Commit Graph

20844 Commits

Author SHA1 Message Date
Chuanhong Guo
0ab9f283f7 ramips: add support for TOTOLINK LR1200
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
        5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot

Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1

Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
   (e.g. minicom or screen). All 4 serial ports of the modem
   should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
   AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
   recognized.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:26:33 +02:00
Rytis Zigmantavičius
64493d42b4 ath79: add support for 8devices Carambola2 development board
Specifications:
- Atheros AR9331 (400 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 1T1R 2.4 Wlan (AR9331)
- 2x 10/100 Mbps Ethernet
- 3x LEDs, 1x gpio button
- 1x USB 2.0, 5V
- UART over usb, 115200n8

Upgrading from ar71xx target:
- Put image into board:
    scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \
        root@192.168.1.1/tmp/
- Run sysupgrade
    sysupgrade /tmp/sysupgrade.bin

Upgrading from u-boot:
- Set up tftp server with sysupgrade.bin image
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
    setenv serverip 192.168.1.254
- Set device ip from same subnet
    setenv ipaddr 192.168.1.1
- Copy new firmware to board
    tftpboot 0x81000000 sysupgrade.bin
- erase flash
    erase 0x9f050000 +${filesize}
- flash firmware
    cp.b 0x81000000 0x9f050000 ${filesize}
- Reset board
    reset

Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com>
[wrapped long line in commit description, whitespace and art address
 fix in DTS, keep default lan/wan setup, removed -n in sysupgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:24:45 +02:00
Kristian Evensen
046263095e ath79: Add support for ZBT-WD323
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:

* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)

Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232

Intallation and recovery:

The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated.  The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).

While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware.  Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.

Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:24:36 +02:00
Chuanhong Guo
c3a8518918 ath79: fix default config for devices with eth0/eth1 swapped
also fix the following problems in this commit:
glinet,gl-ar150: This router uses an uncommon order of setting up gmacs
                 in ar71xx. gmac0 is preferred to be wan port because of
                 the additional link status info available. So this
                 router will have eth0/eth1 swapped comparing to ar71xx.
tplink,tl-wr710n-v1: same as gl-ar150
embeddedwireless,dorin: eth0 is used as switch port, which was incorrect.
                        It's correct now, so keep this one untouched.
tplink,tl-wr842n-v1: we don't swap PHYs on ar7241 so the original port order
                     is incorrect.
reorder archer-a7-v5 entry.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:12:31 +02:00
Chuanhong Guo
8dde11d521 ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi
With a proper probe deferring for ag71xx we don't need to explicitly
probe mdio1 before gmac0.
Drop all "simple-mfd" in SoC dtsi so that gmac orders can be the same
as ar71xx.
This makes eth0/eth1 order the same as those in ar71xx, which means
we don't need a migration script for this anymore and we can merge
incorrectly split gmac/mdio driver back together.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:12:31 +02:00
Chuanhong Guo
32817580e7 ath79: ag71xx: defer probe if of_phy_connect failed
gmac0 may need a phy on builtin switch, which can be unavailable
if gmac0 is probed before builtin switch.
Return -EPROBE_DEFER in this case so that gmac0 can be probed
later.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:12:31 +02:00
Chuanhong Guo
f84715d463 ath79: rework LED configurations for tplink,archer-d50-v1
The original one has the following problem:
1. Port mask of lan led includes wan port.
2. By using netdev trigger with vlan port, the link led
   is always on.

This commits fixes the above problems by correcting port
mask for lan led and use swconfig trigger for wan leds.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:12:31 +02:00
Pawel Dembicki
9b7abd9fe2 ramips: mt7620: fix 5GHz WiFi LED on DWR-118-A1
Support for D-Link DWR-118 A1 was added before LEDs feature
in mt76x0e driver.

This fixes the 5GHz WiFi LED which was previously inverted.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-06-05 10:12:30 +02:00
Petr Štetiar
971d358579 ar71xx: ag71xx: update ethtool support
Remove references to broken and mostly deprecated phy_ethtool_ioctl, use
new {s,g}et_link_ksettings and add nway_reset which was previously
handled in phy_ethtool_ioctl.

Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Petr Štetiar
206af613b2 ath79: ag71xx: update ethtool support
ethtool doesn't work currently as phy_ethtool_ioctl expects user space
pointer, but it's being passed kernel one. Fixing it doesn't make sense
as {s,g}et_settings were deprecated anyway.  So let's rather remove
phy_ethtool_ioctl and use new {s,g}et_link_ksettings instead. While at
it, update nway_reset as well.

Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Petr Štetiar
eafe0611d9 ar71xx: ag71xx: remove unused SIOCETHTOOL ioctl handling
This ioctl is currently routed through generic interface code:

  dev_ioctl
    dev_ethtool
      __ethtool_get_link_ksettings
        phy_ethtool_ioctl

Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Petr Štetiar
5fee0a0923 ath79: ag71xx: remove unused SIOCETHTOOL ioctl handling
This ioctl is currently routed through generic interface code:

 dev_ioctl
   dev_ethtool
     __ethtool_get_link_ksettings
       phy_ethtool_ioctl

Cc: John Crispin <john@phrozen.org>
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Petr Štetiar
bf58bc3bd8 ramips: ethernet: remove unused SIOCETHTOOL ioctl handling
This ioctl is currently routed through generic interface code.

  dev_ioctl
    dev_ethtool
      __ethtool_get_link_ksettings
        phy_ethtool_ioctl

Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Petr Štetiar
52156b4968 kernel: generic: remove broken and obsolete phy_ethtool_ioctl
Remove 701-phy_extension.patch from 4.14 and 4.19 kernel, as it's
currenlty broken and fixing doesn't make sense as most of it is
deprecated anyway.

Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Koen Vandeputte
3209f5ae3d kernel: bump 4.19 to 4.19.47
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-03 17:00:29 +02:00
Koen Vandeputte
794771afde kernel: bump 4.14 to 4.14.123
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-03 17:00:29 +02:00
Koen Vandeputte
405e08bee6 kernel: bump 4.19 to 4.19.46
Refreshed all patches.

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-03 12:40:53 +02:00
Koen Vandeputte
8f6fd53db9 kernel: bump 4.14 to 4.14.122
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-03 12:40:53 +02:00
Koen Vandeputte
a0f7bdfc71 kernel: bump 4.9 to 4.9.179
Refreshed all patches.

