This was build tested with all core packages on all targets
successfully.
This was run tested on the following systems:
* lantiq/xrx200 musl
* x86/64 musl
* x86/64 glibc
* malta/be
The size of some of the initramfs images from lantiq/xrx increased by
240 bytes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the patches with real changes from the binutils 2.40 stable branch.
I am not aware that we ran into any of these problems, but I think it is
better to take the existing stable patches.
They were exported like this:
git format-patch binutils-2_40...origin/binutils-2_40-branch
I removed the patches changing the version numbers and updating the
translations only.
I removed the following patches:
*Automatic-date-updat*
001-Re-enable-development.-Update-version-to-2.40.0.patch
004-Updated-translations-for-the-gas-and-binutils-sub-di.patch
015-Updated-Swedish-translation-for-the-binutils-sub-dir.patch
027-Updated-Swedish-translation-for-the-binutils-sub-dir.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix hwmon-gsc driver by replacing out-of-tree hwmon-gsc driver with in-tree
driver that was merged in Linux v5.8:
- remove the old out-of-tree module
- add configuration for the in-tree modules
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Several devices depend on fw_printenv during sysupgrade. Make sure
it always is present in all images, including initramfs images built
by the buildbots.
Fixes: 2449a63208 ("ramips: mt7621: Add support for ZyXEL NR7101")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
If a packet has reached its intended destination, it was bumped to the code
that accepts it, without first checking if a mesh_path needs to be created
based on the discovered source.
Fix this by moving the destination address check further down
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add both ext4 and f2fs support for overlayfs. The fstools mount_root
application will choose f2fs if the overlay volume space available
exceeds 100MB, otherwise ext4 is used.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks Newport boards supported by the octeontx target have
the following on-board devices:
- Gateworks System Controller
- GPIO buttons
- GPIO leds
- GPS PPS
- Accelerometer
- MCP251X CAN controller
Add kernel drivers for these devices in DEFAULT_PACKAGES
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Forward-port from ar71xx target the board introduced in commit
eb9e3651dd (" ar71xx: add support for the MikroTik RB911-2Hn/5Hn
boards"). Citing:
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:
https://mikrotik.com/product/RB911-2Hnhttps://mikrotik.com/product/RB911-5Hn
The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.
Specifications:
* SoC: Atheros AR9344 (600MHz)
* RAM: 64MiB
* Storage: 16 MiB SPI NOR flash
* Ethernet: 1x100M (Passive PoE in)
* Wireless: AR9344 built-in wireless MAC, single chain
802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)
Notes:
* Older versions of these boards might be equipped with a NAND
flash chip instead of the SPI NOR device. Those boards are not
supported (yet).[1]
* The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
same hardware. Support for that can be added later with little
effort probably.[2]
End of citation.
Follow intallation instruction from that commit message, using
openwrt-ath79-mikrotik-mikrotik_routerboard-911-lite-initramfs-kernel.bin
and
openwrt-ath79-mikrotik-mikrotik_routerboard-911-lite-squashfs-sysupgrade.bin
images found in ath79/mikrotik directory. Be advised that the board
accepts 10-30 V on PoE input.
Known issues
Compared to ar71xx target image, there is still small leak of current to
user LED, which makes it lit, although weaker, even if brightness is set
to 0. The cause of that is still unknown.
1. https://github.com/openwrt/openwrt/pull/3652
2. RB911-5HnD should work with this commit or with [1], depending on
what flash topology was used.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Most of boards from MikroTik with AR9344 SoC (supported and
un-supported) replicate the same schematic, so stack common device nodes
to a single dtsi.
