As x86/64 and x86/generic may be using UEFI, mounting the FAT-32 /boot
is necessary in order not to loose configuration files accross
sysupgrades. Include kmod-fs-vfat by default to make sure /boot can
always be mounted.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
NR_CPUS limits the number of CPUs supported to 8. This makes total sense
on hardware-restircted platforms, but not on x86_64, where CPUs with
more than 8 cores can be easily acquired and with less physical limitaions.
see also: https://forum.openwrt.org/t/x86-64-8-cpu-limitation-on-vanilla-release/100946
Signed-off-by: Edgar Su <sjs333@outlook.com>
Similar to how this is done in the diag.sh found in the base-files
package, we should blink our status LED (if we have one) during the
upgrade process. This follows the same blink pattern as seen at
./package/base-files/files/etc/diag.sh#L36
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
eth0 -> single NIC (i211at)
eth1 -> single NIC (i211at) -> 4-port unmanaged switch (BCM53125U)
Notes
UART is exposed on J4 connector, pinout starting from pin marked 1:
1. GND, 2. NC?, 3. NC?, 4. RX, 5. TX, 6. NC?
baud: 115200, parity: none, flow control: none
The board is setup by coreboot with UEFI. To enter setup screen hold
ESC key on boot.
The 5-LED multicolor matrix is attached on first I2C device named
"Synopsys DesignWare I2C adapter" at address 0x60. Controlling values
are stored in /opt/roqos/etc/rcLED.conf of original firmware.
Remember to backup the original firmware, there are no downloadable
copies.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Compile in MPT SAS driver required to mount rootfs on some VMWare
systems (e.g. required for 1&1 IONOS).
Signed-off-by: Mark Carroll <git@markcarroll.net>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
fix the following build error when building with test kernel:
Package kmod-amd-xgbe is missing dependencies for the following libraries:
mdio_devres.ko
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This feature is already supported in kernel. Add definition
and configuration in Makefile of OpenWRT.
It is tested on board Dibbler with processor V1605B.
Dmesg is as below.
--------------------------------------------
[ 0.317122] smpboot: CPU0: AMD Ryzen Embedded V1605B with Radeon
Vega Gfx (family: 0x17, model: 0x11, stepping: 0x0)
[ 8.227270] libphy: amd-xgbe-mii: probed
[ 8.228189] amd-xgbe 0000:02:00.1 eth0: net device enabled
[ 8.228999] libphy: amd-xgbe-mii: probed
[ 8.229921] amd-xgbe 0000:02:00.2 eth1: net device enabled
.....
[ 11.760869] br-lan: port 1(eth0) entered blocking state
[ 11.761365] br-lan: port 1(eth0) entered disabled state
[ 11.762019] device eth0 entered promiscuous mode
[ 11.785285] 8021q: adding VLAN 0 to HW filter on device eth1
[ 16.881431] amd-xgbe 0000:02:00.1 eth0: Link is Up - 1Gbps/Full -
flow control off
[ 16.882108] br-lan: port 1(eth0) entered blocking state
[ 16.882583] br-lan: port 1(eth0) entered forwarding state
[ 16.883249] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
-----------------------------------------------
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
The CONFIG_USERIO option is unset in multiple target configurations. On
the sunxi target it is activated. Move the kernel configuration option
to the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds detection of the Sophos SG-105 and Sophos XG-105 models
and assignment of ethernet ports these models have to LAN/WAN.
Signed-off-by: Stan Grishin <stangri@melmac.net>
This patch really annoys me, either it needs to go upstream or be
dropped, so it's going to be dropped here.
Checking drivers/platform/x86/pcengines-apuv2.c it also appears to be
incomplete since it mentions different dmi board names depending on bios
version.
/* APU2 w/ legacy BIOS < 4.0.8 */ is 'APU2'
/* APU2 w/ legacy BIOS >= 4.0.8 */ is 'apu2'
/* APU2 w/ mainline BIOS */ is 'PC Engines apu2'
So the patch, if applicable at all, only 'works' for legacy BIOS >=
4.0.8
My APU2 on mainline BIOS reboots fine without this patch. So let's see
if anyone screams and when they do question why legacy bios. If patch
DOES need to be re-introduced then it needs to go upstream first.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Straightforward refresh of patches using update_kernel.
