After the ath10k_patch_mac lines have been removed, a lot of blocks
can be consolidated.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switched to normalizing the partition names to lower case.
While both 5.4 and 5.10 were supported in the target, we carried a workaround
to support both of them. Since the target has dropped 5.4 recently, those
can be removed now.
Ref:
2db9dded0a ("ipq806x: nbg6817: case-insensitive qcom-smem partitions")
435dc2e77e ("ipq806x: ecw5410: case-insensitive qcom-smem partitions")
f70e11cd97 ("ipq806x: g10: case-insensitive qcom-smem partitions")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use nvmem framework for supported mac-address stored
in nvmem cells and drop mac patch function for hotplug
script for supported devices.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase, move to correct node for d7800, include xr500]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specs (same as in v1):
- MT7628AN (575 MHz)
- 64MB RAM
- 8MB of flash (SPI NOR)
- 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan)
- 1x 2.4GHz wifi (MT7628AN)
- 1x 5Ghz wifi (MT7612E)
- 4x LEDs (5 GPIO-controlled)
- 1x reset button
- 1x WPS button
The only and important difference between v1 & v3 is in flash memory
layout, so pls don't interchange these 2 builds!
Installation through web-ui (on OEM factory firmware):
1. Visit http://tplinkrepeater.net or the configured IP address of
your RE305 v3 (default 192.168.0.254).
2. Log in with the password you've set during initial setup of the
RE305 (there is no default password).
3. Go to Settings -> System Tools -> Firmware upgrade
4. Click Browse and select the OpenWRT image with factory.bin suffix
(not sysupgrade.bin)
5. A window with a progress bar will appear. Wait until it completes.
6. The RE305 will reboot into OpenWRT and serve DHCP requests on the
ethernet port.
7. Connect an RJ45 cable from the RE305 to your computer and access
LuCI at http://192.168.1.1/ to configure (or use ssh).
Disassembly:
Just unscrew 4 screws in the corners & take off the back cover.
Serial is exposed to the right side of the main board (in the middle)
and marked with TX/RX/3V3/GND, but the holes are filled with solder.
Installation through serial:
1. connect trough serial (1n8, baudrate=57600)
2. setup the TFTP server and connect it via ethernet
(ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc)
3. boot from a initramfs image first (choose 1 in the bootloader
options)
4. test it a bit with that, then proceed to run sysupgrade build
MAC addresses as verified by OEM firmware:
use OpenWrt address reference
LAN eth0 *:d2 label
2g wlan0 *:d1 label - 1
5g wlan1 *:d0 label - 2
The label MAC address can be found in config 0x2008.
Signed-off-by: Michal Kozuch <servitkar@gmail.com>
[redistribute WLAN node properties between DTS/DTSI, remove
compatible on DTSI, fix indent/wrapping, split out firmware-utils
change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
7073760 ramips: add support for TP-Link RE305 v3
86739f2 Add more missing include for byte swap operations
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ELECOM WRC-X3200GST3 uses the same header/footer as WRC-GS/GST devices
in ramips/mt7621 subtarget, so move "Build/elecom-wrc-gs-factory" to
image-commands.mk to use from mediatek/mt7622 subtarget.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Specification:
CPU: Allwinner H5, Quad-core Cortex-A53
DDR3 RAM: 512MB
Network: 10/100/1000M Ethernet x 2
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input
Debug Serial Port: 3Pin pin-header
LED: WAN, LAN, SYS
KEY: Reset
Power Supply: DC 5V/2A
Installation:
Write the image to SD Card with dd.
Note:
1. OpenWrt currently does not support LED_FUNCTION, change back to the
previous practice (Consistent with NanoPi R1).
2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71
("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to
change the phy-mode from rgmii to rgmii-id.
So set phy-mode for 5.4 and 5.10 respectively.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport upstream fix for module load regression caused by IRAM recovery.
Without this patch devices using mainline ath10k driver could lost wireless
function because ath10k module failed to load.
Signed-off-by: Zhijun You <hujy652@gmail.com>
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")
| 2. updating ath10k-firmware-qca4019 will also replace
| the board-2.bin. For this cases the user needs to
| manually reinstall the wifi-board package once the
| ath10k-firmware-qca4019 is updated.
