Fixes two high-severity vulnerabilities:
- CVE-2022-25640: A TLS v1.3 server who requires mutual authentication
can be bypassed. If a malicious client does not send the
certificate_verify message a client can connect without presenting a
certificate even if the server requires one.
- CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS
v1.3 server can have its certificate heck bypassed. If the sig_algo in
the certificate_verify message is different than the certificate
message checking may be bypassed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This updates mac80211 to version 5.15.33-1 which is based on kernel
5.15.33.
The removed patches were applied upstream.
This new release contains many fixes which were merged into the upstream
Linux kernel.
This also contains the following new drivers which are needed for ath11k:
* net/qrtr/
* drivers/bus/mhi/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
As anyway only the default is called now we can as well also just remove
the override for Build/Configure.
Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix compilation and usage under kernel 5.15 for the mwlwifi driver.
For detailed description of changes, check individual patches.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
Duncan Roe (5):
nlmsg: Fix a missing doxygen section trailer
build: doc: "make" builds & installs a full set of man pages
build: doc: get rid of the need for manual updating of Makefile
build: If doxygen is not available, be sure to report "doxygen: no" to ./configure
src: doc: Fix messed-up Netlink message batch diagram
Fernando Fernandez Mancera (1):
src: fix doxygen function documentation
Florian Westphal (1):
libmnl: zero attribute padding
Guillaume Nault (1):
callback: mark cb_ctl_array 'const' in mnl_cb_run2()
Kylie McClain (1):
examples: nfct-daemon: Fix test building on musl libc
Laura Garcia Liebana (4):
examples: add arp cache dump example
examples: fix neigh max attributes
examples: fix print line format
examples: reduce LOCs during neigh attributes validation
Pablo Neira Ayuso (3):
doxygen: remove EXPORT_SYMBOL from the output
include: add MNL_SOCKET_DUMP_SIZE definition
build: libmnl 1.0.5 release
Petr Vorel (1):
examples: Add rtnl-addr-add.c
Stephen Hemminger (1):
examples: rtnl-addr-dump: fix typo
igo95862 (1):
doxygen: Fixed link to the git source tree on the website.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
c63f193 bump version to 1.0.2
3cffa84 libnfnetlink: Check getsockname() return code
90ba679 include: Silence gcc warning in linux_list.h
bb4f6c8 Make it clear that this library is deprecated
e46569c Minimally resurrect doxygen documentation
5087de4 libnfnetlink: hide private symbols
62ca426 autogen: don't convert __u16 to u_int16_t
efa1d8e src: Use stdint types everywhere
7a1a07c include: Sync with kernel headers
7633f0c libnfnetlink: initialize attribute padding to resolve valgrind warnings
94b68f3 configure: uclinux is also linux
617fe82 src: get source code license header in sync with current licensing terms
97a3960 build: resolve automake-1.12 warnings
Removed the patch 100-missing_include.patch, libnfnetlink compiles fine
with musl without this patch.
Signed-off-by: Nick Hainke <vincent@systemli.org>
bh_event_add_var can be called by multiple threads concurrently,
so it shall not use a static char buffer
Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com>
92f5e18675bf interface: fix ifname present check in interface status
ef82defaae26 ubus: add active devices to bridger blacklist
Signed-off-by: Felix Fietkau <nbd@nbd.name>
33f1e0b treewide: move json-c compat shims into internal header file
e0e9431 vm: move unhandled exception reporting out of `uc_vm_execute_chunk()`
2b59140 vm: fix callframe double free on unhanded exceptions
7d7e950 main: abort when failing to load a preload library
1032a67 lib: let `json()` accept input objects implementing `read()` method
5ee68d5 fs: implement `fs.readfile()` and `fs.writefile()`
df6b861 ci: debian: change path before attempting to invoke Git operations
dfaf05a ci: debian: automatically update changelog from Git tag
34f3c45 ci: fix YAML syntax of Debian workflow
e956bcf fs: fix off-by-one in fs.dirname() function
6fc4b6c .gitignore: fix overmatching patterns, blacklist cram .venv
7c2e082 build: remove legacy json-c check
77942af build: add polyfills for older libjson-c versions
0b4aaa3 CI: build Debian package
f404285 debian: Add package definition
a37f654 types: fix escape sequence encoding of high byte values in JSON strings
aae5312 Update README.md
8134e25 build: fix symlink install target
87c7296 treewide: replace some leftover "utpl" occurrences, update .gitignore
7d27ad5 build: only stage ucc symlink if compile support is enabled
171402f lib: add date and time related functions
8b5dc60 lib: provide API function to obtain stdlib function implementations
eb0d2f1 main: turn ucode into multicall executable
28ee7e1 uloop: add support for tasks
753dea9 CI: build on macOS
668c5c0 lib: add argument position support (`%m$`) to `sprintf()` and `printf()`
ab46fdf treewide: remove legacy json-c include directives
b8f49b1 tests: 21_regex_literals: generalize syntax error test case
fd2e5e7 tests: 16_sort: fix logic flaw exposed on OS X
2c71bf2 tests: run_tests.sh: pass dummy value to `-T` flag
55c4a90 lib: disallow zero padding for %s formats
0d05cb5 tests: run_tests.sh: use greadlink if available
271e520 resolv: make OS X compatible
d13c320 fs: avoid Linux specific sys/sysmacros.h include on OS X
33397a3 uloop: use execvp() on OS X
bafdc8f lib: add naive sigtimedwait() stub for OS X
ada1585 build: consolidate CMakeLists.txt and cover OS X deviations
befbb69 include: add OS X compatible endian.h header
49838a8 include: rename include guards to avoid clashes with system headers
91f65de nl80211: add missing attributes and correct some attribute flags
b4a1fd5 lib: adjust require(), render() and include() raw mode semantics
4618807 main: rework CLI frontend
73dcd78 lib: fix potential integer underflow on empty render output
c402551 vm: fix crash on object literals with non-string computed properties
efe8a02 syntax: support add new operators
078d686 ubus: add event support
6c66c83 ubus: refactor error and argument handling
1cb04f9 ubus: add object publishing, notify and subscribe support
0e85974 uloop: clear errno before integer conversion attempts
05bd7ed types: treat resource type prototypes as GC roots
a2a26ca lib: introduce uloop binding
6b6d01f vm: release this context on exception in managed method call
1af23a9 tests: fix proto() testcase
4ce69a8 fs: implement access(), mkstemp(), file.flush() and proc.flush()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add a ubus method to request link-measurements from connected STAs.
In addition to the STAs address, the used and maximum transmit power can
be provided by the external process for the link-measurement. If they
are not provided, 0 is used as the default value.
Signed-off-by: David Bauer <mail@david-bauer.net>
5beb87716e70 mt76: dma: add wrapper macro for accessing queue registers
e0bc736d5617 mt76: add support for overriding the device used for DMA mapping
b8c842daa081 mt76: make number of tokens configurable dynamically
87a962e0608f mt76: mt7915: add Wireless Ethernet Dispatch support
2accb74e6be3 mt76: mt7915: fix using null pointer when wfsys on
e5227f2f3120 mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
ec0e9f4da32f mt76: mt7915: fix possible uninitialized pointer dereference in mt7986_wmac_gpio_setup
5a87be892ba7 mt76: mt7915: fix possible NULL pointer dereference in mt7915_mac_fill_rx_vector
fe441e5d3dcf mt76: mt7915: do not pass data pointer to mt7915_mcu_muru_debug_set
f3ddfe886283 mt76: mt7915: report rx mode value in mt7915_mac_fill_rx_rate
2a0d370cb5fe mt76: mt7915: use 0xff to initialize bitrate_mask in mt7915_init_bitrate_mask
506bb0605e3e mt76: mt7921: Add AP mode support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Two patches were removed because of the changes introduced in upstream:
1. 110-mx6cuboxi-mmc-fallback.patch
Looks like similar changes were introduced in 6c3fbf3e456c ("mx6cuboxi:
customize board_boot_order to access eMMC").
2. 111-mx6cuboxi_defconfig-force-mmc-boot.patch
The 'CONFIG_SPL_FORCE_MMC_BOOT' was removed in 15aec318ef03 ("Revert
"imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon
mode").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The host-build of libselinux requires libsepol/host.
Add the libsepol/host to HOST_BUILD_DEPENDS to allow build on hosts
which don't have libsepol installed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Problem exist when dnsmasq is exclusively bind to particular interface.
After reconfiguring or restarting this interface, its index changes, but
dnsmasq uses the old one. When this problem occurs, dnsmasq does not
listen on the correct interface so DHCP does not work, and clients do not
get an IP address. Procd netdev param can be added to restart dnsmasq when
the interface index is changed.
Signed-off-by: Valentyn Datsko <valikk.d@gmail.com>
[combined into a single &&-connected statement]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This package uses BPF to create a fast path which improves bridging performance
by bypassing the bridge layer. It also supports creating tc offload rules for
hardware that supports it.
Hardware offload support can be used with MT7622 + MT7915 once it is merged
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Replace the tc-full dependency with tc + libnl-tiny
1cd5e12eecdc loader/interface: attach bpf program directly using netlink
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MHI WWAN CTRL allows QCOM-based PCIe modems to expose different modem
control protocols/ports to userspace, including AT, MBIM, QMI, DIAG
and FIREHOSE. These protocols can be accessed directly from userspace
(e.g. AT commands) or via libraries/tools (e.g. libmbim, libqmi, libqcdm)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This driver provides MHI PCI controller driver for devices
such as Qualcomm SDX55 based PCIe modems
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Previously commit openwrt/packages@3abb7cb ("lvm2: Added script and updated Makefile[...]")
couldn't actually work and allow rootfs_data to be stored on a LVM2 as
the necessary kernel modules had not been loaded at this point.
Fix this by loading device-mapper modules early at boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).
Backport upstream commit for its effect on the number of connections per
hashtable bucket.
Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
A Python script containing an unreproducible path is copied by default.
Remove it before generating the package.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The first argument for snprintf is the buffer and the 2. one is the
size. Fix the order. This broke the lock application.
Fixes: 34567750db ("busybox: fix busybox lock applet pidstr buffer overflow")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes following issue:
Package kmod-drm-imx-ldb is missing dependencies for the following libraries:
drm_dp_aux_bus.ko
Introduced upstream in commit aeb33699fc2c ("drm: Introduce the DP AUX
bus") in kernel version 5.15.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following issue:
Package kmod-drm is missing dependencies for the following libraries:
fb.ko
Introduced upstream in commit f611b1e7624c ("drm: Avoid circular
dependencies for CONFIG_FB") in 5.14.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Kernel setting `/proc/sys/kernel/pid_max` can be set up to 4194304 (7
digits) which will cause buffer overflow in busbox lock patch, this
often happens when running in a rootfs container environment.
This commit enlarges `pidstr` to 12 bytes to ensure a sufficient buffer
for pid number and an additional char '\n'.
Signed-off-by: Qichao Zhang <njuzhangqichao@gmail.com>
Fixes following build issues:
Package kmod-r8169 is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-ixgbe is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-amd-xgbe is missing dependencies for the following libraries:
mdio_devres.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The RNG can't actually be seeded from a shell script, due to the
reliance on ioctls. For this reason, the seedrng project provides a
basic script meant to be copy and pasted into projects like OpenWRT
and tweaked as needed: <https://git.zx2c4.com/seedrng/about/>.
This commit imports it into the urandom-seed package and wires up the
init scripts to call it. This also is a significant improvement over the
current init script, which does not robustly handle cleaning up of seeds
and syncing to prevent reuse. Additionally, the existing script creates
a new seed immediately after writing an old one, which means that the
amount of entropy might actually regress, due to failing to credit the
old seed.
