The firmware hotplug script tries to read the mac address from a
partition with the name "uboot-env" which does not exist (instead it's
name is uboot_env). This broke calculation of the new checksum (after
patching the mac address) which resulted in ath9k refusing to use the
EEPROM data.
The original error reported by ath9k was:
PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
ath: phy0: Bad EEPROM checksum 0x2523
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:0e.0: Failed to initialize device
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
BCM6362 and BCM3380 seem to share the same PRID. Disable serial output
for them until we can find a way to tell them apart reliably.
Fixes: 8f3cfe4ba2 ("brcm63xx: lzma-loader: add BCM3380 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Setting the clear bit for an interrupt seems to cause interrupts to be
deasserted again immediately. So unset the bit for BCM6318 to allow
subsequent interrupts to still work.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This commit reverts 42f3c1f ("arc770: fix broken upstream change")
and simultaneously adds back-ported fix from Linus' tree:
a524c218bc94 ("ARC: [arcompact] brown paper bag bug in unaligned
access delay slot fixup").
Note mentioned patch will appear in stable trees soon as well so
IMHO there's not much sense in adding this separate patch in lede/master branch.
As well as we will get rid of it here in 17.01 once we bump 4.4 kernel here
later down the line.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Jo-Philipp Wich <jo@mein.io>
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.
Signed-off-by: Claudio Leite <leitec@gmail.com>
It's needed for macaddr_add.
Fixes: 5ed23223fd ("bcm53xx: set WAN MAC address to don't share one with LAN interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.
Runtime-tested on ar71xx, octeon, ramips and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit d2c4041f02)
Conflicts:
include/kernel-version.mk
target/linux/ramips/patches-4.4/997-ralink-Introduce-fw_passed_dtb-to-arch-mips-ralink.patch
Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64.
.44 has been run-tested on the 17.01 branch here on ar71xx and mt7621.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
(cherry picked from commit 20996edd68)
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Conflicts:
target/linux/ar71xx/patches-4.4/920-usb-chipidea-AR933x-platform-support.patch
target/linux/ar71xx/patches-4.4/930-chipidea-pullup.patch
It just makes code consistent. This trivial change may be a 17.01
candidate to provide simpler backporting experience.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is a pure rename without any changes. It makes maintaining bgmac
simpler and will hopefully make adding new kernel a bit easier.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.
Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.
Fixes: FS#451
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
After analyzing numerous NVRAMs and vendor firmwares it seems the base
MAC address is used for LAN interface. WAN interface has different one
which sometimes is set directly in NVRAM and sometines needs to be
calculated.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The setting mmc-ddr-1_8v in the platform dts leads to read errors. The
device is unusable and system reboots in a loop. Because NBG6817 is the
only mmc device, I removed it in base dts.
The second change removes settings now present in base dts.
The third change references was a wrong conversion of constants in the switch settings.
Switch now initializes again.
Signed-off-by: André Valentin <avalentin@marcant.net>
All mvebu boards have three USB LEDs. The first one is used for the
USB1 port.
There are two LEDs related to the second USB port. The top (bar) LED
gets bright in case any USB device is connected to the second USB port.
If the connected device is an USB 3 (SuperSpeed) device, the small dot
LED bellow the "bar" LED gets also bright.
While at it, use a name for the USB LEDs that matches the names printed
on the case.
Fixes: FS#423, FS#425
Signed-off-by: Kabuli Chana <newtownbuild@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This change adds the sp5100_tco driver as a kernel module for the x86
target. Specifically, this can be used by the PCEngines APU2/APU3. The
reason for having this as a kernel module is to allow users to
load/unload it on demand, as the I2C interface on the APU2/APU3 will not
work while this module is loaded. More info can be found on GitHub at
https://github.com/riptidewave93/LEDE-APU2/pull/5#issuecomment-255667736
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This adds the following patches to the x86 target:
sp5100_tco: Add AMD Mullins platform support
sp5100_tco: Add AMD Carrizo platform support
sp5100_tco: fix the device check for SB800 and later chipsets
watchdog: sp5100_tco: properly check for new register layouts
With these added, the sp5100_tco driver can then be used on newer AMD
platforms, such as the PCEngines APU2/APU3 boards.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
erlite mtdparts exposes boot0, boot1 and eeprom regions
as read/write.
this patch adds readonly flags, so these regions can't be
modified. same as it is already for ER profile.
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.
This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.
Signed-off-by: Zhang Jingye <934526987@qq.com>
Running ar8327_get_arl_entry() early after boot leads to MDIO related system
lockups on several devices using this driver.
Since dumping the ARL table contens is an optional, uncritical feature, simply
disable the code for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We override default Ethernet interface with eth0 which often uses random
MAC due to missing proper NVRAM entry. Fix this by manually assigning
MAC in the config.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The soft_config partition must be writeable for rbcfg to be able to
enact changes to the routerboot configuration.
The read-only flag was a mistake in the initial patch. Removing it
brings mach-rb941.c in line with all other RB platforms.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Mikrotik RB411U has only one ethernet port - eth0. This patch allows to create
correct config with one lan section.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Add full support for Mikrotik RB-941-2nD (hAP lite)
Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.
There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB
Signed-off-by: Felix Fietkau <nbd@nbd.name>
