This adds a "factory" image for the aircube-isp devices. Note that the
firmware can't be uploaded without prior special preparation. For the
most recent instructions on how to do that, visit the OpenWRT wiki page
of the Ubiquiti airCube ISP for details:
https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp
Current procedure:
With the original firmware 2.5.0 it is possible to upload and execute a
script via the configuration. To do that download and unpack the
original configuration, adapt uhttpd config to execute another lua
handler (placed in the config directory) and pack and upload it again.
The lua handler can call a script that mounts an overlayfs and modifies
the "fwupdate.real" binary so that an unsigned image is accepted. The
overlayfs is necessary because a security system (called tomoyo) doesn't
allow binaries in other locations than /sbin/fwupdate.real (and maybe
some more) to access the flash when executed via network.
A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for
finding out how to patch the binary so that it accepts an unsigned
image.
The current step-by-step procedure is:
- Use a version 2.5.0 of the original firmware. This is important
because a binary file will be modified.
- Download a configuration.
- Unpack it (it's just a tar gz file without an ending).
- Add the following to uhttpd:
``````
config 'uhttpd' 'other'
list listen_http 0.0.0.0:8080
list listen_http [::]:8080
option 'home' '/tmp/persistent/config/patch/www'
option lua_prefix '/lua'
option lua_handler '/tmp/persistent/config/patch/handler.lua'
``````
- Create a `patch` subfolder.
- Create a `patch/www` subfolder.
- Create a `patch/handler.lua` with the following content:
``````
function handle_request(env)
uhttpd.send("Status: 200 OK\r\n")
uhttpd.send("Content-Type: text/plain\r\n\r\n")
local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1"
local proc = assert(io.popen(command))
for line in proc:lines() do
uhttpd.send(line.."\r\n")
end
proc:close()
end
``````
- Create a `patch/patch.sh` with the following content:
``````
#!/bin/sh -x
set -e
set -u
set -x
UBNTBOX_PATCHED="/tmp/fwupdate.real"
MD5FILE="/tmp/patchmd5"
cat <<EOF > ${MD5FILE}
c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real
EOF
# check md5 of files that will be patched
if ! md5sum -c ${MD5FILE}
then
echo "******** Error when checking files. Refuse to do anything. ********"
exit 0
fi
# prepare some overlay functionality
LOWERDIR="/tmp/lower_root"
mkdir -p ${LOWERDIR}
mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR}
overlay_some_path()
{
PATH_TO_OVERLAY=$1
ALIAS=$2
UPPERDIR="/tmp/over_${ALIAS}"
WORKDIR="/tmp/over_${ALIAS}_work"
mkdir -p ${UPPERDIR}
mkdir -p ${WORKDIR}
mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY}
}
# patch the ubntbox binary.
overlay_some_path "/sbin" "sbin"
echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598
echo "******** Done ********"
``````
- Repack the configuration.
- Upload it via the normal web interface.
- Wait about a minute. The webserver should restart.
- Now there is a second web server at port 8080 which can call the lua
script. Visit the page with a web browser. Link is for example
http://192.168.1.1:8080/lua
- You should see the output of the script with a "*** Done ***" at the
end. Note that the patches are not permanent. If you restart the
router you have to re-visit the link (but not re-upload the config).
- Now you can upload an unsigned binary via the normal web interface.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
The factory image for the dlink_dir-615-e4 is getting too big which makes
the full ath79 tiny build fail, deactivate it by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
The full address assignment is as follows:
LAN label
WAN label + 1
5G label
2G label - 1
This patch changes all devices using TL-WDR4300 board:
TL-WDR3600 v1 (checked on device)
TL-WDR4300 v1 (checked on device)
TL-WDR4300 v1 (IL)
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase/extend commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This enables using 4kiB sectors as erase blocks for 4MiB NOR flash ICs
that support it.
Writeable jffs2 overlay used to store settings requires a partition with
at least 5 erase blocks, so using small sectors is essential for devices
with 4MiB flash.
Sysupgrading a device running firmware without this feature will likely
not allow to preserve configs automatically but since ath79 is
considered to be in a "technology preview" state it shouldn't be a
problem.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Specifications:
- FCC ID: KA2IR615E3
- SoC: MIPS32 24K 400 MHz Atheros AR7240
- RAM: 32 MiB DDR SDRAM ESMT M13S2561616A-5T
- Flash: 4 MiB NOR SPI Macronix MX25L3208E
- Wireless: AR9287 2.4 GHz 802.11n 2T2R, 2x RP-SMA connectors
- Ethernet: 5x 100BASE-TX Fast Ethernet
- LEDs: 9x GPIO, 1x ath9k
- Buttons: 2x tactile switches
- UART: 3.3 V, 115200 8n1
- USB: simple hardware modification required, 1x USB 1.1 Full Speed
Partitioning notes:
Vendor firmware (based on CameoAP99) defines two additional partitions:
"mac" @0x3b0000, size 0x10000 and "lp" @0x3c0000, size 0x30000.
The "mac" partition stores LAN MAC address and hardware board name.
However, the vendor firmware uses addresses from "nvram" partition, and
the board name is used only for informational purposes in the Web
interface (included in the pages' header), not affecting the firmware
image check.
The "lp" partition is supposed to contain a "language pack" (which can
be used to add an additional language support to the Web interface) and
is flashed separately, using the vendor firmware upgrade page.
Since these partitions are absolutely useless for OpenWrt and
overwriting them doesn't prevent downgrading to obsolete vendor
firmware, this patch appends the valueable space to "firmware".
