All modifications made by update_kernel.sh/no human intervention needed
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[another refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The first gpio controller (gpio or gpio0) is always enabled by
default in the SoC DTSI files. No need to set status=okay in the
device DTS files a second time.
Remove the redundant statements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
None of the spi drivers on ath79 uses the num-cs property.
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
Some x86_64 single board computer (including Atomic Pi)
has onboard emmc, but requires CONFIG_MMC_SDHCI_ACPI driver
to use or boot from it.
Here is boot message for the mmc device
[ 2.838008] mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
[ 2.857536] mmc1: SDHCI controller on ACPI [80860F14:01] using ADMA
[ 2.950019] mmc0: new HS200 MMC card at address 0001
[ 3.158271] mmcblk0: mmc0:0001 M52516 14.6 GiB
[ 3.170290] mmcblk0boot0: mmc0:0001 M52516 partition 1 4.00 MiB
[ 3.177191] mmcblk0boot1: mmc0:0001 M52516 partition 2 4.00 MiB
[ 3.183963] mmcblk0rpmb: mmc0:0001 M52516 partition 3 4.00 MiB, \
chardev (248:0)
Other lines changed in this config file are introduced by menuconfig.
Signed-off-by: Mengyang Li <mayli.he@gmail.com>
Remove the MDIO reset from the MAC mode for the AR934x SoC family.
The reset is currently also defined for the MDIO node, where the reset
is acquired exclusively.
In case the ethernet node is enabled, this triggers a warning, as the
reset is already acquired by the MAC.
Signed-off-by: David Bauer <mail@david-bauer.net>
The TPLink CPE devices CPE210/CPE510 based on ar9344 have a build-in
Low Noise Amplifier on both of the 2x2 mimo rx chains.
This patch activates those two LNAs in the respective receiving chains
and hence improves the RX sensitivity by about 20dB.
Tested on CPE510 v2 & v3.
Signed-off-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Acked-by: Robert Marko <robimarko@gmail.com>
In this new setup the switch is treated as wan, lan1.100 is used as
our mgmt vlan.
The board mac is applied to eth0, switch and switch.1
The board mac is assigned with the LA bit set to all lan ports while
incrementing it.
Signed-off-by: John Crispin <john@phrozen.org>
Because the bug described in FS#2428 has been fixed with bf2870c1d9
("kernel: fix mtd partition erase < parent_erasesize writes") these
devices can now safely do sysupgrade.
Restore sysupgrade support disabled in:
0cc87b3bac ("ath79: image: disable sysupgrade images for routerstations
and ja76pf2")
cc5256a8bf ("ath79: base-files: disable sysupgrade for routerstations
and ja76pf2")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[move Build block, remove check-size argument, wrap sysupgrade line,
make commit message easier to read]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This will explain what is actually occuring on dd invocations.
Additionally remove comments for steps which are described by printed
statements anyway.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This will explain what is actually occuring on dd invocations.
Additionally remove comments for steps which are described by printed
statements anyway.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This fixes tethering with devices using iOS 14. Prior to this patch,
connections to remote endpoints were not possible while data transfers
between the OpenWrt device and the iOS endpoints worked fine.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch fixes build of squashfs image on lantiq. Currently the FEATURE
variable is overwritten by the subtarget.
Fixes: FS#3480
Fixes: f1c6523376 ("lantiq: clean up target/subtarget features")
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[reformat Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: MediaTek MT7621ST (880 MHz)
FLASH: 16 MiB (Macronix MX25L12835FM2I-10G)
RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
WiFi: MediaTek MT7603EN bgn 2x2:2
WiFi: MediaTek MT7612EN an 2x2:2
BTN: Reset, WPS
LED: - Power
- WiFi 2.4 GHz
- WiFi 5 GHz
- WAN
- LAN {1-4}
- USB {1-2}
UART: UART is present as pin hole next to the aluminium capacitor.
3V3 - RX - GND - TX / 115200-8N1
3V3 is the nearest on the aluminium capacitor and nut hole (pin1).
USB: 2 ports
POWER: 12VDC, 1.5A (Barrel 5.5x2.1)
Installation:
Via TFTP:
Set your computers IP-Address to 192.168.1.75
Power up the Router with the Reset button pressed.
