The Mikrotik R11e-LTE6 modem is similar to ZTE MF286R modem, added
earlier: it has a Marvel chip, able to work in ACM+RNDIS mode, knows ZTE
specific commands, runs OpenWrt Barrier Breaker fork.
While the modem is able to offer IPv6 address, the RNDIS setup is unable
to complete if there is an IPv6 adress.
While it works in ACM+RNDIS mode, the user experience isn't as good as
with "proto 3g": the modem happily serves a local IP (192.168.1.xxx)
without internet access. Of course, if the modem has enough time
(for example at the second dialup), it will serve a public IP.
Modifing the DHCP Lease (to a short interval before connect and back to
default while finalizing) is a workaround to get a public IP at the
first try.
A safe workaround for this is to excercise an offline script of the
pingcheck program: simply restart (ifdown - ifup) the connection.
Another pitfall is that the modem writes a few messages at startup,
which confuses the manufacturer detection algorithm and got disabled.
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (2366): Failed to parse message data
daemon.notice netifd: mikrotik (2366): WARNING: Variable 'ok' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2366): Unsupported modem
daemon.notice netifd: mikrotik (2426): Stopping network mikrotik
daemon.notice netifd: mikrotik (2426): Failed to parse message data
daemon.notice netifd: mikrotik (2426): WARNING: Variable '*simdetec:1,sim' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2426): Unsupported modem
daemon.notice netifd: Interface 'mikrotik' is now down
A workaround for this is to use the "delay" option in the interface
configuration.
I want to thank Forum members dchard (in topic Adding support for
MikroTik hAP ac3 LTE6 kit (D53GR_5HacD2HnD)) [1]
and mrhaav (in topic OpenWrt X86_64 + Mikrotik R11e-LTE6) [2]
for sharing their experiments and works.
Another information page was found at eko.one.pl [3].
[1]: https://forum.openwrt.org/t/137555
[2]: https://forum.openwrt.org/t/151743
[3]: https://eko.one.pl/?p=modem-r11elte
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit dbd6ebd6d8)
The MikroTik R11e-LTE6 modem goes into flight mode (CFUN=4) at startup
and the radio is off (*RADIOPOWER: 0):
AT+RESET
OK
OK
*SIMDETEC:2,NOS
*SIMDETEC:1,SIM
*ICCID: 8936500119010596302
*EUICC: 1
+MSTK: 11, D025....74F3
*ADMINDATA: 0, 2, 0
+CPIN: READY
*EUICC: 1
*ECCLIST: 5, 0, 112, 0, 000, 0, 08, 0, 118, 0, 911
+CREG: 0
$CREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
+CGREG: 0
+CEREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
*RADIOPOWER: 0
+MMSG: 0, 0
+MMSG: 0, 0
+MMSG: 1, 0
+MPBK: 1
While the chat script is able to establish the PPP connection,
it's closed instantly by the modem: LCP terminated by peer.
local2.info chat[7000]: send (ATD*99***1#^M)
local2.info chat[7000]: expect (CONNECT)
local2.info chat[7000]: ^M
local2.info chat[7000]: ATD*99***1#^M^M
local2.info chat[7000]: CONNECT
local2.info chat[7000]: -- got it
local2.info chat[7000]: send ( ^M)
daemon.info pppd[6997]: Serial connection established.
kern.info kernel: [ 453.659146] 3g-mikrotik: renamed from ppp0
daemon.info pppd[6997]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[6997]: Using interface 3g-mikrotik
daemon.notice pppd[6997]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.info pppd[6997]: LCP terminated by peer
daemon.notice pppd[6997]: Connection terminated.
daemon.notice pppd[6997]: Modem hangup
daemon.info pppd[6997]: Exit.
daemon.notice netifd: Interface 'mikrotik' is now down
Sending "AT+CFUN=1" to modem deactivates the flight mode and
solves the issue:
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (7051): sending -> AT+CFUN=1
daemon.notice pppd[7137]: pppd 2.4.9 started by root, uid 0
local2.info chat[7140]: abort on (BUSY)
local2.info chat[7140]: abort on (NO CARRIER)
local2.info chat[7140]: abort on (ERROR)
local2.info chat[7140]: report (CONNECT)
local2.info chat[7140]: timeout set to 10 seconds
local2.info chat[7140]: send (AT&F^M)
local2.info chat[7140]: expect (OK)
local2.info chat[7140]: ^M
local2.info chat[7140]: +CESQ: 99,99,255,255,255,255^M
local2.info chat[7140]: ^M
local2.info chat[7140]: *CESQ: 99,99,255,255,255,255,0^M
local2.info chat[7140]: AT&F^MAT&F^M^M
local2.info chat[7140]: OK
local2.info chat[7140]: -- got it
...
