This includes:
1. BCM5301X changes from 5.14 and queued 5.15 stuff
2. NSP changes from 5.11 - 5.15 for kernel 5.10
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes partitioning on Linksys EA9500. With this change only the
currently used firmware MTD partition gets parsed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1. Add leds and configs
2. Add network configs
3. Add script to clear partial boot flag
4. Hack to use port 5 as cpu port as port 8 connected to eth2
wont pass any frames
5. Enable EA9500 image generation
Hardware Info:
- Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
- Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125
- DDR3 RAM - 256 MB
- Flash - 128 MB (Toshiba TC58BVG0S3HTA00)
- 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4)
- 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch
- Ports - 8 Ports, 1 WAN Ports
- Antennas - 8 Antennas
- Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1
Flashing Instructions:
1. Connect a USB-TTL table to J6 on the router as well as a
ethernet cable to a lan port and your PC.
2. Power-on the router.
3. Use putty or a serial port program to view the terminal.
Hit Ctrl+C and interrupt the CFE terminal terminal.
4. Setup a TFTP server on your local machine at setup you
local IP to 192.168.1.2
5. Start the TFTP Server
6. Run following commands at the CFE terminal
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2
nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit
7. Reboot router to be presented by OpenWrt
Note: Only installation method via serial cable is supported at the moment.
The trx firmware has to be flashed to both the partitions using following
commands from CFE prompt. This will cover US and Non-US variants.
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[remove accidental whitespace edit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
NVRAM access may be needed early in boot process. Reading it using mtd
happens quite late in the init process. Add NVRAM initialization to the
NVMEM driver which comes up early and depends on IO mapping only.
This is required by Linksys devices which use NVRAM content for proper
partitioning (detecting current firmware partition).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It supports NVRAM access described using DT binding. Right now NVRAM
data is exposed using /sys/bus/nvmem/ only.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is required for devices that use NVRAM data for detecting currently
used firmware partition (e.g. Linksys devices).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
These patches have been already accepted.
302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch had to
be updated.
[rmilecki: use actual upstream accepted patches
replace v5.10 with v5.11 to match actual upstream kernel
recover dropped part of the pinctrl compatible patch
update filenames
refresh patches]
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Manually rebased patches:
bcm27xx:
patches-5.4/950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch
bcm53xx:
patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
layerscape:
patches-5.4/802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
patches-5.4/808-i2c-0002-MLK-10893-i2c-imx-add-irqf_no_suspend.patch
patches-5.4/820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch
Removed since could be reverse-applied by quilt:
mediatek:
patches-5.4/0700-arm-dts-mt7623-add-missing-pause-for-switchport.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86_64
Run-tested: ipq806x/R7800, x86_64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64]
Rebase of 802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Seemingly unneeded based on new upstream code so manually deleted:
layerscape:
820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack:
251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test report, minor commit message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for Cisco Meraki MR32.
The unit was donated by Chris Blake. Thank you!
WARNING:
Only the 1x1:1 abgn Air Marshal WIPS wifi is currently supported by b43:
b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
b43-phy2: Loading firmware version 784.2 (2012-08-15 21:35:19)
and only as 802.11ABG!
while WIFI1 and WIFI2 (both BCM4352) are not:
b43-phy0: Broadcom 4352 WLAN found (core revision 42)
b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1)
Hardware Highlights:
SoC: Broadcom BCM53016A1 (1 GHz, 2 cores)
RAM: 128 MiB
NAND: 128 MiB Spansion S34ML01G2 (~114 MiB useable)
ETH: 1GBit Ethernet Port - PoE
WIFI1: Broadcom BCM43520 an+ac (2x2:2 - id: 0x4352)
WIFI2: Broadcom BCM43520 bgn (2x2:2 - id: 0x4352)
WIFI3: Broadcom BCM43428 abgn (1x1:1 - id: 43428)
BLE: Broadcom BCM20732 (ttyS1)
LEDS: 1 x Programmable RGB Status LED (driven by a PWM)
1 x White LED (GPIO)
1 x Orange LED Fault Indicator (GPIO)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: AT24C64 8KiB EEPROM (i2c - stores Ethernet MAC + Serial#!)
ina219 hardware monitor (i2c)
Kensington Lock
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC, RX, TX, GND. (Use a multimeter)
Flashing needs a serial adaptor (due to the lack of a working dropbear on
the original firmware).
This flashing procedure for the MR32 was tested with firmware:
"r23-149867:150252-aacharya".
