Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.
The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.
Test passed on my tplink tl-wdr4310.
Signed-off-by: Edward Chow <equu@openmail.cc>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.
This should make simplify the conversion of target to nvmem implementation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
AR8327 datasheet[1] calls the register at address 0x0010
"Power-on Strapping Register". As it has nothing to do with "strip",
let's rename it to "POWER_ON_STRAP" to make it easier to grasp.
[1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
The full address assignment is as follows:
LAN label
WAN label + 1
5G label
2G label - 1
This patch changes all devices using TL-WDR4300 board:
TL-WDR3600 v1 (checked on device)
TL-WDR4300 v1 (checked on device)
TL-WDR4300 v1 (IL)
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase/extend commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This partially reverts commit 32144ba275.
This commit replaced gpio-exports in favor of gpio-hogs for enabling USB
power at boot, but this rids the user of control of the USB port power
present on this device for a long time. It was agreed on a mailing list
[1] that this is not the way to go, and this patch breaks a very common
use-case of WWAN modem reset by power cycle, used on a lot USB equipped
routers, hence revert this change until a better solution can be found.
[1] http://lists.infradead.org/pipermail/openwrt-devel/2019-November/020151.html
Tested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds the label MAC address for several devices in
ath79.
Some devices require setting the MAC address in 02_network:
For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices
For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware:
SoC: AR9344
CPU: 560 MHz
Flash: 8 MiB
RAM: 128 MiB
WiFi: Atheros AR9340 2.4GHz 802.11bgn
Atheros AR9300 5GHz 802.11an
Ethernet: AR934X built-in switch, WAN on separate physical interface
USB: 1x 2.0
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wdr3500v1_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[removed stray newline]
Signed-off-by: David Bauer <mail@david-bauer.net>
This replaces gpio-export by gpio-hogs and switches buttons
to interrupt-driven gpio-keys.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
>From the Documentation/devicetree/bindings/leds/common.txt:
- default-state : The initial state of the LED. Valid values are "on", "off",
and "keep". If the LED is already on or off and the default-state property is
set the to same value, then no glitch should be produced where the LED
momentarily turns off (or on). The "keep" setting will keep the LED at
whatever its current state is, without producing a glitch. The default is
off if this property is not present.
So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Parsing "firmware" partition (to create kernel + rootfs) was implemented
using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With
recent upstream mtd changes we can do it in a more clean way for DTS
targets. It just requires adding a proper "compatible" string to the
"firmware" partition node.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which
supports different leds for the different boot states.
The existing led sequences should be the same as before.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix all issues found by the devicetree compiler like wrong address/size
cells as well as wrong/missing/superfluous unit addresses.
Signed-off-by: Mathias Kresin <dev@kresin.me>
