The former used compatibles aren't defined anywhere and aren't used by
the devicetree source files including them.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move to i2c pins pinmux node to the pinctrl node.
Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")
Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Ralink USB PHY driver merged into mainline has a slightly different
device tree binding than the patch that was used with linux 4.9.
The new driver requires a `ralink,sysctl` node pointing to the `syscon`
node.
This patch also sets `#phy-cells` to 0, as recommended by the mainline
documentation [1].
[1] Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
Revert the changes I applied to aa5014dd1a ("ramips: mt7620n: enable
port 4 as EPHY by default").
The driver expects a node mdio-bus to be present, regardless of the
actual node status. If the node is missing the driver fails to load with
mtk_soc_eth 10100000.ethernet: no mdio-bus child node found
Disable port4 by default again. If the port is enabled but not present, a
"invalid port id 4" warning is shown during boot.
Fixes: FS#1428
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the datasheet the mt7620n have a fixed switch configuration
with 5 ephy (10/100) port. No RGMII configuration is possible.
Drop the mdio node as well. Without RGMII, the mdio node doesn't make any
sense
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[drop mdio node, enable port4 by default]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add pinmuxes defined by some board which are including the dtsi files
to the dtsi files itself. Allows to reduce duplication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit makes the following modifications to ramips dts files:
1. Add clkctrl node to all dtsi files (although not used for now)
2. Add clocks and clock-names properties to some nodes (usbphy, pci)
3. Add usbphy node for rt3050 (although not used for now)
4. Add clock-frequency to uart nodes in mt7621.dtsi and mt7628an.dtsi
These modifications, although not fully used at the moment, will make
it easier for FreeBSD to adopt and use LEDE ramips dts files with
minimal changes for easier maintenance.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
Add node aliases to dtsi files.
Reword dts files so they're more in-line with upstream.
Fix some more warnings and errors reported by dtc
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
This patch introduces serial0 aliases in the ramips DTS files, which can
then be used to denote the active console instead of relying on bootargs.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
The following patch fixes:
* wrong indentations
* doubled gpio-keys-polled nodes (DIR-300-B7, DIR-320-B1, DIR-610-A1)
* duplicate spacings
* empty lines at end of files and after last child nodes
* trailing and leading whitespace
* unnecessary and commented-out code
* missing empty lines between nodes and between properties and nodes
* unnecessary empty lines between nodes properties [1]
in .dts{,i} files, for ramips target.
[1] Some of empty lines in SOCs dtsi files were left untouched, because they seem to be there for a reason (readability?).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46613
