.ac-fix-AC_ARG_WITH.patch
Remove upstreamed patches:
- 200-resize_f2fs-fix_wrong_ovp_calculation.patch
Changelog:
64f2596 f2fs-tools: upgrade version 1.15.0
d9d5b11 f2fs-tools: build silently
299c0b5 fsck.f2fs: fix broken file_map output
3af62be f2fs-tools: show segment/section layout correctly
4d9c009 f2fs-tools: use android config only if there's no config.h
0b9b89f dump.f2fs: compress: fix dstlen of LZ4_compress_fast_extState()
eee3969 mkfs.f2fs: check uuid library
e5fe1a2 f2fs-tools: use fsync() in Android
ea9921f f2fs-tools: support zoned device in Android
a8fefc2 android_config.h: add missing liblz4
0c54cf7 libf2fs_io: add unused mactor to avoid build failure
6eebd13 ci: Enable -Wall, -Wextra and -Werror
c491657 Fix PowerPC format string warnings
70e4139 Suppress a compiler warning about integer truncation
7a1206a Annotate switch/case fallthrough
b964b79 Change #ifdef _WIN32 checks into #ifdef HAVE_.*
28de4d1 tools/f2fs_io: Fix the type of 'ret'
fdff1ab fsck/segment.c: Remove dead code
ede3bde fsck/main.c: Suppress a compiler warning
93c6483 tools/f2fscrypt.c: Fix build without uuid/uuid.h header file
559e60e fsck: Remove a superfluous include directive
98f7f56 mkfs/f2fs_format.c: Suppress a compiler warning
ef011a4 configure.ac: Detect selinux/android.h
2e59ab8 configure.ac: Detect the sparse/sparse.h header
1790203 Fix the MinGW build
ecd27dc Use %zu to format size_t
24663b6 Include <stddef.h> instead of defining offsetof()
cdefef0 Move the be32_to_cpu() definition
1612bf9 Remove unnecessary __attribute__((packed)) annotations
7a5109f f2fs_fs.h: Use standard fixed width integer types
e61203c Suppress a compiler warning
9425b47 Verify structure sizes at compile time
006bb13 Change one array member into a flexible array member
cb4c5d6 ci: Build f2fstools upon push and pull requests
f3033fb Change the ANDROID_WINDOWS_HOST macro into _WIN32
87d7a95 Switch from the u_int to the uint types
c483354 configure.ac: Enable cross-compilation
3e97d07 configure.ac: Sort header file names alphabetically
91ba5e5 configure.ac: Enable the automake -Wall option
ae65a15 configure.ac: Remove two prototype tests
d24fd5c configure.ac: Stop using obsolete macros
6afcf64 libf2fs: don't allow mkfs / fsck on non power-of-2 zoned devices
c7757ec man: update mkfs.f2fs to give the default android option
46e1b83 f2fs-tools: use proper 64bit types for PPC
97ce230 mkfs.f2fs: fix wrong indentation and clean up
0d3d26d mkfs.f2fs: set project quota by default for -g android for v4.14+
1de1db8 f2fs-tools: add atomic write related options to f2fs_io write command
85cd72a mkfs.f2fs: set required quota types only
028af9f fsck.f2fs: Add progression feedback
972d710 fsck.f2fs: do not assert if i_size is missing i_blocks in symlink
f63551b f2fs-tools: separate other bugs in fsck_verify
ade81b9 f2fs-tools: remove false failure alarm when fixing quota
99bc497 f2fs-tools: fall back to the original version check when clock_gettime is not supported
1603a3d mkfs.f2fs: wipe other FS magics given -f
63d5004 fsck.f2fS: is_valid_summary(): check whether offset is out of bounds
3fd996c Avoid redefined ALIGN_UP
1edc138 fsck.f2fs: Update the usage about option of preen mode
49159df f2fs-tools: change fiemap print out format
8bcb58e f2fs_io: add rename w/ fsync option
9429e86 fsck.f2fs: add basic compress related check/fix