Compile-tested: ar7
Runtime-tested: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-03 12:40:53 +02:00
Christian Lamparter
06e63aad57 apm821xx: backport accepted linux-crypto patches to 4.19
This patch brings the crypto4xx driver up to the latest
upstream changes.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-06-02 11:08:38 +02:00
Christian Lamparter
dfa86b01e5 apm821xx: backport accepted linux-crypto patches to 4.14
This patch brings the crypto4xx driver up to the latest
upstream changes.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-06-02 11:08:38 +02:00
Christian Lamparter
1544df0d89 apm821xx: MX60: convert to interrupt-driven gpio-key driver
This patch converts the device to use the gpio-key
over gpio-key-polled driver.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-06-02 11:08:37 +02:00
Christian Lamparter
651adad603 apm821xx: MR24: convert to interrupt-driven gpio-key driver
This patch converts the device to use the gpio-key
over gpio-key-polled driver.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-06-02 11:08:37 +02:00
Christian Lamparter
9148cbcb7b apm821xx: WNDAP6X0: convert to interrupt-driven gpio-key driver
This patch converts the device to use the gpio-key
over gpio-key-polled driver.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-06-02 11:08:37 +02:00
David Bauer
b8236e102c ath79: fix QCA955x GMAC register size
The register size of the QCA955x currently matches the size stated in
the datasheet. However, there are more hidden GMAC registers which are
needed for the SGMII workaround to work.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-06-02 11:08:37 +02:00
Jan Hoffmann
085f66de9a ramips: create R6220 dtsi and improve WNDR3700v5 support
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.

Performed cleanup:
 * generic DTS node names
 * regulator for usb power
 * added missing pinctrl groups
 * use switch port instead of VLAN as trigger for WAN LED

Fixes for WNDR3700v5:
 * all LEDS work
 * correct ethernet MAC addresses

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-31 11:21:22 +02:00
Markus Scheck
5ff5c9bce6 ramips: add support for Xiaomi Mi Router 4A (100M Edition)
- SoC:      MediaTek MT7628AN
- Flash:    16MB (Winbond W25Q128JV)
- RAM:      64MB
- Serial:   As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0:    MT7628AN 2.4GHz 802.11b/g/n
- WIFI1:    MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable power-LED (two-colored, yellow/blue)
            Non-programmable internet-LED (shows WAN-activity)
- Buttons:  Reset

INSTALLATION:

1. Connect to the serial port of the router and power it up.
   If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
       > Erasing SPI Flash...
       > raspi_erase: offs:20000 len:10000
   occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
   write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
   Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.

Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
2019-05-31 11:21:22 +02:00
David Santamaría Rogado
4d6da05683 ath79: add leds migrations for archer-c7-v2 and v4
In ar71xx v2 has blue color defined because the same mach-*.c is also used
for TL-WDR4900 model with blue leds. ath79 v2 dts defines them as green.

For v4 the situation is the same as v5 so the conversion is identical only
v4 instead v5.

So now upgrading from ar71xx to ath79 should be also smoother for v2 and v4.

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
2019-05-31 11:21:22 +02:00
Davide Fioravanti
7c91144ae6 ramips: add CUDY WR1000 support
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas

Specifications:

MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button

Known issues:
The Power LED is always ON, probably because it is connected
directly to power.

Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.

Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.

Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
  WR1000_EU_92.122.2.4987.201806261618.bin
  WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.

1) Download the original FW from the Cudy website.

   (For example WR1000_EU_92.122.2.4987.201806261618.bin)

2) Remove the header.

   dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64

3) XOR the new file with the region key.

   FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
   FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C

   You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:

   xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..

   Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
   https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)

4) Check the resulting decrypted image.

   Check if bytes from 0x20 to 0x3f are:
   4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00

   Alternatively, you can use u-boot's tool dumpimage tool to check
   if the decryption was successful. It should look like:

   # dumpimage -l stock-firmware.bin
   Image Name:   Linux Kernel Image
   Created:      Tue Jun 26 10:24:54 2018
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4406635 Bytes = 4303.35 KiB = 4.20 MiB
   Load Address: 80000000
   Entry Point:  8000c150

5) Flash it via forced firmware upgrade and don't "Keep Settings"

   CLI: sysupgrade -F -n stock-firmware.bin

   LuCI: make sure to click on the "Keep settings" checkbox
         to disable it. You'll need to do this !TWICE! because
         on the first try, LuCI will refuse the image and reset
	 the "Keep settings" to enable. However a new
         "Force upgrade" checkbox will appear as well.
         Make sure to do this very carefully!

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
2019-05-31 10:36:36 +02:00
Davide Fioravanti
62ce6d58f2 ramips: unify JCG helper command definition
This patch makes the JCG helper command definition available
for every rampis target

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2019-05-31 10:30:03 +02:00
Christian Lamparter
bd83592fc4 apm821xx: wndr4700: interrupt-driven gpio-keys
This patch fixes the active_low setting and
converts all of the physical keys on the wndr4700
to utilize the interrupt-driven gpio-keys driver
over the polled version.

The sdcard-insertion hack has been removed since the
block-subsystem will now be polling the device instead.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-05-31 10:30:03 +02:00
Sandeep Sheriker M
a765a2178c at91:renaming subtraget legacy to sam9x
renaming subtraget legacy to sam9x for adding new sam9 soc's

Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
2019-05-30 12:12:57 +02:00
Hauke Mehrtens
ab629543c0 gemini: Activate Realtek and vitesse DSA driver again
This activates the wrongly removed DSA drivers again.

Fixes 9ab4d74b5f ("kernel: Move some DSA config options to generic config")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-30 12:12:37 +02:00
Hauke Mehrtens
ed224b1880 at91: Update kernel to version 4.14
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
2019-05-30 12:12:37 +02:00
Hauke Mehrtens
aff084adf3 at91: Merge SAMA5 subtargets
Instead of maintaining 3 very similar subtargets merge them into one.
This does not use the Arm NEON extension any more, because the SAMA5D3
does not support NEON.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
2019-05-30 12:12:37 +02:00
Hauke Mehrtens
28e00650a5 at91: Clean up kernel configuration
This removes some settings which are normally set by the generic
configuration and should not be changed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
2019-05-30 12:12:37 +02:00
Hauke Mehrtens
bf0e4cb13f at91: Refresh kernel configuration
The configuration of the sama5d4 subtarget was used as the default
configuration and then the subtarget configurations were adapted.

The resulting kernel configuration without any extra modules selected is
still the same.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
2019-05-30 12:12:37 +02:00
Alan Swanson
e7bd254ed9 lantiq: BTHOMEHUBV5A: don't power off with restart button
The restart button is currently assigned to KEY_POWER power script but
an easily accessible button immediately powering off the device is
undesirable. Switch to using new KEY_POWER2 reboot script with 5 second
seen delay.

Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
2019-05-30 11:55:50 +02:00
Petr Štetiar
99c52251cc ath79: ecb1750: additional dts fixes
This patch fixes following missing bits:

 - add missing 'compatible' property on firmware partition
 - set vendor partition 'userconfig' read-only

Fixes: 30dcbc741d ("ath79: add support for EnGenius ECB1750")
Signed-off-by: Sven Friedmann <sf.openwrt@okay.ms>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-27 22:44:08 +02:00
Ryan Mounce
6d6985ff0e ath79: add support for WD My Net N750
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n

5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO

Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.

UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX

See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.

Tested sysupgrade + factory flash from WD Emergency Recovery

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2019-05-27 22:44:08 +02:00
Alexander Couzens
c4abaa345c
Revert "base-files: add console to inittab"
This reverts commit cde52cb486.
When using OpenWrt in qemu, the shell is unsuable

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-05-25 08:13:20 +02:00
Linus Walleij
8a83f17b24 gemini: Support sysupgrade on DIR-685
This makes sysupgrade work on the D-Link DIR-685 after
initial factory install.