Installation instructions:
- Upgrade from OpenWrt ar71xx with "sysupgrade -f -n"
or
- Upload as a firmware update via the vendor Web-interface
or
- Connect UART and use "loady" to upload and run OpenWrt initramfs
image, then sysupgrade from it (TFTP client doesn't work)
or
- Before powering up hold "reset" button and keep it pressed for about
15 seconds after, then access fail safe Web server on 192.168.0.1 (the
old uIP TCP/IP protocol stack is not compatible with modern Linux, the
kernel, so you'll need to use some other OS to do this). Can be
performed without a Web-browser too:
curl http://192.168.0.1/cgi/index \
-F Send=@openwrt-ath79-tiny-dlink_dir-615-e4-squashfs-factory.bin
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Netgear WNDR routers (AR9344 models) like WNDR4300 have 128 MiB of flash
memory but only first 32 MiB are used now - both by vendor's firmware and
OpenWrt. This patch concatenates two regions of flash memory: ubi part
of firmware partition and reserved (unused) space beyond 'caldata_backup'
while preserving ART backup. No data is wiped or moved away.
This increases area for OS ubi volumes from 23 to 119 Megabytes.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This partially reverts commit 32144ba275.
This commit replaced gpio-exports in favor of gpio-hogs for enabling USB
power at boot, but this rids the user of control of the USB port power
present on this device for a long time. It was agreed on a mailing list
[1] that this is not the way to go, and this patch breaks a very common
use-case of WWAN modem reset by power cycle, used on a lot USB equipped
routers, hence revert this change until a better solution can be found.
[1] http://lists.infradead.org/pipermail/openwrt-devel/2019-November/020151.html
Tested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TL-WDR4300 board uses only green LED names in DTSI.
This patch adds migration for them.
The actual LED colors on the devices have been reported to vary
across subrevisions (v1.x). Despite, the USB LEDs on the back might
have different color than the other LEDs on the front.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.
Thanks to Josh4300 for testing on device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The variables UBNT_BOARD and UBNT_VERSION are defined in the parent
Device/ubnt definition and then overwritten for most of the derived
platform definitions (e.g. Device/ubnt-wa).
Since this mixed use of inheritance and overwriting can be misleading,
this moves the variables to the platform-based definitions.
While at it, reorder the definitions to have order consistent, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"[...] the size component shall be zero."
(See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1"
section "4.1.1 Open Firmware-defined Properties for Child Nodes")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
* SoC: Atheros AR9342-BL1A
* RAM: 64MB DDR2 (Winbond W9751G6KB-25)
* Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G)
* Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support
* Wifi 2.4GHz: Atheros AR9340 v2
* WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2)
* LEDs: 1x Power, 1x Ethernet
* Buttons: 1x Reset
* UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port
The LEDs do not seem to be connected to any GPIO, so there is currently
no way to control them.
Installation via U-Boot, TFTP and serial console:
* Configure your TFTP server with IP 192.168.1.254
* Connect serial console and power up the device
* Hit any key to stop autoboot
* tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin
* bootm 0x81000000
* copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
to /tmp
* sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The sysupgrade image contains OpenWrt specific metadata. Having this
metadata in the factory images makes no sense. Drop IMAGE/factory.bin
from Device/ubnt-wa and use the default from Device/ubnt instead.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In d421a8b944 ("ath79: read label MAC address from flash instead
of using phy0/phy1") the source of the label MAC address was changed
for devices just reading it from phy0. To get rid of the dependency
from phy startup, addresses were read directly from the flash
locations that are used to initialize the phy MAC addresses.
Unfortunately, it turned out that Ubiquiti XM devices seem to have
different flash locations than expected, and also seem to have
specific locations for different devices (all in art/EEPROM):
0xe012 AR9280 Nanostation M2 - 0x120c
0xe035 AR9280 Nanostation M3 - 0x120c
0xe1b2 AR9280 Rocket M2 - 0x120c
0xe1c3 AR9280 Rocket M3 - 0x120c
0xe1b5 AR9280 Rocket M5 - 0x120c
0xe2d5 AR9280 Bullet M2 Titanium - 0x120c
0xe2b5 AR9280 Nanobridge M5 - 0x120c
0xe202 AR9280 Bullet M2 - 0x120c
0xe232 AR9287 Nanobridge M2 - 0x110c
0xe4a2 AR9285 AirRouter - 0xa0bf
Picostation M2 - 0x120c and 0xa0bf
Nanostation Loco M2 - not in 0x120c, other locations not checked
An additional problem of the Ubiquiti device support in OpenWrt is
that we provide images that match several subvariants of the devices,
which might have different MAC address locations.
Given that reading the address from phy0 in 02_network _is_ working
for the ath79 target in general, it does not seem reasonable to
rebuild a complex MAC address retrieval mechanism which is already
present in the ath9k driver.
So, this patch reverts the label MAC address source for Ubiquiti XM
devices (and the Unifi AP) to /sys/class/ieee80211/phy0/macaddress.
This doesn't affect XW and Unifi AC devices, where the label MAC
address source is defined via device tree.
For alfa-network,ap121f the location 0x1002 is kept, as this has
been verified during device support preparation in PR #2199.
Fixes: d421a8b944 ("ath79: read label MAC address from flash
instead of using phy0/phy1")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).
The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)
Known issues:
- Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.
According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.
GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames all remaining occurrences of "EEPROM" to "art" to
further harmonize the partition labelling in ath79. This will
help to reduce the amount of user-space code and might be
beneficial when code is copy/pasted in the future.
Affected are only devices from Ubiquiti, where the XM board is
already using "art" in ath79.
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.
Specification:
- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
- XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
- A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
- XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
- A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
- XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
- A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore QCA9k based devices released in 2019 require a custom TFTP image
for U-Boot built-in recovery mode (triggered with reset button). Image
has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI
commands which will be executed later. Images without the custom header
will be ignored by U-Boot.
To be able to support both the vendor firmware (QSDK) and OpenWrt flash
layouts, used here commands change the 'bootcmd' before flashing image.
This commit adds generic helper script for YunCore devices with 16 MB of
flash and enables TFTP image generation for A770 model.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[pepe2k@gmail.com: commit description reworded, recipe renamed]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Ath10k packages were removed from ar71xx in master in commit
34113999ef ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes
FS#1743)") but ath79 in master and the 19.07 branch still suffer from
the issue.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The initial DTSI names for the TP-Link CPE devices have become
quite confusing, as several non-V1 devices now use the *-v1.dtsi,
the *cpe510-v1.dts does not use the cpe510.dtsi, etc.