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Update 5.10 generic config to add missing options prompting during builds,
when setting CONFIG_ALL_KMODS. Refresh the x86 subtargets to drop symbols
added to the generic config.
Also fix a typo in 5.4/5.10 generic configs: "CONFIG_CONFIG_KVM_AMD_SEV".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The 5.10 target config defined a baseline i686 CPU aligned to the 32-bit
generic subtarget. However, the legacy subtarget arch wasn't set to the
older 586MMX, defaulting instead to the i686.
Explicitly set the subtarget arch and refresh the subtarget config, as done
already with the old geode subtarget.
Fixes: 8391781389 ("x86: support kernel 5.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add linux 5.10 as testing kernel, copy generic/subtarget configs and target
patches from 5.4.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
x86: update target patches for kernel 5.10
Refresh all patches while also dropping:
800-hwmon-w83627ehf-dont-claim-nct677x.patch
which is now upstreamed as:
3207408ab4cb ("hwmon: (w83627ehf) remove nct6775 and nct6776 support")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
x86: refresh 5.10 target config
Refresh config using "make kernel_oldconfig".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
x86: refresh and test all subtarget configs
Refresh configs using "make kernel_oldconfig CONFIG_TARGET=subtarget".
Build and run-tested using QEMU: x86/64, x86/legacy, x86/generic.
Build-tested only: x86/geode.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[squashed commits]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Amazon AWS T3 cloud instances require kernel support
for the Elastic Fabric Adapter to access storage
and for Elastic Network Adapter to use network
interfaces.
Since the Fabric Adapter is needed to access
root filesystem, enable in x86_64 kernel.
Elastic Network Adapter goes in a module,
and add this module to default list in x86_64.
The module is set to AutoLoad because AutoProbe does
not seem to load it.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
This driver adds the LED support for the PC Engines APU1.
This integrates the Linux kernel driver and includes a patch to support
newer firmware versions. Also the default LED configuration is updated
to use the correct devices.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
x86 uses append-metadata, but only for signing and not for the
metadata itself.
Since recently SUPPORTED_DEVICES was assigned with a global value
and is not empty anymore, append-metadata will now actually put
metadata into x86 images. This breaks sysupgrade on x86.
To fix it for the moment, let's just empty SUPPORTED_DEVICES for
this target again.
In the long term, one should either not add metadata to the images
if it is not desired, and/or remove the unintended fwtool check.
Fixes: f52081bcf9 ("treewide: provide global default for SUPPORTED_DEVICES")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Some x86_64 single board computer (including Atomic Pi)
has onboard emmc, but requires CONFIG_MMC_SDHCI_ACPI driver
to use or boot from it.
Here is boot message for the mmc device
[ 2.838008] mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
[ 2.857536] mmc1: SDHCI controller on ACPI [80860F14:01] using ADMA
[ 2.950019] mmc0: new HS200 MMC card at address 0001
[ 3.158271] mmcblk0: mmc0:0001 M52516 14.6 GiB
[ 3.170290] mmcblk0boot0: mmc0:0001 M52516 partition 1 4.00 MiB
[ 3.177191] mmcblk0boot1: mmc0:0001 M52516 partition 2 4.00 MiB
[ 3.183963] mmcblk0rpmb: mmc0:0001 M52516 partition 3 4.00 MiB, \
chardev (248:0)
Other lines changed in this config file are introduced by menuconfig.
Signed-off-by: Mengyang Li <mayli.he@gmail.com>
CONFIG_EFI_VARS has been disabled in
64bit x86 target in 2018 by the following commit
b0a51dab8c
the same reasons apply to Generic target, so
now it's disabled here too.
Leaving it enabled is also blocking compile as
a new symbol was added
EFI_CUSTOM_SSDT_OVERLAYS
that depends from CONFIG_EFI_VARS
and the build system stops and waits for
user input on what to do about it.