We create the platform.sh script to support sysupgrade
on more targets as we move on with sysupgrade support.

Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[cleanup in platform.sh, removed superfluous SUPPORTED_DEVICES]
2019-05-23 10:19:52 +02:00
Paul Spooren
cde52cb486
base-files: add console to inittab
When running OpenWrt inside an LXC container no shell is opend as LXC
defaults to a virtual /dev/console.

This patch allows to enter a shell after starting the container via
`lxc-start`, without it is only posible to access a shell on tty1 via
`lxc-console`.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-05-21 14:54:15 +02:00
Alexander Couzens
8357b8131c
ar71xx: wr940 v4/v6: correct lan interface mac address
The vendor firmware only uses two mac addresses, the mac address on the
label and the label + 1. While checking multiple devices, all labels have
even mac addresses. Concluding only 2 address are assigned to a device.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-05-21 14:53:45 +02:00
Koen Vandeputte
8eb7cf0cd7 kernel: bump 4.19 to 4.19.44
Refreshed all patches.

Remove upstreamed:
- 103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-21 09:45:15 +02:00
Koen Vandeputte
f442b306f9 kernel: bump 4.14 to 4.14.120
Refreshed all patches.

Remove upstreamed:
- 103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch
- 060-fix-oxnas-rps-dt-match.patch

Altered patches:
- 0067-generic-Mangle-bootloader-s-kernel-arguments.patch
- 006-mvebu-Mangle-bootloader-s-kernel-arguments.patch
- 996-generic-Mangle-bootloader-s-kernel-arguments.patch

Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-21 09:45:15 +02:00
Alexander Wördekemper
0f6b944c92 ath79: glinet_gl-ar750s: Add USB power & microSD
The GL.iNet AR750S USB and microSD port is currently not working out of
the box.  GPIO 7 is used to control the power of the USB port. Add GPIO
7 as a fixed-regulator for the port.  Also add &usb1 to DTS to get the
microSD port to work.

Signed-off-by: Alexander Wördekemper <alexwoerde@web.de>
2019-05-20 21:25:00 +02:00
Petr Štetiar
2f1a11d008 imx6: apalis: fix config survival after sysupgrade -n
This patch fixes `sysupgrade -n` when flashed with rootfs of the same
size as currently running, so the rootfs_data wouldn't get destroyed and
thus survive reboot. So let's fix it by always cleaning up the content
of the rootfs_data during sysupgrade.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-20 21:19:48 +02:00
Petr Štetiar
4318bba0e9 ath79: add leds migrations for archer-c7-v5
ar71xx uses `archer-c7-v5` for led prefix, but ath79 sticks to more
generic `tplink` as the DTS is reused by more boards, so we need to
perform migrations of the LED names during upgrade.

Cc: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-20 21:19:48 +02:00
Petr Štetiar
73b21559ce ar71xx: set mib-poll-interval on devices with ar8xxx switch
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.

So this patch sets mib-poll-interval to 500ms on devices which are using
ar8xxx switch LEDs trigger, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-05-20 21:19:48 +02:00
Petr Štetiar
00d14635db apm821xx: set mib-poll-interval on emac0 attached ar83xx switch
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.

So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to emac0, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-20 21:19:48 +02:00
Petr Štetiar
6648e9458f ath79: set mib-poll-interval on mdio0 attached ar83xx switch
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.

So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to mdio0 bus, as the same value was set for
built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin
switch").

Some measurements performed on TP-Link Archer C7-v5:

 mib-type=0, mib-poll-interval=500ms (10s pidstat)

  Average:  %usr %system  %guest   %wait    %CPU   CPU  Command
  Average:  0.00    1.93    0.00    0.00    1.93     -  kworker/0:2

  iperf3 (30s): 334 Mbits/sec

 mib-type=0, mib-poll-interval=2s (10s pidstat)

  Average:  %usr %system  %guest   %wait    %CPU   CPU  Command
  Average:  0.00    1.14    0.00    0.00    1.14     -  kworker/0:2

  iperf3 (30s): 334 Mbits/sec

So it seems like we get 4x faster LED refresh rate for additional 0.8%
CPU load.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-20 21:19:48 +02:00
Chuanhong Guo
01c0d7f86f generic: ar8216: group MIB counters and use two basic ones only by default
There are too many MIB counters that almost nobody needs since commit
d6366ce366 ("generic: ar8216: mib_work_func: read all port mibs
everytime").

In the worker function to poll MIB data, it deals with all ports instead
of only one port every time, which introduces too many mdio operations
that it becomes a heavy CPU load even on not-emulated MDIO bus.

This commit groups MIB counters and enable only TxBytes and RxGoodBytes
by default (both of which are necessary to get swconfig led working.)
and adds an swconfig attribute to allow enabling all counters if users
need them.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-05-20 21:17:57 +02:00
Chuanhong Guo
107dc4326c generic: ar8216: add mib_poll_interval switch attribute
This allows specifying interval of polling MIB counters from userspace
and allow completely turning off MIB counter support by setting
mib_poll_interval to 0.

Since MIB counter polling is a heavy CPU load for GPIO emulated MDIO
bus, disable this behavior by default. Those who wants to use swconfig
LEDs can enable them with qca,mib-poll-interval dts property or with
swconfig command.

Fixes: FS#2230 ("kworker spikes 100% cpu every 2 second.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-05-20 21:17:45 +02:00
Christian Lamparter
2d0c0abf5d apm821xx: WNDR4700: remove obsolete sd-card change detection
The SD-Card polling is now implemented by default in the
fs-tools block-mount utility package. It might not be as
fast as the current detection method since the polling
time is 2 Seconds, but it's much less of an hack.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-05-19 12:29:24 +02:00
Christian Lamparter
00db985ba8 ath79: convert WD MyNet Range Extender to gpio-keys
This patch converts the Range Extender to use the
interrupt-driven gpio-keys driver over the polled variant.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-05-18 17:59:49 +02:00
Christian Lamparter
ba68afa204 ath79: convert Netgear WNDR3700 series to gpio-keys
This patch converts the WNDR3700 to use the interrupt-driven
gpio-keys driver over the polled variant.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-05-18 17:59:49 +02:00
Christian Lamparter
1e52eacc42 ath79: use the qca,qca9563 chip compatible for the WR818
All other QCA9563 devices already use this identifier for
the exact SoC. Not that this matters much since as upstream
states in Documentation/devicetree/usage-model.txt:

"First and foremost, the kernel will use data in the DT to
identify the specific machine.  In a perfect world, the
specific platform shouldn't matter to the kernel because all
platform details would be described perfectly by the device
tree in a consistent and reliable manner.

[...]

In the majority of cases, the machine identity is irrelevant,
and the kernel will instead select setup code based on the
machine's core CPU or SoC."