529967e f2fs-tools: make fiemap command in accordance with uapi
1228009 f2fs-tools: rebuild the quota inode if it is corrupted
9ee091e f2fs-tools: add periodic check in kernel version check
1bc7658 dump.f2fs: minor clean ups
69952e3 f2fs-tools: fix wrong value of reserve_new_block parameter in page_symlink
76d2a91 f2fs-tools: add extent cache for each file
8d464ee f2fs-tools: fix wrong file offset
acd2518 fsck|dump.f2fs: add -M to get file map
027488e mkfs.f2fs: remove android features for RO
e01ad31 f2fs-tools: fix metadata region overlap with zoned block device zones
f3b93bf sload.f2fs: Reword "IMMUTABLE" in strings/comments
820b5e3 sload.f2fs: use F2FS_COMPRESS_RELEASED instead of IMMUTABLE bit
1d2683f f2fs-tools: support small RO partition
a9594c6 fsck.f2fs: add "-l" to show the layout information
38e3115 f2fs_io: add to show immutable bit
6afd3e9 tools: Introduce f2fslabel
3218ff9 f2fs-tools: correct get kernel version logic
19d49b5 dump.f2fs: fix memory leak caused by dump_node_blk()
15d4d7b fsck.f2fs: fix memory leak caused by fsck_chk_orphan_node()
1900c22 mkfs.f2fs: fix memory leak in not enough segments error path
5cc365c resize.f2fs: fix memory leak caused by migrate_nat()
870915f f2fs_io: split definition check for crypto ioctl
91f9db2 fsck.f2fs: update kernel version in superblock on forced check
1531853 f2fs_io: Add get file name encryption mode
3bfcca8 f2fs-tool: increase debug level from 0 to 1 in migrate_block
5263ae2 resize.f2fs: fix to check free space before shrink
159752d resize.f2fs: fix wrong sit/nat bitmap during rebuild_checkpoint()
98e6463 resize.f2fs: add force option to rewrite broken calculation
f056fbe resize.f2fs: fix wrong ovp calculation
80dba0f Add -P option to preserve file owner
f0fda11 libf2fs: fix memory leak caused by get_rootdev()
5144f2f mkfs.f2fs: add VM disk files to hot data types
73c0871 libzoned: use blk_zone_v2 and blk_zone_report_v2 by default
9cb5150 f2fs-tools: fix wrong blk_zone_rep_v2 definition
15474db mkfs.f2fs: allocate zones together to avoid random access
316e128 mkfs.f2fs: adjust zone alignment when using multi-partitions
cc57f2c fsck.f2fs: fix alignment on multi-partition support
ff7172e f2fs-tools: Miscellaneous cleanup to README.
2b26417 mkfs.f2fs.8: Better document the -g argument.
e05afe5 mkfs.f2fs.8: fix formatting for -l parameter in man page
747b74c f2fs-tools: Make sload.f2fs reproduce hard links
b585244 f2fs-tools:sload.f2fs compression support
7b63f7b f2fs_io: add compress/decompress commands
457392a f2fs-tools: Added #ifdef WITH_func
d322d47 f2fs-tools: fix a few spelling errors in f2fs-tools
fcd5cd0 f2fs-tools: skipped to end on error syntax error
31d30f0 mkfs.f2fs: show a message when compression is enabled
1d4c7e7 f2fs_io: add get/set compression option
4bd7008 Fix ASSERT() macro with '%' in the expression
ca0ed8a f2fs-toos: fsck.f2fs Fix bad return value
c954e7c fsck.f2fs: do xnid sanity check only during fsck
1bfc173 f2fs_io: add erase option
e59bb17 mkfs.f2fs.8: document the verity feature
8fd836f fsck: clear unexpected casefold flags
1a7415a mkfs.f2fs: add -h and --help
717d70d f2fs_io: change fibmap to fiemap
Signed-off-by: Nick Hainke <vincent@systemli.org>
Compiles faster, is PIC by default, and does not have pkgconfig files
with wrong paths.