Release the Reset button after 5 seconds.
Upload OpenWRT sysupgrade image via TFTP:
tftp -4 -v -m binary 192.168.1.1 -c put IMAGE
MAC addresses:
0x4 *:98 2g/wan, label
0x22 *:9c
0x28 *:98
0x8004 *:9c 5g/lan
Though addresses are written to 0x22 and 0x28, it appears that the
vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the
same here.
Signed-off-by: Pavel Chervontsev <cherpash@gmail.com>
[add MAC address overview, add label-mac-device, fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixup dfa357a3de "mvebu: base-files: Update Turris Omnia U-Boot
environment" which should have included this file as well.
By rebasing the initial patch this file somehow disappeared.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
[explain fixup in commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Move the update procedure from sysupgrade to first boot, which is much
more convenient in the sysupgrade case (otherwise the environment is
always one generation behind).
Check whether we have an old U-Boot release installed, and update the
environment only if necessary.
Some notes on the U-Boot environment:
The first 9 lines are a copy of the default environment of the old U-Boot
release - only modified, to run "distro_bootcmd", in case "mmcboot" fails
to boot the factory OS.
The remaining 16 lines are a backport of the default environment of the
new U-Boot release (shipped with CZ11NIC23). The main entry point is
"distro_bootcmd", which eventually sources boot.scr. This way, we have
a unified boot protocol for all Turris Omnia revisions so far.
This commit also fixes a shortcoming of previous Turris Omnia support:
Users may install OpenWrt with the Turris Omnia in factory state
(i.e. invalid environment store). In that case, neither fw_setenv, nor
U-Boot itself, would import the default environment from the image -
screwing up the rescue system, at least!
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
In contrast to the U-Boot version shipped with older versions of Turris
Omnia (CZ11NIC13, CZ11NIC20), the version shipped with Turris Omnia 2019
(CZ11NIC23) relies on the existence of /boot.scr.
Consequently, add a suitable boot script to the sysupgrade image.
Flash instructions for Turris Omnia 2019:
- Download openwrt-...-sysupgrade.img.gz, gunzip it, and copy the resulting
.img file to the root of a USB flash drive (FAT32 or ext2/3/4).
- Enter a rescue shell: Either via 5-LED reset and ssh root@192.168.1.1
on LAN port 4, or via 7-LED reset and the serial console.
- Insert the USB drive and mount it:
mkdir /mnt; mount /dev/sda1 /mnt
- Flash the OpenWrt image to eMMC:
dd if=/mnt/openwrt-...-sysupgrade.img of=/dev/mmcblk0 bs=4096 conv=fsync
- Reboot.
Flash instructions using a temporary "medkit" installation were written for
the older versions of Turris Omnia, and will *not* work on the Turris Omnia
2019.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Hauke wrote:
> We want to run some processes in the procd-ujail, this works when we
> use a SquashFS image and an overlay file system, but when we use an
> initramfs it does not work.
> [...]
> When we switch from initramfs to tmpfs, it is working, we added this
> code to target/linux/generic/other-files/init to make [it] work.
Move files to newly mounted tmpfs and then use switch_root to chroot
into new rootfs and free initramfs.
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Recent kernel bumps & target patch refactors have left some patch fuzz
around. Refreshed kernel patches using update_kernel script.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Removed since could be reverse-applied by quilt and found to be
included upstream:
backport-5.4/789-net-usb-qmi_wwan-Set-DTR-quirk-for-MR400.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/generic
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64 build/run]
custom-initramfs-uimage was replaced by calls to uImage, but apparently
mtc_wr1201 was missed in the transistion. Use uImage for this device
too.
Fixes: 9f574b1b87 "ramips: mt7621: drop custom uImage function"
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Strictly, an SPDX identifier requires a space between the comment
marker and the identifier itself. The choice of the comment marker
itself is irrelevant.
Correct:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
Wrong:
//SPDX-License-Identifier: GPL-2.0-or-later OR MIT
Fix that in the whole tree (actually, only ramips contained wrong
uses).
Found by checkpatch.pl
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for Xiaomi's Mi Router 4C device.
