OpenWrt's special gpio-button-hotplug driver is still using
exclusively the legacy GPIO Subsystem gpio_ API.
While it still does work fine for most devices, upstream
linux is starting to convert platform support like that of
the APU2/3/4 to the new GPIOD LOOKUP tables that are not
supported by it.
Hence, this patch replaces the gpio_ calls present in
gpio-button-hotplug with gpiod_ equivalent wherever
it's possible. This allows the driver to use the
gpiod lookup tables and still have a fallback for
legacy platform data code that just sets button->gpio
set to the real button/switch GPIO.
As a bonus: the active_low logic is now being handled
by the linux's gpio subsystem too. Another issue that
was address is the of_handle leak in the dt parser
error path.
Tested with legacy platform data: x86_64: APU2, MX-100
Tested on OF: ATH79; MR18, APM821xx: Netgear WNDR4700,
RAMIPS: WL-330N3G
LANTIQ: AVM FritzBox 7360v1
Reported-by: Chris Blake <chrisrblake93@gmail.com>
Tested-by: Chris Blake <chrisrblake93@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The userspace application now uses the model=full option to match the
configuration of the kernel module. The source no longer contains SOAP
support, which was the primary reason to build only typical instead
of full before.
This makes several CLI commands, which were already supported in the
kernel module, available in the userspace application. For example, this
includes bbsg which allows to get information about VDSL2 bands.
Some previously applied build options were redundant. Disabling ADSL MIB
support is unnecessary, as it only applies to Danube. ADSL LED support
is no longer included in the source. ReTx counters are already included
with model type full.
This increases the size of the userspace application by approximately
15 kB (uncompressed). The kernel module does not change at all.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The xfrm_interface module will not be built if IPv6 is not enabled in
the kernel. Add this dependency in the kmod package to avoid people
wondering why it doesn't build when they disabled IPv6.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
When the kmod-qlcnic package is built on targets that have
CONFIG_PCI_IOV enabled, the CONFIG_QLCNIC_SRIOV symbol is exposed.
Enable this symbol in the kmod package to fix its build.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
of_platform_device_create require CONFIG_OF selected.
Add an ifdef and register to the of platform only if of is available.
Fixes: 985954ccbd ("kernel: add ath10k support for of_get_mac_address")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
ath10k doesn't currently support the standard function to get mac-address from the dts.
Add this for both ath10k and ath10k-ct
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
drv_mac80211_teardown fails silently if the device to be torn down is
not defined. This commit prints an error message.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
When wifi is turned off, drv_mac80211_teardown sometimes fails (silently)
because the device to be torn down is not defined.
This situation arises if drv_mac80211_setup was called twice when
wifi was turned on.
This commit ensures that the device to be torn down is always defined
in drv_mac80211_teardown.
Steps to reproduce:
1) Use /sbin/wifi to turn on wifi.
uci set wireless.@wifi-iface[0].disabled=0
uci set wireless.@wifi-device[0].disabled=0
uci commit
wifi
2) Use /sbin/wifi to turn off wifi.
uci set wireless.@wifi-device[0].disabled=1
uci commit
wifi
3) Observe that wifi is still up.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
If drv_mac80211_setup is called twice with the same wifi configuration,
then the second call returns early with error HOSTAPD_START_FAILED.
(wifi works nevertheless, despite the fact that setup is incomplete. But
"ubus call network.wireless status" erroneously reports that radio0 is down.)
The relevant part of drv_mac80211_setup is,
if [ "$no_reload" != "0" ]; then
add_ap=1
ubus wait_for hostapd
local hostapd_res="$(ubus call hostapd config_add "{\"iface\":\"$primary_ap\", \"config\":\"${hostapd_conf_file}\"}")"
ret="$?"
[ "$ret" != 0 -o -z "$hostapd_res" ] && {
wireless_setup_failed HOSTAPD_START_FAILED
return
}
wireless_add_process "$(jsonfilter -s "$hostapd_res" -l 1 -e @.pid)" "/usr/sbin/hostapd" 1 1
fi
This commit sets no_reload = 0 during the second call of drv_mac80211_setup.
It is perhaps worth providing a way to reproduce the situation
where drv_mac80211_setup is called twice.
When /sbin/wifi is used to turn on wifi,
uci set wireless.@wifi-iface[0].disabled=0
uci set wireless.@wifi-device[0].disabled=0
uci commit
wifi
/sbin/wifi makes the following ubus calls,
ubus call network reload
ubus call network.wireless down
ubus call network.wireless up
The first and third ubus calls both call drv_mac80211_setup,
while the second ubus call triggers wireless_device_setup_cancel.
