THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 67a3cdcbb0)
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit bdc2b58c4b)
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit a08b0d0c31)
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 978543a246)
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit ead26e9db6)
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit f928c338ad)
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for Cisco Meraki MR33
hardware highlights:
SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
1 x Orange LED Fault Indicator (shared with LP5562)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
AT24C64 8KiB EEPROM
Kensington Lock
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
1x4 0.1" header with half-height/low profile pins.
The pinout is: VCC (little white arrow), RX, TX, GND.
Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>
Add images to do an installation via bootloader:
0. open up the MR33 and connect the serial console.
1. start the 2nd stage bootloader transfer from client pc:
# ubootwrite.py --write=mr33-uboot.bin
(The ubootwrite tool will interrupt the boot-process and hence
it needs to listen for cues. If the connection is bad (due to
the low-profile pins), the tool can fail multiple times and in
weird ways. If you are not sure, just use a terminal program
and see what the device is doing there.
2. power on the MR33 (with ethernet + serial cables attached)
Warning: Make sure you do this in a private LAN that has
no connection to the internet.
- let it upload the u-boot this can take 250-300 seconds -
3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
(the u-boot is listening on 192.168.1.1)
# tftp 192.168.1.1
binary
put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin
4. wait for it to reboot
5. connect to your MR33 via ssh on 192.168.1.1
For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)
Thanks to Jerome C. for sending an MR33 to Chris.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