This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
OpenWrt maintains two special out-of-tree DT properties:
"qca,disable-5ghz" and "qca,disable-2ghz". These are implemented
in a mac80211 ath9k patch "550-ath9k-disable-bands-via-dt.patch".
With the things being what they are, now might be a good
point to switch the devices to the generic and upstream
"ieee80211-freq-limit" property. This property is much
broader and works differently. Instead of disabling the
drivers logic which would add the affected band and
channels. It now disables all channels which are not
within the specified frequency range.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # HH5A
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* SSH agent forwarding might cause security issues, locally and on the jump
machine (https://defn.io/2019/04/12/ssh-forwarding/). So allow to
completely disabling it.
* separate options for client and server
* keep it enabled by default
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Commit 03e1d93e07 ("realtek: add driver support for routing
offload") added routing offload for IPv4, but broke IPv6 routing
completely. The routing table is empty and cannot be updated:
root@gs1900-10hp:~# ip -6 route
root@gs1900-10hp:~# ip -6 route add unreachable default
RTNETLINK answers: Invalid argument
As a side effect, this breaks opkg on IPv4 only systems too,
since uclient-fetch fails when there are no IPv6 routes:
root@gs1900-10hp:~# uclient-fetch http://192.168.99.1
Downloading 'http://192.168.99.1'
Failed to send request: Operation not permitted
Fix by returning NOTIFY_DONE when offloading is unsupported, falling
back to default behaviour.
Fixes: 03e1d93e07 ("realtek: add driver support for routing offload")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The current rule produces empty trailers, causing the OEM firmware
update application to reject our images.
The double expansion of a makefile variable does not work inside
shell code. The second round is interpreted as a shell expansion,
attempting to run the command ZYXEL_VERS instead of expanding the
$(ZYXEL_VERS) makefile variable.
Fix by removing one level of variable indirection.
Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")
Tested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
During review of the MR32, Florian Fainelli pointed out that the
SoC has a real I2C-controller. Furthermore, the connected pins
(SDA and SCL) would line up perfectly for use. This patch swaps
out the the bitbanged i2c-gpio with the real deal.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Deselect CONFIG_VIDEO_SUN6I_CSI Kconfig symbol for now. If anyone wants
to use CSI (camera interface) they should package the kernel module.
After this change, sunxi targets build again.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This switches pinctrl driver to use the old & good DT binding. There is
no more need to adjust upstream DTS file.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Simply disable this for now, if anyone wants to use CSI feel free to
package it as a kernel module package.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 2da891e735.
secilc 3.3 requires libsepol to be version 3.3 as well and doesn't
build otherwise. Revert for now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit de8a800ca9.
Host build uses host includes instead of staging/hostpkg.
This breaks the build in case of selinux host libs being older than
version 3.3. Revert for now until better fix is found.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
wifi: writes to terminal
hotplugcall and sqm read class sysfile symlinks
unbound and sqm related loose ends
support/example: policycoreutils host-compile is required
TODO: this was wrong and it is actually needed
linguist detectable does not work this way
linguist-detectable
updates README
adds workflows
adds a note about persistent /var option
project moved to https://github.com/DefenSec/selinux-policy
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
Correct some typos
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsepol/secilc/docs: Update the CIL documentation
secilc: fix memory leaks in secilc2conf
secilc: fix memory leaks in secilc
libsepol/cil: Add support for using qualified names to secil2conf
libsepol/cil: Add support for using qualified names to secil2tree
secilc: Add support for using qualified names to secilc
secilc/test: Add test for anonymous args
secilc/docs: Relocate and reword macro call name resolution order
secilc/docs: Document the order that inherited rules are resolved in
secilc: Create the new program called secil2tree to write out CIL AST
secilc/docs: Update the CIL documentation for various blocks
secilc.c: Don't fail if input file is empty
cil_conditional_statements.md: fix expr definition
secilc/docs: Lists are now allowed in constraint expressions
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
libselinux/semodule: Improve extracting message
Correct some typos
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
policycoreutils: free memory of allocated context in newrole
policycoreutils: free memory of allocated context in run_init
policycoreutils: free memory on lstat failure in sestatus
policycoreutils: silence -Wextra-semi-stmt warning
fixfiles: do not exclude /dev and /run in -C mode
policycoreutils/setfiles: do not create useless setfiles.8.man file
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
checkpolicy: Fix potential undefined shifts
Update VERSIONs to 3.3-rc3 for release.
