Using the LED of network interfaces for status (boot/failsafe/...)
indication is somewhat misleading, as the blinking might be
mistaken for network activity. This uses rssi LEDs instead, which
do not blink normally and thus are less ambiguous.
The rssihigh LED has also been used consistently for the TP-Link CPE
devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.
Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.
Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as
this one is using ath9k keys.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
This patch adds the label MAC address for several devices in
ath79.
Some devices require setting the MAC address in 02_network:
For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices
For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.
Specifications:
- AR9344 SoC
- 535/400/267 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 5 GHz, up to 25 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while while the WAN LED flashes, until it starts flashing
faster. Once in failsafe mode, perform a factory reset as usual.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and
keep it pressed for >10 seconds. The recovery page will be at
http://192.168.1.1
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