Add various fixes to it as it seems cross compilation was never tested.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Refreshed patches:
- 100-cross_compile.patch
Manually refreshed patches:
- 200-reduce_size.patch
Removed patches:
- 101-mdadm.h-Undefine-dprintf-before-redefining.patch
- 102-Add-missing-include-file-sys-sysmacros.h.patch
Changes:
e30ca260 Release mdadm-4.2
8c80d305 Monitor: print message before quit for no array to monitor
ced5fa8b mdadm: block creation with long names
b71de056 Correct checking if file descriptors are valid
b2e4f084 Incremental: Close unclosed mdfd in IncrementalScan()
195d1d76 imsm: assert if there is migration but prev_map doesn't exist
75f3ba25 imsm: free allocated memory in imsm_fix_size_mismatch
bce0eab3 Release mdadm-4.2-rc3
4389ce73 imsm: introduce helpers to manage file descriptors
8e1a258e mdadm/Detail: Can't show container name correctly when unpluging disks
a35aa68f mdadm/lib: Define a new helper function is_dev_alived
1c66260d Fix 2 dc stream buffer
d64a37b9 Assemble: apply sysfs rules
5f6dedfb Fix potential overlap dest buffer
a0422106 disallow create or grow clustered bitmap with writemostly set
cf16a350 Fix buffer size warning for strcpy
60815698 Refactor parse_num and use it to parse optarg.
f7889e51 Fix error message when creating raid 4, 5 and 10
54604768 mdadm: fix coredump of mdadm --monitor -r
feeb2785 Utils: Change sprintf to snprintf
b8bbf264 Release mdadm-4.2-rc2
e6878148 Assemble: skip devices that don't match uuid instead of aborting the assembly.
0663137c Add monitor delay parameter to mdadm.conf
2b2c5668 tests: Avoid passing chunk size when creating RAID 1
7d374a18 Fix memory leak after "mdadm --detail"
92a647c8 Assemble: start dirty and degraded array.
1c275381 imsm: fix num_data_stripes after raid0 takeover
5b30a34a Add error handling for chunk size in RAID1
3a85bf0e imsm: Fix possible memory leaks and refactor freeing struct dl
ccd61ebf mdadm: Fix building errors
601ffa78 Don't associate spares with other arrays during RAID Examine
8d69bf14 Remove Spare drives line from details for external metadata
7d8935cb imsm: correct offset for 4k disks in --examine output
dca80fcd Use dev_open in validate geometry container
f421731c mdadm/super1: It needs to specify int32 for bitmap_offset
1f5d54a0 Manage: Call validate_geometry when adding drive to external container
8662f92d imsm: Limit support to the lowest namespace
fcebeb77 imsm: add devpath_to_char method
7c798f87 imsm: add generic method to resolve "device" links
0530e2e0 Prevent user from using --stop with ambiguous args
83b3de77 Fix some building errors
ff904202 imsm: change wrong size verification
c11b1c3c Release mdadm-4.2-rc1
aec01630 super-intel.c: Handle errors from calls to get_dev_sector_size()
78c93b00 mdadm: fix growing containers
af3396da Monitor: make libudev dependency optional
f94df5cf imsm: support for third Sata controller
d835518b imsm: nvme multipath support
4036e7ee imsm: extend curr_migr_unit to u64
bdbe7f81 Grow: Block reshape when external metadata and write-intent bitmap
848d71c9 Create: Block automatic enabling bitmap for external metadata
19ad203e imsm: Update-subarray for write-intent bitmap
dc95f821 Add "bitmap" to allowed command-line values
69d40de4 imsm: Adding a spare to an existing array with bitmap
fbc42556 imsm: Write-intent bitmap support
b554ab5c Enable bitmap support for external metadata
b090e910 Modify mdstat parsing for volumes with the bitmap
db537788 It should be FAILED when raid has not enough active disks