checkpolicy: delay down-cast to avoid align warning
checkpolicy: drop incorrect cast
checkpolicy: update documentation
checkpolicy: print reason of fopen failure
checkpolicy: policy_define: cleanup declarations
Update VERSIONs to 3.3-rc2 for release.
checkpolicy: free extended permission memory
checkpolicy: print warning on source line overflow
checkpolicy: error out on parsing too big integers
checkpolicy: avoid implicit conversion
checkpolicy: resolve dismod memory leaks
checkpolicy: add missing function declarations
checkpolicy: mark file local functions in policy_define static
checkpolicy: mark read-only parameters in module compiler const
checkpolicy: misc checkpolicy tweaks
checkpolicy: misc checkmodule tweaks
checkpolicy: enclose macro argument in parentheses
Update VERSIONs and Python bindings version to 3.3-rc1 for release
checkpolicy: mark read-only parameters in policy define const
checkpolicy/test: mark file local functions static
checkpolicy: parse_util drop unused declaration
checkpolicy: drop redundant cast to the same type
checkpolicy: avoid potential use of uninitialized variable
checkpolicy: check before potential NULL dereference
checkpolicy: remove dead assignments
checkpolicy: follow declaration-after-statement
checkpolicy: use correct format specifier for unsigned
checkpolicy: drop dead condition
checkpolicy: simplify assignment
checkpolicy: drop -pipe compile option
checkpolicy: pass CFLAGS at link stage
checkpolicy: silence -Wextra-semi-stmt warning
checkpolicy: Do not automatically upgrade when using "-b" flag
libsepol/checkpolicy: Set user roles using role value instead of dominance
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsemanage: Fix USE_AFTER_FREE (CWE-672) in semanage_direct_write_langext()
libsemanage: silence -Wextra-semi-stmt warning
libsemanage: fix use-after-free in parse_module_store()
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
libselinux: Fix potential undefined shifts
Update VERSIONs to 3.3-rc3 for release.
Update VERSIONs to 3.3-rc2 for release.
libselinux/utils: drop requirement to combine compiling and linking
Update VERSIONs and Python bindings version to 3.3-rc1 for release
Improve error message for label file validation
libselinux: replace strerror by %m
libselinux: silence -Wextra-semi-stmt warning
libselinux/utils/getseuser.c: fix build with gcc 4.8
selinux.8: document how mount flag nosuid affects SELinux
libselinux: fix typo
libselinux: improve getcon(3) man page
libselinux: selinux_status_open: return 1 in fallback mode
libselinux: do not use status page fallback mode internally
libselinux: make selinux_status_open(3) reentrant
libselinux: avc_destroy(3) closes status page
libselinux: label_file.c: fix indent
libselinux: regex: unify parameter names
libselinux: sidtab_sid_stats(): unify parameter name
libselinux: drop redundant casts to the same type
libselinux: label_db::db_init(): open file with CLOEXEC mode
libselinux: matchpathcon: free memory on realloc failure
libselinux: label_file::init(): do not pass NULL to strdup
libselinux: init_selinux_config(): free resources on error
libselinux: matchmediacon(): close file on error
libselinux: store_stem(): do not free possible non-heap object
libselinux: getdefaultcon: free memory on multiple same arguments
libselinux: setexecfilecon(): drop dead assignment
libselinux: label_media::init(): drop dead assignment
libselinux: label_x::init(): drop dead assignment
libselinux: context_new(): drop dead assignment
libselinux: exclude_non_seclabel_mounts(): drop unused variable
libselinux: getconlist: free memory on multiple level arguments
libselinux: selabel_get_digests_all_partial_matches: free memory after FTS_D block
libselinux: selinux_restorecon: mark local variable static
libselinux: avcstat: use standard length modifier for unsigned long long
libselinux: sefcontext_compile: mark local variable static
libselinux: Sha1Finalise(): do not discard const qualifier
libselinux: label_common(): do not discard const qualifier
libselinux: selinux_file_context_cmp(): do not discard const qualifier
libselinux: sidtab_hash(): do not discard const qualifier
libselinux: silence -Wstringop-overflow warning from gcc 10.3.1
libselinux: selinux_check_passwd_access_internal(): respect deny_unknown
libselinux: do not duplicate make target when going into subdirectory
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
libsepol/cil: Fix potential undefined shifts
libsepol: Fix potential undefined shifts
Update VERSIONs to 3.3-rc3 for release.