0. Create a seperate Ethernet LAN which does not have access to the internet.
Ideally use 192.168.1.2 for your PC. Make sure to reserve 192.168.1.1 it
will be used later on by the OpenWrt firmware. The original Meraki firmware
will likely try to setup the network via DHCP Discovery, so make sure your
PC is running a DHCP-Server (i.e.: dnsmasq)
'# dnsmasq -i eth# -F 192.168.1.5,192.168.1.50
Furthermore, the PC needs a supported ssh/http/ftp server in order to
retrieve the initramfs + dtb file
1. Disassemble the MR32 device by removing all screws (4 screws are located
under the 4 rubber feets!) and prying open the plastic covers without
breaking the plastic retention clips. Once inside, remove all the screws
on the outer metal shielding to get to the PCB. It's not necessary to
remove the antennas!
2. Connect the serial cable to the serial header.
3. Partially reassemble the outer metal shielding to ensure that the SoC
has a proper heat sink.
4. Connect the Ethernet patch cable to the device and the power cable.
5. Wait for the device to boot and enter the root shell.
(rooting is not discussed in detail here please refer to
Chris Blake - "pwning the meraki mr18" blog post:
<https://servernetworktech.com/2016/02/pwning-the-meraki-mr18/>
(The same method works with the MR32's r23-149867:150252-aacharya)
Wait for the MR32 to enter the "<Meraki>" prompt and enter:
<Meraki> odm serial_num read
(Verify that it matches what's on the S/N Sticker on the back!)
<Meraki> odm serial_num write Q2XX-XXXX-XXXV
<Meraki> odm serial_num read
(Verify that the S/N has changed - and the LED start to flash)
now to flash the firmware:
<Meraki> odm firmware part.safe "http://192.168.1.2/mr32-initramfs.bin"
Once OpenWrt booted use sysupgrade to permanently install
OpenWrt. To do this: Download the latest sysupgrade.bin file
for the MR32 to the device and use sysupgrade *sysupgrade.bin
to install it.
WARNING: DO NOT DELETE the "storage" ubi volume!
To flash later MR32 Firmwares like r25-201804051805-G885d6d78-dhow-rel
requires in-circut-i2c tools to access the I2C EEPROM AT24C64 next to
the SoC. The idea is pretty much the same as from Step 5 from above:
Change the serial number to Q2XXXXXXXXXV (should be around 0x7c), then
attach a serial cable, ethernet (but make sure the device can't reach
the internet!) hit "s" (the small s!) during boot to enter the root-shell
and add the following commands to the /storage/config there:
serial_allow_odm true
serial_access_enabled true
serial_access_check false
valid_config true
and then hit exit to let it finish booting.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
These have made their way into -next. This patch
also includes the portion of the bcm53xx kernel
patch refreshes as the hunks in
302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch
moved slightly due to the added nodes.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Meraki MR32 (BCM53016A1) uses the pwm to drive the
tricolor LED. The driver has been available in upstream
for a long time. Only the Device-Tree definition was
missing, but it has been queued recently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This PR is a blend of several kernel bumps authored by ldir taken from his
staging tree w/ some further adjustments made by me and update_kernel.sh
Summary:
Deleted upstreamed patches:
generic:
742-v5.5-net-sfp-add-support-for-module-quirks.patch
743-v5.5-net-sfp-add-some-quirks-for-GPON-modules.patch
bcm63xx:
022-v5.8-mtd-rawnand-brcmnand-correctly-verify-erased-pages.patch
024-v5.8-mtd-rawnand-brcmnand-fix-CS0-layout.patch
mediatek:
0402-net-ethernet-mtk_eth_soc-Always-call-mtk_gmac0_rgmii.patch
Deleted patches applied differently upstream:
generic:
641-sch_cake-fix-IP-protocol-handling-in-the-presence-of.patch
Manually merged patches:
generic:
395-v5.8-net-sch_cake-Take-advantage-of-skb-hash-where-appropriate.patch
bcm27xx:
950-0132-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch
layerscape:
701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ath79/generic, bcm27xx/bcm2708, bcm27xx/bcm2711,
imx6, mvebu/cortexa9, sunxi/a53
Run-tested: Netgear R7800 (ipq806x)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-By: Lucian Cristian <Lucian.cristian@gmail.com> [mvebu]
Tested-By: Curtis Deptuck <curtdept@me.com> [x86/64]
[do not remove 395-v5.8-net-sch_cake-Take-advantage-... patch,
adjust and refresh patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