Closes: https://github.com/openwrt/openwrt/issues/9570
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed missing INSTALL_DIR]
List of changes since previous release from 2018 is quite long:
* Fix crc32.c to compile local functions only if used.
* Check for cc masquerading as gcc or clang in configure.
* Remove destructive aspects of make distclean.
* Separate out address sanitizing from warnings in configure.
* Eliminate use of ULL constants.
* Add fallthrough comments for gcc.
* Clean up minizip to reduce warnings for testing.
* Fix unztell64() in minizip to work past 4GB. (Daniël Hörchner)
* minizip warning fix if MAXU32 already defined. (gvollant)
* Replace black/white with allow/block. (theresa-m)
* Fix indentation in minizip's zip.c.
* Improve portability of contrib/minizip.
* Correct typo in blast.c.
* Change macro name in inflate.c to avoid collision in VxWorks.
* Clarify gz* function interfaces, referring to parameter names.
* Fix error in comment on the polynomial representation of a byte.
* Fix memory leak on error in gzlog.c.
* Avoid adding empty gzip member after gzflush with Z_FINISH.
* Explicitly note that the 32-bit check values are 32 bits.
* Use ARM crc32 instructions if the ARM architecture has them.
* Add use of the ARMv8 crc32 instructions when requested.
* Correct comment in crc32.c.
* Don't bother computing check value after successful inflateSync().
* Use atomic test and set, if available, for dynamic CRC tables.
* Speed up software CRC-32 computation by a factor of 1.5 to 3.
* Add crc32_combine_gen() and crc32_combine_op() for fast combines.
* Add tables for crc32_combine(), to speed it up by a factor of 200.
* Fix the zran.c example to work on a multiple-member gzip file.
* Add gznorm.c example, which normalizes gzip files.
* Show all the codes for the maximum tables size in enough.c.
* Clarify that prefix codes are counted in enough.c.
* Use inline function instead of macro for index in enough.c.
* Clean up code style in enough.c, update version.
* Use a macro for the printf format of big_t in enough.c.
* Use a structure to make globals in enough.c evident.
* Assure that the number of bits for deflatePrime() is valid.
* Fix a bug that can crash deflate on some input when using Z_FIXED.
* Correct the initialization requirements for deflateInit2().
* Emphasize the need to continue decompressing gzip members.
* Add legal disclaimer to README.
* Fix deflateEnd() to not report an error at start of raw deflate.
* Remove old assembler code in which bugs have manifested.
* Make the names in functions declarations identical to definitions.
* Avoid an undefined behavior of memcpy() in _tr_stored_block().
* Avoid undefined behaviors of memcpy() in gz*printf().
* Avoid an undefined behavior of memcpy() in gzappend().
* Avoid the use of ptrdiff_t.
* Handle case where inflateSync used when header never processed.
* Don't compute check value for raw inflate if asked to validate.
* Add address checking in clang to -w option of configure.
* Return an error if the gzputs string length can't fit in an int.
* Small speedup to inflate [psumbera].
* Update use of errno for newer Windows CE versions.
* Avoid some conversion warnings in gzread.c and gzwrite.c.
* Have Makefile return non-zero error code on test failure.
* Avoid a conversion error in gzseek when off_t type too small.
* Fix CLEAR_HASH macro to be usable as a single statement.
* Fix bug when window full in deflate_stored().
* Limit hash table inserts after switch from stored deflate.
* Permit a deflateParams() parameter change as soon as possible.
* Cygwin does not have _wopen(), so do not create gzopen_w() there.
Removed 006-fix-compressor-crash-on-certain-inputs.patch which was
hotfix for CVE-2018-25032 and is now included in this release.
This release is not available on @SF (yet?) so the sources are now
pulled from GitHub.
Fixes: CVE-2018-25032
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The inclusion of the kmod-leds-uleds into the userspace
nu801 package causes a circular dependency inside the
buildsystem... which causes it to be picked regardless
of other DEPENDS values.
In case of the mx100, this could be solved by moving the
kmod-leds-uled dependency to the kmod-meraki-mx100.
Bonus: drop @!LINUX_5_4 from kmod-meraki-mx100
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Chen Minqiang reported that he has troubles downloading nu801.
His logs showed the followin TLS Handshake failure.
|Checking out files from the git repository...
|Cloning into 'nu801-d9942c0c'...
|fatal: unable to access 'https://github.com/chunkeey/nu801.git/':
| gnutls_handshake() failed: The TLS connection was non-properly terminated.
|Makefile:39: recipe for target '[...]/dl/nu801-d9942c0c.tar.xz' failed
This can be fixed by providing a PKG_MIRROR_HASH. The download
scripts will now be able to pull the source from OpenWrt's source
archive, which should be available through HTTP.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
intl is not included in libc, disable it as is done with the target
package.
argp is also not included. Add build depends for argp-standalone.
fts is also not included. Add build depends for musl-fts.
Disable shared libraries to avoid having to manually add rpath.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Getting rid of shared libraries for hostpkg avoids having to use rpath
hacks to find the library. It also fixes compilation with host glib2
binaries.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Avoids having to add rpath to the various packages using it. Also add
PIC to fix compilation as static libraries do not use PIC by default.
Fixes: 1fb099341e ("musl-fts: add host build")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Add new module require in 5.15
- Changes in block module
- Changes in netfilter module (log module unified)
- Changes in fs module (mainly new depends for cifs and new ntfs3 module)
- Changes in lib add shared lib now used by more than 1 kmod
- Changes in crypto, dropped one crypto algo added arm crypto accellerator
- Changes in other, add zram default compressor choice and missing lib
by tpm module
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
This reverts commit 80b7a8a7f5.
Now that 5.10 is the default kernel for all platforms, we can
bring back the NU801 userspace driver for platforms that rely
on it. Currently it's used on the MX100 x86_64 target, but
other Meraki platforms use this controller.
Note that we also now change how we load nu801. The way we did
this previously with procd worked, but it meant it didn't load
until everything was up and working.
To fix this, let's call nu801 from boot and re-trigger the
preinit blink sequence. Since nu801 runs as a daemon this is
now something we can do.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(removed empty line, currently only MX100 uses it so: @TARGET_x86)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
See firmware-utils.git commits [1], which implemented the cros-vbutil
verified-boot payload-packing tool, and extended ptgen for the CrOS
kernel partition type. With these, it's now possible to package kernel +
rootfs to make disk images that can boot a Chrome OS-based system (e.g.,
Chromebooks, or even a few AP models).
Regarding PARTUUID= changes: Chromium bootloaders work well with a
partition number offset (i.e., relative to the kernel partition), so
we'll be using a slightly different root UUID line.
NB: I've made this support specific to ip40xx for now, because I only
plan to support an IPQ4019-based AP that uses a Chromium-based
bootloader, but this image format can be used for essentially any
Chromebook, as well as the Google OnHub, a prior Chromium-based AP using
an IPQ8064 chipset.
[1]
ptgen: add Chromium OS kernel partition support
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=6c95945b5de973026dc6f52eb088d0943efa96bb
cros-vbutil: add Chrome OS vboot kernel-signing utility
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=8e7274e02fdc6f2cb61b415d6e5b2e1c7e977aa1
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
From a manufacturer's image (version R89-13729.57.27), with appopriate
',variant=' appended to the board names:
$ .../qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder \
-i ./board-google_wifi.qca4019
FileSize: 48596
FileCRC32: 3966df5d
FileMD5: d54161b0fb9e93691c4272649c37535a
BoardNames[0]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_GALE'
BoardLength[0]: 12064
BoardCRC32[0]: e117f336
BoardMD5[0]: ea35e78c88a8571201da8b75edc9b881
BoardNames[1]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_GALE'
BoardLength[1]: 12064
BoardCRC32[1]: 6c751ec9
BoardMD5[1]: 44cbc4ca6cb7141ba4249615f7065582
BoardNames[2]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_BREEZE'
BoardLength[2]: 12064
BoardCRC32[2]: 24fba117
BoardMD5[2]: b4ac055b3ab67d5a6f5607a96af39a1f
BoardNames[3]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_BREEZE'
BoardLength[3]: 12064
BoardCRC32[3]: a3e16b2a
BoardMD5[3]: 8b26cb285032314247304114b8ac50e7
Naming follows existing Google projects included in upstream board-2.bin
-- GO(ogle) prefix, an underscore (_), and the project code name, all in
caps.
Note that I only tested the "gale" model; the "breeze" model is a later
revision (same marketing name) with very small hardware changes but
otherwise using the same firmware image.
Submitted upstream here:
ath10k-firmware: QCA4019: hw1.0: Add Google Wifi BDFs
http://lists.infradead.org/pipermail/ath10k/2022-March/013465.htmlhttps://lore.kernel.org/ath10k/YjaNGW252Ls%2FyDw8@localhost/
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fixes compilation under musl based distros like Alpine Linux.
Also add pcre/host as a build dependency as it's needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Some configure scripts look for msgfmt and gmsgfmt. As we don't install
the latter, configure might pick up one from staging_dir/hostpkg, and
the other from the host:
checking for msgfmt... /home/stijn/Development/OpenWrt/openwrt/staging_dir/hostpkg/bin/msgfmt
checking for gmsgfmt... /usr/bin/gmsgfmt
This could potentially lead to hard to debug undefined behaviour.
Install a symlink in the host install phase to avoid this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Evaluating the return value of 'json_load' didn't work in the
intended way resulting in PIN status no longer being read on modems
where --get-pin-status doesn't fail.
Fix this by trying --get-pin-status first and checking if pin1_status
field exists in JSON, and if it doesn't try again with
--uim-get-sim-state.
Fixes: #9501
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tavis has just reported, that he was recently trying to track down a
reproducible crash in a compressor. Believe it or not, it really was a
bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs.
Tavis has reported it upstream, but it turns out the issue has been
public since 2018, but the patch never made it into a release. As far as
he knows, nobody ever assigned it a CVE.
Suggested-by: Tavis Ormandy <taviso@gmail.com>
References: https://www.openwall.com/lists/oss-security/2022/03/24/1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
engine.mk is supposed to be included by engine packages, but it will not
be present in the SDK in the same place as in the main repository.
Move it to include/openssl-engine.mk to avoid this.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
860ca90 odhcpd: Support for Option NTP and SNTP
83e14f4 router: advertise removed addresses as invalid in 3 consecutive RAs
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Albeit a separate crypto module, lzo-rle uses the same kernel library as lzo.
Crypto API users (zram, for example) expect both lzo and lzo-rle to be
available, so let's include lzo-rle (about 5.5 kiB) in the lib-lzo package.
Based on e9hack's original patch: https://patchwork.ozlabs.org/project/openwrt/patch/541cbfbd-76f2-59b3-a867-47b6f0fc7da9@gmail.com/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Store selected boot configuration in '/chosen' node in device tree, so
it can be accessed by Linux (and used for fine-tuning the FIT partition
parser).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Shuttle KD20 has NAND flash with 0x20000 (128KiB) erase blocks.
Correctly set that in uboot-envtools as well to allow writing to the
bootloader environment using fw_setenv.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
391a9fbd5ace dns: fix parsing vlan encapsulated protocol
6aeeddbc91ad interface: extend dns filters to cover vlan tagged traffic as well
1ab53d4ca601 bpf: return TC_ACT_UNSPEC to allow other filters to proceed
ca21e729af23 interface: switch to using clsact for filters
5d158f6b3c15 interface: run ingress bpf filter on main device ingress instead of ifb egress
bdfcb11847ce interface: fix duplicated dns filter line
b97405aa632a Revert "ubus: remove dnsmasq subscriber"
8fbaf39dbc95 interface: rework adding/removing filters, do not delete clsact
d7ba5804eae4 interface: replace open-coded ifb-dns string with QOSIFY_DNS_IFNAME
91cf440db9e2 loader: fix use of deprecated functions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
v2022.01 has a regression that broke eMMC usage on most if not all Armada
SoC-s, thus breaking boards like uDPU which use eMMC for storage.