So the call sequence becomes,
drv_mac80211_setup
wireless_device_setup_cancel
drv_mac80211_setup
In contrast, when LuCI is used to turn on wifi only a single call
is made to drv_mac80211_setup.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
CONFIG_CRYPTO_DEV_HIFN_795X depends on PCI. This driver only makes sense on
devices with pci support.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Without loading the igb at boot, the recovery wouldn't have
network available. All network drivers should be loaded before
etc/board.d/02_network is called. Note that other network drivers
already have this set, such as tg3.
Fixes: 7e0e5110bc ("kernel: add igb kernel module")
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Use of WPA3 and things like FILS is getting much more common, and platforms
that can't affort the extra kilobytes for this code are fading away.
Let's not hold back modern authentication methods any longer
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We need to skip sampling if the next sample time is after jiffies, not before.
This patch fixes an issue where in some cases only very little sampling (or none
at all) is performed, leading to really bad data rates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The removed patches were integrated upstream.
The brcmf_driver_work workqueue was removed in brcmfmac with kernel
5.10.42, the asynchronous call was covered to a synchronous call. There
is no need to wait any more.
This part was removed manually from this patch:
brcm/860-brcmfmac-register-wiphy-s-during-module_init.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add mt7915e dependency on kmod-thermal
22b690334c0f mt76: mt7915: do not fail if the cooling device could not be registered
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ath patch number is already large and adding other patch for ath11k
will add more confusion with the patch numbering.
Since the support of ath11k based device is imminent, prepare the mac80211
ath patch dir and split it in the dedicated ath5k, ath9k, ath10k and ath11k
(empty for now).
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
bddc1db76d0f mt76: mt7915: drop the use of repeater entries for station interfaces
3c90f35dddac mt76: mt7915: add thermal sensor device support
afab0e8202ff mt76: mt7915: add thermal cooling device support
41cf02184699 mt76: mt7615: add thermal sensor device support
2ac6b8762565 mt76: connac: update BA win size in Rx direction
ddb301127291 mt76: mt7921: fix reset under the deep sleep is enabled
e4cbefd1d69a mt76: mt7921: avoid unnecessary consecutive WiFi resets
393eea2034d7 mt76: mt7921: fix invalid register access in wake_work
a15d46407ffa mt76: mt7921: fix OMAC idx usage
e4d267d8e900 mt76: mt7921: enable runtime pm by default
50fd8ce2412a mt76: connac: add bss color support for sta mode
e29058c3c860 mt76: mt7921: return proper error value in mt7921_mac_init
c89c8c347b1e mt76: mt7921: do not schedule hw reset if the device is not running
9f7bb428e587 mt76: mt7921: reset wfsys during hw probe
22ea365913b5 mt76: mt7915: add .offset_tsf callback
ad91f8e8e494 mt76: mt7615: add .offset_tsf callback
6f871f35e3c1 mt76: mt7915: use mt7915_mcu_get_txpower_sku() to get per-rate txpower
597b68b7daa3 mt76: mt7615: remove useless if condition in mt7615_add_interface()
3945264468eb mt76: testmode: fix memory leak in mt76_testmode_alloc_skb
bdcc57a11606 mt76: testmode: remove unnecessary function calls in mt76_testmode_free_skb
a9763452601d mt76: testmode: remove undefined behaviour in mt76_testmode_alloc_skb
4aef2a2be464 mt76: mt7615: fix potential overflow on large shift
d9dd7635b055 mt76: mt7915: use mt7915_mcu_get_mib_info() to get survey data
d740e921758a mt76: mt7921: introduce mac tx done handling
259ddfc7cb73 mt76: mt7921: update statistic in active mode only
757b93f4b179 mt76: mt7921: remove leftover 80+80 HE capability
1fcff599b2e1 mt76: allow hw driver code to overwrite wiphy interface_modes
c55c22e39b7d mt7915: update firmware to 2020110522
10548aef1f45 mt76: mt7915: improve error recovery reliability
ed6b0c79820c mt76: mt7921: set MT76_RESET during mac reset
321443258bea mt76: move mt76_rates in mt76 module
d1652e8af9e1 Revert "mt76: connac: do not schedule wake_work if the runtime-pm is disabled"
4f4cab39ed9f mt76: mt7915: read all eeprom fields from fw in efuse mode
71450535f164 mt76: mt7921: enable hw offloading for wep keys
833d577e430c mt76: mt7921: remove mt7921_get_wtbl_info routine
67b7a22d2b99 mt76: mt7921: enable random mac address during sched_scan
cf1ff7bf4f1b mt76: mt7915: setup drr group for peers
ef2f7aa8745f mt76: mt7615: update radar parameters
b9f09f530223 mt76: mt7915: fix MT_EE_CAL_GROUP_SIZE
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some drivers advertise it, but it's not supported at the moment
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The colon does not directly follow the "VHT Capabilities" string
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