c7b8547c imsm: add verbose flag to compare_super
49b69533 mdmonitor: check if udev has finished events processing
0d583954 Document PPL in man md
2f86fda3 imsm: use saved fds during migration
f7a6246b super1.c: avoid useless sync when bitmap switches from clustered to none
e6561c4d super1: fix Floating point exception
8818d4e7 Grow: be careful of corrupt dev_roles list
4ae96c80 mdadm: fix reshape from RAID5 to RAID6 with backup file
1fe2e100 mdadm/bitmap: locate bitmap calcuate bitmap position wrongly
75562b57 Dump: get stat from a wrong metadata file when restoring metadata
69068584 Incremental: Remove redundant spare movement logic
a64f1263 udev: start grow service automatically
b4a5ad49 Make target to install binaries only
9c030dad mdadm/Detail: show correct state for clustered array
ff6bb131 mdadm: Unify forks behaviour
a8f3cfd5 imsm: limit support to first NVMe namespace
ca4b156b Monitor: don't use default modes when creating a file
b65c1f4a imsm: remove redundant calls to imsm_get_map
895ffd99 imsm: update num_data_stripes according to dev_size
ce559078 Create.c: close mdfd and generate uevent
c3129b39 Detail: fix segfault during IMSM raid creation
97b51a2c Super1: allow RAID0 layout setting to be removed.
7f3b2d1d Check if other Monitor instance running before fork.
cab9c67d mdmonitor: set small delay once
007087d0 Monitor: stop notifing about containers.
e2308733 Monitor: refresh mdstat fd after select
2ce09172 Don't create bitmap for raid5 with journal disk
64bf4dff Detail: show correct raid level when the array is inactive
5f418455 manual: update --examine-badblocks
5e592e1e mdadm/md.4: update path to in-kernel-tree documentation
138a9e9b Specify nodes number when updating cluster nodes
77b72fa8 mdadm/Grow: prevent md's fd from being occupied during delayed time
bcf40dbb Update link to Intel page for IMSM
8e41153c Use more secure HTTPS URLs
2cf04330 Detect too-small device: error rather than underflow/crash
7758ada9 Block overwriting existing links while manual assembly
d92cee7b restripe: fix ignoring return value of ‘read’ and lseek
7d90f760 Include count for \0 character when using strncpy to implement strdup.
f4c8a605 uuid.c: split uuid stuffs from util.c
03ab9763 Makefile: add EXTRAVERSION support
3b7aae92 mdcheck: Log when done
7b99edab Assemble.c: respect force flag.
ec7d7cee clean up meaning of small typo
5cfb79de Assemble: print error message if mdadm fails assembling with --uuid option
12724c01 Manage, imsm: Write metadata before add
1c294b5d Detail: adding sync status for cluster device
185ec439 Monitor: improve check_one_sharer() for checking duplicated process
e1b92ee0 udev: Ignore change event for imsm
ba1b3bc8 imsm: show Subarray and Volume ID in --examine output
e48aed3c imsm: support the Array Creation Time field in metadata
9e449405 Detail: show correct bitmap info for cluster raid device
06a6101c imsm: Correct minimal device size.
45c43276 imsm: Remove --dump/--restore implementation
3364781b imsm: pass subarray id to kill_subarray function
fd38b8ea Remove the legacy whitespace
2551061c mdadm.8: add note information for raid0 growing operation
1e93d0d1 imsm: fill working_disks according to metadata.
42e641ab Add support for Tebibytes
4431efeb imsm: Update grow manual.
e1512e7b mdcheck service can't start succesfully because of syntax error
1a874930 Change warning message
aced6fc9 Respect $(CROSS_COMPILE) when $(CC) is the default
027c099f Assemble: add support for RAID0 layouts.
329dfc28 Create: add support for RAID0 layouts.