Fix it by backporting a recent upstream patch.
Fixes: 782d4c8306 ("uboot-mvebu: update to version 2022.01")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Some users noticed repeated resyncs at random intervals, which go away
when the MEI driver is configured to use polling instead of interrupts.
Debugging shows that this seems to be caused by concurrent calls to
MEI_ReadMailbox (in the interrupt handler) and MEI_WriteMailbox. This
appears to be mostly triggered when there is an interrupt for vectoring
error reports.
In polling mode, calls to MEI_ReadMailbox are protected by the same
semaphore as is used in MEI_WriteMailbox. When interrupts are used,
MEI_WriteMailbox appears to rely on MEI_DisableDeviceInt and
MEI_EnableDeviceInt to provide mutual exclusion with the interrupt
handler. These functions mask/unmask interrupts, and there is an
additional check of the mask in the interrupt handler itself. However,
this is not sufficient on systems with SMP, as the interrupt handler
may be running in parallel, and could already be past the interrupt
mask check at this point.
This adds a lock to the interrupt handler, and also acquires this lock
in MEI_DisableDeviceInt. This should make sure that after a call to
MEI_DisableDeviceInt the interrupt is masked, and the interrupt handler
is either not running, has alread finished its work, or is still before
the interrupt mask check, and is thus going to detect the change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This tells the modem about the WAN MAC address, which is used as source
address for vectoring error reports that are generated by the firmware.
It needs to be set early, as the MEI driver only actually writes the
value to the modem when is in reset state (i.e. the firmware has been
loaded, but connection has not started yet).
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This re-enables the vectoring error sample callback and adds a
dependency to the corresponding driver.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
In order to calculate the required pre-distortion for downstream
vectoring, the vectoring control entity (VCE) at the carrier office
needs error samples from the modem. On Lantiq VR9 modems, error reports
are generated by the firmware, but need to be multiplexed into the data
stream by the driver on the main processor when L2 encapsulation is
selected by the VCE.
This driver provides the necessary callback function, which is called by
the MEI driver after receiving an error report from the firmware.
Originally, it is part of the Lantiq PPA driver, but after a few changes
it also works with the PTM driver used in OpenWrt. The direct call to
ndo_start_xmit needs to be replaced, as the PTM driver relies on locks
from the kernel. Instead dev_queue_xmit is used, which is called from a
work queue, as it is not safe to call from an interrupt handler.
Additional changes include fixes to support recent kernel versions and
a change of the used interface from ptm0 to dsl0.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
A service managed by procd does have a json object with usefull information.
This information could by dumped with the following command.
ubus call service list "{ 'verbose':true, 'name': '<service-name>)'". }"
This line is long and complicated to enter. This commit adds a wrapper
call to the procd service section tool to simplify the input and get the
output faster.
We could now enter the command /etc/initd/<service> info to get the info
faster.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The service command belongs to the procd and does not belong in the
shinit. In the course of the move, the script was also checked with
shellcheck and cleaned up.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add a patch to add some missing init_extensions{a,b}() calls
Package lib{arp,eb}t_*.so
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
This allows to install ip6tables-nft without iptables-nft
This prepare the addition of {arp,eb}tables-nft
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
This prepare the introduction of ebtables-nft.
Add PROVIDES so dependencies are not broken,
use ALTERNATIVES.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
This prepare the introduction of arptables-nft.
Add PROVIDES so dependencies are not broken,
use ALTERNATIVES.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
- Binary files were renamed to cyfmac from brcmfmac, but the files needs
to be on the router with the previous naming
[ 6.656165] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 6.665182] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2
[ 6.674928] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.bin
- Cypress were acquired by Infineon Technologies
Thus change the project URL and switch to download files from their
GitHub repository. This is much better than the previous solution, which
requires finding new threads on their community forum about new driver
updates, and it will be necessary to change the URL each time.
Unfortunately, it seems that there is not published changelog, but
according to this forum thread [1], be careful by opening the link from
solution since it contains ending bracket ), it brings fixes for various
security vulnerabilities, which were fixed in 7_45_234.
Fixes:
- FragAttacks
- Kr00k
Also add LICENSE file
Run tested on Seeedstudio router powered by Raspberry Pi 4 CM with
package cypress-firmware-43455-sdio.
Before:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.895050] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:20:01 version 7.45.206 (r725000 CY) FWID 01-febaba43
After:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.829805] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Apr 15 2021 03:03:20 version 7.45.234 (4ca95bb CY) FWID 01-996384e2
[1] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/Outdated-brcmfmac-firmware-for-Raspberry-Pi-4-in-OpenWrt-21-02-1/m-p/331593#M2269
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
drop the use of LIB_SUFFIX
Fixes: 00cbf6f6ab ("bpftools: update to standalone bpftools + libbpf, use the latest version")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rootfs overlays get created at a ROOTDEV_OVERLAY_ALIGN (64KiB)
alignment after the rootfs, but emmc_do_upgrade() is assuming
it comes at the very next 512-byte sector.
Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(move spaces around, mention fstools' libtoolfs)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is a bugfix release. Changelog:
*) Fixed a bug in the BN_mod_sqrt() function that can cause it to loop
forever for non-prime moduli. (CVE-2022-0778)
*) Add ciphersuites based on DHE_PSK (RFC 4279) and ECDHE_PSK
(RFC 5489) to the list of ciphersuites providing Perfect Forward
Secrecy as required by SECLEVEL >= 3.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
378b638c70c0 mt76: mt7915: fix unused variable with testmode disabled
4f4309542862 mt76: mt7915: only use u32_get_bits with constant value
de06d828a0bf mt76: mt7921: fix injected MPDU transmission to not use HW A-MSDU
c007ba3ec7a9 mt76: mt7915: simplify conditional
64c74dc93f68 mt76: fix dfs state issue with 160 MHz channels
d3471b0d92c1 mt76: mt7615: honor ret from mt7615_mcu_restart in mt7663u_mcu_init
f4c87b32e0e9 mt76: mt7663u: introduce mt7663u_mcu_power_on routine
82de5987af54 mt76: mt7921: fix up the monitor mode
c501df4086e1 mt76: mt7921: use mt76_hw instead of open coding it
594ee03d5a11 mt76: mt7915: fix DFS no radar detection event
d8d2b383a241 mt76: split single ldpc cap bit into bits
0f336fba20fe mt76: mt7921: make mt7921_init_tx_queues static
00a066ce9914 mt76: mt7921: fix xmit-queue dump for usb and sdio
d6d2479568b2 mt76: mt7921: fix mt7921_queues_acq implementation
d17b74420199 mt76: fix monitor mode crash with sdio driver
c374559eae6f mt76: mt7915: allow beaconing on all chains
b219af63b9ce mt76: connac: add 6 GHz support for wtbl and starec configuration
630384cb3246 mt76: mt7915: add 6 GHz support
28ff1bddc7e8 mt76: mt7915: fix eeprom fields of txpower init values
d4b226cc15e7 mt76: mt7915: add txpower init for 6GHz
31e820d4ce4b mt76: mt7921: get rid of mt7921_wait_for_mcu_init declaration
9fee1faf6028 mt76: mt7915: check for devm_pinctrl_get() failure
31a970940b97 mt76: connac: make read-only array ba_range static const
e49af7036bbc mt76: use le32/16_get_bits() whenever possible
0664d39039c2 mt76: fix invalid rssi report
f16fc9d96105 mt76: mt7915: set band1 TGID field in tx descriptor
67ce2708dcef mt76: mt7915: fix beamforming mib stats
6e899abec818 mt76: mt7915: fix phy cap in mt7915_set_stream_he_txbf_caps()
c6780c85cff2 mt76: mt7915: fix typos in comments
aa6eadc09a83 mt76: usb: add req_type to ___mt76u_rr signature
74a519ab8353 mt76: usb: add req_type to ___mt76u_wr signature
2651d2c66cbd mt76: usb: introduce __mt76u_init utility routine
c03e095eee27 mt76: mt7921: disable runtime pm for usb
41085cdcd7e3 mt76: mt7921: update mt7921_skb_add_usb_sdio_hdr to support usb
e700aba6bae3 mt76: mt7921: move mt7921_usb_sdio_tx_prepare_skb in common mac code
056b7f4ebcc6 mt76: mt7921: move mt7921_usb_sdio_tx_complete_skb in common mac code.
0abf682a3def mt76: mt7921: move mt7921_usb_sdio_tx_status_data in mac common code.
b0c60d5252de mt76: mt7921: add mt7921u driver
053668acdaf8 mt76: mt7921: move mt7921_init_hw in a dedicated work
Signed-off-by: Felix Fietkau <nbd@nbd.name>
LOCK_STATE_HELD define was omitted during backport of
lockdep_assert_not_held() which leads to build failures of kernels with
CONFIG_LOCKDEP=y:
backports-5.15.8-1/backport-include/linux/lockdep.h:16:47: error: 'LOCK_STATE_HELD' undeclared (first use in this function)
Fix it by adding missing LOCK_STATE_HELD define.
References: PR#9373
Reported-by: Oskari Rauta <oskari.rauta@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
FCC ID: 2AG6R-AN700APIAC
Araknis AN-700-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:xb art 0x0
phy1 2.4G *:xc ---
phy0 5GHz *:xd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: 2AG6R-AN500APIAC
Araknis AN-500-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1200
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:e1 art 0x0
phy1 2.4G *:e2 ---
phy0 5GHz *:e3 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: U2M-AN300APIN
Araknis AN-300-AP-I-N is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EWS310AP
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM 1839ZFG V59C1512164QFJ25
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:7d art 0x0
phy1 2.4G *:7e ---
phy0 5GHz *:7f ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to
the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24 v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a SIPEX 3232EC for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
> Since the GS1900-24 v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Add option to compile kmod-inet-diag, support for INET (TCP, DCCP, etc)
socket monitoring interface used by native Linux tools such as ss.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
When porting mwan3 from iptables to nftables I tried the new translation
tool for ipset ipset-translate. I noticed that no IPv6 ipset can be
created with the tool. I have reported the problem to the upstream
project and the following patch fixes the problem.
Until this upsream is included in a new release, this patch should be
used in Openwrt.
https://lore.kernel.org/netfilter-devel/20220228190217.2256371-1-pablo@netfilter.org/T/#m09cc3cb738f2e42024c7aecf5b7240d9f6bbc19c
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
OpenWrt uses a lot of (b)ash scripts for initial setup. This isn't the
best solution as they almost never consider syncing files / data. Still
this is what we have and we need to try living with it.
Without proper syncing OpenWrt can easily get into an inconsistent state
on power cut. It's because:
1. Actual (flash) inode and data writes are not synchronized
2. Data writeback can take up to 30 seconds (dirty_expire_centisecs)
3. ubifs adds extra 5 seconds (dirty_writeback_centisecs) "delay"
Some possible cases (examples) for new files:
1. Power cut during 5 seconds after write() can result in all data loss
2. Power cut happening between 5 and 35 seconds after write() can result
in empty file (inode flushed after 5 seconds, data flush queued)
Above affects e.g. uci-defaults. After executing some migration script
it may get deleted (whited out) without generated data getting actually
written. Power cut will result in missing data and deleted file.