This introduces a new naming scheme based on whether devices have
one or two ports, which should be easier to grasp.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This applies minor style improvements and removes commented pll
clock adjustments from ubnt_xm DTSI. The latter were introduced
(already commented out) when adding ath79 target and have never
been touched since then. For Unifi (BZ board), similar clock
adjustments are employed and used.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This adds the gpio switch to enable PoE passthrough on Ubiquiti
Nanostation (XM/XW).
Values are copied from the implementation in ar71xx.
GPIO values checked on:
- NanoStation M5 XW
- NanoStation M2 XM
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The WPS button was mapped to the restart/reset. This patch
changes it to emit the KEY_WPS_BUTTON keycode so pressing
the WPS button does initiate WPS.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
During the introduction of the ath79/nand images for the GL-AR300M
series the firmware partition label and compatible were altered,
but the necessary adjustments have not been made for the
GL-AR300M16 and the GL-AR300M-Lite. This will result in a
non-bootable partition setup for these devices.
This patch adds the necessary definitions to those two devices.
Fixes: 55e6c903ae ("ath79: GL-AR300M: provide NAND support;
increase to 4 MB kernel")
Fixes: b591cabd39 ("ath79: add GL.iNet GL-AR300M16 as NOR-only
board")
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
[extend commit message, alter commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ar71xx has just one board name "wndr3700" for WNDR3700 V1/V2,
WNDR3800 and WNDR3800CH, whereas ath79 provides separate images for
the boards. So, update SUPPORTED_DEVICES to store the correct
ar71xx board names.
Fixes: FS#2510
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As the former qca9558_tplink_archer-c7.dtsi is also used for
Archer C5 v1 this patch removes the number from the DTSI name
to indicate that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Those symbols were removed in kernel 4.16:
commit 4670d610d59233b017a6ea1fa25bbf06dabbff42
Author: Rob Herring <robh@kernel.org>
PCI: Move OF-related PCI functions into PCI core
Fixes: FS#2588
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but
were missing the rssileds package, while others that don't have
RSSI LEDS had the package included.
This commit includes the rssileds package only for those devices
that need it.
Tested on a NanoStation M XW.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The GL.iNet GL-AR750S has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.
This commit provides support for the NAND through the upstream
SPI-NAND framework.
At this time, the OEM U-Boot appears to only support loading the
kernel from NOR. This configuration is preserved as this time,
with the glinet,gl-ar750s-nand name reserved for a potential,
future, NAND-only boot.
The family of GL-AR750S devices on the ath79 platform now includes:
* glinet,gl-ar750m-nor-nand "nand" target
* glinet,gl-ar750m-nor "nand" target (NAND-aware)
NB: This commit increases the kernel size from 2 MB to 4 MB
"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar750s-nor firmware produced by this commit:
* glinet,gl-ar750s -- OpenWrt 19.07 ar71xx
* glinet,gl-ar750s -- OpenWrt 19.07 ath79
Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then
flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the
NAND-based variant.
Other upgrades to these images, including directly to the NAND-based
glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot.
NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which
enables flashing of NAND factory.img with the current GL-iNet U-Boot,
"U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)"
The GL-AR750S OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.
The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images
generated after this commit flash each other directly.
This commit changes the control of the USB VBUS to gpio-hog from
regulator-fixed introduced by commit 0f6b944c92. This reduces the
compressed kernel size by ~14 kB, with no apparent loss of
functionality. No other ath79-nand boards are using regulator-fixed
at this time.
Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid
The ar71xx targets are unmodified.
Cc: Alexander Wördekemper <alexwoerde@web.de>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The GL.iNet GL-AR300M series of devices includes variants without NAND
and only the 16 MB NOR flash. These include the GL-AR300M16 and the
GL-AR300M-Lite (already with its own board name).
This board-name addition provides disambiguation from the NAND-bearing
GL-AR300M devices, both for OpenWrt code and for end users.
Kernel and firmware support for NAND and UBI will add ~320 kB to the
overall firmware size at this time. This NOR-only option continues to
provide more compact firmware for both the GL-AR300M16 as well as
those who wish to use it as an alternate or primary, NOR-resident
firmware on the GL-AR300M.
The ar71xx targets are unmodified.
Installation
------------
Install through OEM U-Boot (HTTP-based) or `sysupgrade --force` when
booted from NOR and running OEM or OpenWrt, NOR-based firmware.
As one of the intentions is disambiguation from NAND-bearing units,
users who have flashed this firmware onto a device with NAND would
need to use U-Boot or `sysupgrade --force` to flash firmware that
again supports NAND.
There are no additional SUPPORTED_DEVICES as it is not possible to
determine if a device does or does not have NAND based on
either the OEM's or OpenWrt's board names prior to this patch.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The GL.iNet GL-AR300M has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.
This commit provides support for the NAND through the upstream
SPI-NAND framework. Devices with both NOR and NAND flash can support
independent firmware on each, with U-Boot able to boot from either.
The OEM U-Boot will fall back to the NOR firmware after three
"unsuccessful" boots.
The family of GL-AR300M devices on the ath79 platform now includes:
* glinet,gl-ar300m-lite "generic" target, NOR-only board
* glinet,gl-ar300m-nand "nand" target
* glinet,gl-ar300m-nor "nand" target (NAND-aware)
NB: This commit increases the kernel size from 2 MB to 4 MB
"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar300m-nor firmware produced by this commit:
* gl-ar300m -- OEM v3 NOR ar71xx (openwrt-ar300m16-*.bin)
* gl-ar300m -- OpenWrt 18.06 ar71xx
* gl-ar300m -- OpenWrt 19.07 ar71xx
Other upgrades to these images should be performed through U-Boot.
The GL-AR300M OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.
The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated
after this commit should safely flash each other using sysupgrade.