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com>
[wrap commit message, bump PKG_RELEASE for uboot-envtools, remove
dts-v1 from DTS, fix LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This function eliminates false-positive errors emitted by dd.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[drop argument check changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is already done by get_partitions.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[add "redundant" to title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is already done by get_partitions.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[add "redundant" to title, remove declaration of magic variable]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
UIMAGE_MAGIC is now supported by Build/uImage, in addition to
UIMAGE_NAME. This removes the need for a custom mkimage call, so let's
remove it.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Replace NETGEAR_KERNEL_MAGIC by UIMAGE_MAGIC to better match the
variable's purpose. This allows to drop the custom
Build/netgear-uImage.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[keep UIMAGE_MAGIC definitions even for default value]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use the mkimage argument overrides provided by uImage to implement the
customisations required for the initramfs, instead of the near-identical
custom function.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sort patches according to target/linux/generic/PATCHES. Additionally:
- replace hashes in backported patches with the ones from main Linux tree
- add descriptions to some patches
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[remove 004-add_sata_disk_activity_trigger.patch separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove 004-add_sata_disk_activity_trigger.patch, as the trigger is
already added in shared dtsi.
Suggested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are:
- smaller form factor
- different LED GPIOs
- different switch connections
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v5.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
FCC ID: A8J-EAP300A
Engenius EAP300 v2 is an indoor wireless access point with a
100/10-BaseT ethernet port, 2.4 GHz wireless, internal antennas,
and 802.3af PoE.
**Specification:**
- AR9341
- 40 MHz reference clock
- 16 MB FLASH MX25L12845EMI-10G
- 64 MB RAM
- UART at J1 (populated)
- Ethernet port with POE
- internal antennas
- 3 LEDs, 1 button (power, eth, wlan) (reset)
**MAC addresses:**
phy0 *:d3 art 0x1002 (label)
eth0 *:d4 art 0x0/0x6
**Installation:**
- if you get Failsafe Mode from failed flash:
only use it to flash Original firmware from Engenius
or risk kernel loop or halt which requires serial cable
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fdf0000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
*DISCLAIMER*
The Failsafe image is unique to Engenius boards.
If the failsafe image is missing or damaged this will not work
DO NOT downgrade to ar71xx this way, can cause kernel loop or halt
The easiest way to return to the OEM software is the Failsafe image
If you dont have a serial cable, you can ssh into openwrt and run
`mtd -r erase fakeroot`
Wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery** (unstable / not reliable):
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board while holding or pressing reset button repeatedly
NOTE: for some Engenius boards TFTP is not reliable
try setting MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software of EAP300 v2 is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel size to be no greater than 1536k
and otherwise the factory.bin upgrade procedure would
overwrite part of the kernel when writing rootfs.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[clarify MAC address section, bump PKG_RELEASE for uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The feature "squashfs" is defined for target and all subtargets
individually. Remove the redundant entries in the subtargets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move features common to all subtargets to the parent target.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[split patch to make it target-specific, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Replace my o2.pl email address.
I'm still available at the old address.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Manually rebased patches:
ath79/patches-5.4/910-unaligned_access_hacks.patch
bcm27xx/patches-5.4/950-0135-spi-spi-bcm2835-Disable-forced-software-CS.patch
bcm27xx/patches-5.4/950-0414-SQUASH-Fix-spi-driver-compiler-warnings.patch
ipq806x/patches-5.4/093-4-v5.8-ipq806x-PCI-qcom-Use-bulk-clk-api-and-assert-on-error.patch
Removed since could be reverse-applied by quilt and found to be included upstream:
ipq806x/patches-5.4/096-PCI-qcom-Make-sure-PCIe-is-reset-before-init-for-rev.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[refresh altered targets after rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
qca9558_devolo_dvl1xxx.dtsi contains device specific nodes which
are inherited for some DTS files and overwritten for others.
This is considered confusing, so move the relevant nodes/properties
to the devices and only keep the shared stuff in the DTSI.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[clarify commit title/message, move &gmac_config in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access
point. Serial port access for debricking requires fine soldering.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE
Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM boot log:
Using interface ath0 with hwaddr b0:...:3e and ssid "..."