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-05-18 17:59:49 +02:00
Nicholas Smith
73e0f52b6e ramips: add support for Telco Electronics X1
Hardware:
SoC:   MT7621
DRAM:  256MB DDR3
Flash: 16MB SPI-NOR
WiFi:  2.4GHz: MT7603 @ PCIe0
WiFi:  5.8GHz: MT7612 @ PCIe1
Modem: Sierra Wireless MC74xx

Interfaces:
GBE RJ45 x5
mPCIe    x2
UART     x1
I2C      x1
JTAG     x1
UIM      x1
LEDs     x6

Flash instructions:
Flash from within the factory bootloader, firmware web interface or CLI using
sysupgrade -F -n

Signed-off-by: Nicholas Smith <mips171@icloud.com>
2019-05-18 17:59:49 +02:00
Davide Fioravanti
f5d2c91415 ath79: add support for TP-Link Archer D50 V1
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.

Internally eth0 is connected to the Broadcom CPU.

Router section - Specification:

CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB

Known issues:
DSL not working (eth0) (WIP)

UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC

J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX

The following instructions require a connection to the J2 UART header.

Flash instruction under U-Boot, using UART
------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
	erase 0x9f020000 +$filesize
	cp.b 0x81000000 0x9f020000 $filesize
	reset

Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
	bootm 0x81000000

Restore the original firmware
-----------------------------
 0. Backup every partition using the OpenWrt web interface
 1. Download the OEM firmware from the TP-Link website
 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
 3. Remove the U-Boot and the Broadcom image part from the file.
    Issue the following command:
	dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
 4. Double check the .mod file size. It must be 7995392 bytes.
 5. Flash it using the OpenWrt web interface. Force the update if needed.
    WARNING: Remember to NOT keep settings.

 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
     Issue below commands in the U-Boot:
        tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
        erase 0x9f020000 +$filesize
        cp.b 0x81000000 0x9f020000 $filesize
        reset

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
2019-05-18 17:59:49 +02:00
Chris Blake
aee5c98619 ath79: add support for Aruba AP-105
SoC: Atheros AR7161-8C1A @ 680 MHz
RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G
NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR)
WI1: Atheros AR9223-AC1A 802.11bgn
WI2: Atheros AR9220-AC1A 802.11an
ETH: Atheros AR8021-BL1E + PoE
LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G
BTN: 1 x Reset
I2C: AT97SC4303s TPM (needs driver!)
CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud

Factory installation:

 - Needs a u-boot replacement. See Wiki for
   information on how to do a in-circut flash with
   a SPI-Flasher like a CH314A or flashrom. Wiki page
   can be found at https://openwrt.org/toh/aruba/aruba_ap-105

 - Be careful when dis- and reassembling the device to
   not squish any of the antenna cables in the process!

 - Be sure to make a full 16 MiB backup of your device
   before flashing the new u-boot! This is needed if you
   ever have interest in reverting back to stock firmware.

Not working:

 - TPM (needs a driver)

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2019-05-18 16:44:41 +02:00
Jan Hoffmann
2fdd02cc7c ramips: add factory image for WNDR3700v5
This uses the existing rules for Sercomm factory images and moves them
to the ramips image Makefile, so they can be used in all subtargets.

The new factory image for WNDR3700v5 can be flashed using nmrpflash.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-18 16:44:41 +02:00
Adrian Schmutzler
d4b89b7170 ath79: Add support for TP-Link TL-WR1043N v5
Specifications:

 - QCA9563 at 775 MHz
 - 64 MB RAM Zentel A3R12E40CBF-8E
 - 16 MB flash Winbond W25Q128FVSG
 - 3 (non-detachable) Antennas / 450 Mbit
 - 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
 - reset and Wi-Fi buttons

TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option. It also has different partitioning scheme.

The software is more in line with the Archer series in that it uses a
nested bootloader scheme.

(This has been adapted from the OpenWrt Wiki page)
<https://openwrt.org/toh/tp-link/tl-wr1043nd>

Installation on HW rev.5:

Factory firmware can be installed via the WEB interface.

Alternatively, it is also possible to use a TFTP server
for recovery purposes:
 - Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin
 - Set static IP of your PC to *192.168.0.66*
 - Router will obtain IP 192.168.0.86 for a few seconds while
   loading, when reset button pressed at power On.

And finally, there's always u-boot access through the UART.
For information visit the wiki.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message]
2019-05-18 16:38:18 +02:00
Adrian Schmutzler
78ea648a3a ath79: Move TL-WR1043ND v1 definition to companions
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-18 16:38:18 +02:00
Adrian Schmutzler
696e6069a4 ath79: Move settings specific for TP-Link TL-WR1043ND v4 to DTS
This prepares for support of v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-18 16:38:18 +02:00
Linus Walleij
76338fded0 gemini: Fix up firmware checksum on DIR-685
Using the same method as the D-Link DAP-2695 A1 we use
the "mtd" tool to augment the firmware checkum in flash
on first boot of a new firmware on the D-Link DIR-685.
We need to augment the Makefile for "mtd" to build in
the special WRGG fixup support for Gemini as well.

This works around the problem of the machine not booting
after factory install unless the sysupgrade is applied
immediately.

Based on commit e3875350f3
"ar71xx: add support for D-Link DAP-2695 rev. A1"

Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-18 16:37:30 +02:00
Liu Yu
671c9d16e3 ramips: add support for HILINK HLK-7628N
Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       128 MB
Flash:     32 MB
WIFI:      802.11n/g/b 20/40 MHz
Ethernet:  5 Port ethernet switch
UART:      2x

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.
5. After firmware is started connect via ethernet at 192.168.1.1

Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
2019-05-18 13:43:55 +02:00
sven friedmann
30dcbc741d ath79: add support for EnGenius ECB1750
Specification:

- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)

https://fccid.io/A8J-ECB1750

Tested and working:

- lan, wireless, leds, sysupgrade (tftp)

Flash instructions:

1.) tftp recovery

- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade

2.) oem webinterface factory install (not tested)

Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".

3.) oem webinterface command injection

OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.

https://openwrt.org/toh/engenius/engenius_ecb1750_1

Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
2019-05-18 13:43:55 +02:00
Jeff Kletsky
819e7946b0 ipq40xx: Add support for Linksys EA8300 (Dallas)
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.

Installation:

  "Factory" images may be installed directly through the OEM GUI.

Hardware Highlights:

  * IPQ4019 at 717 MHz (4 CPUs)
  * 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
  * 256 MB RAM
  * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
      * 2.4 GHz radio at 30 dBm
      * 5 GHz radio on ch. 36-64 at 23 dBm
      * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
      #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
      * All two-stream, MCS 0-9
  * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
  * USB3, single port on rear with LED
  * WPS and reset buttons
  * Four status lights on top
  * Serial pads internal (unpopulated)

  "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"

Implementation Notes:

  The OEM flash layout is preserved at this time with 3 MB kernel and
  ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
  syscfg (56 MB) partitions are untouched, available as read-only.

Serial Connectivity:

  Serial connectivity is *not* required to flash.

  Serial may be accessed by opening the device and connecting
  a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
  including the ability to load images over TFTP and
  either run or flash them.