The boot counter is implemented by the OEM using u-boot-env. At this
time, it does not appear that the switch on the side of the unit can
be used to select NOR vs. NAND boot and the fail-over is only from
NAND to NOR. To save flash wear, it is only reset when running the
glinet,gl-ar300m-nand firmware.
NAND-specific base-files are used to remove impact on existing
generic and tiny targets.
As there is now no "generic" build appropriate for the GL-AR300M16,
(or for users of the GL-AR300M that do not need access to NAND)
it will be introduced in a subsequent commit.
Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid
The ar71xx targets are unmodified.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Linux 4.19 supplies the upstream spi-nand framework,
permitting porting and support of boards with SPI NAND.
* Adjusted nand/target.mk to provide FEATURES += squashfs nand
* Updated config-default to provide current MTD and UBI support
Defaults selected for:
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_LIMIT=20
# CONFIG_MTD_UBI_FASTMAP is not set
# CONFIG_MTD_UBI_GLUEBI is not set
The bad-block reservation limit technically should be 21 for Paragon
SPI NAND but most other devices in the class are 20 blocks per Gbit.
In Linux 5.2 this is specified on a per-chip basis through NAND_MEMORG
Contents adjusted to remove declarations provided at the target level
by commit 08a134820f (Oct 23, 2019) ath79: enable PCI for whole target
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Tested-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.
For future reference:
The MAC addresses of the FRITZ!WLAN Repeater 300E can be extracted
from the urlader key value store:
maca *:6B
macb *:6C
macwlan *:6D
macdsl *:6E
and be set by e.g.
addr=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ar71xx, the board name for the TL-WR1043ND v3 is equal to v2:
tl-wr1043nd-v2
Fix SUPPORTED_DEVICES for v3 in ath79 accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When Nanostation M was renamed from ubnt,nano-m to ubnt,nanostation-m
in commit f1396ac753 ("ath79: align naming of Ubiquiti Nanostation M"),
the caldata extraction in 10-ath9k-eeprom was overlooked.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In several DTS files, button nodes are just named buttonX or
xxx_button. This replaces the names with more specific names matching
the majority of key definitions.
While at it, fix name of keys node in one case.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link's TL-WR941 is sold with detachable antennas
internationally (ND version), but with fixed antennas in China
(N version). While hardware and images are similar for both
variants of v2 and v4, they are different for v6.
Having both explicitly will make it easier for user to identify
the correct image, and most importantly will raise awareness
that N and ND are not necessarily always the same as for
TL-WR841 series.
With an image selection webpage, using ALT0_MODEL as in this
patch will provide the option to list versions for N and ND
separately.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ð0 node is the same for all TP-Link CPE devices in ar9344,
so move it to parent DTSI. While at it, do some minor DTS
harmonizations.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for a popular low-cost 2.4GHz N based AP
Specifications:
SoC: Qualcomm Atheros QCA9533 (650MHz)
RAM: 64MB
Storage: 8 MB SPI NOR
Wireless: 2.4GHz N based built into SoC 2x2
Ethernet: 2x 100/10 Mbps, integrated into SoC
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This also applies some minor changes to the common DTSI:
- use &wmac for label-mac-device, as this one is actually set up in
common DTSI
- move ð0 to parent DTSI
- fix several leading spaces, added/removed newlines
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[DTS style fixes/improvements, updated commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.
Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with
two Ethernet ports based on Atheros AR9344
The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm
instead of 12 dBm) and two antenna connectors instead of built-in antennas.
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP: 192.168.0.100
Stock device TFTP adress: 192.168.0.254
The TP-Link WBS devices use the same GPIOs as the CPE devices,
except for the link4 LED. For this one, WBS devices use "2", while
CPE devices use "16". (Tested on WBS210 v2)
Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[added comment about GPIO]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are two recent commits stating to add support for Netgear
WNDR4300, where the second one seems to be just leftover from
an earlier patch having been rebased.
Since the first patch already provides support in the most recent
state, just revert the second one.
This reverts commit cd87272eb2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- QCA9558 Soc
- 720/800 (CPU/DDR)
- 1x 10/100/1000 Mbps WAN Ethernet
- 4x 10/100/1000 Mbps LAN Ethernet
- 64 MB RAM (DDR2)
- 8 MB FLASH
- QCA9558 2.4 GHz 802.11bgn
- 1x USB 2.0
Flash instruction
WebUI:
Download *-factory.bin image, rename to tp_firmware.bin and upload
it via the firmwary upgrade function of the stock firmware WebUI.
Tftp:
Rename OpenWRT or original firmware to wr1045v2_tp_recovery.bin and
Change your computer ip in 192.168.0.66 and subnet mask in 255.255.255.0.
Router will obtain IP 192.168.0.86 for a few seconds while loading,
when reset button pressed at power On.
Signed-off-by: Rasim Kalimullin <neutrino.vm@gmail.com>
[rebased onto base-files split]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC address for the wmac 2.4 GHz radio of the Ubiquiti UniFi AC
family of devices is actually embedded in the mtd-cal-data, so there
is no need for mtd-mac-address (which was incorrectly forcing wmac
to have the same MAC as eth0). This makes it coherent with the stock
firmware and the ar71xx target:
· XX:XX:XX:X0:XX:XX eth0
· XX:XX:XX:X1:XX:XX ath0/wlan1 (2.4 GHz)
· XX:XX:XX:X2:XX:XX ath1/wlan0 (5 GHz)
Checked on a UniFi AC Mesh, a UniFi AC LR and a UniFi Lite.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
On nand subtarget, the default upgrade mechanism should be
nand_do_upgrade. This patch changes platform_do_upgrade()
accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For several devices, wmac MAC address is set from art 0x1002
explicitly by using mtd-mac-address although mtd-cal-data is
pulled from art 0x1000.
With the MAC address in 0x1002, the driver should automatically
use it when reading caldata from 0x1000. Thus, remove the
redundant mtd-mac-address for those devices.