There are three ways of dealing with that:
1. Rewriting all user-space init to proper C with syncs
2. Trying bash hacks (like creating tmp files & moving them)
3. Adding sync and hoping for no power cut during critical section
This change introduces the last solution that is the simplest. It
reduces time during which things may go wrong from ~35 seconds to
probably less than a second. Of course it applies only to IO operations
performed before /etc/init.d/boot . It's probably the stage when the
most new files get created.
All later changes are usually done using smarter C apps (e.g. busybox or
uci) that creates tmp files and uses rename() that is expected to be
atomic.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Modems used in ZTE mobile broadband routers require to query the data
session status using the same CID as one used to establish the session,
otherwise they will report the session as "disconnected" despite
reporting correct PDH in previous step. Without this change, IPv6
connection on these modems doesn't establish properly. In IPv4 this bug
is present as well, but for some reason querying of IPv4 status works
using temporary CID, this however seems noncompliant with QMI
specifications, so fix it as well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Previously libxt_socket.so was included in iptables-mod-tproxy. It was
missed out when trying to make kmod-ipt-socket and kmod-ipt-tproxy
separate packages
Fixes: 4f443c88 ("netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxy")
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This patch adds the device-specific configuration to u-boot-envtools for
I-O DATA BSH-G24MB switch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This switches the iwlwifi-firmware-ax200 file to API version 66, this is
the most recent version supported by our driver.
The following files used in OpenWrt changed:
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_dmcub.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_010a.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_010b.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_0303.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_010a.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_010b.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_0303.bin
ar3k-firmware/lib/firmware/qca/rampatch_usb_00130200.bin
ar3k-firmware/lib/firmware/qca/rampatch_usb_00130201.bin
iwlwifi-firmware-ax200/lib/firmware/iwlwifi-cc-a0-66.ucode
iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0-66.ucode
iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode
iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode
rtl8822ce-firmware/lib/firmware/rtw88/rtw8822c_fw.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3276aed81c73 move run_cmd() to main.c
558eabc13c64 map: move dns host based lookup code to a separate function
6ff06d66c36c dns: add code for snooping dns packets
a78bd43c4a54 ubus: remove dnsmasq subscriber
9773ffa70f1f map: process dns patterns in the order in which they were defined
f13b67c9a786 dns: allow limiting dns entry matching to cname name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds the new tc-bpf variant and removes libxtables dependency from
the tc-tiny variant. The tc-full variant stays like before and contains
everything.
This allows to use tc without libxtables.
The variants have the following sizes:
root@OpenWrt:/# ls -al /usr/libexec/tc-*
-rwxr-xr-x 1 root root 282453 Mar 1 21:55 /usr/libexec/tc-bpf
-rwxr-xr-x 1 root root 282533 Mar 1 21:55 /usr/libexec/tc-full
-rwxr-xr-x 1 root root 266037 Mar 1 21:55 /usr/libexec/tc-tiny
They are linking the following shared libraries:
root@OpenWrt:/# ldd /usr/libexec/tc-tiny
/lib/ld-musl-mips-sf.so.1 (0x77d6e000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d4a000)
libc.so => /lib/ld-musl-mips-sf.so.1 (0x77d6e000)
root@OpenWrt:/# ldd /usr/libexec/tc-bpf
/lib/ld-musl-mips-sf.so.1 (0x77da6000)
libbpf.so.0 => /usr/lib/libbpf.so.0 (0x77d60000)
libelf.so.1 => /usr/lib/libelf.so.1 (0x77d3e000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d1a000)
libc.so => /lib/ld-musl-mips-sf.so.1 (0x77da6000)
libz.so.1 => /usr/lib/libz.so.1 (0x77cf6000)
root@OpenWrt:/# ldd /usr/libexec/tc-full
/lib/ld-musl-mips-sf.so.1 (0x77de8000)
libbpf.so.0 => /usr/lib/libbpf.so.0 (0x77da2000)
libelf.so.1 => /usr/lib/libelf.so.1 (0x77d80000)
libxtables.so.12 => /usr/lib/libxtables.so.12 (0x77d66000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d42000)
libc.so => /lib/ld-musl-mips-sf.so.1 (0x77de8000)
libz.so.1 => /usr/lib/libz.so.1 (0x77d1e000)
This is based on a patch from Tiago Gaspar.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add U-Boot environment settings for Ruijie RG-EW3200GX PRO to allow
users to access the bootloader environment using fw_printenv/fw_setenv
while running OpenWrt.
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Steps to reproduce:
1. Insert NVMe disk with a reduction to Turris Omnia
2. Go to U-boot
3. Run these two commands:
a) ``nvme scan``
b) ``nvme detail``
4. Wait for crash
This is backported from U-boot upstream repository.
It should be included in the upcoming release - 2022.04 [1].
It was tested on Turris Omnia, mvebu, cortex-a9, OpenWrt master.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20211209100639.21530-1-pali@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[Export the patch from U-Boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without PKG_RELEASE, it's impossible to trigger package updates when
changing files included in the package that are not in the qosify git
repository.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
The /tmp directory is mounted as tmpfs. The tmpfs filesystem is backed by
anonymous memory, which means it can be swapped out at any time, if there is
memory pressure [1]. For this reason, a zram swap device is a much better
choice than mounting /tmp on zram, since it's able to compress all anonymous
memory, and not just the memory assigned to /tmp. We already have the zram-swap
package for this specific purpose, which means procd's tmp-on-zram is both
redundant and more limited.
A follow-up patch will remove support for mounting /tmp in zram from procd
itself.
[1] https://www.kernel.org/doc/Documentation/filesystems/tmpfs.txt
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Update to the latest upstream version. In this version there is a new
tool with which you can convert ipsets into nftables sets. Since we are
now using nftables as default firewall, this could be a useful tool for
porting ipsets to nftables sets.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
iptables-nft doesn't depend on libip{4,6}tc, so move
libiptext* libs in their own packages to clean up dependencies
Rename libxtables-nft to libiptext-nft
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Using PROVIDES allows to have other packages continue to
depend on iptables and users to pick between legacy and nft
version.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
'iptables-mod-' can be used directly by firewall3, by
iptables and by iptables-nft. They are not linked to
iptables but to libxtables, so fix the dependencies to allow
to remove iptables(-legacy)
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
libxtables doesn't depend on libnftnl, iptables-nft does,
so move the dependency to not pull libnftnl with firewall3/iptables-legacy
Also libxtables-nft depends on IPTABLES_NFTABLES
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Debians' changelog by Henrique de Moraes Holschuh <hmh@debian.org>:
* upstream changelog: new upstream datafile 20220207
* Mitigates (*only* when loaded from UEFI firmware through the FIT)
CVE-2021-0146, INTEL-SA-00528: VT-d privilege escalation through
debug port, on Pentium, Celeron and Atom processors with signatures
0x506c9, 0x506ca, 0x506f1, 0x706a1, 0x706a8
https://github.com/intel/Intel-Linux-Processor-Microcode-Data-Files/issues/57#issuecomment-1036363145
* Mitigates CVE-2021-0127, INTEL-SA-00532: an unexpected code breakpoint
may cause a system hang, on many processors.
* Mitigates CVE-2021-0145, INTEL-SA-00561: information disclosure due
to improper sanitization of shared resources (fast-store forward
predictor), on many processors.
* Mitigates CVE-2021-33120, INTEL-SA-00589: out-of-bounds read on some
Atom Processors may allow information disclosure or denial of service
via network access.
* Fixes critical errata (functional issues) on many processors
* Adds a MSR switch to enable RAPL filtering (default off, once enabled
it can only be disabled by poweroff or reboot). Useful to protect
SGX and other threads from side-channel info leak. Improves the
mitigation for CVE-2020-8694, CVE-2020-8695, INTEL-SA-00389 on many
processors.
* Disables TSX in more processor models.
* Fixes issue with WBINDV on multi-socket (server) systems which could
cause resets and unpredictable system behavior.
* Adds a MSR switch to 10th and 11th-gen (Ice Lake, Tiger Lake, Rocket
Lake) processors, to control a fix for (hopefully rare) unpredictable
processor behavior when HyperThreading is enabled. This MSR switch
is enabled by default on *server* processors. On other processors,
it needs to be explicitly enabled by an updated UEFI/BIOS (with added
configuration logic). An updated operating system kernel might also
be able to enable it. When enabled, this fix can impact performance.
* Updated Microcodes:
sig 0x000306f2, pf_mask 0x6f, 2021-08-11, rev 0x0049, size 38912
sig 0x000306f4, pf_mask 0x80, 2021-05-24, rev 0x001a, size 23552
sig 0x000406e3, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 105472
sig 0x00050653, pf_mask 0x97, 2021-05-26, rev 0x100015c, size 34816
sig 0x00050654, pf_mask 0xb7, 2021-06-16, rev 0x2006c0a, size 43008
sig 0x00050656, pf_mask 0xbf, 2021-08-13, rev 0x400320a, size 35840
sig 0x00050657, pf_mask 0xbf, 2021-08-13, rev 0x500320a, size 36864
sig 0x0005065b, pf_mask 0xbf, 2021-06-04, rev 0x7002402, size 28672
sig 0x00050663, pf_mask 0x10, 2021-06-12, rev 0x700001c, size 28672
sig 0x00050664, pf_mask 0x10, 2021-06-12, rev 0xf00001a, size 27648
sig 0x00050665, pf_mask 0x10, 2021-09-18, rev 0xe000014, size 23552
sig 0x000506c9, pf_mask 0x03, 2021-05-10, rev 0x0046, size 17408
sig 0x000506ca, pf_mask 0x03, 2021-05-10, rev 0x0024, size 16384
sig 0x000506e3, pf_mask 0x36, 2021-04-29, rev 0x00ec, size 108544
sig 0x000506f1, pf_mask 0x01, 2021-05-10, rev 0x0036, size 11264
sig 0x000606a6, pf_mask 0x87, 2021-12-03, rev 0xd000331, size 291840
sig 0x000706a1, pf_mask 0x01, 2021-05-10, rev 0x0038, size 74752
sig 0x000706a8, pf_mask 0x01, 2021-05-10, rev 0x001c, size 75776
sig 0x000706e5, pf_mask 0x80, 2021-05-26, rev 0x00a8, size 110592
sig 0x000806a1, pf_mask 0x10, 2021-09-02, rev 0x002d, size 34816
sig 0x000806c1, pf_mask 0x80, 2021-08-06, rev 0x009a, size 109568
sig 0x000806c2, pf_mask 0xc2, 2021-07-16, rev 0x0022, size 96256
sig 0x000806d1, pf_mask 0xc2, 2021-07-16, rev 0x003c, size 101376
sig 0x000806e9, pf_mask 0x10, 2021-04-28, rev 0x00ec, size 104448
sig 0x000806e9, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 104448
sig 0x000806ea, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 103424
sig 0x000806eb, pf_mask 0xd0, 2021-04-28, rev 0x00ec, size 104448
sig 0x000806ec, pf_mask 0x94, 2021-04-28, rev 0x00ec, size 104448
sig 0x00090661, pf_mask 0x01, 2021-09-21, rev 0x0015, size 20480
sig 0x000906c0, pf_mask 0x01, 2021-08-09, rev 0x2400001f, size 20480
sig 0x000906e9, pf_mask 0x2a, 2021-04-29, rev 0x00ec, size 106496
sig 0x000906ea, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 102400
sig 0x000906eb, pf_mask 0x02, 2021-04-28, rev 0x00ec, size 104448
sig 0x000906ec, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 103424
sig 0x000906ed, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 103424
sig 0x000a0652, pf_mask 0x20, 2021-04-28, rev 0x00ec, size 93184
sig 0x000a0653, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 94208
sig 0x000a0655, pf_mask 0x22, 2021-04-28, rev 0x00ee, size 94208
sig 0x000a0660, pf_mask 0x80, 2021-04-28, rev 0x00ea, size 94208
sig 0x000a0661, pf_mask 0x80, 2021-04-29, rev 0x00ec, size 93184
sig 0x000a0671, pf_mask 0x02, 2021-08-29, rev 0x0050, size 102400
* Removed Microcodes:
sig 0x00080664, pf_mask 0x01, 2021-02-17, rev 0xb00000f, size 130048
sig 0x00080665, pf_mask 0x01, 2021-02-17, rev 0xb00000f, size 130048
* update .gitignore and debian/.gitignore.