libsepol/cil: Do not skip macros when resolving until later passes
libsepol/cil: Limit the amount of reporting for bounds failures
libsepol/cil: silence clang void-pointer-to-enum-cast warning
libsepol: resolve GCC warning about null-dereference
libsepol: use correct cast
libsepol: ebitmap: mark nodes of const ebitmaps const
Update VERSIONs to 3.3-rc2 for release.
libsepol/cil: Handle operations in a class mapping when verifying
libsepol/cil: Do not use original type and typeattribute datums
libsepol: free memory after policy validation
libsepol: avoid implicit conversions
libsepol: fix typo
libsepol/cil: Free duplicate datums in original calling function
libsepol/cil: Fix detected RESOURCE_LEAK (CWE-772)
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsepol/cil: Limit the number of active line marks
libsepol/cil: Add function to get number of items in a stack
libsepol: Fix detected RESOURCE_LEAKs
libsepol/cil: Fix syntax checking in __cil_verify_syntax()
libsepol/cil: Use size_t for len in __cil_verify_syntax()
libsepol/cil: Remove redundant syntax checking
libsepol/cil: Improve in-statement to allow use after inheritance
libsepol/cil: Simplify cil_tree_children_destroy()
libsepol/cil: Refactor the function __cil_build_ast_node_helper()
libsepol/cil: Don't destroy optionals whose parent will be destroyed
libsepol/cil: Properly check for parameter when inserting name
libsepol/cil: Reset expandtypeattribute rules when resetting AST
libsepol/cil: Properly check parse tree when printing error messages
libsepol/cil: Allow some duplicate macro and block declarations
libsepol/cil: When writing AST use line marks for src_info nodes
libsepol/cil: Report correct high-level language line numbers
libsepol/cil: Add line mark kind and line number to src info
libsepol/cil: Create common string-to-unsigned-integer functions
libsepol/cil: Push line mark state first when processing a line mark
libsepol/cil: Check for valid line mark type immediately
libsepol/cil: Check the token type after getting the next token
libsepol/cil: Check syntax of src_info statement
libsepol/cil: move the fuzz target and build script to the selinux repository
libsepol: replace strerror by %m
libsepol/cil: remove obsolete comment
libsepol/cil: do not allow \0 in quoted strings
libsepol/cil: Fix handling category sets in an expression
libsepol: assure string NUL-termination of ibdev_name
libsepol: avoid implicit conversions
libsepol: ignore UBSAN false-positives
libsepol: avoid unsigned integer overflow
libsepol/cil: Improve checking for bad inheritance patterns
libsepol: silence -Wextra-semi-stmt warning
libsepol/cil: do not override previous results of __cil_verify_classperms
libsepol/cil: Provide option to allow qualified names in declarations
libsepol/cil: make array cil_sym_sizes const
libsepol/cil: Only reset AST if optional has a declaration
libsepol/cil: Add function to determine if a subtree has a declaration
libsepol/cil: Improve degenerate inheritance check
libsepol/cil: Reduce the initial symtab sizes for blocks
libsepol/cil: Check for empty list when marking neverallow attributes
libsepol/cil: Fix syntax checking of defaultrange rule
libsepol/cil: Properly check for loops in sets
libsepol/cil: Allow duplicate optional blocks in most cases
libsepol: declare read-only arrays const
libsepol: declare file local variable static
libsepol: drop unnecessary casts
libsepol: drop repeated semicolons
libsepol/cil: avoid using maybe uninitialized variables
libsepol/cil: drop unnecessary casts
libsepol/cil: drop dead store
libsepol/cil: drop extra semicolon
libsepol/cil: silence cast warning
libsepol: remove dead stores
libsepol: do not allocate memory of size 0
libsepol: mark read-only parameters of type_set_ interfaces const
libsepol: mark read-only parameters of ebitmap interfaces const
libsepol: remove dead stores
libsepol/cil: follow declaration-after-statement
libsepol: follow declaration-after-statement
libsepol: avoid unsigned integer overflow
libsepol: remove unused functions
libsepol: resolve missing prototypes
libsepol: fix typos
libsepol: Quote paths when generating policy.conf from binary policy
libsepol/cil: Account for anonymous category sets in an expression
libsepol/cil: Fix anonymous IP address call arguments