local2.info chat[7140]: send (ATD*99***1#^M)
local2.info chat[7140]: expect (CONNECT)
local2.info chat[7140]: ^M
local2.info chat[7140]: ATD*99***1#^M^M
local2.info chat[7140]: CONNECT
local2.info chat[7140]: -- got it
local2.info chat[7140]: send ( ^M)
daemon.info pppd[7137]: Serial connection established.
kern.info kernel: [ 463.094254] 3g-mikrotik: renamed from ppp0
daemon.info pppd[7137]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[7137]: Using interface 3g-mikrotik
daemon.notice pppd[7137]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.warn pppd[7137]: Could not determine remote IP address: defaulting to 10.64.64.64
daemon.notice pppd[7137]: local IP address 100.112.63.62
daemon.notice pppd[7137]: remote IP address 10.64.64.64
daemon.notice pppd[7137]: primary DNS address 185.29.83.64
daemon.notice pppd[7137]: secondary DNS address 185.62.131.64
daemon.notice netifd: Network device '3g-mikrotik' link is up
daemon.notice netifd: Interface 'mikrotik' is now up
To send this AT command to the modem the "runcommand.gcom" script
dependency is moved from comgt-ncm to comgt.
As the comgt-ncm package depends on comgt already, this change
is a NOOP from that point of view.
But from the modem's point it is a low hanging fruit as the modem
is usable with installing comgt and kmod-usb-ncm packages.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit 91eca7b04f)
This patch solves the problem of receiving "error" responses when
initially calling gcom. This avoids unnecessary NO_DEVICE failures.
A retry loop retries the call after an "error" response within the
specified delay. A successful response will continue with the connection
immediately without waiting for max specified delay, bringing the
interface up sooner.
Signed-off-by: Mike Wilson <mikewse@hotmail.com>
(cherry picked from commit 8f27093ce7)
The modem is based on Marvell PXA1826 and uses ACM+RNDIS interface to
establish connection with custom commands specific to ZTE modems.
Two variants of modems were discovered, some identifying themselves
as "ZTE", and others as plain "Marvell", the chipset manufacturer.
The modem itself runs a fork of OpenWrt inside, which root shell can be
accessed via ADB interface.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit e02fb42c53)
Some modems expose ttyACM as their control ports, which have the
"device" symlink pointing one level down in sysfs tree. Try to find
network interfaces for them as well, this is commonly used for modems
exposing ACM + RNDIS or ACM + ECM interface combinations.
Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit ed7957810c)
Some modems expose multiple network interfaces on the same USB device,
causing the connection setup script to fail, because glob matching in
the detection phase causes 'ls' to output more than one interface name
plus their base directories in sysfs. Avoid that by listing the
directories explicitly and then selecting first available interface.
This is the case for some variants of ZTE MF286R built-in modem, which
exposes both RNDIS and CDC-ECM network interfaces, causing the
connection setup to fail.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit b2940bb8b2)
Add ifname property to UCI, which can be used to override the
autodetected interface name in case the detection fails due to having
none or more than one interface exposed by the modem, which is not
explicitly linked to TTY port. This is needed on certain variants of ZTE
MF286R built-in modem, which exposes both RNDIS and CDC-ECM interfaces
on the modem, on which the automatic detection may select the wrong
network interface.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit a67629bbe2)
This script was expecting only add/remove events which has not been the
case since Kernel 4.12 (which added bind/unbind). Bind events were getting
treated as remove events which would cause hotplugged 3g modems to not
work.
More info:
https://lkml.org/lkml/2018/12/23/128https://github.com/systemd/systemd/issues/8221
Signed-off-by: Arjun AK <arjunak234@gmail.com>
New script for comgt. Should help to fetch balance or any additional information with USSD.