Using interface ath10 with hwaddr b0:...:3f and ssid "..."
Tested by forum user blinkstar88
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link EAP225-Outdoor v1 is an AC1200 (802.11ac Wave-2) pole or wall
mount access point. Debricking requires access to the serial port, which
is non-trivial.
Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (AR8033): 1× 1GbE, PoE
Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface
Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
* Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:
ath0 Link encap:Ethernet HWaddr D8:...:2E
ath10 Link encap:Ethernet HWaddr D8:...:2F
br0 Link encap:Ethernet HWaddr D8:...:2E
eth0 Link encap:Ethernet HWaddr D8:...:2E
Tested by forum user PolynomialDivision on firmware v1.7.0.
UART access tested by forum user arinc9.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link EAP245 v1 is an AC1750 (802.11ac Wave-1) ceiling mount access point.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9880): a/n/ac, 3x3
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE
Flashing instructions:
* Upgrade the device to firmware v1.4.0 if necessary
* Exploit the user management page in the web interface to start telnetd
by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`.
* Immediately change the malformed username back to something valid
(e.g. 'admin') to make ssh work again.
* Use the root shell via telnet to make /tmp world writeable (chmod 777)
* Extract /usr/bin/uclited from the device via ssh and apply the binary
patch listed below. The patch is required to prevent `uclited -u` in
the last step from crashing.
* Copy the patched uclited programme back to the device at /tmp/uclited
(via ssh)
* Upload the factory image to /tmp/upgrade.bin (via ssh)
* Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt.
--- xxd uclited
+++ xxd uclited-patched
@@ -53796,7 +53796,7 @@
000d2240: 8c44 0000 0320 f809 0000 0000 8fbc 0010 .D... ..........
000d2250: 8fa6 0a4c 02c0 2821 8f82 87b8 0000 0000 ...L..(!........
-000d2260: 8c44 0000 0c13 45e0 27a7 0018 8fbc 0010 .D....E.'.......
+000d2260: 8c44 0000 2402 0000 0000 0000 8fbc 0010 .D..$...........
000d2270: 1040 001d 0000 1821 8f99 8374 3c04 0058 .@.....!...t<..X
000d2280: 3c05 0056 2484 a898 24a5 9a30 0320 f809 <..V$...$..0. ..
Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via the LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
Tested on the EAP245 v1 running the latest firmware (v1.4.0). The binary
patch might not apply to uclited from other firmware versions.
EAP245 v1 device support was originally developed and maintained by
Julien Dusser out-of-tree. This patch and "ath79: prepare for 1-port
TP-Link EAP2x5 devices" are based on that work.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link has developed a number of access points based on the AP152
reference board. In the EAP-series of 802.11ac access points, this
includes the following devices with one ethernet port:
* EAP225 v1/v2
* EAP225 v3
* EAP225-Outdoor v1
* EAP245 v1
Since the only differences between these devices are the ath10k wireless
radios and LEDs, a common base is provided for the overlapping support
requirements.
Hardware commonalities:
* SoC: QCA9563-AL3A MIPS 74kc v5.0 @ 775MHz, AHB @ 258MHz
* RAM: 128MiB DDR2 @ 650MHz
* Flash: 16MiB SPI NOR
* Wi-Fi 2.4GHz: provided by SoC
* Wi-Fi 5Ghz: ath10k chip on PCIe
* Ethernet: AR8033-AL1A, one 1GbE port (802.3at PoE)
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This commit add a workaround for non working SGMII link observed on some
QCA956x SoCs. The workaround originates part from the U-Boot source code
from QCA, part from the implementation from TP-Link found in the GPL
tarball for the EAP245v1.
Extends commit 0d416a8d3b for QCA956x.
Note that reset is the same on QCA955x and QCA956x, same register offset
and values.
Auto calibration is done on u-boot, but always fall back to default value
0x7. Add a DTS entry serdes-cal in case a device require another value.
