Mux the MT7530 switch's phy0/4 to the SoC's gmac1 on devices where RGMII2
pins are available. This achieves 2 Gbps total bandwidth to the CPU using
the second RGMII.
The ports called "wan" are muxed where possible. On a minority of devices,
this is not possible. Those cases:
mt7621_ampedwireless_ally-r1900k.dts: lan3
mt7621_ubnt_edgerouter-x.dts: eth0
mt7621_gnubee_gb-pc1.dts: ethblue
mt7621_linksys_re6500.dts: lan1
mt7621_netgear_wac104.dts: lan4
mt7621_tplink_eap235-wall-v1.dts: lan0
mt7621_tplink_eap615-wall-v1.dts: lan0
mt7621_ubnt_usw-flex.dts: lan1
The "wan" port is just what the vendor designated on the board/plastic
chasis of the device. On a technical level, there is no difference between
a lan and wan port on MT7621AT, MT7621DAT and MT7621ST SoCs. Prefer
connecting to WAN via the port described above for these devices to benefit
the feature brought with this patch.
mt7621_d-team_newifi-d2.dts cannot benefit this feature, although it looks
like it should, because the rgmii2 pins are wired to unused components.
Tested on a range of devices documented on the GitHub PR.
Link: https://github.com/openwrt/openwrt/pull/10238
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Specifications:
SoC: MediaTek MT7621ST (880 MHz)
FLASH: 16 MiB (Macronix MX25L12835FM2I-10G)
RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
WiFi: MediaTek MT7603EN bgn 2x2:2
WiFi: MediaTek MT7612EN an 2x2:2
BTN: Reset, WPS
LED: - Power
- WiFi 2.4 GHz
- WiFi 5 GHz
- WAN
- LAN {1-4}
- USB {1-2}
UART: UART is present as pin hole next to the aluminium capacitor.
3V3 - RX - GND - TX / 115200-8N1
3V3 is the nearest on the aluminium capacitor and nut hole (pin1).
USB: 2 ports
POWER: 12VDC, 1.5A (Barrel 5.5x2.1)
Installation:
Via TFTP:
Set your computers IP-Address to 192.168.1.75
Power up the Router with the Reset button pressed.
Release the Reset button after 5 seconds.
Upload OpenWRT sysupgrade image via TFTP:
tftp -4 -v -m binary 192.168.1.1 -c put IMAGE
MAC addresses:
0x4 *:98 2g/wan, label
0x22 *:9c
0x28 *:98
0x8004 *:9c 5g/lan
Though addresses are written to 0x22 and 0x28, it appears that the
vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the
same here.
Signed-off-by: Pavel Chervontsev <cherpash@gmail.com>
[add MAC address overview, add label-mac-device, fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