6da53c0e imsm: Change the way of printing nvme drives in detail-platform.
b771faef imsm: return correct uuid for volume in detail
4b31846f Remove unused code
9cf361f8 Fix up a few formatting issues
02af3793 Remove last traces of HOT_ADD_DISK
1cc3965d Manage: Remove the legacy code for md driver prior to 0.90.03
761e3bd9 super-intel: don't mark structs 'packed' unnecessarily
85b83a79 SUSE-mdadm_env.sh: handle MDADM_CHECK_DURATION
4ca799c5 mdcheck: use ${} to pass variable to mdcheck
6636788a mdcheck: when mdcheck_start is enabled, enable mdcheck_continue too.
1a1ced1e imsm: allow to specify second volume size
b6180160 imsm: save current_vol number
7bd59e79 udev: allow for udev attribute reading bug.
61109314 Don't need to check recovery after re-add when no I/O writes to raid
8063fd0f Init devlist as an array
e53cb968 mdadm/md.4: add the descriptions for bitmap sysfs nodes
2c2d9c48 mdadm: force a uuid swap on big endian
43ebc910 mdadm: Introduce new array state 'broken' for raid0/linear
fd5b09c9 mdadm: check value returned by snprintf against errors
91c97c54 imsm: close removed drive fd.
1a52f1fc udev: add --no-devices option for calling 'mdadm --detail'
d11abe4b mdadm: add --no-devices to avoid component devices detail information
452dc4d1 mdadm.h: include sysmacros.h unconditionally
b0681598 mdadm: load default sysfs attributes after assemblation
486720e0 super-intel: Use put_unaligned in split_ull
7039d1f8 mdadm.h: Introduced unaligned {get,put}_unaligned{16,32}()
a4f7290c super-intel: Fix issue with abs() being irrelevant
4ec389e3 Enable probe_roms to scan more than 6 roms.
ae7d61e3 mdmon: fix wrong array state when disk fails during mdmon startup
3c9b46cf udev: Add udev rules to create by-partuuid for md device
22dc741f Create: Block rounding size to max
05501181 imsm: fix spare activation for old matrix arrays
227aeaa8 add missing units to --examine
2b57e4fe Assemble: Fix starting array with initial reshape checkpoint
d2e11da4 mdmon: wait for previous mdmon to exit during takeover
69d08478 mdmon: don't attempt to manage new arrays when terminating
76b906d2 mdadm/tests: add one test case for failfast of raid1
cab114c5 Fix reshape for decreasing data offset
e3615ecb Detail.c: do not skip first character when calling xstrdup in Detail()
ebf3be99 Fix spelling typos.
9f421827 imsm: fix reshape for >2TB drives
a4e96fd8 imsm: finish recovery when drive with rebuild fails
757e5543 policy.c: Fix for compiler error
467e6a1b policy.c: prevent NULL pointer referencing
76d505de Grow: report correct new chunk size.
085df422 Grow: avoid overflow in compute_backup_blocks()
563ac108 Assemble: mask FAILFAST and WRITEMOSTLY flags when finding the most recent device
d7a1fda2 imsm: update metadata correctly while raid10 double degradation
7cd7e91a Monitor: add system timer to run --oneshot periodically
4199d3c6 mdcheck: add systemd unit files to run mdcheck.
cd72f9d1 policy: support devices with multiple paths.
