Images for certain devices are staring to become too large, as some
device only have 6MB available in their vendor partition layout for the
initial install. This is especially pressing for bootloaders only
supporting gzip compression.
Drop some packages from DEFAULT_PACKAGES that aren't strictly required
for a factory install. The user can always install more packages later
using opkg/apk, or via a sysupgrade to a custom build.
firewall4 is kept to ensure the most recent firewall package is selected
in builds including LuCI.
ethtool is kept as a frequently used diagnostics tool.
Link: https://github.com/openwrt/openwrt/pull/17450
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit c9ae39b2d156ff893d88a7d75b9044aac2fdd8d0)
Now that there is 6.6 support for realtek, lets encourage testing it by
making it default so 5.15 can be dropped ASAP.
Link: https://github.com/openwrt/openwrt/pull/16408
Signed-off-by: Robert Marko <robimarko@gmail.com>
Our current Makefiles a little bit messy and can be improved somewhat,
both in whitespace and in style.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
The tc package does not exits any more, it was split into tc-tiny,
tc-full and tc-bpf. Include tc-bpf by default into realtek images.
This increases the compressed image size by about 232KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The realtek target is not a router, but basic device, see DEVICE_TYPE.
The basic device type does not come with firewall by default, see
include/target.mk for details. The realtek target extended
DEFAULT_PACKAGES manually with firewall.
This changes the defaults to take firewall4 and nftables instead of
firewall and iptables. This also adds the additional package
kmod-nft-offload.
The only difference to the router type is the missing ppp,
ppp-mod-pppoe, dnsmasq and odhcpd-ipv6only package.
This increases the compressed image size by about 422KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not include the dnsmasq and odhcpd-ipv6only package by default any
more. These services are not needed on a switch. If someone needs this
it is still possible to use opkg or image builder to add them.
This decreases the compressed image size by about 165KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We add the RTL931X sub-target with kernel configuration for
a dual core MIPS InterAptive CPU.
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
The GS1900-48 is a 48 + 2 port Gigabit L2 switch with 48 gigabit ports.
Hardware:
RTL8393M SoC
Macronix MX25l12805D (16MB flash)
128MB RAM
6 * RTL8218B external PHY
2 * RTL8231 GPIO extenders to control the port LEDs, system LED and
Reset button
2 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules.
Power is supplied via a 230 volt mains connector.
The board has a hard reset switch SW1, which is is not reachable from the outside.
J4 provides a 12V RS232 serial connector which is connected through U8 to
the 3.3V UART of the RTL8393. Conversion is done by U8, a SIPEX 3232EC.
To connect to the UART, wires can be soldered to R603 (TX) and R602 (RX).
Installation:
Install the squashfs image via Realtek's original Web-Interface.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Create the RTL838x specific Makefiles. Move CPU-type into
rtl838x.mk as this is specifc to that platform. Add
rtl838x subtarget into main Makefile.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
realtek target to allow using Kernel 5.10 for testing.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