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
[Sander Vanheule:
Minor code style fixes,
Remove hunk adding qca956x-serdes-fixup to a missing DTS,
Remove variable err that was only assigned,
Rename function to sgmii_serdes_init,
Lower priority of serdes call message to pr_debug]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Some bootloaders do not set up gmac0 properly, leaving it disconnected
from the sgmii interface. If the user specificies phy-mode sgmii, then
use the gmac-config/device node to ensure the mux is configured
correctly.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses
the same Armada-3720 SoC with extended hardware support.
- SoC: Armada-3720
- RAM: 1 GB DDR4
- Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC
- Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE)
- WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB)
- 1x USB 2.0 port
- 1x USB 3.0 port
- 1x microSD slot
- 1x mini-PCIe slot (USB [with nano-sim slot])
- 1x mini-USB debug UART
- 1x RTC Clock and battery
- 1x reset button
- 1x power button
- 4x LED (RGBY)
- Optional 1x M.2 2280 slot
** Installation **
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/
linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb
bin/targets/mvebu/cortexa53/
$ in.tftpd -L -s bin/targets/mvebu/cortexa53/
Connect to the device UART via microUSB port on the back side and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Ping server to confirm network is working:
$ ping $serverip
Using neta@30000 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
$ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb
Set the console and boot the image:
$ setenv bootargs $console
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
This patch add missing support of SC16IS740 serial controller, installed
on LS1012A-FRDM board.
It was required to change RCW bits, because SPI was disabled by default.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This will make developing process easier, because dtb will be included
into image.
Not need to enable initramfs image by default.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Currently sfp_select_interface() return the fastest interface that
the sfp modules supports even if the phy don't support that mode.
For example an GPON module that support both 2500basex and 1000basex.
Currently sfp_select_interface() picks 2500basex instead of 1000basex.
So limit the interfaces which both sides supports before calling
sfp_select_interface() or return an error if we don't have match.
Reviewed-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Braihan Cantera <bcanterac@gmail.com> [MikroTik RB760iGS + Nokia G-010S-A 3FE46541AA SFP]
Tested-by: John Thomson <git@johnthomson.fastmail.com.au> [Mikrotik rb760igs + SFP SM/LC, SFP base1000T, SFP+ passive DAC]
Signed-off-by: René van Dorst <opensource@vdorst.com>
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait
The change to split only on the last colon between mtd-id and partitions
will cause newpart to see following string for the first partition:
KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive)
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: d6a9a92e32 ("kernel: bump 5.4 to 5.4.69")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The OpenMesh related files were not updated since a while and the new
coding style requirements weren't integrated. This can cause problems
for new devices when an author uses these files as starting point.
* use SPDX-License-Identifiers instead of full license texts
* drop linux,default-trigger with value default-off for LEDs
* led nodes with label "abc:xyz" should have name "xyz_abc"
* led DT labels for "xyz_abc" should be "led_xyz_abc"
* "m25p80@0" flash node should be renamed to "flash@0"
* drop unnecessary empty lines
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[minor commit title and message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v4.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
This patch adds support for the WiFi Pineapple Mark 7, a wireless
penetration testing tool.
Specifications:
* SoC: MediaTek MT7628 (580MHz)
* RAM: 256MiB (DDR2)
* Storage 1: 32MiB NOR (SPI)
* Storage 2: 2GB eMMC
* Wireless 1: 802.11b/g/n 2.4GHz (Built In)
* Wireless 2: 802.11b/g/n 2.4GHz (MT7601)
* Wireless 3: 802.11b/g/n 2.4GHz (MT7601)
* USB: 1x USB Type-A 2.0 Host Port
* Ethernet: 1x USB Type-C AX88772C Ethernet
* UART: 57600 8N1 on PCB
* Inputs: 1x Reset Button
* Outputs: 1x RGB LED
* FCCID: 2AA52MK7
Flash Instructions:
Original firmware is based on OpenWRT.
Use sysupgrade via SSH to flash.
Signed-off-by: Marc Egerton <foxtrot@realloc.me>
[pepe2k@gmail.com: set only required/used gpio groups to gpio function]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
New batches of the R36A board series might no longer keep separated
Ethernet MAC addresses stored in flash. Use same approach as on the
N2Q and calculate Ethernet MACs from WLAN one which is kept in ART.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network Pi-WiFi4 is a Qualcomm QCA9531 v2 based, high-power 802.11n
WiFi board in Raspberry Pi 3B shape, equipped with 1x FE and 4x USB 2.0.