  Looking at the top of the board, from the front of the unit,
  J3 can be found on the right edge of the board, near the rear

      |
   J3 |
  |-| |
  |O| | (3.3V seen, open-circuit)
  |O| | TXD
  |O| | RXD
  |O| |
  |O| | GND
  |-| |
      |

Unimplemented:

    * serial1 "ttyQHS0" (serial0 works as console)
    * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)

Other Notes:

    https://wikidevi.com/wiki/Linksys_EA8300 states

        FCC docs also cover the Linksys EA8250. According to the
	RF Test Report BT BR+EDR, "All models are identical except
	for the EA8300 supports 256QAM and the EA8250 disable 256QAM."

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-05-18 13:43:54 +02:00
Jeff Kletsky
b3770eaca3 mtd: base-files: Unify dual-firmware devices (Linksys)
Consistently handle boot-count reset and upgrade across
ipq40xx, ipq806x, kirkwood, mvebu

Dual-firmware devices often utilize a specific MTD partition
to record the number of times the boot loader has initiated boot.

Most of these devices are NAND, typically with a 2k erase size.
When this code was ported to the ipq40xx platform, the device in hand
used NOR for this partition, with a 16-byte "record" size. As the
implementation of `mtd resetbc` is by-platform, the hard-coded nature
of this change prevented proper operation of a NAND-based device.

* Unified the "NOR" variant with the rest of the Linksys variants

* Added logging to indicate success and failure

* Provided a meaningful return value for scripting

* "Protected" the use of `mtd resetbc` in start-up scripts so that
   failure does not end the boot sequence

* Moved Linksys-specific actions into common `/etc/init.d/bootcount`

For upgrade, these devices need to determine which partition to flash,
as well as set certain U-Boot envirnment variables to change the next
boot to the newly flashed version.

* Moved upgrade-related environment changes out of bootcount

* Combined multiple flashes of environment into single one

* Current-partition detection now handles absence of `boot_part`

Runtime-tested: Linksys EA8300

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch.pl fixes, traded split strings for 80+ chars per line]
2019-05-18 13:43:51 +02:00
Luis Araneda
250bbaf360 zynq: make title consistent for all devices
Modify the title to match the following format, as it's enough
to uniquely identify a device:
<manufacturer> <model>

This matches what's done for other targets and has the
added benefit of creating a sorted-by-manufacturer list
of devices on menuconfig

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2019-05-17 21:41:43 +02:00
Kristian Evensen
869376710d ramips: Add support for ZBT WE826-E
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:

- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button

The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button

Installation and recovery:

In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address.  Upload the firmware to start the recovery
process.

How to swap SIMs:

You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-05-17 21:41:43 +02:00
Kristian Evensen
52b59a984f ramips: Add support for Head Weblink HDRM200
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:

- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)

Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button

Installation instructions:

Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:

* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.

The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.

Notes:

- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-17 21:41:43 +02:00
Chuanhong Guo
fc553c7e4c ath79: drop unused/incomplete dts
These dts itself are incomplete (e.g. missing mtd partitions) and its
deivce support is never added to ath79 target.
Drop these unused dts for now.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-05-17 21:41:42 +02:00
Petr Štetiar
8be66c2332 ath79: ar9330: fix switch_led_disable_pins reg value
In commit e9652e1696 ("ath79: fix pinmux for ar933x devices") I've
wrongly changed desired register value to 0xf8 although it should've
been set to 0x0.

0xf8 value sets bits 3-7 (ETH_SWITCH_LEDx_EN) to 1 which actually
enables ethernet switch LEDs, so 0x0 is correct value in order to use
the pins as GPIO.

Fixes: e9652e1696 ("ath79: fix pinmux for ar933x devices")
Reported-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-17 21:41:42 +02:00
Petr Štetiar
e2c0a2cb95 ath79: archer-x7-v5: sync ar8327 initial reg values with ar71xx
Simply dumped content of this regs in ar71xx and wrote them to DTS, as a
result port 6 on the switch will appear disconnected as on Archer C7v4.

[AS: testing and PORT6_STATUS fix]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-17 21:41:42 +02:00
Adrian Schmutzler
33ce2ad3e7 ath79: Add missing reset button for TP-Link CPE210 v2 and v3
Reset button support seems to be missing in ath79.

Run-tested on CPE210 v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-15 13:34:24 +02:00
Paul Wassi
e9652e1696 ath79: fix pinmux for ar933x devices
Properly disable the SoC's internal Switch LEDs on the pinmux.
Devices that previously called ath79_gpio_function_disable for
the switch LEDs, just need to reference switch_led_pins in the
pinctrl-0 property of the gpio-leds node.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[changed desired pinctrl register value from 0x1f to proper 0xf8]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[renamed pinmux name to switch_led_disable_pins to make purpose more clear]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-15 13:34:24 +02:00
Petr Štetiar
0aa59e81b3 ath79: archer-x7-v5: remove confusing ar8327 initvals for LEDs
This devices have LEDs connected to the SoC's GPIOs, so it makes no
sense to fiddle with ar8327 LED regs.

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-15 13:34:24 +02:00
Adrian Schmutzler
f32e05c541 ar71xx: Fix network setup for TP-Link Archer C25 v1
Network for the Archer C25 v1 is set up without switch for no
obvious reason. The LED setup is even done switch-based.

This patch changes network setup so a switch is created.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-15 13:34:24 +02:00
Tomasz Maciej Nowak
e7756974aa tegra: add vendor string to device name
for better identification. Also create SUPPORTED_DEVICES string from it
which corresponds to dts compatible string.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-15 13:34:23 +02:00
Josef Schlehofer
eb7eed416b mvebu: add kmod-i2c-mux-pca954x for Turris Omnia
The driver is for the I2C mux.
Schematic available at https://doc.turris.cz/doc/_media/rtrom01-schema.pdf

Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Tested-by: Rosen Penev <rosenp@gmail.com>
2019-05-15 13:34:23 +02:00
Stijn Segers
5cd49395d3 lantiq/xrx200: enable initramfs images
Commit eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL"), but
one needs an initramfs image to flash OpenWrt from stock firmware (as
described in the commit log). This patch has the initramfs image built
by default.

Thanks to blogic (for pointing to the FEATURES declaration in the target
Makefiles) and Musashino on the forum for suggesting
config/Config-images.in needed editing too. While at it, reorder the
TARGET_INITRAMFS_COMPRESSION_LZMA declarations alphabetically.

This patch will result in initramfs images for all lantiq subtargets
that have the ramdisk flag set. I tested on the falcon and ase
subtargets, which lack that flag, to confirm they don't produce any
initramfs images with this patch - which they do not.

Given the limited scope of the lantiq (sub)target(s), blogic indicated
this should be OK.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[fixed the wrong reference to eae6cac6a3 commit]
2019-05-15 13:34:23 +02:00
Hauke Mehrtens
38666e8ae4 malta: Deactivate MIPS O32 and N32 support
OpenWrt is completely compiled from sources using a 64 bit compiler, we
do not need support for the old 32 bit MIPS interface on 64 Bit CPUs,
deactivate it.

Fixes: 46af22de16 ("kernel: Remove CONFIG_COMPAT")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-14 21:50:42 +02:00
Hauke Mehrtens
529c3477b9 octeon: Deactivate MIPS O32 and N32 support
OpenWrt is completely compiled from sources using a 64 bit compiler, we
do not need support for the old 32 bit MIPS interface on 64 Bit CPUs,
deactivate it.