This patch addresses the cases where the calibration data partition
is not labelled art, having been overlooked in the first patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes several issues introduced with ZyXEL NBG6716 support:
- Inhomogeneous indent
- Wrong ath10k MAC patching function
- Wrong brackets for pad-to in nand.mk
- Add missing DEVICE_MODEL
- Remove k2t.sh include (copy/paste leftover)
Fixes: 99835e0999 ("ath79: add support for ZyXEL NBG6716")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds ath79 support for Netgear WNR2200.
Router was previously supported by ar71xx target only (8 MiB variant).
Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and
16 MiB for Russia and China markets. Apart from flash size both variants
share the same hardware specification.
Specification
=============
* Description: Netgear WNR2200
* Loader: U-boot
* SOC: Atheros AR7241 (360 MHz)
* RAM: 64 MiB
* Flash: 8 MiB or 16 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 7808 KiB or 16000 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9287)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_generic=y
CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Due to rebase of the base-files split patch after adding support
for the ZyXEL NBG6716, its base-files were added to the generic
subtarget, although the device belongs to the nand subtarget.
This moves the definitions to their proper locations.
Fixes: 0130022bae ("ath79: split base-files into subtargets")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[improve commit message, rebase]
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for the Aerohive HiveAP-121. It was previously
already supported in the ar71xx subtarget.
The following is copied from the commit which added ar71xx support:
Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:
dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds PCI support for the whole ath79 target. Previously,
this was only done in the generic and tiny subtargets.
With the introduction of the HiveAP-121, PCI will be a requirement for
all subtargets, thus moving PCI support to the target configuration.
Signed-off-by: David Bauer <mail@david-bauer.net>
For several devices, wmac MAC address is set from art 0x1002
explicitly by using mtd-mac-address although mtd-cal-data is
pulled from art 0x1000.
With the MAC address in 0x1002, the driver should automatically
use it when reading caldata from 0x1000. Thus, remove the
redundant mtd-mac-address for those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Jeff Kletsky <git-commits@allycomm.com>
Tested-by: Karl Palsson <karlp@etactica.com>
Until upstream commit 6d4cd041f0af("net: phy: at803x: disable delay
only for RGMII mode"), delays were not disabled on driver probe
for the Atheros AR803x PHYs, although the RX delay is enabled on
soft and hard reset.
In addition, the TX delay setting is retained on soft-reset.
This patch disables both delays on config init to align the behavior
with kernel 5.1 and higher. It can be safely dropped with kernel 5.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.
However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space (especially helpful for the tiny devices).
The only script remaining in parent base-files is
/etc/hotplug.d/ieee80211/00-wifi-migration, everything else is
moved/split.
Note that this will increase overall code lines, but reduce code
per subtarget.
base-files ipk size reduction:
master (generic) 49135 B
split (generic) 48533 B (- 0.6 kiB)
split (tiny) 43337 B (- 5.7 kiB)
split (nand) 44423 B (- 4.6 kiB)
Tested on TL-WR1043ND v4 (generic) and TL-WR841N v12 (tiny).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes the remaining IMAGE_SIZE issues in ath79 target.
All devices in target have been checked, so together with
previous patches this target should be "clean" afterwards.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, IMAGE_SIZE is set as follows:
tplink-4m* 3904k 0x3d0000
tplink-8m* 7936k 0x7c0000
tplink-16m* 15872k 0xf80000
However, based on the size of firmware partitions in DTS it should
be:
tplink-4m* 3904k 0x3d0000
tplink-8m* 8000k 0x7d0000
tplink-16m* 16192k 0xfd0000
All (!) 8m*/16m* devices actually follow the latter scheme, which
is also consistent in terms of left free space for other
partitions. Thus, fix it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by:
1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"),
since despite two all subdefinition have different values.
2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k).
3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node
since all have same size (it is defined in parent DTSI ...).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Factory image generated for Netgear WNR1000 v2 has incorrect device
and hardware ID information in header due to missing makefile
variables. This fix adds them to device section.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Attention: Kernel partition size has been enlarged to 4MB.
To switch, you must update to latest ar71xx-nand snapshort and flash the
sysupgrade-4M-Kernel.bin:
zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd -r -e ubi write - firmware; reboot -f
You will end up with a fresh config if you do not inject config into the image.
The NBG6716 may come with 128MB or 256MB NAND. ar71xx was able to use all, but
ath79 can only use the first 128MB. Therefore the complete NAND needs to be
overwritten. If not, the old UBI may make problems and lead to reboot loop.
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6716> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6716>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6716> ATSE NBG6716
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6716> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6716> ATGU
|NBG6716#
Signed-off-by: André Valentin <avalentin@marcant.net>
Rework DEVICE_VENDOR, DEVICE_MODEL, and DEVICE_VARIANT
for the GL-AR300M series on the ath79-generic target.
Changes GL-AR300M-Lite to the current form with
DEVICE_VARIANT := Lite (board name is unchanged)
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The GL-AR750S has an internal header for I2C.
Provide DTS definitions for the i2c-gpio driver.
The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,
Default clock measured ~11.2 ms period, ~89 kHz
The board has well-labeled (unpopulated) headers for serial and I2C
along the front edge of the board (the edge with the LEDs). Looking
from the top, rear of the unit (behind Ethernet jacks)
-------------------------------------------
5G_LED 2G_LED PWR_LED
O O O O O O O
3 S S G T R G
V C D N X X N
3 L A D D
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The GL-AR300M series have an internal header for I2C.
Provide DTS definitions for the i2c-gpio driver.
