Commit Graph

1809 Commits

Author SHA1 Message Date
Felix Fietkau
c1023c8075 mt76: sync with version 878456caf6 from master
Backport required DT changes from commit dabdd123c9.
Significantly improves stability and performance for MT76x2 and MT7603

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-13 11:56:25 +02:00
Thibaut VARENE
f9a849ca84 ramips: mt7620: do not pad sysupgrade Archer images
The current makefile unnecessarily pads sysupgrade image for Archer devices.

This has three implications:
1. higher risk of OOM when uploading the binary image to the device
2. much slower upgrade due to time wasted erasing and writing padding
3. grows image beyond available flash size if metadata are appended

This is already fixed in master, albeit in a completely different way (the
whole target have been reworked)

Fixes: FS#1025, FS#1039

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-10-04 22:22:56 +02:00
Hauke Mehrtens
720b0e2e2d kernel: update 4.4 to 4.4.89
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-09-30 13:58:00 +02:00
David Yang
4f162ac3ce ramips: fix hg255d LED status support
Use the green power LED for boot status indication.

Source: https://my.oschina.net/osbin/blog/278782 Para 3

Signed-off-by: David Yang <mmyangfl@gmail.com>
2017-09-13 08:07:39 +02:00
Kevin Darbyshire-Bryant
4a1b87aba4 kernel: update 4.4 to 4.4.83
Refresh patches.
Minor update 704-phy-no-genphy-soft-reset.patch which was partially
accepted upstream.
Compile-tested on ar71xx.
Runtime-tested on ar71xx.

Fixes the following vulnerabilities:
- CVE-2017-7533 (4.4.80)
- CVE-2017-1000111 (4.4.82)
- CVE-2017-1000112 (4.4.82)

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2017-08-17 19:47:27 +02:00
Mathias Kresin
ff414fb575 ramips: fix WHR-1166D WAN port
By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.

Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.

Fixes: FS#670

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-11 18:13:38 +02:00
Thibaut VARENE
982612dba2 ramips: ArcherC50v1: fix wlan2g MAC address
By default the wlan eprom contains the generic ralink MAC which is not
the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses
are decremented from the ethernet MAC.

This patch fixes the MAC address for wlan2g in line with OFW.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-08-06 09:31:05 +02:00
Mathias Kresin
48798af6d2 ramips: fix Omnima MiniEMBWiFi image
Reference the Omnima MiniEMBWiFi device tree source file in the image
build code. Otherwise the dts of the image processed before is used.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-02 21:16:20 +02:00
Mathias Kresin
1a050c83ac ramips: build HuaWei HG255D image
The code to build an image was disabled some time ago for unknown
reasons albeit the image looks fine.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-02 21:16:20 +02:00
Mathias Kresin
57a8f36ac4 ramips: add missing partitions
The partitions were lost during migration to device tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-02 21:16:20 +02:00
John Crispin
6f4a903533 ralink: fix rcu_sched stalls on mt7621
there were 2 bugs
*) core1 came up with a bad bogo mips, looks like the clock needed time to stabilize
*) HPT frequency was not set making r4k timers not come up properly

Backport of 9551d91b1d "ralink: fix rcu_sched stalls on mt7621".

Signed-off-by: John Crispin <john@phrozen.org>
2017-08-01 06:54:07 +02:00
Thibaut VARENE
c407e6c2f2 ramips: Archer C50v1: fix power led
01_leds had a workaround for the power led to compensate for the
inverted GPIO state. This patch was missing from my previous commit.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[add the power led default-state which was omitted in the last commit
by me]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-29 12:07:16 +02:00
Thibaut VARENE
8e67c358e7 ramips: Archer C50v1: fix switch port numbering
Luci shows switch ports in wrong order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-07-29 09:25:00 +02:00
Thibaut VARENE
a9439344e7 ramips: Archer C50v1: fix LEDs active levels
All LEDs GPIOs are active low on this device.

WAN and POWER states were inverted. Add default state for power.