Add some missing items from .gitignore and debian/.gitignore.
* ucode-blacklist: do not late-load 0x406e3 and 0x506e3.
When the BIOS microcode is older than revision 0x7f (and perhaps in some
other cases as well), the latest microcode updates for 0x406e3 and
0x506e3 must be applied using the early update method. Otherwise, the
system might hang. Also: there must not be any other intermediate
microcode update attempts [other than the one done by the BIOS itself],
either. It must go from the BIOS microcode update directly to the
latest microcode update.
* source: update symlinks to reflect id of the latest release, 20220207
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
iucode-tool/host is used by intel-microcode to manipulate with
microcode.bin file. iucode-tool requires cpuid.h at compile time
for autodection feature, but non-x86 build hosts does not have
this header file (e.g. ubuntu 20.04 aarch64) or this header
generates compile time error (#error macro) (e.g. macos arm64).
This patch provides compat cpuid.h to build iucode-tool/host on
non-x86 linux hosts and macos. CPU autodectection is not required
for intel-microcode package build so compat cpuid.h is ok for
OpenWrt purposes.
glibc and argp lib are not present in macos so iucode-tool/host
build fails. This patch adds argp-standalone/host as build
dependency if host os is macos.
Generated ucode (intel-microcode package) is exactly the same on
Linux x86_64 (Ubuntu 20.04), Linux aarch64 (Ubuntu 20.04) and
Darwin arm64 (MacOS 11.6) build hosts.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
This patch adds host-compile ability to argp-standalone for build
hosts without glibc and argp lib, e.g. MacOS.
iucode-tool/host can not be built on MacOS due to lack of argp.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
<https://github.com/ARMmbed/mbedtls/releases/tag/v2.28.0>
"Mbed TLS 2.28 is a long-time support branch.
It will be supported with bug-fixes and security
fixes until end of 2024."
<https://github.com/ARMmbed/mbedtls/blob/development/BRANCHES.md>
"Currently, the only supported LTS branch is: mbedtls-2.28.
For a short time we also have the previous LTS, which has
recently ended its support period, mbedtls-2.16.
This branch will move into the archive namespace around the
time of the next release."
this will also add support for uacme ualpn support.
size changes
221586 libmbedtls12_2.28.0-1_mips_24kc.ipk
182742 libmbedtls12_2.16.12-1_mips_24kc.ipk
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
(remark about 2.16's EOS, slightly reworded)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ZTE MF286A and MF286R are indoor LTE category 6/7 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.
Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: W25N01GV 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9886 2x2 MIMO 802.11ac Wave2 radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN:
[MF286A] MDM9230-based category 6 internal LTE modem
[MF286R] PXA1826-based category 7 internal LTE modem
in extended mini-PCIE form factor, with 3 internal antennas and
2 external antenna connections, single mini-SIM slot.
- FXS: one external ATA port (handled entirely by modem part) with two
physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
Signal state) handled entirely by modem. 4 link status LEDs handled by
the switch on the backside.
- Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and
monitoring handled by modem.
- Label MAC device: eth0
The device shares many components with previous model, MF286, differing
mostly by a Wave2 5GHz radio, flash layout and internal LED color.
In case of MF286A, the modem is the same as in MF286. MF286R uses a
different modem based on Marvell PXA1826 chip.
Internal modem of MF286A is supported via uqmi, MF286R modem isn't fully
supported, but it is expected to use comgt-ncm for connection, as it
uses standard 3GPP AT commands for connection establishment.
Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.
Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.
STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
version before installation, to have built-in modem at the latest firmware
version.
STEP 1: gaining root shell:
Method 1:
This works if busybox has telnetd compiled in the binary.
If this does not work, try method 2.
Using well-known exploit to start telnetd on your router - works
only if Busybox on stock firmware has telnetd included:
- Open stock firmware web interface
- Navigate to "URL filtering" section by going to "Advanced settings",
then "Firewall" and finally "URL filter".
- Add an entry ending with "&&telnetd&&", for example
"http://hostname/&&telnetd&&".
- telnetd will immediately listen on port 4719.
- After connecting to telnetd use "admin/admin" as credentials.
Method 2:
This works if busybox does not have telnetd compiled in. Notably, this
is the case in DNA.fi firmware.
If this does not work, try method 3.
- Set IP of your computer to 192.168.0.22. (or appropriate subnet if
changed)
- Have a TFTP server running at that address
- Download MIPS build of busybox including telnetd, for example from:
https://busybox.net/downloads/binaries/1.21.1/busybox-mips
and put it in it's root directory. Rename it as "telnetd".
- As previously, login to router's web UI and navigate to "URL
filtering"
- Using "Inspect" feature, extend "maxlength" property of the input
field named "addURLFilter", so it looks like this:
<input type="text" name="addURLFilter" id="addURLFilter" maxlength="332"
class="required form-control">
- Stay on the page - do not navigate anywhere
- Enter "http://aa&zte_debug.sh 192.168.0.22 telnetd" as a filter.
- Save the settings. This will download the telnetd binary over tftp and
execute it. You should be able to log in at port 23, using
"admin/admin" as credentials.
Method 3:
If the above doesn't work, use the serial console - it exposes root shell
directly without need for login. Some stock firmwares, notably one from
finnish DNA operator lack telnetd in their builds.
STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.
It is highly recommended to perform backup using both methods, to avoid
hassle of reassembling firmware images in future, if a restore is
needed.
Method 1: after booting OpenWrt initramfs image via TFTP:
PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION.
- Dump stock firmware located on stock kernel and ubi partitions:
ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
ssh root@192.168.1.1: cat /dev/mtd9 > mtd9_ubi.bin
And keep them in a safe place, should a restore be needed in future.
Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:
cat /proc/mtd
It should show the following:
mtd0: 000a0000 00010000 "u-boot"
mtd1: 00020000 00010000 "u-boot-env"
mtd2: 00140000 00010000 "reserved1"
mtd3: 000a0000 00020000 "fota-flag"
mtd4: 00080000 00020000 "art"
mtd5: 00080000 00020000 "mac"
mtd6: 000c0000 00020000 "reserved2"
mtd7: 00400000 00020000 "cfg-param"
mtd8: 00400000 00020000 "log"
mtd9: 000a0000 00020000 "oops"
mtd10: 00500000 00020000 "reserved3"
mtd11: 00800000 00020000 "web"
mtd12: 00300000 00020000 "kernel"
mtd13: 01a00000 00020000 "rootfs"
mtd14: 01900000 00020000 "data"
mtd15: 03200000 00020000 "fota"
mtd16: 01d00000 00020000 "firmware"
Differences might indicate that this is NOT a MF286A device but
one of other variants.
- Copy over all MTD partitions, for example by executing the following:
for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15; do cat /dev/mtd$i > \
/var/usb_disk/mtd$i; done
"Firmware" partition can be skipped, it is a concatenation
of "kernel" and "rootfs".
- If the count of MTD partitions is different, this might indicate that
this is not a MF286A device, but one of its other variants.
- (optionally) rename the files according to MTD partition names from
/proc/mtd
- Unmount the filesystem:
umount /var/usb_disk; sync
and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
firmware. This is especially important, because stock firmware for
this device is not available officially, and is usually customized by
the mobile providers.
STEP 3: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.0.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.0.22
setenv ipaddr 192.168.0.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
Method 2: using initramfs image as temporary boot kernel
This exploits the fact, that kernel and rootfs MTD devices are
consecutive on NAND flash, so from within stock image, an initramfs can
be written to this area and booted by U-boot on next reboot, because it
uses "nboot" command which isn't limited by kernel partition size.
- Download the initramfs-kernel.bin image
- After backing up the previous MTD contents, write the images to the
"firmware" MTD device, which conveniently concatenates "kernel" and
"rootfs" partitions that can fit the initramfs image:
nandwrite -p /dev/<firmware-mtd> \
/var/usb_disk/openwrt-ath79-zte_mf286a-initramfs-kernel.bin
- If write is OK, reboot the device, it will reboot to OpenWrt
initramfs:
reboot -f
- After rebooting, SSH into the device and use sysupgrade to perform
proper installation.
Method 3: using built-in TFTP recovery (LAST RESORT):
- With that method, ensure you have complete backup of system's NAND
flash first. It involves deliberately erasing the kernel.
- Download "-initramfs-kernel.bin" image for the device.
- Prepare the recovery image by prepending 8MB of zeroes to the image,
and name it root_uImage:
dd if=/dev/zero of=padding.bin bs=8M count=1
cat padding.bin openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin >
root_uImage
- Set up a TFTP server at 192.0.0.1/8. Router will use random address
from that range.
- Put the previously generated "root_uImage" into TFTP server root
directory.
- Deliberately erase "kernel" partition" using stock firmware after
taking backup. THIS IS POINT OF NO RETURN.
- Restart the device. U-boot will attempt flashing the recovery
initramfs image, which will let you perform actual installation using
sysupgrade. This might take a considerable time, sometimes the router
doesn't establish Ethernet link properly right after booting. Be
patient.
- After U-boot finishes flashing, the LEDs of switch ports will all
light up. At this moment, perform power-on reset, and wait for OpenWrt
initramfs to finish booting. Then proceed to actual installation.
STEP 4: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:
scp openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
STEP 5: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth '<auth>' # As required, usually 'none'
option pincode '<pin>' # If required by SIM
option apn '<apn>' # As required by ISP
option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'
For example, the following works for most polish ISPs
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth 'none'
option apn 'internet'
option pdptype 'ipv4'
The required minimum is:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
In this case, the modem will use last configured APN from stock
firmware - this should work out of the box, unless your SIM requires
PIN which can't be switched off.
If you have build with LuCI, installing luci-proto-qmi helps with this
task.
Restoring the stock firmware:
Preparation:
If you took your backup using stock firmware, you will need to
reassemble the partitions into images to be restored onto the flash. The
layout might differ from ISP to ISP, this example is based on generic stock
firmware
The only partitions you really care about are "web", "kernel", and
"rootfs". These are required to restore the stock firmware through
factory TFTP recovery.
Because kernel partition was enlarged, compared to stock
firmware, the kernel and rootfs MTDs don't align anymore, and you need
to carve out required data if you only have backup from stock FW:
- Prepare kernel image
cat mtd12_kernel.bin mtd13_rootfs.bin > owrt_kernel.bin
truncate -s 4M owrt_kernel_restore.bin
- Cut off first 1MB from rootfs
dd if=mtd13_rootfs.bin of=owrt_rootfs.bin bs=1M skip=1
- Prepare image to write to "ubi" meta-partition:
cat mtd6_reserved2.bi mtd7_cfg-param.bin mtd8_log.bin mtd9_oops.bin \
mtd10_reserved3.bin mtd11_web.bin owrt_rootfs.bin > \
owrt_ubi_ubi_restore.bin
You can skip the "fota" partition altogether,
it is used only for stock firmware update purposes and can be overwritten
safely anyway. The same is true for "data" partition which on my device
was found to be unused at all. Restoring mtd5_cfg-param.bin will restore
the stock firmware configuration you had before.