The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,
Default clock measured ~11.4 ms period, ~88 kHz
The board has two sets of (unpopulated) headers. While facing the
back of the board (looking into the Ethernet jacks), and looking from
the top, the one on the left edge of the baord with four holes is the
I2C header. It appears to be labeled J8 on "GL-AR300M-V1.4.0" boards.
| (Patch antenna)
|
|
| O GND
| O SDA / GPIO 17
| O SCL / GPIO 16
| ⊡ 3V3 (square land)
|
| (Ethernet jacks)
https://docs.gl-inet.com/en/3/hardware/ar300m/#pcb-pinout states
"Note: I2C is not working in some early version of the router."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Previous commit 0cc87b3 "ath79: image: disable sysupgrade images for
routerstations and ja76pf2" doesn't remedy completely the posibility of
bricking the device, since user could try to downgrade with an older
image. Therefore disable sysupgrade code for these boards with a small
note.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This converts leading whitespaces to tabs and removes a double
newline at the end of the file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Several Archer Cxx devices were using board-specific LED names in
ar71xx, which were changed to "tp-link:*" in ath79.
This patch adds migration for them.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Several devices added to LED migration script will just have their
(old) board name converted to tp-link.
By using a variable for this, the amount of code in the migration
script can be reduced and the chance for typos is reduced.
This patch also introduces the marker for beginning of a pattern
"^" to the regex, so the match is more specific.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ar71xx images for the Ubiquiti NanoStation M (XM) devices use
"nanostation-m" as board name, but the ath79 images are only
compatible with the "nano-m" board name, so sysupgrade complains.
By changing this additional supported device, sysupgrade smoothly
upgrades from ar71xx to ath79.
Ref: openwrt#2418
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The code line patching ath9k MAC address for this device contains
a wrong number of arguments including an unset "$mac", which
looks like a typo or copy/paste mistake.
This has been introduced already in the device support commit
745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender").
This patch just removes the "$mac" argument, leaving a formally
valid line. (No on-device test has been performed.)
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch improves ath79 support for Netgear WNR612v2.
Router functionality becomes identical to ar71xx version.
Changes include:
* software control over LAN LEDs via sysfs
* correct MAC addresses for network interfaces
* correct image size in device definition
* dts: 'keys' renamed to 'ath9k-keys'
* dts: 'label-mac-device' set to eth1 (LAN)
* dts: formatting adjustments
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Currently AR724x pinmux for register 0x18040028 controls only JTAG disable bit.
This patch adds new DTS settings to control LAN LEDs and CLKs that allow
full software control over these diodes - exactly the same is done by ar71xx
target in device setup phase for many routers (WNR2000v3 for example).
'switch_led_disable_pins' clears AR724X_GPIO_FUNC_ETH_SWITCH_LED[0-4]_EN bits.
'clks_disable_pins' clears AR724X_GPIO_FUNC_CLK_OBS[1-5]_EN and
AR724X_GPIO_FUNC_GE0_MII_CLK_EN bits. These all should be used together, along
with 'jtag_disable_pins', to allow OS to control all GPIO-connected LEDs and
buttons on device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless
router.
Specification
SoC: Atheros AR1022
RAM: 64 MB DDR2
Flash: 8 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R QCA9882 integrated (connected to PCIe lane)
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled, 5x switch
Buttons: 2x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Known issues
5GHz LED doesn't work
Additional information
When TX line on UART is connected, and board is switched on from power
off state, the DDR memory training may fail.
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), which may or may
not work with introduced images.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The device did not appear to be reachable unless the connection were
forced to 100Mb or lower. Revert to previously working pll-data.
Also fix the phy-mode to represent the actual state needed for ethernet
to function.
Reported-by: Moritz Schreiber <moritz@mosos.de>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[add remark about phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch contains updated driver for Atheros NAND Flash Controller
written originally by Gabor Juhos for ar71xx (aka 'ar934x-nfc').
ath79 version has adapted to work with kernel 4.19 and Device Tree.
It has also been renamed to 'ar934x-nand' to avoid confusion with
Near-Field Communication technology.
Controller is present on Atheros AR934x SoCs and required for accessing
internal flash storage on routers like Netgear WNDR4300.
This port preserves all NAND programming code while moving platform
configuration to Device Tree and replacing some kernel functions marked
for retirement by 4.19.
Suitable definition is included in 'ar934x.dtsi' ('nand@1b000200' section).
Most important changes to ar71xx version are:
* old kernel sections of code removed
* 'bool swap_dma' provided by platform data is now set by boolean DT
property 'qca,nand-swap-dma'
* board-supplied (mach-*.c code) platform data removed - its elements
become either unused, redundant or replaced by DT methods (like reset)
* IRQ is reserved by devm_request_irq() so free_irq() is not needed anymore
* calls to deprecated nand_scan_ident() + nand_scan_tail() function pair
replaced by using recommended nand_scan() with attach_chip() callback
* ECC is set to hardware by default, can be overriden by standard DT
'nand-ecc-*' properties (software Hamming or BCH are other options)
This driver has been successfully tested on Netgear WNDR4300 running
experimental ath79 OpenWrt master branch.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[add reset control]
Signed-off-by: David Bauer <mail@david-bauer.net>
Modify GL-AR300M-Lite and GL-AR300M (NOR):
* Include qca9531_glinet_gl-ar300m.dtsi directly
rather than qca9531_glinet_gl-ar300m-nor.dts
* Remove redundant inclusion of gpio.h and input.h
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).
This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.
This patch adds checksum adjustments for several targets on
ath79 and lantiq.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This corrects the additional boardname for the image metadata to the one
used in ar71xx. The previously present additional entry was never used
on a running system.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
The Unifi AC-LR has identical hardware to the Unifi AC-Lite.
The antenna setup is different according to the vendor,
which explains the thicker enclosure.
Therefore, it is helpful to know the exact device variant,
instead of having "Ubiquiti UniFi-AC-LITE/LR".
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[fix legacy name in commit message; add old boardname to
SUPPORTED_DEVICES]
Signed-off-by: David Bauer <mail@david-bauer.net>
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the COMFAST CF-E313AC, an outdoor wireless
CPE with two Ethernet ports and a 802.11ac radio.