Tested on Archer C50v1.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-07-29 09:24:59 +02:00
Mathias Kresin
5e409f0e69 ramips: fix Mercury MAC1200R v2.0 board name
With d2b6bf1416 ("ramips: fix image validation errors") the board
name was changed to fix an image validation error. But this change
wasn't applied to all other files using the board name, which broke
sysupgrade.

Revert this change and use the former board name in the metadata
instead.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-29 09:24:59 +02:00
Mathias Kresin
2247af82df ramips: add NULL clock fix send upstream
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.

Fixes: FS#735

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-29 09:24:52 +02:00
Hauke Mehrtens
69acb2533a kernel: update kernel 4.4 to version 4.4.79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-07-28 23:49:35 +02:00
Thibaut VARENE
a5822dbd0f ramips: DIR-860L-B1 fix switch port numbering
Luci shows switch ports in inverted order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-07-25 21:02:27 +02:00
Giuseppe Lippolis
e08b8255ec ramips: fix wps button gpio for DWR-512
The WPS button is at GPIO#7.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-07-25 21:02:27 +02:00
Paul Wassi
ece85e2e49 ramips: DTS: VoCore2 improvements/fixes
The VoCore2 features 128MB of RAM, therefore set
memory in DTS to 128*1024*1024 = 0x8000000
The board's LED is connected to GND, set it to
ACTIVE_HIGH here.
Make serial console working again on kernel 4.9 by
change of pinmux configuration.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-07-25 21:02:27 +02:00
Mathias Kresin
3214e174a0 ramips: fix Xiaomi MiWiFi Nano firmware partition size
Even the commit message of the patch adding support for the MiWiFi Nano
says that a 16 MB flash chip is used. Extend the firmware partition to
make use of all available flash space.

Fixes: FS#622

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-08 08:53:52 +02:00
小桥
2e206c79cc ramips: fix Phicomm K1S(PSG1208) pinmux
Use gpio function for pins with LEDs.

Signed-off-by: 小桥 <29551030@qq.com>
2017-06-12 21:10:14 +02:00
Steffen Weinreich
4bd98e9224 ramips: add om-watchdog to rut5xx DEVICE_PACKAGES
Add om-watchdog as default package for rut5xx.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
2017-05-15 22:56:01 +02:00
Jo-Philipp Wich
7f3ec01069 ramips: fixup-mac-address: add missing include
Add missing include of ramips.sh in order to import the missing
ramips_board_name() procedure.

Fixes FS#774.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-05-11 00:54:06 +02:00
Henryk Heisig
8619683037 ramips: add factory firmware for Tp-Link C20i/C50
TP-Link firmware doesn't accept sysupgrade.bin with metadata.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-05-05 20:00:57 +02:00
Paul Spooren
79cd14152c ramips: enable ramdisk for mt7621
Fixes #758

Signed-off-by: Paul Spooren <paul@spooren.de>
2017-05-04 01:03:25 +02:00
Thibaut VARENE
8b9f7bd7bd ramips: WN3000RPv3: do not setup switch
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.

Configure LAN as eth0 instead.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-04-28 17:10:01 +02:00
Kristian Evensen
49ce6d04b0 ramips: add support for Sanlinking D240
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-04-28 17:09:45 +02:00
Mathias Kresin
7e2ad9cbb8 ramips: fix Sercomm NA930 compatible string
The Sercomm NA930 is not a mt7620a evaluation board and shouldn't use
the eval board compatible string.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-28 17:09:36 +02:00
Mathias Kresin
88cc06abb7 ramips: remove Planex CS-QR10 sound device tree node
The comptible string is neither added by any LEDE patch nor exists in
in the kernel. Drop the sound node which was obviously added
accidentally with 9195d8da ("ramips: DTS rework").

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-28 17:09:29 +02:00
Mathias Kresin
f1f0b92a79 ramips: cleanup SPI flash device tree properties usage
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.