This script uses the standard AT command which should be supported by all modems.
Run-tested on: Mikrotik wAP LTE KIT
Signed-off-by: Kirill Lukonin <klukonin@gmail.com>
[fixed from/sob]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
After a hardware reconnect, the control device might be unavailable and
attempting to interact with it will lead to hanging gcom calls, leaving
the protocol setup in an unrecoverable state.
Change the protocol handler to bail out early and notify netifd if the
control device is not defined or if the underlying device node does not
exist.
Also ensure that the "disconnect", "connect" and "setmode" commands are
actually defined before trying to invoke them.
Finally attempt to re-query the device manufacturer if it is unset in
the interface state in order to prevent UNUPPORTED_MODEM errors after
a modem hardware reconnect.
Signed-off-by: Rozhuk Ivan <rozhuk.im@gmail.com>
[reword subject and commit message]
Ref: https://github.com/openwrt/openwrt/pull/2352
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In the commit 623716dd43 ("comgt-ncm: Fix NCM protocol")
the dependencies to vendor NCM drivers were removed, because:
> comgt-ncm should not depend on the USB-serial-related kernel modules,
> as the cdc-wdm control device works without them. There is also no need
> to depend on kmod-huawei-cdc-ncm, since other manufacturers (like
> Ericsson and Samsung) which use other kernel modules should also be
> supported.
From a user-perspective this does not make sense, as installing comgt-ncm
(or luci-proto-ncm) should install all needed dependencies for using such
a device.
Furthermore depending on kmod-huawei-cdc-ncm does not mean that Ericsson
and Samsung devices can't be supported. By the way it seems that Ericsson
and Samsung devices never used NCM, but act as serial modems.
Thus this commit adds the dependencies again.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[fixed title capitalization, formatted commit message,
renamed Sony-Ericsson to Ericsson]
Signed-off-by: David Bauer <mail@david-bauer.net>
All protos for wwan (ncm,qmi,mbim) do have a delay option.
To standardize that add also the missing delay option to the 3g proto.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Fix an issue where subinterfaces were not added to the same
firewall zone as their parent.
Fixes: FS#2122
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Some combination of modem/wireless operator requires more time to
execute the commands.
Tested on DWR-512 embedded wwan modem and italian operator iliad (new
virtual operator).
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Fix multiple syntax errors in shelscripts (of packages only)
These errors were causing many conditions to not working properly
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[increase PKG_RELEASE, drop command substitution from directip.sh]
Signed-off-by: Mathias Kresin <dev@kresin.em>
This PR allow the 3G modem embedded in the DWR-512 to be managed
by the wwan-ncm scripts. The modem will use the usb-option and
usb-cdc-ether drivers.
The DWR-512 DT is updated accordingly.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
This reverts the following commits:
fbe522d120278ad007ee863888e44f96daf6352fcfd83555fc
This seems to trigger some mconf bugs when built with all feeds
packages, so I will try to find a less intrusive solution before the
release.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It's useful when using multiple usb devices that should be bound to
certain usb ports. Symlinks are created by hotplug handlers.
Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail.com>
Add support for specifying a call profile index instead of APN. A
specific index different from 1 must be used for some service
provider and modem combinations.
In addition, change the manufacturer detection to use the standard
AT+CGMI command, which produces more predictable output than ATI,
remove the redundant ipv6 option, since it is less ambiguous to
directly specify the PDP context type with mobile connections, and
fix missing device during teardown when using ncm through the wwan
proto.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
moving comgt and its modules to WWAN submenu to join uqmi as both are tools for WWAN modems.
I replaced the link with comgt's ubuntu manpage because the old link isn't working anymore.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
For Huawei devices like E3372 proper command for set lte mode is:
AT^SYSCFGEX="03",3fffffff,2,4,7fffffffffffffff,,
Eval is required for proper quotation.