6b611284 Document PART-POLICY lines
0833f9c3 Assemble: keep MD_DISK_FAILFAST and MD_DISK_WRITEMOSTLY flag
Signed-off-by: Nick Hainke <vincent@systemli.org>
33f1e0b treewide: move json-c compat shims into internal header file
e0e9431 vm: move unhandled exception reporting out of `uc_vm_execute_chunk()`
2b59140 vm: fix callframe double free on unhanded exceptions
7d7e950 main: abort when failing to load a preload library
1032a67 lib: let `json()` accept input objects implementing `read()` method
5ee68d5 fs: implement `fs.readfile()` and `fs.writefile()`
df6b861 ci: debian: change path before attempting to invoke Git operations
dfaf05a ci: debian: automatically update changelog from Git tag
34f3c45 ci: fix YAML syntax of Debian workflow
e956bcf fs: fix off-by-one in fs.dirname() function
6fc4b6c .gitignore: fix overmatching patterns, blacklist cram .venv
7c2e082 build: remove legacy json-c check
77942af build: add polyfills for older libjson-c versions
0b4aaa3 CI: build Debian package
f404285 debian: Add package definition
a37f654 types: fix escape sequence encoding of high byte values in JSON strings
aae5312 Update README.md
8134e25 build: fix symlink install target
87c7296 treewide: replace some leftover "utpl" occurrences, update .gitignore
7d27ad5 build: only stage ucc symlink if compile support is enabled
171402f lib: add date and time related functions
8b5dc60 lib: provide API function to obtain stdlib function implementations
eb0d2f1 main: turn ucode into multicall executable
28ee7e1 uloop: add support for tasks
753dea9 CI: build on macOS
668c5c0 lib: add argument position support (`%m$`) to `sprintf()` and `printf()`
ab46fdf treewide: remove legacy json-c include directives
b8f49b1 tests: 21_regex_literals: generalize syntax error test case
fd2e5e7 tests: 16_sort: fix logic flaw exposed on OS X
2c71bf2 tests: run_tests.sh: pass dummy value to `-T` flag
55c4a90 lib: disallow zero padding for %s formats
0d05cb5 tests: run_tests.sh: use greadlink if available
271e520 resolv: make OS X compatible
d13c320 fs: avoid Linux specific sys/sysmacros.h include on OS X
33397a3 uloop: use execvp() on OS X
bafdc8f lib: add naive sigtimedwait() stub for OS X
ada1585 build: consolidate CMakeLists.txt and cover OS X deviations
befbb69 include: add OS X compatible endian.h header
49838a8 include: rename include guards to avoid clashes with system headers
91f65de nl80211: add missing attributes and correct some attribute flags
b4a1fd5 lib: adjust require(), render() and include() raw mode semantics
4618807 main: rework CLI frontend
73dcd78 lib: fix potential integer underflow on empty render output
c402551 vm: fix crash on object literals with non-string computed properties
efe8a02 syntax: support add new operators
078d686 ubus: add event support
6c66c83 ubus: refactor error and argument handling
1cb04f9 ubus: add object publishing, notify and subscribe support
0e85974 uloop: clear errno before integer conversion attempts
05bd7ed types: treat resource type prototypes as GC roots
a2a26ca lib: introduce uloop binding
6b6d01f vm: release this context on exception in managed method call
1af23a9 tests: fix proto() testcase
4ce69a8 fs: implement access(), mkstemp(), file.flush() and proc.flush()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The first argument for snprintf is the buffer and the 2. one is the
size. Fix the order. This broke the lock application.
Fixes: 34567750db ("busybox: fix busybox lock applet pidstr buffer overflow")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kernel setting `/proc/sys/kernel/pid_max` can be set up to 4194304 (7
digits) which will cause buffer overflow in busbox lock patch, this
often happens when running in a rootfs container environment.
This commit enlarges `pidstr` to 12 bytes to ensure a sufficient buffer
for pid number and an additional char '\n'.
Signed-off-by: Qichao Zhang <njuzhangqichao@gmail.com>
a29bad9 compiler: fix patchlist corruption on switch statement syntax errors
86f0662 lib: change `ord()` to always return single byte value
116a8ce vallist: fix storing/retrieving short strings with 8bit byte value
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
11adf0c source: convert source objects into proper uc_value_t type
3a49192 treewide: rework function memory model
7edad5c tests: add functional tests for builtin functions
d5003fd lib: fix leaking tokener in uc_json() on parse exception
5d0ecd9 lib: fix infinite loop on empty regexp matches in uc_replace()
3ad57f1 lib: fix infinite loop on empty regexp matches in uc_match()
32d596d lib: fix infinite loop on empty regexp matches in uc_split()
3e3f38d vm: ensure consistent trace output between gcc and clang compiled ucode
3600ded vm: fix leaking function value on call exception
3059295 vm: NULL-initialize pointer to make cppcheck happy
98e59bf source: zero-initialize conversion union to make cppcheck happy
7a65c14 run_tests.sh: change workdir to testcase directory during execution
afec8d7 run_tests.sh: support placing supplemental testcase files
3ada6e0 run_tests.sh: always treat outputs as text data
2cb627f program: rename bytecode load/write functions, track path of executed file
1094ffa lib: fix memory leak in uc_require_ucode()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add a package for util-linux' ipcs command, to show information about
System V inter-process communication facilities.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This release fixes two security mount(8) and umount(8) issues:
CVE-2021-3996
Improper UID check in libmount allows an unprivileged user to unmount FUSE
filesystems of users with similar UID.
