Specification:
SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
- 2.4GHz: MT7628AN
- 5GHz: MT7612EN
LAN: 1x 10/100 Mbps
Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.
The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Most of the kernel version switches below 4.14 were removed in commit
97940f8766 ("kernel: remove obsolete kernel version switches"),
but some of them still remained. Remove them now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Using the led_ prefix for the node label is now common in ath79,
so also apply it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Using the LED of network interfaces for status (boot/failsafe/...)
indication is somewhat misleading, as the blinking might be
mistaken for network activity. This uses rssi LEDs instead, which
do not blink normally and thus are less ambiguous.
The rssihigh LED has also been used consistently for the TP-Link CPE
devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"#mediatek,portmap" is not a valid property name.
If mediatek,portmap equals 0x0, then the esw driver ditches it and uses
the default value, 0x3f.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
mt76x8 uses esw_rt3050 driver, which does not accept mediatek,portmap with
string values. Convert the strings to integers to make it work.
According to its switch setup, WRTnode 2P/2R have a WAN port at port 0,
so the correct value should be 0x3e.
tplink_8m.dtsi uses "llllw", but it does not match switch setups of any
device using the DTSI. Remove it from the DTSI and add correct value to DTS
for each device.
These devices have a WAN port at port 0. Set the value to 0x3e.
- tplink,archer-c20-v4
- tplink,archer-c50-v3
- tplink,tl-mr3420-v5
- tplink,tl-wr840n-v4
- tplink,tl-wr841n-v13
- tplink,tl-wr842n-v5
These devices have only one ethernet port. They don't need portmap setting.
- tplink,tl-wa801nd-v5
- tplink,tl-wr802n-v4
- tplink,tl-wr902ac-v3
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
mt7620 and mt7621 use mt7530 driver, which only accepts "llllw", "wllll",
and "lwlll" values.
According to its switch setup, Mi Router 3G v2 has a WAN port at port 4,
so the correct value should be "llllw".
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
It's cleaner and faster as it does not need to do extra work.
Also removed $() to avoid executing the output. The shell can handle it.
https://github.com/koalaman/shellcheck/wiki/SC2143
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[correct || to && for one conversion]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- fix color and active mode for existing wps led
- add green wps led
- add wps button
Signed-off-by: Jan Alexander <jan@nalx.net>
[wrap line]
Signed-off-by: David Bauer <mail@david-bauer.net>
When building libcxx for x86/64, the library is installed in /usr/lib64.
As the install section tries to copy the library from /usr/lib, this
breaks build on x86/64. Override the lib dir suffix to fix this.
Fixes: 856ea2bad3 ("libcxx: Add package")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rosen Penev <rosenp@gmail.com>
6db312a dhcpv6-ia: use dhcp leasetime to set preferred/valid statefull lifetimes
2520c48 dhcpv6-ia: introduce DHCPv6 pd and ia assignments flags
b413d8a dhcpv6-ia: cleanup prefix delegation routes
b0902af dhcpv6-ia: remove passing interface as parameter to apply_lease
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Currently, it is very cumbersome for a user to connect to a WPA-Enterprise
based network securely because the RADIUS server's CA certificate must first be
extracted from the EAPOL handshake using tcpdump or other methods before it can
be pinned using the ca_cert(2) fields. To make this process easier and more
secure (combined with changes in openwrt/openwrt#2654), this commit adds
support for validating against the built-in CA bundle when the ca-bundle
package is installed. Related LuCI changes in openwrt/luci#3513.
Signed-off-by: David Lam <david@thedavid.net>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put usb-phy into reset if clearing the usb-phy reset or
setting the suspend_override has failed.
Reorder (de)asserts like in arch/mips/ath79/dev-usb.c.
Add an optional reset_control "usb-phy-analog", which is needed for
ar934x SoCs like in the old mach-driver arch/mips/ath79/dev-usb.c.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
This image is only needed on one device (wAP AC); since this target is
going to be removed anyway it doesn't make sense to add an extra "low
RAM" image.
Fixes OOM issues on RouterBoard wAP AC.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
In function `main` add calls to `free` for the variable `executable`.
This is needed because the variable `executable` is allocated but
never freed. This cause a memory leak.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
Change the caldata partition DTS node label to be consistent with
the label property for some Netgear WNDR devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If a config section of a peer does not have a public key defined, the
whole interface does not start. The following log is shown
daemon.notice netifd: test (21071): Line unrecognized: `PublicKey='
daemon.notice netifd: test (21071): Configuration parsing erro
The command 'wg show' does only show the interface name.
With this change we skip the peer for this interface and emit a log
message. So the other peers get configured.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.
Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:
* two USB 2.0 ports with separate LEDs
* USB LEDs soldered to secondary pads
* WPS and RFKILL buttons soldered to secondary pads
* described as N900 device with 3x3:3 MIMO for 2.4GHz radio
* power supply requirement is DC 12V 2.5A
* vendor HW ID suffix differs in one digit
* bigger chassis
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This patch introduces support for Netgear WNDR4300v2.