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16+ MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM
- 2x IPEX/U.FL connectors on PCB
- 4x USB 2.0 Type-A
- Genesys Logic GL850G 4-port USB HUB
- USB power is controlled by GPIO
- 5x LED (3x on PCB, 2x in RJ45, 4x driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- 1x micro USB Type-B for power and system console (Holtek HT42B534)
- UART and GPIO (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The Xiaomi Mi Router 4A Gigabit model has a race condition on bootup
causing the SQUASHFS data errors to appear and create a bootloop
scenario.
Adding the m25p,fast-read property resolves this issue.
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CPU: Atheros AR9342 rev 3 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN 2.4GHz: Atheros AR9342 v3 (ath9k)
WLAN 5.0GHz: QCA988X
Ports: 2x GbE
Flashing procedure is identical to other ubnt devices.
https://openwrt.org/toh/ubiquiti/common
Flashing through factory firmware
1. Ensure firmware version v8.7.0 is installed.
Up/downgrade to this exact version.
2. Patch fwupdate.real binary using
`hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \
hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using
`chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
(copied from Ubiquiti NanoBeam AC and modified)
To keep it consistent, we will add the gen1 variant to
the nanobeam ac gen1.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This adds a missing ";;" in the switch-case in 11-ath10k-caldata.
Fixes: 4d36569b9c ("ath79: fix ath10k caldata extraction on some
D-Link DIR-842 C3 devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to forum threads [0][1] and a report on IRC by Doc-Saintly
some of those boards have calibration data in a different place. Only
one alternative location is known.
Without proper board calibration data (board.bin having all 0xff bytes)
ath10k firmware still tries to load but crashes on startup with a
confusing error message.
If you're applying this patch manually on your device do not forget to
remove /lib/firmware/ath10k/pre-cal-pci-0000:00:00.0.bin and reboot to
force caldata re-extraction.
[0] https://forum.openwrt.org/t/support-for-d-link-dir842-rev-c3/41654
[1] https://forum.openwrt.org/t/d-link-dir-842-cant-access-firmware-upload-form/65454
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
All targets that used mvsw61xx have switched to upstream mv88e6xxx DSA
driver, so it can be removed.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
mediatek frequently had mixed indent (tabs vs. spaces) in DTS files
and DTS file kernel patches (probably due to careless copy/paste).
The harmonizes these cases to tabs-only, as usual for DTS(I).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Both bcm2709 and bcm2710 firmware can run on the same RaspberryPi
models, varying however in 32 and 64 Bit architectures. The model name
alone does not include the architecture information, which becomes
problematic if looking at a overview that only contains the names. By
adding a variant it is possible to tell the architecture.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This pci@40000000 node from upstream was dropped when the device
was converted from local DTS(I) files to kernel patches in [1] to
ensure that change was purely cosmetic.
However, the DK04.1 has a PCI-E slot by default, so let's keep
(i.e. not remove) the kernel definition now.
[1] c4beac9ea2 ("ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1")
Suggested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A lot of patches are outdated versions of upstreamed patches and
drivers.
So lets pull in the upstreamed patches and reorder remaining ones.
This drops the unnecessary 721-dts-ipq4019-add-ethernet-essedma-node.patch
which adds nodes for not yet in OpenWrt IPQESS driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[do not touch 902-dts-ipq4019-ap-dk04.1.patch here]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Define wildcard patterns for filtering in target/linux/generic/config-filter
Preparation for supporting newer kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MikroTik recently changed again the way they store wlan calibration data
on devices. Prior to this change, ERD calibration data for all available
radios was stored within a single identifier node ("tag" in RouterBoot
parlance).
Recent devices have been seen with calibration (and BDF) data stored in
separate identifiers within LZOR packing for each radio: this patch
addresses this by:
1) ensuring that both variants are properly supported,
2) preserving backward compatibility with existing data consumers,
3) allowing for more than 2 calibration blobs to be exposed via sysfs.