CVE-2021-3995
This issue is related to parsing the /proc/self/mountinfo file allows an
unprivileged user to unmount other user's filesystems that are either
world-writable themselves or mounted in a world-writable directory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The man page of the raw tool does not build because the disk-utils/raw.8
file is missing. It looks like it should be in the tar.xz file we
download, but it is missing.
We do not package the raw tool, so this is not a problem.
This fixes the following build error:
No rule to make target 'disk-utils/raw.8', needed by 'all-am'. Stop.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ucode VM always passes 64bit integer values to sprintf implementation
while the `%d` format expects 32bit integers on 32bit platforms, leading
to incorrect formatting results.
Temporarily solve the issue by casting the numeric argument to int until
a more thorough fix arrives with the next update.
Fixes: FS#4234
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Changes from 2.1.3 to 2.1.4:
Features:
- ubiscan debugging and statistics utility
Fixes:
- Some mtd-tests erroneously using sub-pages instead of the full page size
- Buffer overrun in fectest
- Missing jffs2 kernel header in the last release, leading to build
failures on some systems.
Changes from 2.1.2 to 2.1.3:
Features:
flashcp: Add new function that copy only different blocks
flash_erase: Add flash erase chip
Add flash_otp_erase
Add an ubifs mount helper
Add nandflipbits tool
Fixes:
mkfs.ubifs: Fix runtime assertions when running without crypto
mtd-utils: Use AC_SYS_LARGEFILE
Fix test binary installation
libmtd: avoid divide by zero
ubihealthd: fix UBIFS build dependency
mkfs.ubifs: remove OPENSSL_no_config()
misc-utils: Add fectest to build system
mkfs.ubifs: Fix build with SELinux
Fix typos found by Debian's lintian tool
Fix jffs2 build if zlib or lzo headers are not in default paths
Signed-off-by: Nick Hainke <vincent@systemli.org>
Update busybox to 1.35.0
* refresh patches
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in : change at "Options common to all shells" the symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
CHECK_RUN_DIR=0 must be a part of MAKE_FLAGS, not MAKE_VARS, otherwise
it is not possible to compile mdadm on host without /run dir.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
Compiling without fPIC causes linking issues for packages using liblua.
Add $(HOST_FPIC) to host builds for both lua and lua5.3.
Suggested-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Chromium based web-browsers (version >58) checks x509v3 extended attributes.
If this check fails then chromium does not allow to click "Proceed to ...
(unsafe)" link. This patch add three x509v3 extended attributes to self-signed
certificate:
1. SAN (Subject Alternative Name) (DNS Name) = CN (common name)
2. Key Usage = Digital Signature, Non Repudiation, Key Encipherment
3. Extended Key Usage = TLS Web Server Authentication
SAN will be added only if CONFIG_WOLFSSL_ALT_NAMES=y
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
fdt* utils are needed by targets that use U-Boot FIT images for
sysupgrade. It includes all recent BCM4908 SoC routers as Broadcom
switched from CFE to U-Boot.
fdtget is required for extracting images (bootfs & rootfs) from
Broadcom's ITB. Extracted images can be then flashed to UBI volumes.
sysupgrade is core functionality so it needs dtc as part of base code
base.