Specification
=============
* Description: Netgear WNDR4300 v2
* Loader: U-boot
* SOC: Qualcomm Atheros QCA9563 (775 MHz)
* RAM: 128 MiB
* Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND
- NOR: U-boot binary: 256 KiB
- NOR: U-boot environment: 64 KiB
- NOR: ART Backup: 64 KiB
- NOR: Config: 64 KiB
- NOR: Traffic Meter: 64 KiB
- NOR: POT: 64 KiB
- NOR: Reserved: 1408 KiB
- NOR: ART: 64 KiB
- NAND: Firmware: 25600 KiB (see notes for OpenWrt)
- NAND: Language: 2048 KiB
- NAND: mtdoops Crash Dump: 128 KiB
- NAND: Reserved: 103296 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Important Notes
===============
0. NOR Flash (2 MiB) is not touched by OpenWrt installation.
1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows:
all space is split between 4 MiB kernel and 124 MiB UBI areas;
vendor partitions (language and mtdoops) are removed; kernel space
size can be further expanded if needed; maximum image size is set
to 25600k for compatibility reasons and can also be increased.
2. CPU clock is 775 MHz, not 750 MHz.
3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI
device ID 0xabcd. For ath9k driver to load successfully, this is
overriden in DTS with correct value for this chip, 0x0033.
4. RFKILL button is wired to AR9580 pin 9 which is normally disabled
by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore
'qca,gpio-mask=<0xf6ff>' hack must be used for button to work
properly.
5. USB port is always on, no GPIO for 5V power control has been
identified.
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This patch adds 'qca,gpio-mask=<u32>' device tree property to ath9k node.
This optional setting is a hack and should only be used in very special
(and rare) cases when a button or LED is wired to a GPIO pin normally
masked out (due to being one-way etc). Netgear WNDR4300 v2 is one such
example - it uses GPI9 for RFKILL.
See ath9k/reg.h *_GPIO_MASK constants.
Use with caution and expect to see stream of kernel warnings if wrong
mask value is provided.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
If zram-backed swap is added after an existing swap, it gets a lower
priority. Assiming that usually all other swaps are slower, there should
be a way to assign a higher priority to zram swap.
Signed-off-by: Maxim Storchak <m.storchak@gmail.com>
This commit adds support for the D-Link DIR-505, previously supported in
ar71xx.
Hardware
--------
SoC: Atheros AR9330
FLASH: 8M SPI-NOR
RAM: 64M
WIFI: 1T1R 1SS Atheros AR9330
LED: Power green, Status red
BTN: WPS, Reset
Installation
------------
Currently, installation is only possible by sysupgrading from an earlier
OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the
original bootloader from D-Link on my device anymore, so i cannot test
the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
The depends are totally wrong. libunwind does not work with powerpc and
i386 as it needs glibc.
Instead of duplicating the platforms, just change the dependency.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
With this change it is now possible to switch off single instances of
the uhttpd config. Until now it was only possible to switch all
instances of uhttpd on or off.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Rekey GTK on STA disassociate
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Allows dtim_period to be configurable, the default is from hostapd.
Adds additional regulatory tunables for power constraint and spectrum
managment.
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
The present U-Boot for GL-AR750S has a limit of 2 MB for kernel size.
While sysupgrade can manage kernels up to the present limit of 4 MB,
directly flashing a factory.img with a kernel size greater than 2 MB
through U-Boot will result in an unbootable device.
This commit uses the newly-introduced check-kernel-size build
operation to prevent the output of factory.img when the kernel
exceeds 2 MB in size, yet permits output of sysupgrade.img
as long as the kernel is within KERNEL_SIZE := 4096k
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Certain boards have limitations on U-Boot that prevent flashing
of images where the kernel size exceeds a threshold, yet
sysupgrade can sucessfully manage larger kernels. The current
check-size will remove the target artifact if its total size
exceeds the threshold. If applied after append-kernel,
it will remove the kernel, but the remaining image-assembly
steps will continue, resulting in an image without a kernel
that is likely unbootable.
By defining check-kernel-size, it is now possible to prevent release
of such unbootable images through a construct similar to:
IMAGE/factory.img := append-kernel | pad-to $$$$(GL_UBOOT_UBI_OFFSET) | \
append-ubi | check-kernel-size $$$$(GL_UBOOT_UBI_OFFSET)
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Failsafe code of dropbear should be in the dropbear package not the
base-files package.
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
NAS devices certainly need to have hdparm to configure
things like spin-down time or their disks will be
constantly spinning. Just catenate CONFIG_HDPARM=y
on these configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The memory hacks got removed from ath10k with 1e27bef ("mac80211: remove
ath10k_pci memory hacks"). As this device has low amount of RAM, switch
to ath-10k-ct small buffers variant, to avoid the OOM Reaper.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The 'DEFAULT:=m if ALL' line prevents the phase1 buildbots from building
the package, and users from downloading it, since they use 'ALL_KMODS=y'
but 'ALL' is not set.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This reorganizes 02_network board.d files based on what's done for
ath79 and ramips: Instead of putting all settings into a single big
case, the interface/dsl/MAC address setup is put into separate
functions with a specific switch case for each of them. This makes
grouping of devices much easier and should be easier to read, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DSL setup consists of the same commands for all subtargets, so move it
into a helper function.
While at it, remove shebang from library file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