Method 1: Using initramfs:
This method is recmmended if you took your backup from within OpenWrt
initramfs, as the reassembly is not needed.
- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Look up the kernel and ubi partitions in /proc/mtd
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
(scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
mtd write <kernel_mtd> mtd4_kernel.bin
rm mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
restore them individually. Otherwise you might run out of space in
tmpfs:
(scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin
rm mtd3_ubiconcat0.bin
(scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin
rm mtd5_ubiconcat1.bin
- If the write was correct, force a device reboot with
reboot -f
Method 2: Using live OpenWrt system (NOT RECOMMENDED):
- Prepare a USB flash drive contatining MTD backup files
- Ensure you have kmod-usb-storage and filesystem driver installed for
your drive
- Mount your flash drive
mkdir /tmp/usb
mount /dev/sda1 /tmp/usb
- Remount your UBI volume at /overlay to R/O
mount -o remount,ro /overlay
- Write back the kernel and ubi partitions from USB drive
cd /tmp/usb
mtd write mtd4_kernel.bin /dev/<kernel_mtd>
mtd write mtd9_ubi.bin /dev/<kernel_ubi>
- If everything went well, force a device reboot with
reboot -f
Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota"
MTD partition which may be safely erased after reboot anyway.
Method 3: using built-in TFTP recovery:
This method is recommended if you took backups using stock firmware.
- Assemble a recovery rootfs image from backup of stock partitions by
concatenating "web", "kernel", "rootfs" images dumped from the device,
as "root_uImage"
- Use it in place of "root_uImage" recovery initramfs image as in the
TFTP pre-installation method.
Quirks and known issuesa
- It was observed, that CH340-based USB-UART converters output garbage
during U-boot phase of system boot. At least CP2102 is known to work
properly.
- Kernel partition size is increased to 4MB compared to stock 3MB, to
accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
image is at 2.5MB which is dangerously close to the limit. This has no
effect on booting the system - but keep that in mind when reassembling
an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
you used before in stock firmware first. If you need to change it,
please use protocok '3g' to establish connection once, or use the
following command to change APN (and optionally IP type) manually:
echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the blue debug LED hidden
inside the case. All other LEDs are controlled by modem, on which the
router part has some influence only on Wi-Fi LED.
- Wi-Fi LED currently doesn't work while under OpenWrt, despite having
correct GPIO mapping. All other LEDs are controlled by modem,
including this one in stock firmware. GPIO19, mapped there only acts
as a gate, while the actual signal source seems to be 5GHz Wi-Fi
radio, however it seems it is not the LED exposed by ath10k as
ath10k-phy0.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
reset of whole board, not only the modem. It is attached to
gpio-restart driver, to restart the modem on reboot as well, to ensure
QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
for OpenWrt operation at all - have fun lurking around.
The same modem module is used as in older MF286.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Both struct net_device_path_ctx and struct net_device_path
are not available in 5.4. This causes an build error on the
bcm63xx target.
|mac80211/driver-ops.h: In function 'drv_net_fill_forward_path':
|driver-ops.h:1502:57: error: passing argument 4 of
|'local->ops->net_fill_forward_path' from incompatible pointer type
| [-Werror=incompatible-pointer-types]
| 1502 | ctx, path);
| | ^~~
| | |
| | struct net_device_path_ctx *
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Package the ability to log kernel crashes to 'ramoops' pstore
files into RAM in /sys/fs/pstore
Reference to the ramoops admin guide in upstream Linux:
https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html
The files in RAM survive a warm reboot, but not a cold reboot.
Note: kmod-ramoops selects kmod-pstore and kmod-reed-solomon.
The feature can be used by selecting the kmod-ramoops and
adding a ramoops reserved-memory definition to the device DTS.
Example from R7800:
reserved-memory {
rsvd@5fe00000 {
reg = <0x5fe00000 0x200000>;
reusable;
};
ramoops@42100000 {
compatible = "ramoops";
reg = <0x42100000 0x40000>;
record-size = <0x4000>;
console-size = <0x4000>;
ftrace-size = <0x4000>;
pmsg-size = <0x4000>;
};
};
If no definition has been made in DTS, no crash log is stored
for the device.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(added CONFIG_EFI_VARS_PSTORE disable)
Previously, grub2 was hardcoded to always look on "hd0" for the
kernel.
This works well when the system only had a single disk.
But if there was a second disk/stick present, it may have look
on the wrong drive because of enumeration races.
This patch utilizes grub2 search function to look for a filesystem
with the label "kernel". This works thanks to existing setup in
scripts/gen_image_generic.sh. Which sets the "kernel" label on
both the fat and ext4 filesystem variants.
Signed-off-by: Jax Jiang <jax.jiang.007@gmail.com>
Suggested-by: Alberto Bursi <bobafetthotmail@gmail.com> (MX100 WA)
(word wrapped, slightly rewritten commit message, removed MX100 WA)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
AT91Bootstrap version 4 is available only for SAM9X60, SAMA5D2, SAMA5D3,
SAMA5D4, SAMA7G5. Thus use v4.0.1 for the above targets and v3.10.4 for
the rest of them. With the switch to v4 AT91Bootstrap binaries are now
on build/binaries. Take also this into account. Also, patches directory
is not needed anymore with the version update.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
In the default shadow file, as visible in the failsafe mode, the user
root has value of `0` set in the 3rd field, the date of last password
change. This setting means that the password needs to be changed the
next time the user will log in the system. `dropbear` server is ignoring
this setting but `openssh-server` tries to enforce it and fails in the
failsafe mode because the rootfs is R/O.
Disable the password aging feature for user root by setting the 3rd
filed empty.
Signed-off-by: Rucke Teg <rucketeg@protonmail.com>
Enable both the hunting-and-pecking loop and hash-to-element mechanisms
by default in OpenWRT with SAE.
Commercial Wi-Fi solutions increasingly frequently now ship with both
hunting-and-pecking and hash-to-element (H2E) enabled by default as this
is more secure and more performant than offering hunting-and-pecking
alone for H2E capable clients.
The hunting and pecking loop mechanism is inherently fragile and prone to
timing-based side channels in its design and is more computationally
intensive to perform. Hash-to-element (H2E) is its long-term
replacement to address these concerns.
For clients that only support the hunting-and-pecking loop mechanism,
this is still available to use by default.
For clients that in addition support, or were to require, the
hash-to-element (H2E) mechanism, this is then available for use.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Backport fix for API breakage of SSL_get_verify_result() introduced in
v5.1.1-stable. In v4.8.1-stable SSL_get_verify_result() used to return
X509_V_OK when used on LE powered sites or other sites utilizing
relaxed/alternative cert chain validation feature. After an update to
v5.1.1-stable that API calls started returning X509_V_ERR_INVALID_CA
error and thus rendered all such connection attempts imposible:
$ docker run -it openwrt/rootfs:x86_64-21.02.2 sh -c "wget https://letsencrypt.org"
Downloading 'https://letsencrypt.org'
Connecting to 18.159.128.50:443
Connection error: Invalid SSL certificate
Fixes: #9283
References: https://github.com/wolfSSL/wolfssl/issues/4879
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Not all targets create /var/lock or touch /var/lock/fw_printenv.lock in
their platform.sh. This is problematic as fw_printenv then fails in
case /var/lock/fw_printenv.lock has not been created by previous calls
to fw_printenv/fw_setenv before sysupgrade is run.
Targets using fw_printenv/fw_setenv during sysupgrade:
* ath79/*
* ipq40xx/*
* ipq806x/*
* kirkwood/*
* layerscape/*
* mediatek/mt7622
* mvebu/*
* ramips/*
* realtek/*
Targets currently using additional steps in /lib/upgrade/platform.sh
to make sure /var/lock/fw_printenv.lock (or at least /var/lock)
actually exists:
* ath79/* (openmesh devices)
* ipq40xx/* (linksys devices)
* ipq806x/* (linksys devices)
* kirkwood/* (linksys devices)
* layerscape/*
* mvebu/cortexa9 (linksys devices)
Given that accessing the U-Boot environment during sysupgrade is not
uncommon and the situation across targets is currently quite diverse,
just make sure both tools as well fw_env.config are always copied to
the ramdisk used for sysupgrade. Also make sure /var/lock always
exists.
This now allows to remove copying of fw_printenv/fw_setenv as well as
fw_env.config, creation of /var/lock or even /var/lock/fw_printenv.lock
from lib/upgrade/platform.sh or files included there.
As the same applies also to 'fwtool' which is used by generic eMMC
sysupgrade, also always copy that to ramdisk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This uses uci to configure engines, by generating a list of enabled
engines in /var/etc/ssl/engines.cnf from engines configured in
/etc/config/openssl:
config engine 'devcrypto'
option enabled '1'
Currently the only options implemented are 'enabled', which defaults to
true and enables the named engine, and the 'force' option, that enables
the engine even if the init script thinks the engine does not exist.
The existence test is to check for either a configuration file
/etc/ssl/engines.cnf.d/%ENGINE%.cnf, or a shared object file
/usr/lib/engines-1.1/%ENGINE%.so.
The engine list is generated by an init script which is set to run after
'log' because it informs the engines being enabled or skipped. It
should run before any service using OpenSSL as the crypto library,
otherwise the service will not use any engine.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This enables an engine during its package's installation, by adding it
to the engines list in /etc/ssl/engines.cnf.d/engines.cnf.
The engine build system was reworked, with the addition of an engine.mk
file that groups some of the engine packages' definitions, and could be
used by out of tree engines as well.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This changes the configuration of engines from the global openssl.cnf to
files in the /etc/ssl/engines.cnf.d directory. The engines.cnf file has
the list of enabled engines, while each engine has its own configuration
file installed under /etc/ssl/engines.cnf.d.
Patches were refreshed with --zero-commit.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
100-ddr-marvell-a38x-fix-BYTE_HOMOGENEOUS_SPLIT_OUT-deci.patch [1]:
SoC Marvell A38x is used in Turris Omnia, and we thought that with recent
fiddling around DDR training to fix it once for all, there were
reproduced the issue in the upcoming new revision Turris Omnia boards.
101-arm-mvebu-spl-Add-option-to-reset-the-board-on-DDR-t.patch [2]:
This is useful when some board may occasionally fail with DDR training,
and it adds the option to reset the board on the DDR training failure
102-arm-mvebu-turris_omnia-Reset-the-board-immediately-o.patch [3]:
This enables the option CONFIG_DDR_RESET_ON_TRAINING_FAILURE (added by
101 patch), so the Turris Omnia board is restarted immediately, and it
does not require to reset the board manually or wait 120s for MCU to
reset the board
[1] https://patchwork.ozlabs.org/project/uboot/patch/20220217000837.13003-1-kabel@kernel.org/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-1-kabel@kernel.org/
[3] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-2-kabel@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This commit adds the following package compile options.