libsepol: quote paths in CIL conversion
libsepol/cil: Resolve anonymous levels only once
libsepol/cil: Pointers to datums should be set to NULL when resetting
libsepol/cil: Resolve anonymous class permission sets only once
libsepol/cil: Limit the number of open parenthesis allowed
libsepol/cil: Destroy the permission nodes when exiting with an error
libsepol/cil: Handle disabled optional blocks in earlier passes
libsepol/cil: Do not resolve arguments to declarations in the call
libsepo/cil: Refactor macro call resolution
libsepol/cil: Do not add NULL node when inserting key into symtab
libsepol/cil: Make name resolution in macros work as documented
libsepol/cil: Fix name resolution involving inherited blocks
libsepol/cil: Check for self-referential loops in sets
libsepol/cil: Return an error if a call argument fails to resolve
libsepol/cil: Check datum in ordered list for expected flavor
libsepol/cil: Detect degenerate inheritance and exit with an error
libsepol/cil: Fix instances where an error returns SEPOL_OK
libsepol/cil: Properly reset an anonymous classperm set
libsepol: use checked arithmetic builtin to perform safe addition
libsepol/cil: Add functions to make use of cil_write_ast()
libsepol/cil: Create functions to write the CIL AST
libsepol/cil: Use CIL_ERR for error messages in cil_compile()
libsepol/cil: Make invalid statement error messages consistent
libsepol/cil: Do not allow tunable declarations in in-statements
libsepol/cil: Sync checks for invalid rules in macros
libsepol/cil: Check for statements not allowed in optional blocks
libsepol/cil: Sync checks for invalid rules in booleanifs
libsepol/cil: Reorder checks for invalid rules when resolving AST
libsepol/cil: Use AST to track blocks and optionals when resolving
libsepol/cil: Create new first child helper function for building AST
libsepol/cil: Cleanup build AST helper functions
libsepol/cil: Reorder checks for invalid rules when building AST
libsepol/cil: Move check for the shadowing of macro parameters
libsepol/cil: Create function cil_add_decl_to_symtab() and refactor
libsepol/cil: Refactor helper function for cil_gen_node()
libsepol/cil: Allow permission expressions when using map classes
libsepol/cil: Exit with an error if declaration name is a reserved word
libsepol/cil: More strict verification of constraint leaf expressions
libsepol/cil: Set class field to NULL when resetting struct cil_classperms
libsepol/cil: cil_reset_classperms_set() should not reset classpermission
libsepol/cil: Destroy classperm list when resetting map perms
libsepol/cil: Destroy classperms list when resetting classpermission
libsepol/cil: Fix out-of-bound read of file context pattern ending with "\"
libsepol/cil: Check for duplicate blocks, optionals, and macros
libsepol: Write "NO_IDENTIFIER" for empty CIL constraint expression
libsepol: Enclose identifier lists in CIL constraint expressions
libsepol/cil: Allow lists in constraint expressions
libsepol: Enclose identifier lists in constraint expressions
libsepol: Write "NO_IDENTIFIER" for empty constraint expression
libsepol: make num_* unsigned int in module_to_cil
libsepol/cil: do not leak avrulex_ioctl_table memory when an error occurs
libsepol/cil: fix NULL pointer dereference in __cil_insert_name
libsepol/cil: replace printf with proper cil_tree_log
libsepol/cil: remove stray printf
libsepol/cil: make cil_post_fc_fill_data static
libsepol: Check kernel to CIL and Conf functions for supported versions
libsepol: Remove unnecessary copying of declarations from link.c
libsepol: Properly handle types associated to role attributes
libsepol: Expand role attributes in constraint expressions
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
In case of the block device still being in use, re-reading the
partition table fails. In that case, abort sysupgrade to avoid
corrupting the just-written image because of wrong offsets caused
by failure to re-read the partition table.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some packages may require additional group membership for the system
user added by that package. Allow defining additional groups as third
member of the ':'-separated tuple, allowing to specify multiple
','-separated groups with optional GID.