ar9344_mikrotik_routerboard-16m-nor.dtsi:
- remove include paragraph and wmac node, make it single nor flash node
for others dts to include
ar9344_mikrotik_routerboard-lhg-5nd.dts:
- move all of the nodes to new file ar9344_mikrotik_routerboard.dtsi
and leave only power, user and lan LEDs which differ from sxt-5nd-r2
and other yet unsupported devices
ar9344_mikrotik_routerboard-sxt-5n.dtsi:
- remove, it made no sense to keep it, as only
ar9344_mikrotik_routerboard-sxt-5nd-r2.dts included this file and
added only compatible and model
ar9344_mikrotik_routerboard-sxt-5nd-r2.dts:
- include ar9344_mikrotik_routerboard.dtsi
- add nand gpio activating node, beeper, additional LEDs and flash chips
which previously have been in ar9344_mikrotik_routerboard-sxt-5n.dtsi
ar9344_mikrotik_routerboard.dtsi:
- inherited most of the content from ar9344_mikrotik_routerboard-lhg-5nd.dts
except three LEDs
- add wmac node, removed from ar9344_mikrotik_routerboard-16m-nor.dtsi
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Sourcing of image/Config.in will not happen
When a target is installed from target/linux/feeds/
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
The D-Link DWL-8610AP does not make use of the B53 switch
like most equipment. It lies dormant and the machine is using
eth0 and eth1 directly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The D-Link DWL-8610AP is a pretty straight-forward BC53016
device, D-Link has invented a firmware package format which
is a tar file, and we implement this for the factory image.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
in both the stable and the testing kernel
h2+/h3/h5 devices have a Secure ID that can be read from
`/sys/bus/nvmem/devices/sunxi-sid0/nvmem`.
Enabling CONFIG_NVMEM_SYSFS grants sysfs access from userspace.
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
It seems more hardware needs early load of firmware when initialised
to work properly (at least Intel hardware). One of previous case is CPU
microcode, which this series[1] tried to change. The second one is Intel
graphics IC, which needs firmware for controlling DMC circuit (switch
conncted display to DC6 power state). As it stands, the i915 module is
built-in and it seems the hardware can't cope with firmware loaded
later from rootfs, it needs to be supplied when the module is loaded.
Unfortunately we need bootloader to handle the load of firmware in this
case, but as previously mentioned series[1], there was an error when
initrd was hardcoded, instead of testing existence for it and then
loading. To remedy this in later the 55b808e0c4 ('x86: image: add test
module to bootloader') was commited. Which was later accidentally
dropped when grub2 image creation was moved to packages. Therefore bring
back test module, so we can test for cases of existing firmware in
grub.cfg.
1. https://patchwork.ozlabs.org/project/openwrt/cover/20181120162044.16371-1-tomek_n@o2.pl
Fixes: 5a5df62d95 ("x86/grub2: move grub2 image creation to package")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This hack was to bring all existing installations to the newest GRUB
version as fast as possible. Since 19.07.x is EoL we can assume this
task is completed. Now sysupgrade will solely be responsible for
bootloader upgrade.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell
Armada 370
Hardware:
SoC: Marvell Armada 88F6707
CPU: Cortex-A9 800 MHz, 1 core
Flash 1: SPI-NOR 1 MiB (U-Boot)
Flash 2: NAND 512 MiB (OS)
RAM: DDR3 256 MiB
Ethernet: 1x 1GbE
USB: 1x 2.0
SATA: 2x 3Gb/s
LEDs/Input: 5x / 2x (1x button, 1x slide-switch)
Fan: 1x casing
Flash instructions, from hard drive:
1. Get access to the "boot" partition at the hard drive where the stock
firmware is installed. It can be done with acp-commander or by
plugging the hard drive to a computer.
2. Backup the stock uImage:
mv /boot/uImage.buffalo /boot/uImage.buffalo.bak
3. Move and rename the Openwrt initramfs image to the boot partition:
mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo
4. Power on the Linkstation with the hardrive inside. Now Openwrt will
boot, but still not installed.
5. Connect via ssh to OpenWrt:
ssh root@192.168.1.1
6. Rename boot files inside boot partition
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak
mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak
7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"):
ubiformat /dev/mtd0 -y
ubidetach -p /dev/mtd1
ubiformat /dev/mtd1 -y
8. Flash the sysupgrade image:
sysupgrade -n openwrt-squashfs-sysupgrade.bin
9. Wait until it finish, the device will reboot with OpenWrt installed
on the NAND flash.
Restore the stock firmware:
1. Take the hard drive used for the installation and restore boot backup
files to their original names:
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo
mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo
2. Boot from the hard drive and perform a stock firmware update using
the Buffalo utility. The NAND will be restored to the original
state.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The USB port on the MR8300 randomly fails to feed bus-powered devices.
This is caused by a misconfigured pinmux. The GPIO68 should be used to
enable the USB power (active low), but it's inside the NAND pinmux.
This GPIO pin was found in the original firmware at a startup script in
both MR8300 and EA8300. Therefore apply the fix for both boards.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
MT7621 uses a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Netgear R6220, WAC104 and WNDR3700 v5.