CONFIG_PACKAGE_RTW88_DEBGUG:
Compile the driver with additional debug logging output
CONFIG_PACKAGE_RTW88_DEBGUGFS:
Add the possibility to map information about the driver rtw88 into
debugfs.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Contains following changes:
136006b88826 cmake: fix usage of implicit library and include paths
bc0e84d689e2 netifd: interface-ip: don't set fib6 policies if ipv6 disabled
Signed-off-by: Petr Štetiar <ynezz@true.cz>
e061299 wireless-regdb: Raise DFS TX power limit to 250 mW (24 dBm) for the US
2ce78ed wireless-regdb: Update regulatory rules for Croatia (HR) on 6GHz
0d39f4c wireless-regdb: Update regulatory rules for South Korea (KR)
acad231 wireless-regdb: Update regulatory rules for France (FR) on 6 and 60 GHz
ea83a82 wireless-regdb: add support for US S1G channels
4408149 wireless-regdb: add 802.11ah bands to world regulatory domain
5f3cadc wireless-regdb: Update regulatory rules for Spain (ES) on 6GHz
e0ac69b Revert "wireless-regdb: Update regulatory rules for South Korea (KR)"
40e5e80 wireless-regdb: Update regulatory rules for South Korea (KR)
e427ff2 wireless-regdb: Update regulatory rules for China (CN)
0970116 wireless-regdb: Update regulatory rules for the Netherlands (NL) on 6GHz
4dac44b wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
package hwmon's lm70.ko. This module supports the
National Semiconductor/TI LM70,LM71,LM74 and
TI TMP121,TMP122,TMP123 and TMP124 chips (all SPI).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When Kernel 5.10 was enabled for mpc85xx, the kernel once again became too
large upon decompression (>7MB or so) to decompress itself on boot (see
FS#4110[1]).
There have been many attempts to fix booting from a compressed kernel on
the HiveAP-330:
- b683f1c36d ("mpc85xx: Use gzip compressed kernel on HiveAP-330")
- 98089bb8ba ("mpc85xx: Use uncompressed kernel on the HiveAP-330")
- 26cb167a5c ("mpc85xx: Fix Aerohive HiveAP-330 initramfs image")
We can no longer compress the kernel due to size, and the stock bootloader
does not support any other types of compression. Since an uncompressed
kernel no longer fits in the 8MiB kernel partition at 0x2840000, we need to
patch u-boot to autoboot by running variable which isn't set by the
bootloader on each autoboot.
This commit repartitions the HiveAP, requiring a new COMPAT_VERSION,
and uses the DEVICE_COMPAT_MESSAGE to guide the user to patch u-boot,
which changes the variable run on boot to be `owrt_boot`; the user can
then set the value of that variable appropriately.
The following has been documented in the device's OpenWrt wiki page:
<https://openwrt.org/toh/aerohive/hiveap-330>. Please look there
first/too for more information.
The from-stock and upgrade from a previous installation now becomes:
0) setup a network with a dhcp server and a tftp server at serverip
(192.168.1.101) with the initramfs image in the servers root directory.
1) Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted. If the password
doesn't work. Try reseting the device by pressing and holding the reset
button with the stock OS.
2) Once in U-Boot, set the new owrt_boot and tftp+boot the initramfs image:
Use copy and paste!
# fw_setenv owrt_boot 'setenv bootargs \"console=ttyS0,$baudrate\";bootm 0xEC040000 - 0xEC000000'
# save
# dhcp
# setenv bootargs console=ttyS0,$baudrate
# tftpboot 0x1000000 192.168.1.101:openwrt-mpc85xx-p1020-aerohive_hiveap-330-initramfs-kernel.bin
# bootm
3) Once openwrt booted:
carefully copy and paste this into the root shell. One step at a time
# 3.0 install kmod-mtd-rw from the internet and load it
opkg update; opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=y
# 3.1 create scripts that modifies uboot
cat <<- "EOF" > /tmp/uboot-update.sh
. /lib/functions/system.sh
cp "/dev/mtd$(find_mtd_index 'u-boot')" /tmp/uboot
cp /tmp/uboot /tmp/uboot_patched
ofs=$(strings -n80 -td < /tmp/uboot | grep '^ [0-9]* setenv bootargs.*cp\.l' | cut -f2 -d' ')
for off in $ofs; do
printf "run owrt_boot; " | dd of=/tmp/uboot_patched bs=1 seek=${off} conv=notrunc
done
md5sum /tmp/uboot*
EOF
# 3.2 run the script to do the modification
sh /tmp/uboot-update.sh
# verify that /tmp/uboot and /tmp/uboot_patched are good
#
# my uboot was: (is printed during boot)
# U-Boot 2009.11 (Jan 12 2017 - 00:27:25), Build: jenkins-HiveOS-Honolulu_AP350_Rel-245
#
# d84b45a2e8aca60d630fbd422efc6b39 /tmp/uboot
# 6dc420f24c2028b9cf7f0c62c0c7f692 /tmp/uboot_patched
# 98ebc7e7480ce9148cd2799357a844b0 /tmp/uboot-update.sh <-- just for reference
# 3.3 this produces the /tmp/u-boot_patched file.
mtd write /tmp/uboot_patched u-boot
3) scp over the sysupgrade file to /tmp/ and run sysupgrade to flash OpenWrt:
sysupgrade -n /tmp/openwrt-mpc85xx-p1020-aerohive_hiveap-330-squashfs-sysupgrade.bin
4) after the reboot, you are good to go.
Other notes:
- Note that after this sysupgrade, the AP will be unavailable for 7 minutes
to reformat flash. The tri-color LED does not blink in any way to
indicate this, though there is no risk in interrupting this process,
other than the jffs2 reformat being reset.
- Add a uci-default to fix the compat version. This will prevent updates
from previous versions without going through the installation process.
- Enable CONFIG_MTD_SPLIT_UIMAGE_FW and adjust partitioning to combine
the kernel and rootfs into a single dts partition to maximize storage
space, though in practice the kernel can grow no larger than 16MiB due
to constraints of the older mpc85xx u-boot platform.
- Because of that limit, KERNEL_SIZE has been raised to 16m.
- A .tar.gz of the u-boot source for the AP330 (a.k.a. Goldengate) can
be found here[2].
- The stock-jffs2 partition is also removed to make more space -- this
is possible only now that it is no longer split away from the rootfs.
- the console-override is gone. The device will now get the console
through the bootargs. This has the advantage that you can set a different
baudrate in uboot and the linux kernel will stick with it!
- due to the repartitioning, the partition layout and names got a makeover.
- the initramfs+fdt method is now combined into a MultiImage initramfs.
The separate fdt download is no longer needed.
- added uboot-envtools to the mpc85xx target. All targets have uboot and
this way its available in the initramfs.
[1]: https://bugs.openwrt.org/index.php?do=details&task_id=4110
[2]: magnet:?xt=urn:btih:e53b27006979afb632af5935fa0f2affaa822a59
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(rewrote parts of the commit message, Initramfs-MultiImage,
dropped bootargs-override, added wiki entry + link, uboot-envtools)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ksmbd is an upstream linux alternative to Samba which is lighterweight
and more performant, especially on underpowered devices.
Moving it here from the packages feed as it is now an upstream kernel
module. Also easier to update as version updates can be coordinated better
The next LTS kernel (5.15) has this included. A depend on kernel < 5.15
will need to be added later.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The 80211r r0kh and r1kh defaults are generated from the md5sum of
"$mobility_domain/$auth_secret". auth_secret is only set when using EAP
authentication, but the default key is used for SAE/PSK as well. In
this case, auth_secret is empty, and the default value of the key can
be computed from the SSID alone.
Fallback to using $key when auth_secret is empty. While at it, rename
the variable holding the generated key from 'key' to 'ft_key', to avoid
clobbering the PSK.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[make ft_key local]
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the STAs extended capabilities to the ubus STA information. This
way, external daemons can be made aware of a STAs capabilities.
This field is of an array type and contains 0 or more bytes of a STAs
advertised extended capabilities.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for creation heartbeat led trigger with,
for example, this command:
ucidef_set_led_heartbeat "..." "..." "..."
from /etc/board.d/01_leds.
Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
This module was used solely by Buffalo WZR-HP-G300NH devices
and has become obsolete with the introduction of gpio-cascade.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Adds new kernel module for GPIO controlled multiplexer support.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]
a87d010 uxc: remove unused printf parameter
ad65249 instance: exit in case asprintf() fails
Build with glibc should again work after this commit.
Fixes: e9e61d76fd ("procd: update to git HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
df1123e uxc: add support for user-defined settings
0272c7c uxc: allow editing settings using 'create'
a839518 uxc: clean up error handling
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For sysupgrade on NAND/UBI devices there is the U-Boot environment
variable rootfs_data_max which can be used to limit the size of the
rootfs_data volume created on sysupgrade.
This stopped working reliable with recent kernels, probably due to a
race condition when reading the number of free erase blocks from sysfs
just after removing a volume.
Change the script to just try creating rootfs_data with the desired
size and retry with maximum size in case that fails. Hence calculating
the available size in the script can be dropped which works around the
problem.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
'uxc boot' is inteded to be called multiple times, so there is not need
to guard the first call on boot -- the actual code anyway didn't do
that, so just remove it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes the following security problem:
The command-line argument parser in tcpdump before 4.99.0 has a buffer
overflow in tcpdump.c:read_infile(). To trigger this vulnerability the
attacker needs to create a 4GB file on the local filesystem and to
specify the file name as the value of the -F command-line argument of
tcpdump.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
53caa1a fw4: resolve zone layer 2 devices for hw flow offloading
9fe58f5 fw4: rework and fix family inheritance logic
8795296 tests: mocklib: fix infinite recursion in wrapped print()
281b1bc tests: change mocked wan interface type to PPPoE
93b710d tests: mocklib: forward compatibility change
1a94915 fw4: only stage reflection rules if all required addrs are known
5c21714 fw4: add device iifname/oifname matches to DSCP and MARK rules
3eacc97 tests: adjust 01_ruleset test case to latest changes
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
a29bad9 compiler: fix patchlist corruption on switch statement syntax errors
86f0662 lib: change `ord()` to always return single byte value
116a8ce vallist: fix storing/retrieving short strings with 8bit byte value
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When the uci configuration is created automatically during a very early
stage, where no entropy daemon is set up, generating the key directly is
not an option. Therefore we allow to set the private_key to "generate"
and generate the private key directly before the interface is taken up.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
Tested-by: Jan-Niklas Burfeind <git@aiyionpri.me>
11adf0c source: convert source objects into proper uc_value_t type
3a49192 treewide: rework function memory model
7edad5c tests: add functional tests for builtin functions
d5003fd lib: fix leaking tokener in uc_json() on parse exception
5d0ecd9 lib: fix infinite loop on empty regexp matches in uc_replace()
3ad57f1 lib: fix infinite loop on empty regexp matches in uc_match()
32d596d lib: fix infinite loop on empty regexp matches in uc_split()
3e3f38d vm: ensure consistent trace output between gcc and clang compiled ucode
3600ded vm: fix leaking function value on call exception
3059295 vm: NULL-initialize pointer to make cppcheck happy
98e59bf source: zero-initialize conversion union to make cppcheck happy
7a65c14 run_tests.sh: change workdir to testcase directory during execution
afec8d7 run_tests.sh: support placing supplemental testcase files
3ada6e0 run_tests.sh: always treat outputs as text data
2cb627f program: rename bytecode load/write functions, track path of executed file
1094ffa lib: fix memory leak in uc_require_ucode()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
Hardware
--------
SoC: QCN5502
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 1 gigabit port
Wireless No1: QCN5502 on-chip 2.4GHz 4x4
Wireless No2: QCA9984 pcie 5GHz 4x4
USB: none
Installation
------------
Flash the factory image using the stock web interface or TFTP the
factory image to the bootloader.