Example:
USERID:=foouser=1000:foogroup=1000:addg1=1001,addg2=1002,addg3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The 'madvise', syscall is missing.
Found with 'utrace /usr/sbin/umdns' on an R7800 and RT3200.
Signed-off-by: Michael Peleshenko <mpeleshenko@gmail.com>
This adds support for the Netgear Nighthawk Pro Gaming XR500.
It is the successor to the Netgear Nighthawk R7800 and shares almost
identical hardware to that device.
The stock firmware is a heavily modified version of OpenWRT.
Specifications:
SoC: Qualcomm Atheros IPQ8065
RAM: 512 MB
Storage: 256 MiB NAND Flash
Wireless: 2x Qualcomm Atheros QCA9984
Ethernet: 2x 1000/100/10 dedicated interfaces
Switch: 5x 1000/100/10 external ports
USB: 2x 3.0 ports
More information:
Manufacturer page: https://www.netgear.com/gaming/xr500/
Almost identical to Netgear R7800
Differences (r7800 > xr500):
Flash: 128MiB > 256MiB
Removed esata
swapped leds:
usb1 (gpio 7 > 8)
usb2 (gpio 8 > 26)
guest/esata (gpio 26 > 7)
MAC addresses:
On the OEM firmware, the mac addresses are:
WAN: *:50 art 0x6
LAN: *:4f art 0x0 (label)
2G: *:4f art 0x0
5G: *:51 art 0xc
Installation:
Install via Web Interface (preferred):
Utilize openwrt-ipq806x-netgear_xr500-squashfs-factory.img
Install via TFTP recovery:
1.Turn off the power, push and hold the reset button (in a hole on
backside) with a pin
2.Turn on the power and wait till power led starts flashing white
(after it first flashes orange for a while)
3.Release the reset button and tftp the factory img in binary mode.
The power led will stop flashing if you succeeded in transferring
the image, and the router reboots rather quickly with the new
firmware.
4.Try to ping the router (ping 192.168.1.1). If does not respond,
then tftp will not work either.
Uploading the firmware image with a TFTP client
$ tftp 192.168.1.1
bin
put openwrt-ipq806x-netgear_xr500-squashfs-factory.img
Note:
The end of the last partition is at 0xee00000. This was chosen
by the initial author, but nobody was able to tell why this
particular arbitrary size was chosen. Since it's not leaving
too much empty space and it's the only issue left, let's just
keep it for now.
Based on work by Adam Hnat <adamhnat@gmail.com>
ref: https://github.com/openwrt/openwrt/pull/3215
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
[squash commits, move common LEDs to DTSI, remove SPDX on old
files, minor whitespace cleanup, commit message facelift,
add MAC address overview, add Notes, fix MAC addresses,
use generic name for partition nodes in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Allow RAM size to be passed thru U-Boot. There are 128MB and 64MB
versions of Minew G1-C. This is also in line with the behaviour of
most other RAMIPS boards.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Compile tested and run tested on Pine64+.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add support for SAM9X60-EK board.
Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
devices
Flashing:
- follow the procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D27 WLSOM1-EK board.
Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
(ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
connector
- Power managament: PMIC (MCP16502)
Flashing:
- follow procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D2 ICP board.
Hardware:
- SoC: SAMA5D27
- RAM: 512 MB DDR3L
- MMC: One stanard SD card interface
- USB: One USB host switch 4 ports with power switch,
One USB device type Micro-AB
- CAN: 2 interfaces
- Ethernet: One Gigabit Ethernet PHY through HSIC,
One ETH switchport,
One EtherCAT interface
- WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus
Bluetooth module (Wi-Fi/BT), suitable for
Microchip WILC3000-MR110CA or WILC3000-MR110UA
- Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: reset, wakeup, 2 user buttons
- Expansion: one PIOBU/PIO connector, 3 mikrobus sockets
- Power mangament: PMIC (MCP16502), one power consumption device
(PAC1934)
Not working in Linux:
- EtherCAT interface: there is no Linux support integrated
- PAC1934: driver available at [1] but not integrated in Linux
Flashing:
- follow the procedure at [2]
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip
[2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
