r40587 added some kernel config options, on which these two ones depend.
This fixes the build of the buildbots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40588
The 7Links PX-4885 is a small battery-powered wireless router.
It is based on a RT5350F WiSoC and features one ethernet port and one
USB port. It is a Hame MPR-A1 clone, except it has different GPIOs,
a different battery and more RAM (32 MB).
This patch adds a profile for this board, the corresponding device tree
file and the adequate base-files changes (incl. sysupgrade).
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
SVN-Revision: 40554
This patch adds port status information and MIB counters to the ADM6996
switch driver.
The driver supports also the older ADM6996L-variant, but I'm not able to
test this patch on that chip. According to the datasheet the same
registers exist there as well, so I think it should work, but any
feedback is appreciated.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40542
The total ethernet frame length should be written to the hardware
register LTQ_ETOP_IGPLEN instead of just the value of the MTU. This
patch fixes network issues on various Danube boards, especially when
VLAN tagging is enabled.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40541
The canbus package was recently changed to a more active project. This patch
updates the default package names to include the same functionality as before.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40531
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40509
Add a patch for the at803x phy driver, in order to be able
to configure some register settings via platform data.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40507
Forgotten patch to fix ethernet for rt2880.
Based on previously submitted patch from Claudio.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40504
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40500
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40499
This patch moves ARV7519RW definitions to VR9 section from the AR9 section and removes a whitespace that breaks jffs2 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40495
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40481
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40479
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40478
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40477
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40475
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40474
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40473
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40471
According to Christophe, the kernel boots on the Soekris net5501
board.
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40468
Move the comments out from the shell script to fix build
breakage introduced in r40464.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40466