Fixes: 46af22de16 ("kernel: Remove CONFIG_COMPAT")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-14 21:50:42 +02:00
Hauke Mehrtens
77401cdc40 octeon: Refresh kernel configuration
This refreshes the kernel configuration with "make kernel_oldconfig"

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-14 21:50:27 +02:00
Hauke Mehrtens
9ab4d74b5f kernel: Move some DSA config options to generic config
This moves some new configuration options to the generic kernel
configuration instead of configuring them for each target on our own.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-14 21:11:58 +02:00
Jonas Gorski
3611cfe73d brcm63xx: fixup broken patch after kernel bump
Fixes the following compilation issue that was introduced with the bump
to 4.14.118:

  CC      drivers/gpio/gpiolib-of.o
drivers/gpio/gpiolib-of.c: In function 'of_gpiochip_add':
drivers/gpio/gpiolib-of.c:510:12: error: too few arguments to function 'of_gpiochip_scan_gpios'
   status = of_gpiochip_scan_gpios(chip);
            ^~~~~~~~~~~~~~~~~~~~~~
drivers/gpio/gpiolib-of.c:247:5: note: declared here
 int of_gpiochip_scan_gpios(struct gpio_chip *chip, unsigned int start,
     ^~~~~~~~~~~~~~~~~~~~~~
scripts/Makefile.build:326: recipe for target 'drivers/gpio/gpiolib-of.o' failed

Fixes: 09050b6fe2 ("kernel: bump 4.14 to 4.14.118")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2019-05-14 13:15:11 +02:00
Koen Vandeputte
86fd8cb435 kernel: bump 4.19 to 4.19.42
Refreshed all patches.

Remove upstreamed:
- 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch
- 400-v5.2-leds-trigger-netdev-fix-refcnt-leak-on-interface-ren.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
Koen Vandeputte
09050b6fe2 kernel: bump 4.14 to 4.14.118
Refreshed all patches.

Remove upstreamed:
- 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch

Altered:
- 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
Koen Vandeputte
461ef39345 kernel: bump 4.9 to 4.9.175
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
Koen Vandeputte
762361a79c brcm63xx: remove kernel 4.9 support
This target got bumped to 4.14 a long time ago
in commit: 2308b87204

Remove all leftover 4.9 files.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
Hauke Mehrtens
655fff1571 kernel: Fix build of omap target
CONFIG_HW_RANDOM_OMAP is not set to any value after kmod-random-omap was
removed, add the configuration option to the generic configuration.

Fixes: cd3b298533 ("omap24xx: Remove unmaintained target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-12 00:05:04 +02:00
Tomasz Maciej Nowak
de3387654b mvebu: add images for additional ESPRESSObin boards
This commit adds support for different iterations of ESPRESSObin.
The added variants are:

ESPRESSObin with soldered eMMC,

ESPRESSObin V7, compared to V5 some passive elements changed and ethernet
ports labels positions have been reversed,

ESPRESSObin V7 with soldered eMMC.

Please refer to:
584d7c5 ("mvebu: new subtarget cortex A53")
for instruction how to boot OpenWrt image placed on SD card. It is
advised for owners of V5 and previous with bootloader based on U-Boot
2015.01, to upgrade the latest version available at:
http://espressobin.net/tech-spec.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Tomasz Maciej Nowak
ee96fa15b1 mvebu: use device-tree board detection
Convert whole target to Device Tree based board detection instead of
identifying devices by dts file name. With this we can drop mvebu.sh
translation script and rely on common method for model detection.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Tomasz Maciej Nowak
a39d2a8053 mvebu: align device names to vendor_device format
Add vendors in device names and also rename few device names, for easier
identyfying potential firmware to flash. The vendor and device string is
mainly derived from model/compatipble string in dts from particular
device, but since not all devices are well described, some of the renames
follow marketing names.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Tomasz Maciej Nowak
30b5554411 mvebu: image: don't create unnecessarily shell variables
Use make syntax to pass the U-Boot image location and boot with root
partitions size, instead of relying on shell functions and variables.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Tomasz Maciej Nowak
9509a6df0b mvebu: image: improve readability of device recipes
Drop overly complex amount of defines wich are referenced in the same
devices pool and move image recipes to common define, since devices not
using them overwrite it.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Tomasz Maciej Nowak
fb005d688e mvebu: image: introduce BOOT_SCRIPT variable
All of U-Boot scripts repeat the same pattern with only Device Tree blob
name changing for respective device. Therefore create generic scripts
which will be altered on demad by image build process, and create
BOOT_SCRIPT variable which can be added to device recipe and will allow
referencing the same script by many device recipes. This will allow to
slim down the ammount of files in buildroot tree and avoid needlessly
incrementing amount of boot scripts if new devices will be added.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Tomasz Maciej Nowak
ef384c68e7 mvebu: image: stack repeated variables
All of arm64 devices have part of variables repeatedly defined. Stack
them to common define, and reference it in each device recipe.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Tomasz Maciej Nowak
f0c2bac252 mvebu: remove unnecessary code building dtbs
Even if dts is not included in upstream Makefile, it is built anyway by
recipe specified in include/image.mk. Also remove Build/dtb, it's not
used since 3f72f3a ("mvebu: clearfog: include DTB for all variants in
image").

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Jeff Kletsky
3bc8ed91d4 generic-4.19: Backport spi-nand support for GigaDevice A/E
This patch backports verbatim the commits from Linux 5.0 and 5.1
that implemented support for GigaDevice SPI NAND A and E variants.

Supported only in Linux 4.19 and later as based on the upstream
drivers/mtd/nand/spi/ framework.

mtd-spinand-add-support-for-GigaDevice-GD5FxGQ4xA.patch
commit c93c613214ac (5.0)

mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UExxG.patch
commit c40c7a990a46 (5.1)

Run-tested-on: GL.iNet AR750S

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-05-11 23:10:10 +02:00
Hauke Mehrtens
747587ec61 kernel: Reorder generic configuration
This was done like this:
./scripts/kconfig.pl '+' target/linux/generic/config-4.14 /dev/null > target/linux/generic/config-4.14-new
mv target/linux/generic/config-4.14-new target/linux/generic/config-4.14

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
87ac3e801d gemini: Make kernel text and rodata read-only
This is activate for all other targets except gemini, also activate it
there.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
f7426b13fa cns3xxx: Activate CONFIG_CPU_SW_DOMAIN_PAN
This is already activated for all other ARM targets

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
2164a7bf15 x86: Activate CONFIG_X86_SMAP
This activates "Supervisor Mode Access Prevention". modern CPUs will
prevent the kernel code from accessing any data from the userspace
without the usage of copy_to_user() or copy_from_user()

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
75eb8a146d kernel: Deactivate CONFIG_BINFMT_MISC
CONFIG_BINFMT_MISC allows it to add support for new executable formats
to the kernel from user space, the kernel will then detect for example a
java binary and call the java execution program automatically. I am not
aware that this feature is used in OpenWrt and this could be used to
exploit something. Deactivate it for all targets for now.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
d4ad7e6548 kernel: Do not set CONFIG_DEVMEM or CONFIG_DEVKMEM
This is deactivated by default and should be manually activated in the
OpenWrt kernel configuration

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
57ec21ef3d kernel: Activate CONFIG_SYN_COOKIES for all targets
Some targets deactivated CONFIG_SYN_COOKIES, for unknown reasons, use
the default setting from the generic configuration which activates
CONFIG_SYN_COOKIES.