Specifically, before this patch, the driver would provide a single sysfs
file named /sys/firmware/mikrotik/hard_config/wlan_data that contained
whatever calibration data found on the device's flash. After this patch,
when executed on a device that uses the old style storage, this behavior
is unchanged, but when executed on a device that uses new style storage
(for either traditional "ERD" packing or "LZOR" packing), the driver
replaces that single file with a folder containing one or more files
each containing the data encoded within individual identifiers.
As far as OpenWRT is concerned, this means that for devices which are
known to exist with both styles of data storage, a suitable hotplug stub
could look like this for e.g. the second radio:
wdata="/sys/firmware/mikrotik/hard_config/wlan_data"
( [ -f "$wdata" ] && caldata_sysfsload_from_file "$wdata" 0x8000 0x2f20 ) || \
( [ -d "$wdata" ] && caldata_sysfsload_from_file "$wdata/data_2" 0x0 0x2f20 )
This patch has been tested with LZOR old and new style packing on ipq4019,
and with old style on ath79.
Tested-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Шебанов Алексей <admin@ublaze.ru>
Tested-by: Alen Opačić <subixonfire@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Robert Marko <robimarko@gmail.com>
CONFIG_EFI_VARS has been disabled in
64bit x86 target in 2018 by the following commit
b0a51dab8c
the same reasons apply to Generic target, so
now it's disabled here too.
Leaving it enabled is also blocking compile as
a new symbol was added
EFI_CUSTOM_SSDT_OVERLAYS
that depends from CONFIG_EFI_VARS
and the build system stops and waits for
user input on what to do about it.
The Legacy and Geode targets never
had any EFI_xxx configs enabled so they
don't have this issue
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
This adds support for RTL839x SoCs in the ethernet and switch
drivers of the rtl838x architecture.
Reviewed-by: Andreas Oberritter <obi@saftware.de>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This device has previously been supported by the image
for Xiaomi Mi Router 3G v2. Since this is not obvious, the
4A is marketed as a new major revision and it also seems to
have a different bootloader, this will be both more tidy and
more helpful for the users.
Apart from that, note that there also is a 100M version of
the device that uses mt7628 platform, so a specifically named
image will also prevent confusion in this area.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
E600G v2 based on Qualcomm/Atheros QCA9531
Specification:
- 650/600/200 MHz (CPU/DDR/AHB)
- 128/64 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz
- 2 x 10/100 Mbps Ethernet(RJ45)
- 1 x MiniPCI-e
- 1 x SIM (3G/4G)
- 5 x LED , 1 x Button(SW2-Reset Buttun), 1 x power input
- UART(J100) header on PCB(115200 8N1)
E600GAC v2 based on Qualcomm/Atheros QCA9531 + QCA9887
Specification:
- 650/600/200 MHz (CPU/DDR/AHB)
- 128/64 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz
- 1T1R 5 GHz
- 2 x 10/100 Mbps Ethernet(RJ45)
- 6 x LED (one three-color led), 2 x Button(SW2-Reset Buttun),1 x power input
- UART (J100)header on PCB(115200 8N1)
Flash instruction:
1.Using tftp mode with UART connection and original OpenWrt image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ath79-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to OpenWrt:
run lfw
- After that the device will reboot and boot to OpenWrt.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original OpenWrt image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ath79-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to OpenWrt.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[rearrange in generic.mk, fix one case in 04_led_migration, update
commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The file lacks executable permissions, which makes it not being applied
during the first boot.
While at it, drop unneeded include.
Signed-off-by: Piotr Jurkiewicz <piotr.jerzy.jurkiewicz@gmail.com>
[do not touch board name handling, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DIR-2640 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue),
WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: James McGuire <jamesm51@gmail.com>
[fix device definition title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The comment content can be useful for readers of both the log and code
Previously when dd command "records in/out" messages are not filtered
like now with get_image_dd, it's not clear that these messages are for
extracting boot sectors. E.g.
Before
== upgrade: Reading partition table from bootdisk...
37+26 records in
37+26 records out
== upgrade: Reading partition table from image...
After
== upgrade: Reading partition table from bootdisk...
== upgrade: Extract boot sector from the image
37+26 records in
37+26 records out
== upgrade: Reading partition table from image...
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