Specifications:
- QCA9531 SoC
- 650/400/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps WAN Ethernet, 48V PoE-in
- 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out
- 1x manual pass-through PoE switch
- 64 MB RAM (DDR2)
- 16 MB FLASH
- QCA9886 2T2R 5 GHz 802.11ac, 23 dBm
- 12 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1)
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while the WAN LED flashes, until it starts flashing faster.
Once in failsafe mode, perform a factory reset as usual.
Alternatively, the U-boot bootloader contains a recovery HTTP server
to upload the firmware. Push the reset button while powering the
device on and keep it pressed for >10 seconds. The device's LEDs will
blink several times and the recovery page will be at
http://192.168.1.1; use it to upload the sysupgrade image.
Note:
Four MAC addresses are stored in the "art" partition (read-only):
- 0x0000: 40:A5:EF:AA:AA:A0
- 0x0006: 40:A5:EF:AA:AA:A2
- 0x1002: 40:A5:EF:AA:AA:A1
- 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data)
The stock firmware assigns MAC addresses to physical and virtual
interfaces in a very particular way:
- eth0 corresponds to the physical Ethernet port labeled as WAN
- eth1 corresponds to the physical Ethernet port labeled as LAN
- eth0 belongs to the bridge interface br-wan
- eth1 belongs to the bridge interface br-lan
- eth0 is assigned the MAC from 0x0 (*:A0)
- eth1 is assigned the MAC from 0x1002 (*:A1)
- br-wan is forced to use the MAC from 0x1002 (*:A1)
- br-lan is forced to use the MAC from 0x0 (*:A0)
- radio0 uses the calibration data from 0x5000 (which contains
a valid MAC address, *:A3). However, it is overwritten by the
one at 0x6 (*:A2)
This commit preserves the LAN/WAN roles of the physical Ethernet
ports (as labeled on the router) and the MAC addresses they expose
by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position
of the eth0/eth1 compared to the stock firmware:
- eth0 corresponds to the physical Ethernet port labeled as LAN
- eth1 corresponds to the physical Ethernet port labeled as WAN
- eth0 belongs to the bridge interface br-lan
- eth1 is the interface at @wan
- eth0 is assigned the MAC from 0x0 (*:A0)
- eth1 is assigned the MAC from 0x1002 (*:A1)
- br-lan inherits the MAC from eth0 (*:A0)
- @wan inherits the MAC from eth1 (*:A1)
- radio0's MAC is overwritten to the one at 0x6
This way, eth0/eth1's positions differ from the stock firmware, but
the weird MAC ressignations in br-lan/br-wan are avoided while the
external behaviour of the router is maintained. Additionally, WAN
port is connected to the PHY gmac, allowing to monitor the link
status (e.g., to restart DHCP negotiation when plugging a cable).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This addresses several issues in the DTS file:
- add diag LED support
- remove unused node names
- fix whitespace issues
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is the result of grepping/searching for several common
whitespace issues like double empty lines, leading spaces, etc.
This patch fixes them for the ath79 target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
The relationship between GMAC0 and GMAC1 and the kernel devices
eth0 and eth1 was reversed for many ath79 devices by commit 8dde11d521
ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi
The GL-AR300M-Lite is a single-port device, with the "LAN" port of the
GL-AR300M board unpopulated and its sole port now referenced as eth1,
as a result of commit 8dde11d521. The device was unreachable on
first boot or fresh config.
By changing ð1 (GMAC1) to an MFD, GMAC0 is able to associate with
the phy and is known by the kernel as "eth0".
Thanks to Chuanhong Guo for the suggestion of "simple-mfd"
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Previously, the board name for the GL-AR300M-Lite was incorrect
in 02_network, resulting in an unintended, fall-through condition
when initializing the network configuration.
While builds prior to commit 8dde11d521 (merged June 5, 2019)
ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi
functioned properly, the error was noted in resolving first-boot
connectivity issues related to the single-phy nature of the device
and the "swap" of eth0 and eth1 related to that commit.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
If chksum_offset is converted by $(($...)) at the beginning, the
check [ -n "$chksum_offset" ] will always return true, as the
conversion yields "0" for an empty argument, and [ -n "0" ] is
true.
With this patch, the variable is not converted before the check,
but only when it's used in dd.
No conversion is done for use in hexdump, as this can deal with
hex value offsets.
Fixes: b133e466b0 ("treewide: convert WiFi caldata size and offset to hexadecimal")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If already included in ucidef_add_switch, you do not have to
additionally set the interface mode in ucidef_set_interfaces_*
functions.
This patch removes/adjusts such redundant cases.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.
Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as
this one is using ath9k keys.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
Add support for the ar71xx supported Netgear WNDR3800CH to ath79.
The device is identical to WNDR3800 except NETGEAR_BOARD_ID.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some ar9344-based devices are using ath9k_patch_fw_mac_crc, which
is meant to generate a checksum, for fixing their ath9k MAC
addresses.
However, those do not have a checksum field, and the calculated
checksum offset would be negative.
This patch will use ath9k_patch_fw_mac function for those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It has been reported that using the sysupgrade-tar image will trigger
"lzma_decode failed error". The RedBoot bootloader always loads data
from flash till block size boundary, so if there's no padding it'll also
load the beginning of rootfs, and it seems that lzma_decoder can't handle
that garbage data. Previously the script creating combined-image
silently padded the kernel and rootfs, but since sysupgrade-tar doesn't,
pad the default kernel image.
Fixes: 900330f ("ath79: image: retire combined-image for Adtran/Bluesocket
devices")
Cc: Brian Gonyer <bgonyer@gmail.com>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This applies alphabetic sorting to devices in image/* files.
For certain cases, this patch deviates from strict sorting, e.g.
to ensure that v10 comes after v9.
While at it, fix an indent and remove some useless empty lines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ar71xx images for the Ubiquiti NanoStation M (XW) devices use
"nanostation-m-xw" as the board name, but the ath79 images are only
compatible with the "nano-m-xw" board name, so sysupgrade complains.
By adding this additional supported device, sysuspgrade smoothly
upgrades from ar71xx to ath79.