This should prevent SYN flooding.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
46af22de16 kernel: Remove CONFIG_COMPAT
This removes support for executing old 32 bit applications on 64 bit ARM
and MIPS kernels.
On OpenWrt we normally compile all the user space applications on our
own and do not support third party binary only modules especial not 32
bit applications on 64 bit CPUs.

This reduces the attack surface on such systems and should also save
some memory.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
7099bf0926 kernel: Remove CONFIG_DEBUG_RODATA and CONFIG_DEBUG_SET_MODULE_RONX
These were renamed to CONFIG_STRICT_KERNEL_RWX and CONFIG_STRICT_MODULE_RWX and are
activated in kernel 4.14 and later by default.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
32eb66881c kernel: Activate CONFIG_ARM64_SW_TTBR0_PAN
This activates "Emulate Privileged Access Never using TTBR0_EL1
switching" on ARM64.

This should prevent the kernel from reading code from user space in
kernel context.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Hauke Mehrtens
9b1239451d Kernel: Activate CONFIG_HARDENED_USERCOPY
This adds additional checks to the copy_from_user() and copy_to_user()
functions. The details are described in this article:
https://lwn.net/Articles/695991/

This should only have a very small performance impact on system calls
and should not affect routing performance.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-11 17:15:41 +02:00
Adrian Schmutzler
d8ec6dee49 ath79: Add missing read-only properties
Add some read-only properties to protect partitions from
accidental changes.

Also fixed two whitespaces error on the way.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-11 16:37:11 +02:00
David Bauer
a4dc519888 ramips: fix R6120 factory image
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.

When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-05-11 16:37:11 +02:00
Klaus Kudielka
0a11c87e46 mvebu: fix board_name condition in 79_move_config
The correct board_name for the Turris Omnia is armada-385-turris-omnia.

Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
2019-05-11 16:37:11 +02:00
Klaus Kudielka
ad62247800 base-files: improve lib/upgrade/common.sh
Recently, upgrade device autodetection has been added to the mvebu target.
This exposes some shortcomings of the generic export_bootdevice function,
e.g. on the Turris Omnia: export_bootdevice silently reports the root
partition to be the boot device. This makes the sysupgrade process fail at
several places.

Fix this by clearly distinguishing between /proc/cmdline arguments which
specify the boot disk, and those which specify the root partition. Only in
the latter case, strip off the partition, and do it consistently.
root=PARTUUID=<pseudo PARTUUID for MBR> (any partition) and root=/dev/*
(any partition) are accepted.

The root of the problem is that the *existing* export_bootdevice in
/lib/upgrade/common.sh behaves differently, if the kernel is booted with
root=/dev/..., or if it is booted with root=PARTUUID=...

In the former case, it reports back major/minor of the root partition,
in the latter case it reports back major/minor of the complete boot disk.

Targets, which boot with root=/dev/... *and* use export_bootdevice /
export_partdevice, have added workarounds to this behaviour, by specifying
*negative* increments to the export_partdevice function.

Consequently, those targets have to be adapted to use positive increments,
otherwise they are broken by the change to export_bootdevice.

Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 16:37:11 +02:00
Steve Glennon
6411eac5da ipq40xx: add factory image for EnGenius ENS620EXT
Extended  mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.

Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.

Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.

Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.

Note that there is currently no method to return to factory firmware,
so this is a one-way street.

Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops

You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.

Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".

Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".

The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)

Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
2019-05-11 16:37:11 +02:00
Steve Glennon
9b0eb4d260 ipq40xx: Fix reboot on EnGenius ENS620EXT
This patch works around an issue where reboot would cause the AP
to power down and not reboot.

The ipq4019 restart controller reboot causes the system
to power down and not recover. Fix is to disable the restart
controller in the device tree and the device reverts to
using the watchdog to perform the reset.

The real problem is due to the buggy bootloader that ships
with the device. Steve Glennon reported in the PR for this
patch: <https://github.com/openwrt/openwrt/pull/2009> that:

"the problem was due to a bad u-boot that ships with the device.

Using the u-boot that comes with 3.5.5.3 EnGenius factory
software now allows the old code (using the do_msm_reboot)
to reboot successfully.

On to the bad news:
Well 3.5.5.3 is a bad path. Finally managed to recover. You
CANNOT use prior EnGenius firmware to downgrade.

Findings:

* They now password protect the serial console with a new, unkown
  password.
* They changed the protection on their walled-garden. I have to
  use the ssh admin@ip /bin/sh --login to get out of their
  walled-garden.
* Attempts to flash the original 3.0.0 or 3.0.1 EnGenius firmware
  fail through the UI and sysupgrade. Their firmware update GUI now
  seem to detect regular openwrt images, but they fail to flash
  Attempts to flash a normal OpenWrt image with sysupgrade fail.
[..]

Attempts to sysupgrade with EnGenius firmware fail with the same
"mandatory section(s) missing" error, so you cannot downgrade to
3.0.0 or 3.0.1."

Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added valuable
findings from github discussion]
2019-05-11 16:37:11 +02:00
Alberto Bursi
4de0a61a62 kirkwood: enable sata port multiplier
Marvell sata controllers in all kirkwood SoCs support
sata port multipliers, just like mvebu.
Enable this feature in the default kernel config
so it is available in normal builds.
tested and working on nsa310b

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2019-05-11 16:37:11 +02:00
Felix Fietkau
85017c40f4 build: add a config option for enabling a testing version of the target kernel
If the target supports a newer kernel version that is not used by default
yet, it can be enabled with this option

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-05-11 11:37:10 +02:00
Deng Qingfang
367813b9b1 ramips: mt7620: fix dependencies
MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware
Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies
according to original Kconfig and lsmod output

This will remove some unnecessary packages from MT7620 target to
save some space

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[75 characters per line in the commit message]
2019-05-11 01:05:11 +02:00
Koen Vandeputte
bc85640cdc kernel: bump 4.19 to 4.19.38
Refreshed all patches.

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-06 12:43:01 +02:00
Koen Vandeputte
07720c392f kernel: bump 4.14 to 4.14.115
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-06 12:43:01 +02:00
Koen Vandeputte
fca966d7b7 kernel: bump 4.9 to 4.9.172
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-06 12:43:01 +02:00
Jeff Kletsky
2437418cd5 ath79: glinet_gl-ar750s: Use QCA9887 firmware
The GL.iNet AR750S is based around the QCA9563
and requires the QCA9887 firmware for operation.

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-05-05 21:11:01 +02:00
Joachim Fünfer
edf1d6264b ar71xx: fix failsafe interface for TL-WR940nv6
Switches failsafe mode interface from WAN to LAN ports.