Without this fix:
Fri Nov 4 19:07:49 2016 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 4 19:07:52 2016 daemon.notice netifd: wan (2060): sending -> AT
Fri Nov 4 19:07:52 2016 daemon.notice netifd: wan (2060): sending -> ATZ
Fri Nov 4 19:07:53 2016 daemon.notice netifd: wan (2060): sending -> ATQ0
Fri Nov 4 19:07:53 2016 daemon.notice netifd: wan (2060): sending -> ATV1
Fri Nov 4 19:07:54 2016 daemon.notice netifd: wan (2060): sending -> ATE1
Fri Nov 4 19:07:55 2016 daemon.notice netifd: wan (2060): sending -> ATS0=0
Fri Nov 4 19:07:55 2016 daemon.notice netifd: wan (2060): sending -> AT+CGDCONT=1,"IP","internet"
Fri Nov 4 19:07:57 2016 daemon.notice netifd: wan (2060): sending -> AT^SYSCFGEX=\"03\",3fffffff,2,4,7fffffffffffffff,,
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2060): Error running AT-command
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2060): Failed to set operating mode
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2092): Stopping network
...
With this fix:
Fri Nov 4 19:10:59 2016 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 4 19:11:01 2016 daemon.notice netifd: wan (2539): sending -> AT
Fri Nov 4 19:11:01 2016 daemon.notice netifd: wan (2539): sending -> ATZ
Fri Nov 4 19:11:02 2016 daemon.notice netifd: wan (2539): sending -> ATQ0
Fri Nov 4 19:11:03 2016 daemon.notice netifd: wan (2539): sending -> ATV1
Fri Nov 4 19:11:03 2016 daemon.notice netifd: wan (2539): sending -> ATE1
Fri Nov 4 19:11:04 2016 daemon.notice netifd: wan (2539): sending -> ATS0=0
Fri Nov 4 19:11:05 2016 daemon.notice netifd: wan (2539): sending -> AT+CGDCONT=1,"IP","internet"
Fri Nov 4 19:11:06 2016 daemon.notice netifd: wan (2539): sending -> AT^SYSCFGEX="03",3fffffff,2,4,7fffffffffffffff,,
Fri Nov 4 19:11:07 2016 daemon.notice netifd: wan (2539): sending -> AT^NDISDUP=1,1,"internet"
Fri Nov 4 19:11:08 2016 daemon.notice netifd: wan (2539): Connected, starting DHCP on wwan0
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan' is now up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Network device 'wwan0' link is up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Network alias 'wwan0' link is up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' is enabled
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' has link connectivity
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' is setting up now
...
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
By setting the option pdptype to IP, IPV6 or IPV4V6 the user can
choose the context type between IPv4, IPv6 and dual stack,
respectively. The default setting is dual stack, except if option
ipv6=0 is specified, in which case IPv4 context is the default.
This allows for an out-of-the-box IPv6 support with modems
utilizing NCM-like protocols.
While we are at it, also add commands for Sierra DirectIP modems
(currently untested), which will allow us to drop the separate
comgt-directip package (once tested and verified working).
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46844
The wwan package holds the hotplug script to set mobile broadband
interfaces (un)available. Add it as a dependency to comgt-ncm,
uqmi and umbim.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44631
Interface should not be set unavailable in all error cases,
returning 1 is enough.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44630
USB modem data files should be a part of the wwan package, which
actually uses them unlike comgt.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44628
When passing struct termios to ioctl TCGETS and TCSETS should be
used instead of TCGETA and TCSETA, which are meant for the older
struct termio. Should fix https://dev.openwrt.org/ticket/19012
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44506
This patch fixes the NCM protocol by adding the missing ifname
to the netifd script and changing one unintended "send" statement to
"print" in runcommand.gcom. It also cleans up logging and makes the
manufacturer names case-insensitive. Furthermore, comgt-ncm should
not depend on the USB-serial-related kernel modules, as the cdc-wdm
control device works without them. There is also no need to depend on
kmod-huawei-cdc-ncm, since other manufacturers (like Sony-Ericsson
and Samsung) which use other kernel modules should also be supported.
I'd appreciate if someone with Samsung or Sony-Ericsson modems could
test this, I was only able to test it with Huawei E3276, E3372 and
E353.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44182
Some Huawei mobile broadband sticks utilizing the NCM protocol expose
the control channel as a cdc-wdm device node instead of a virtual TTY.
This device node does not support the terminal ioctls. This patch
adds a check whether the provided device is a TTY or not and does not
attempt to use the terminal ioctls if they are not supported.
v2: reduce diffstat by simplifying code a little
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44054
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