The Legacy and Geode targets never
had any EFI_xxx configs enabled so they
don't have this issue
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
The comment content can be useful for readers of both the log and code
Previously when dd command "records in/out" messages are not filtered
like now with get_image_dd, it's not clear that these messages are for
extracting boot sectors. E.g.
Before
== upgrade: Reading partition table from bootdisk...
37+26 records in
37+26 records out
== upgrade: Reading partition table from image...
After
== upgrade: Reading partition table from bootdisk...
== upgrade: Extract boot sector from the image
37+26 records in
37+26 records out
== upgrade: Reading partition table from image...
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The mount point is "/tmp/boot", the path in the boot partition is
"/boot/grub/upgraded".
Origin of this mark b9c1cf16 ("x86: add preinit hook for bootloader
upgrade")
Fixes 32f675ca ("x86: fix grub-bios-setup fail during sysupgrade")
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3140
Reported-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
We use 5.4 on all targets by default, and 4.19 has never been released
in a stable version. There is no reason to keep it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Extended attributes are required for overlayfs and have hence been long
ago enabled for jffs2, but should be enabled unconditionally for all
other filesystems which may potentially serve as overlayfs' upper
directory. Previously it was inconsistently added in multiple targets.
Add symbols to generic kernel config and remove all *_XATTR symbols
from target configs.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[keep things as they are for squashfs, improve commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Manually merged:
hack-5.4
230-openwrt_lzma_options.patch
bcm27xx
950-0283-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch
x86
011-tune_lzma_options.patch
Remove upstreamed patches in collaboration with Ansuel Smith:
ipq806x
093-1-v5.8-ipq806x-PCI-qcom-Add-missing-ipq806x-clocks-in-PCIe-driver.patch
093-2-v5.8-ipq806x-PCI-qcom-Change-duplicate-PCI-reset-to-phy-reset.patch
093-3-v5.8-ipq806x-PCI-qcom-Add-missing-reset-for-ipq806x.patch
All other modifications made by update_kernel.sh
Build-tested: bcm27xx/bcm2708, ipq806x, x86/64
Run-tested: ipq806x (R7800), x86/64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[update commit message/tested]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For many target we have added CONFIG_WATCHDOG_CORE=y to the target
config due to the following error:
Package kmod-hwmon-sch5627 is missing dependencies for the following
libraries:
watchdog.ko
However, actually the proper way appears to be setting the
dependency for the kmod-hwmon-sch5627 package, as the error message
demands.
Do this in this patch and remove the target config entries added
due to this issue.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It is deactivated everywhere, just set this in the generic config.
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
47a9f0d service: add method to query available container features
afbaba9 initd: attempt to mount cgroup2
ead60fe jail: use pidns semantics also for timens
759e9f8 jail: make use of BLOBMSG_CAST_INT64 for OCI rlimits
83053b6 instance: add instances into unified cgroup hierarchy
16159bb jail: parse OCI cgroups resources
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upstream commit 3d00da1de3 ("platform/x86: pcengines-apuv2: detect apuv4
board")
On 5.4, this module fails on APUv4 due to non-matching DMI data. With this
patch, the module will match DMI data for the APUv4.
Signed-off-by: Matthew Gyurgyik <matthew@gyurgyik.io>
[include upstream patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support Intel 10 Gigabit Ethernet Cards in x86/64 images by default.
This ensures that systems with cards such as the Intel x520 will work properly.
Signed-off-by: Gregory L. Dietsche <Gregory.Dietsche@cuw.edu>
Add a module description for the new pcengnies-apu2 device driver.
This driver supports the front button and LEDs on the PC Engines
APUv2/APUv3 boards.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Upstream in commit f9f8f0c24203 ("crypto: ccp -- don't "select"
CONFIG_DMADEVICES") removed dependency on CONFIG_DMADEVICES symbol which
leads to build breakage of ccp crypto module, so fix this by adding that
symbol back in the kernel config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.
This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.
For sunxi, this includes a trivial rename of the subtarget image
Makefiles.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