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Set the different libf2fs packages's VARIANT, so that the right settings
will be used by each different variant, if they are both being built.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
Correct some typos
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsepol/secilc/docs: Update the CIL documentation
secilc: fix memory leaks in secilc2conf
secilc: fix memory leaks in secilc
libsepol/cil: Add support for using qualified names to secil2conf
libsepol/cil: Add support for using qualified names to secil2tree
secilc: Add support for using qualified names to secilc
secilc/test: Add test for anonymous args
secilc/docs: Relocate and reword macro call name resolution order
secilc/docs: Document the order that inherited rules are resolved in
secilc: Create the new program called secil2tree to write out CIL AST
secilc/docs: Update the CIL documentation for various blocks
secilc.c: Don't fail if input file is empty
cil_conditional_statements.md: fix expr definition
secilc/docs: Lists are now allowed in constraint expressions
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[re-apply now that libsepol is up-to-date as well]
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
This reverts commit 2da891e735.
secilc 3.3 requires libsepol to be version 3.3 as well and doesn't
build otherwise. Revert for now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
Correct some typos
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsepol/secilc/docs: Update the CIL documentation
secilc: fix memory leaks in secilc2conf
secilc: fix memory leaks in secilc
libsepol/cil: Add support for using qualified names to secil2conf
libsepol/cil: Add support for using qualified names to secil2tree
secilc: Add support for using qualified names to secilc
secilc/test: Add test for anonymous args
secilc/docs: Relocate and reword macro call name resolution order
secilc/docs: Document the order that inherited rules are resolved in
secilc: Create the new program called secil2tree to write out CIL AST
secilc/docs: Update the CIL documentation for various blocks
secilc.c: Don't fail if input file is empty
cil_conditional_statements.md: fix expr definition
secilc/docs: Lists are now allowed in constraint expressions
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
libselinux/semodule: Improve extracting message
Correct some typos
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
policycoreutils: free memory of allocated context in newrole
policycoreutils: free memory of allocated context in run_init
policycoreutils: free memory on lstat failure in sestatus
policycoreutils: silence -Wextra-semi-stmt warning
fixfiles: do not exclude /dev and /run in -C mode
policycoreutils/setfiles: do not create useless setfiles.8.man file
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
checkpolicy: Fix potential undefined shifts
Update VERSIONs to 3.3-rc3 for release.
checkpolicy: delay down-cast to avoid align warning
checkpolicy: drop incorrect cast
checkpolicy: update documentation
checkpolicy: print reason of fopen failure
checkpolicy: policy_define: cleanup declarations
Update VERSIONs to 3.3-rc2 for release.
checkpolicy: free extended permission memory
checkpolicy: print warning on source line overflow
checkpolicy: error out on parsing too big integers
checkpolicy: avoid implicit conversion
checkpolicy: resolve dismod memory leaks
checkpolicy: add missing function declarations
checkpolicy: mark file local functions in policy_define static
checkpolicy: mark read-only parameters in module compiler const
checkpolicy: misc checkpolicy tweaks
checkpolicy: misc checkmodule tweaks
checkpolicy: enclose macro argument in parentheses
Update VERSIONs and Python bindings version to 3.3-rc1 for release
checkpolicy: mark read-only parameters in policy define const
checkpolicy/test: mark file local functions static
checkpolicy: parse_util drop unused declaration
checkpolicy: drop redundant cast to the same type
checkpolicy: avoid potential use of uninitialized variable
checkpolicy: check before potential NULL dereference
checkpolicy: remove dead assignments
checkpolicy: follow declaration-after-statement
checkpolicy: use correct format specifier for unsigned
checkpolicy: drop dead condition
checkpolicy: simplify assignment
checkpolicy: drop -pipe compile option
checkpolicy: pass CFLAGS at link stage
checkpolicy: silence -Wextra-semi-stmt warning
checkpolicy: Do not automatically upgrade when using "-b" flag
libsepol/checkpolicy: Set user roles using role value instead of dominance
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