Tested on TL-WR940Nv6.0 and TL-WR940Nv6.1

Signed-off-by: Joachim Fünfer <joachim.fuenfer@stusta.net>
2019-05-05 21:11:01 +02:00
David Bauer
3364af629d ath79: fix OCEDO Raccoon 10Mbit PLL value
This corrects the PLL value for 10 Mbit/s links on the OCEDO Raccoon.
Prior to this patch, 10 Mbit/s links would not transmit data.

It is worth mentioning that the vendor firmware used the same PLL
settings and 10Mbit/s was also not working there.

All other link-modes are working correctly without any packet loss.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-05-05 21:11:01 +02:00
Rosy Song
3b4c44aa8b ar71xx: mute script error in ar922x-led-fix script
This commit fixes following script error in syslog:

 cat: can't open '/sys/devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.4/ieee80211/phy*/name': No such file or directory
 sh: add: unknown operand
 sh: add: unknown operand

Signed-off-by: Rosy Song <rosysong@rosinson.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[commit subject and message tweaks]
2019-05-05 21:11:01 +02:00
Petr Štetiar
51216b4f83 kernel: Rename UPROBE_EVENT to UPROBE_EVENTS
Upstream has renamed UPROBE_EVENT to UPROBE_EVENTS in the following
commit:

 commit 6b0b7551428e4caae1e2c023a529465a9a9ae2d4
 Author: Anton Blanchard <anton@samba.org>
 Date:   Thu Feb 16 17:00:50 2017 +1100

     perf/core: Rename CONFIG_[UK]PROBE_EVENT to CONFIG_[UK]PROBE_EVENTS

     We have uses of CONFIG_UPROBE_EVENT and CONFIG_KPROBE_EVENT as
     well as CONFIG_UPROBE_EVENTS and CONFIG_KPROBE_EVENTS.

     Consistently use the plurals.

So I'm changing it to this plural option in order to make kconfig happy
and stop asking about it if kernel is compiled with verbose logging:

 Enable uprobes-based dynamic events (UPROBE_EVENTS) [Y/n/?] (NEW)

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-05 14:41:49 +02:00
Hauke Mehrtens
1325e74e0c kernel: Remove support for kernel 3.18
No target is using kernel 3.18 anymore, remove all the generic
support for kernel 3.18.

The removed packages are depending on kernel 3.18 only and are not used on
any recent kernel.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 22:41:38 +02:00
Hauke Mehrtens
675832de79 xburst: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Hauke Mehrtens
cd3b298533 omap24xx: Remove unmaintained target
This target only supports kernel 4.1, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Hauke Mehrtens
8ba38cc145 ppc44x: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Hauke Mehrtens
406a3826dc ppc40x: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Hauke Mehrtens
65cdfbabde mcs814x: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Hauke Mehrtens
e6f9a8e89b au1000: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Hauke Mehrtens
c35425f418 adm8668: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Hauke Mehrtens
2d0a2ff1e0 adm5120: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Koen Vandeputte
49dca520fb brcm2708: fix renamed definition (FS#2265)
This target adds an alternative mmc driver using a patch.
Within this patch, a definition got renamed upstream.

Change it to fix following compile error:

  CC      drivers/mmc/host/bcm2835-mmc.o
In file included from ./include/linux/kernel.h:14:0,
                 from ./include/linux/delay.h:22,
                 from drivers/mmc/host/bcm2835-mmc.c:25:
drivers/mmc/host/bcm2835-mmc.c: In function 'bcm2835_mmc_dumpregs':
drivers/mmc/host/bcm2835-mmc.c:254:27: error: 'SDHCI_ACMD12_ERR' undeclared (first use in this function); did you mean 'SDHCI_CMD_CRC'?
   bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
                           ^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
    printk(fmt, ##__VA_ARGS__); \
                  ^~~~~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:253:2: note: in expansion of macro 'pr_debug'
  pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
  ^~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:254:27: note: each undeclared identifier is reported only once for each function it appears in
   bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
                           ^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
    printk(fmt, ##__VA_ARGS__); \
                  ^~~~~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:253:2: note: in expansion of macro 'pr_debug'
  pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
  ^~~~~~~~
scripts/Makefile.build:326: recipe for target 'drivers/mmc/host/bcm2835-mmc.o' failed
make[8]: *** [drivers/mmc/host/bcm2835-mmc.o] Error 1

Upstream commit:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.14.114&id=45fd8679ea86bffb352132a1df4917c3d11375aa

Fixes: b765f4be40 ("kernel: bump 4.14 to 4.14.114")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-03 16:37:48 +02:00
Koen Vandeputte
08802d93e2 kernel: bump 4.19 to 4.19.37
Refreshed all patches.

Altered patches:
- 150-bridge_allow_receiption_on_disabled_port.patch
- 201-extra_optimization.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-02 12:59:26 +02:00
Koen Vandeputte
b765f4be40 kernel: bump 4.14 to 4.14.114
Refreshed all patches.

Altered patches:
- 150-bridge_allow_receiption_on_disabled_port.patch
- 201-extra_optimization.patch

Remove upstreamed:
- 022-0006-crypto-crypto4xx-properly-set-IV-after-de-and-encryp.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-02 12:59:26 +02:00
Koen Vandeputte
456f486b53 kernel: bump 4.9 to 4.9.171
Refreshed all patches.

Altered patches:
- 150-bridge_allow_receiption_on_disabled_port.patch
- 201-extra_optimization.patch

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-02 12:59:26 +02:00
Koen Vandeputte
fdf1aae77d kernel: add missing symbol in 4.19 config
Intel AtomISP2 dummy / power-management driver (INTEL_ATOMISP2_PM) [N/m/y/?] (NEW)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-29 15:28:33 +02:00
Felix Fietkau
9af2735734 kernel: fix regression on 4.19 with 613-netfilter_optional_tcp_window_check.patch (FS#2253)
Since ct->proto.tcp.last_win isn't updated when nf_ct_tcp_no_window_check is
enabled, the retransmission timeout check needs to be bypassed.

Based on patch by Rob Mosher

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-04-27 18:58:07 +02:00
Koen Vandeputte
e40050d104 ar71xx: add support for Mikrotik RouterBOARD 2011UiAS-2HnD r2
This board got a new hardware revision, without any change in functionality.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-23 13:22:31 +02:00
Koen Vandeputte
f337cd2ba3 kernel: bump 4.19 to 4.19.36
Refreshed all patches.

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-23 13:22:31 +02:00
Koen Vandeputte
07aaa7e3d6 kernel: bump 4.14 to 4.14.113
Refreshed all patches.

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-23 13:22:31 +02:00
Koen Vandeputte
d27c245216 kernel: bump 4.9 to 4.9.170
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-23 13:22:31 +02:00
Koen Vandeputte
022dfdc41c kernel: bump 4.19 to 4.19.35
Refreshed all patches.

Fixes:
- CVE-2019-3887

New symbol:
- CONFIG_LDISC_AUTOLOAD

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-22 21:15:17 +02:00