According to bootlog, MT7612E (5GHz) is connected to pcie0, and
MT7603E (2GHz) is connected to pcie2:
[2.758986] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
[2.772862] mt7621-pci 1e140000.pcie: PCIE0 enabled
[2.782579] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[3.009151] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[3.125715] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[felix.bau@gmx.de: adjust commit message for Netgear devices]
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
The hash currently matches neither the SHA256 of the Github download
nor the hash of the archive generated by the OpenWrt build system.
(and yes, they differ...)
Set hash of Github-generated tarball.
Fixes: 30f2d516ba ("tools/squashfs4: add new tool for squashfs4 images")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Assign fan with 4 active cooling levels to be used for the main CPU as
well as external SerDes units.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Several fixes for the Puzzle WT61P803 hwmon driver were needed to make
it behave well as thermal cooling device:
- wire-up cooling device with OF node in device tree
- properly parse cooling-levels (u32 with range check vs. u8)
- actually use cooling-levels
- keep current state and only write to uC if state has changed
(avoids flooding the uC with commands which will result in uC crashing)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch adds supports for GL-X1200.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB
- RAM: 128 MiB DDR2
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
- SIM: 2x SIM card slots
- MicroSD: 1x microSD slot
- Antenna: 2x external 5dBi antennas
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 16x LEDs (3x GPIO controllable)
- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
- OEM U-Boot supplies HTTP/GUI access
Implementation Notes
====================
Both the NOR and NAND variants boot off a NOR-based kernel,
consistent with the OEM's firmware.
The mode LEDs are
* Boot, Running system
* Failsafe 2G
* Upgrade 5G
Installation
============
Using sysupgrade
----------------
sysupgrade may be used to install a NAND image on a device running
a NAND image or a NOR image on a device running a NOR image. It is
recommended to *not* preserve config when upgrading from OEM firmware
or previous versions of OpenWrt. No supported sysupgrade path should
require "force". Transitioning from NOR to NAND can be accomplished
Using U-Boot
------------
The OEM U-Boot can be put into a graphical, firmware-upload mode by
holding down the button on the side of the router while applying power
and for a bit more than five seconds following with the current OEM
U-Boot. The power LED will come on, then the 5G LED will flash five
times, about once a second. When the 5G LED stops flashing and the
2G LED lights solid, the router's U-Boot will provide an upload page
at http://192.168.1.1/ Either a browser may be used to upload an image,
or a utility such as curl may be used:
curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
http://192.168.1.1/index.html
or
curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
http://192.168.1.1/index.html
Note that NOR vs. NAND is based on the file name extension.
Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
The utils subtarget was used for uClibc and eglibc
which are both obsolete and replaced in Openwrt by mainline
musl and glibc, which do not have a utils Makefile target.
Ref: 5d19a38d8 ("toolchain: sync eglibc headers/build split with uclibc changes")
Fixes: 63fb17520 ("toolchain: remove uClibc-ng")
Suggested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Reorganize dependencies between toolchain targets to save a line.
This also puts them in a linear order which is easier to read.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Use the gcc/final/install target stampfile as the prerequisite
for the toolchain/compile target stampfile.
The previous filename was also incorrect,
the stampfile name format was changed (see reference)
but was never updated here.
The issue was never noticed
because the usage of timestamp.pl was broken
(fixed in previous commit)
causing the extra prereq files passed to 'call stampfile'
to never get checked at all.
Fixes: 5149ed151 ("gcc: split up the build process into three distinct stages")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Release notes:
- Feature: link down event statistics (no option)
- Feature: JSON output for coalesce (-c)
- Feature: new link modes (no option)
- Feature: JSON output for ring (-g)
- Feature: netlink handler for RSS get (-x)
- Fix: fix boolean value output in JSON output
- Fix: fix build errors and warnings
Remove upstreamed patches:
- 100-uapi-Bring-in-if-h.patch
- 101-netlink-Fix-maybe-uninitialized-meters-variable.patch
- 102-raw-marvell-c-Fix-build-with-musl-libc.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
In DHCPv6-PD enabled environments, addresses are assigned to interfaces.
These new functions retrieve the IPv6 assigned prefix(es).
Signed-off-by: Mark Baker <mark@vpost.net>
The CONFIG_PPC_QUEUED_SPINLOCKS configuration option is not defined for
kernel 5.15, it is defined for kernel 5.10.
This fixes the compilation of mpc85xx/p2020 with kernel 5.15.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