Remove the linux,modalias property. It is obsolete since kernel 4.4.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-28 17:09:24 +02:00
Felix Fietkau
6aa0a85fc6 ramips: remove DT pcie nodes for GL-MT300A/N
These devices don't have a secondary wifi chip

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-04-28 17:09:18 +02:00
Vitaly Chekryzhev
28d626556d ramips: ZyXEL Keenetic Omni/Omni2: export gpio usb power
Export gpio usb to allow power management of USB port.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-04-28 17:09:08 +02:00
Vitaly Chekryzhev
fd693bc0e8 ramips: ZyXEL Keenetic Viva: align factory images
ZyXEL web-flasher requires squashfs to be aligned to 64kb.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-04-28 17:09:02 +02:00
Vitaly Chekryzhev
5b2624d618 ramips: ZyXEL Keenetic Viva: export gpio usb power
Export gpio usb to allow power management of USB port.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-04-28 17:08:56 +02:00
Yo Abe
a66623639a ramips: add ip17xx support to WLI-TX4-AG300N
ramips/rt288x WLI-TX4-AG300N was missing support for its 100Mbit switch which
should be included by default.

Signed-off-by: Yo Abe <abe.geel@gmail.com>
[Jo-Philipp Wich: picked from OpenWrt PR#359, rewrap commit msg, fix Sob]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-04-28 17:08:50 +02:00
Joseph C. Lehner
0405851eb2 ramips: fix EX2700 wireless mac
On some EX2700 devices, the MAC address from the eeprom data differs
from the actual MAC address. Fix that, and cleanup the DTS file
while we're at it.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-04-28 17:08:42 +02:00
Vitaly Chekryzhev
a12655a840 ramips: ZyXEL Keenetic series update wan mac
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-04-28 17:07:48 +02:00
Vitaly Chekryzhev
94948252e2 ramips: ZyXEL Keenetic Omni align factory images
ZyXEL web-flasher requires squashfs to be aligned to 64kb.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-04-28 17:07:42 +02:00
Vitaly Chekryzhev
85bca2d0fb ramips: correct keenetic-series switch index
Fix switch name typo

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-04-28 17:07:35 +02:00
Thibaut VARENE
1aee42c6a9 ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-04-28 17:07:24 +02:00
BangLang Huang
846457fdbf ramips: fix mac address of miwifi-mini
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2017-04-28 17:07:04 +02:00
Furong Xu
0f3c2d031a ramips: Clean duplicated status property for Omega2 WMAC in dtsi
At the tail of dtsi, wmac is enabled twice, clean the first one

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-04-28 17:02:48 +02:00
Giuseppe Lippolis
26f07f668a ramips: fixed sms led polarity into dwr-512 DT
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-04-28 17:02:48 +02:00
Thibaut VARENE
dbd2212205 ramips: WN3000RPv3: do not setup switch
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.

Configure LAN as eth0 instead.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-04-28 17:02:48 +02:00
Matthias Schiffer
9117ef8d6a
ramips: update DEVICE_PACKAGES for Ubiquiti EdgeRouter X
Fixes removal of unneeded kernel modules with per-device rootfs.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-04-22 19:01:21 +02:00
Jo-Philipp Wich
6ca5ccc620 kernel: update kernel 4.4 to 4.4.61
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-04-15 17:20:51 +02:00
Mathias Kresin
f2f672c32c ramips: add RP-N53 pcie wireless eeprom
Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata.
Disable the 2.4GHz band as this band has no antennas attached but is
enabled in the eeprom/caldata.

Fixes: FS#691

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-12 10:13:40 +02:00
Mathias Kresin
f3dc2ffdd4 ramips: fix WHR-600D eeprom dt property
Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as
this board have a RT5592 and uses the rt2x00 driver. The mediathek
device tree bindings do not work here.

Fixes: FS#691

Fixes: d8dd207ea6 ("ramips: use the ralink,mtd-eeprom device tree property")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-12 10:13:37 +02:00
Hauke Mehrtens
0dcc4d239d kernel: update kernel 4.4 to 4.4.59
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-04-02 14:37:49 +02:00