Tested on a NanoStation M (XW) running OpenWrt ar71xx r10250-016d1eb.
Ref: https://github.com/openwrt/openwrt/pull/2418
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[removed duplicate DEVICE_VARIANT, removed uneeded nano-m-xw support]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
So far, XW devices have DEVICE_VARIANT defined and XM devices have
no DEVICE_VARIANT set.
This adds DEVICE_VARIANT for XM devices, and moves definitions for
both XM and XW to the common definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds the label MAC address for several devices in
ath79.
Some devices require setting the MAC address in 02_network:
For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices
For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add ath79 support for Archer C59v2, previously supported by ar71xx.
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB
Flash instruction:
- via web UI:
1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
2. Login to router and open the Advanced tab
3. Navigate to System Tools -> Firmware Upgrade
4. Upload firmware using the Manual Upgrade form
- via TFTP:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Keith Maika <keithm@aoeex.com>
The Archer C58/C59 have redundant LED and MAC address definitions
in their DTS files. This moves them to the parent DTSI file.
The patch already accounts for the upcoming Archer C59 v2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This enables using the "eTactica" LED during boot, to indicate failsafe,
and during upgrade, while still leaving the LED alone for normal
operation. This brings the device more in line with how other devices
work, and makes the failsafe functionality easier to use and understand.
Signed-off-by: Karl Palsson <karlp@etactica.com>
The UniFi AC LED mapping is currently off. The blue/white LED are used
as WiFi indicators, while the vendor firmware does not feature WiFI
LEDs.
Instead, the LEDs are used to indicate the devices status. Align the LED
mapping to match the vendor firmware as good as possible.
Signed-off-by: David Bauer <mail@david-bauer.net>
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
That was a result of accidentally running "sed" twice on some files.
Fixes: 5797fe84a3 ("treewide: replace remaining (not working now) $SAVE_CONFIG uses")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG
Fixes: b534ba9611 ("base-files: pass "save_config" option to the "sysupgrade" method")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hardware:
SoC: AR9344
CPU: 560 MHz
Flash: 8 MiB
RAM: 128 MiB
WiFi: Atheros AR9340 2.4GHz 802.11bgn
Atheros AR9300 5GHz 802.11an
Ethernet: AR934X built-in switch, WAN on separate physical interface
USB: 1x 2.0
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wdr3500v1_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[removed stray newline]
Signed-off-by: David Bauer <mail@david-bauer.net>
Because a bug in handling partial erase blocks in 4.19 kernel, using
sysupgrade images will hard brick devices that use RedBoot bootloader
and have "FIS directory" with "RedBoot config" on the same erase block.
Since flashing the devices from bootloader is safe, and to not cause a
situation where external chip programmer or JTAG is needed, disable
sysupgrade images for affected boards while creating kernel.bin and
rootfs.bin for jjPlus JA76PF2 board, which doesn't have factory image.
To set up the JA76PF2 board follow "Installation" instructions in b3a0c97
("ath79: add support for jjPlus JA76PF2") except the part of loading
initramfs image and using sysupgrade image for flashing (point 6 and 7).
Enter following commands to flash the board from bootloader:
fis init
load -r -b 0x80060000 <openwrt_kernel_image_name>
fis create linux
load -r -b %{FREEMEMLO} <openwrt_rootfs_image_name>
fis create rootfs
fis load -l linux
exec -c ""
For RouterStations use TFTP recovery procedure.
Ref: FS#2428
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
When bumping to 4.19 the patch responsible for scaning flash for FIS
partition got left out. Without it devices with RedBoot bootloader using
automatic partitions detection in dts won't boot with the new kernel.
Fixes: 3771176 ("ath79: add support for linux 4.19")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Now that the md5 check is fixed and metadata present, sysupgrade on
ar71xx will complain about device not being supported by the image.
Since the cause is not matching strings for supported devices add them
accordingly.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This target enforces metadata check so add the necessary information. It
was previously removed because md5 sum check. When using these sysupgrade
images on ar71xx target the check would complain about them not matching.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
During review it slipped by that these devices use combined-image which
should never be used for newly added ones. Therefore switch to
sysupgrade-tar generated images introduced in 8f6f260 ("ath79:
routerstation: prepare to use sysupgrade-tar format image"). The
sysupgrade accepts both images for now so no reression should occur.
Cc: Brian Gonyer <bgonyer@gmail.com>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The frequency was filled acording the information from datasheet for
particular chip (Winbond 25Q128BVFG). Unfortunately this led to
coruption and introduced bad blocks on the chip. Reducing the frequency
to commonly used in ath79, made the board more stable and no new bad
blocks were spoted.
Fixes: b3a0c97 ("ath79: add support for jjPlus JA76PF2")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This fixes the previously incorrect phy-mode for the OCEDO Ursus GMAC0.
See 62abbd587d ("ath79: correct various phy-mode properties")
for more details.
Signed-off-by: David Bauer <mail@david-bauer.net>
The button is labelled reboot/restore in documentation, and has always
been used for that. Naming it WPS has always been wrong.
Signed-off-by: Karl Pálsson <karlp@etactica.com>
[matched author to SoB]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
tx_size was just declared above and set to BIT(tx->order)
Use the declaration instead, which could avoid a pointer deref
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
All other instances of this identical declaration fetch the
value directly from the ring_order.
Also do it here.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This patch creates a shared DTSI for the TP-Link devices based
on ar9341 as those share a lot of definitions.
While at it, change from gpio-keys-polled to gpio-keys, remove
unused pll-data and remove some inherited stuff, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: ar9341
- RAM: 32M
- Flash: 4M
- Ethernet: 5x FE ports
- WiFi: ar9341-wmac
Flash instruction:
Upload generated factory firmware on vendor's web interface.
This changes the key assignment compared to ar71xx support of this
device, since of the two keys on the device one is used as combined
Reset/WPS and the second one as WiFi on/off button.
Despite, the reset button required GPIO_ACTIVE_HIGH to work correctly.
Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[redo commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