What works
----------
- LEDs
- Ethernet port
- 5GHz wifi (QCA9984 pcie)
What doesn't work
-----------------
- 2.4GHz wifi (QCN5502 on-chip)
(I was not able to make this work, probably because ath9k requires
some changes to support QCN5502.)
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
fgrep is deprecated and replaced by grep -F. The latter is used
throughout the tree whereas this is the only usage of the former.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Now that we have separate files for each kernel version,
only the version/hash for the target kernel are available.
This cause a missing hash error (and wrong kernel version) for
bpf-headers when a testing kernel version is used for the current target.
Fix this error by manually including the kernel version/hash file for the
specific kernel version requested.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add a package for util-linux' ipcs command, to show information about
System V inter-process communication facilities.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
ZTE MF286 is an indoor LTE category 6 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.
Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: GD5F1G04UBYIG 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9882 2x2 MIMO 802.11ac radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN: MDM9230-based category 6 internal LTE modem in extended
mini-PCIE form factor, with 3 internal antennas and 2 external antenna
connections, single mini-SIM slot. Modem model identified as MF270,
- FXS: one external ATA port (handled entirely by modem part) with two
physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
Signal state) handled entirely by modem. 4 link status LEDs handled by
the switch on the backside.
- Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and
monitoring handled by modem.
- Label MAC device: eth0
Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.
Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.
STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
version before installation, to have built-in modem at the latest firmware
version.
STEP 1: gaining root shell:
Method 1:
This works if busybox has telnetd compiled in the binary.
If this does not work, try method 2.
Using well-known exploit to start telnetd on your router - works
only if Busybox on stock firmware has telnetd included:
- Open stock firmware web interface
- Navigate to "URL filtering" section by going to "Advanced settings",
then "Firewall" and finally "URL filter".
- Add an entry ending with "&&telnetd&&", for example
"http://hostname/&&telnetd&&".
- telnetd will immediately listen on port 4719.
- After connecting to telnetd use "admin/admin" as credentials.
Method 2:
This works if busybox does not have telnetd compiled in. Notably, this
is the case in DNA.fi firmware.
If this does not work, try method 3.
- Set IP of your computer to 192.168.1.22.
- Have a TFTP server running at that address
- Download MIPS build of busybox including telnetd, for example from:
https://busybox.net/downloads/binaries/1.21.1/busybox-mips
and put it in it's root directory. Rename it as "telnetd".
- As previously, login to router's web UI and navigate to "URL
filtering"
- Using "Inspect" feature, extend "maxlength" property of the input
field named "addURLFilter", so it looks like this:
<input type="text" name="addURLFilter" id="addURLFilter" maxlength="332"
class="required form-control">
- Stay on the page - do not navigate anywhere
- Enter "http://aa&zte_debug.sh 192.168.1.22 telnetd" as a filter.
- Save the settings. This will download the telnetd binary over tftp and
execute it. You should be able to log in at port 23, using
"admin/admin" as credentials.
Method 3:
If the above doesn't work, use the serial console - it exposes root shell
directly without need for login. Some stock firmwares, notably one from
finnish DNA operator lack telnetd in their builds.
STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.
Method 1: after booting OpenWrt initramfs image via TFTP:
PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION.
- Dump stock firmware located on stock kernel and ubi partitions:
ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
ssh root@192.168.1.1: cat /dev/mtd8 > mtd8_ubi.bin
And keep them in a safe place, should a restore be needed in future.
Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:
cat /proc/mtd
It should show the following:
mtd0: 00080000 00010000 "uboot"
mtd1: 00020000 00010000 "uboot-env"
mtd2: 00140000 00020000 "fota-flag"
mtd3: 00140000 00020000 "caldata"
mtd4: 00140000 00020000 "mac"
mtd5: 00600000 00020000 "cfg-param"
mtd6: 00140000 00020000 "oops"
mtd7: 00800000 00020000 "web"
mtd8: 00300000 00020000 "kernel"
mtd9: 01f00000 00020000 "rootfs"
mtd10: 01900000 00020000 "data"
mtd11: 03200000 00020000 "fota"
Differences might indicate that this is NOT a vanilla MF286 device but
one of its later derivatives.
- Copy over all MTD partitions, for example by executing the following:
for i in 0 1 2 3 4 5 6 7 8 9 10 11; do cat /dev/mtd$i > \
/var/usb_disk/mtd$i; done
- If the count of MTD partitions is different, this might indicate that
this is not a standard MF286 device, but one of its later derivatives.
- (optionally) rename the files according to MTD partition names from
/proc/mtd
- Unmount the filesystem:
umount /var/usb_disk; sync
and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
firmware. This is especially important, because stock firmware for
this device is not available officially, and is usually customized by
the mobile providers.
STEP 3: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.1.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.1.22
setenv ipaddr 192.168.1.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
Method 2: using initramfs image as temporary boot kernel
This exploits the fact, that kernel and rootfs MTD devices are
consecutive on NAND flash, so from within stock image, an initramfs can
be written to this area and booted by U-boot on next reboot, because it
uses "nboot" command which isn't limited by kernel partition size.
- Download the initramfs-kernel.bin image
- Split the image into two parts on 3MB partition size boundary, which
is the size of kernel partition. Pad the output of second file to
eraseblock size:
dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
bs=128k count=24 \
of=openwrt-ath79-zte_mf286-intermediate-kernel.bin
dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
bs=128k skip=24 conv=sync \
of=openwrt-ath79-zte_mf286-intermediate-rootfs.bin
- Copy over /usr/bin/flash_eraseall and /usr/bin/nandwrite utilities to
/tmp. This is CRITICAL for installation, as erasing rootfs will cut
you off from those tools on flash!
- After backing up the previous MTD contents, write the images to the
respective MTD devices:
/tmp/flash_eraseall /dev/<kernel-mtd>
/tmp/nandwrite /dev/<kernel-mtd> \
/var/usb_disk/openwrt-ath79-zte_mf286-intermediate-kernel.bin
/tmp/flash_eraseall /dev/<kernel-mtd>
/tmp/nandwrite /dev/<rootfs-mtd> \
/var/usb_disk/openwrt-ath79-zte_mf286-intermediate-rootfs.bin
- Ensure that no bad blocks were present on the devices while writing.
If they were present, you may need to vary the split between
kernel and rootfs parts, so U-boot reads a valid uImage after skipping
the bad blocks. If it fails, you will be left with method 3 (below).
- If write is OK, reboot the device, it will reboot to OpenWrt
initramfs:
reboot -f
- After rebooting, SSH into the device and use sysupgrade to perform
proper installation.
Method 3: using built-in TFTP recovery (LAST RESORT):
- With that method, ensure you have complete backup of system's NAND
flash first. It involves deliberately erasing the kernel.
- Download "-initramfs-kernel.bin" image for the device.
- Prepare the recovery image by prepending 8MB of zeroes to the image,
and name it root_uImage:
dd if=/dev/zero of=padding.bin bs=8M count=1
cat padding.bin openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin >
root_uImage
- Set up a TFTP server at 192.0.0.1/8. Router will use random address
from that range.
- Put the previously generated "root_uImage" into TFTP server root
directory.
- Deliberately erase "kernel" partition" using stock firmware after
taking backup. THIS IS POINT OF NO RETURN.
- Restart the device. U-boot will attempt flashing the recovery
initramfs image, which will let you perform actual installation using
sysupgrade. This might take a considerable time, sometimes the router
doesn't establish Ethernet link properly right after booting. Be
patient.
- After U-boot finishes flashing, the LEDs of switch ports will all
light up. At this moment, perform power-on reset, and wait for OpenWrt
initramfs to finish booting. Then proceed to actual installation.
STEP 4: Actual installation:
- scp the sysupgrade image to the device:
scp openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
STEP 5: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth '<auth>' # As required, usually 'none'
option pincode '<pin>' # If required by SIM
option apn '<apn>' # As required by ISP
option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'
For example, the following works for most polish ISPs
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth 'none'
option apn 'internet'
option pdptype 'ipv4'
If you have build with LuCI, installing luci-proto-qmi helps with this
task.
Restoring the stock firmware:
Preparation:
If you took your backup using stock firmware, you will need to
reassemble the partitions into images to be restored onto the flash. The
layout might differ from ISP to ISP, this example is based on generic stock
firmware.
The only partitions you really care about are "web", "kernel", and
"rootfs". For easy padding and possibly restoring configuration, you can
concatenate most of them into images written into "ubi" meta-partition
in OpenWrt. To do so, execute something like:
cat mtd5_cfg-param.bin mtd6-oops.bin mtd7-web.bin mtd9-rootfs.bin > \
mtd8-ubi_restore.bin
You can skip the "fota" partition altogether,
it is used only for stock firmware update purposes and can be overwritten
safely anyway. The same is true for "data" partition which on my device
was found to be unused at all. Restoring mtd5_cfg-param.bin will restore
the stock firmware configuration you had before.
Method 1: Using initramfs:
- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Look up the kernel and ubi partitions in /proc/mtd
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
(scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
mtd write <kernel_mtd> mtd4_kernel.bin
rm mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
restore them individually. Otherwise you might run out of space in
tmpfs:
(scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin
rm mtd3_ubiconcat0.bin
(scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin
rm mtd5_ubiconcat1.bin
- If the write was correct, force a device reboot with
reboot -f
Method 2: Using live OpenWrt system (NOT RECOMMENDED):
- Prepare a USB flash drive contatining MTD backup files
- Ensure you have kmod-usb-storage and filesystem driver installed for
your drive
- Mount your flash drive
mkdir /tmp/usb
mount /dev/sda1 /tmp/usb
- Remount your UBI volume at /overlay to R/O
mount -o remount,ro /overlay
- Write back the kernel and ubi partitions from USB drive
cd /tmp/usb
mtd write mtd4_kernel.bin /dev/<kernel_mtd>
mtd write mtd8_ubi.bin /dev/<kernel_ubi>
- If everything went well, force a device reboot with
reboot -f
Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota"
MTD partition which may be safely erased after reboot anyway.
Method 3: using built-in TFTP recovery (LAST RESORT):
- Assemble a recovery rootfs image from backup of stock partitions by
concatenating "web", "kernel", "rootfs" images dumped from the device,
as "root_uImage"
- Use it in place of "root_uImage" recovery initramfs image as in the
TFTP pre-installation method.
Quirks and known issues
- Kernel partition size is increased to 4MB compared to stock 3MB, to
accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
image is at 2.5MB which is dangerously close to the limit. This has no
effect on booting the system - but keep that in mind when reassembling
an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
you used before in stock firmware first. If you need to change it,
please use protocok '3g' to establish connection once, or use the
following command to change APN (and optionally IP type) manually:
echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the green debug LED hidden
inside the case. All other LEDs are controlled by modem, on which the
router part has some influence only on Wi-Fi LED.
- Wi-Fi LED currently doesn't work while under OpenWrt, despite having
correct GPIO mapping. All other LEDs are controlled by modem,
including this one in stock firmware. GPIO19, mapped there only acts
as a gate, while the actual signal source seems to be 5GHz Wi-Fi
radio, however it seems it is not the LED exposed by ath10k as
ath10k-phy0.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
reset of whole board, not only the modem. It is attached to
gpio-restart driver, to restart the modem on reboot as well, to ensure
QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
for OpenWrt operation at all - have fun lurking around.
- MAC address shift for 5GHz Wi-Fi used in stock firmware is
0x320000000000, which is impossible to encode in the device tree, so I
took the liberty of using MAC address increment of 1 for it, to ensure
different BSSID for both Wi-Fi interfaces.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
ZTE MF286D is a LTE router with four gigabit ethernet ports
and integrated QMI mPCIE modem.
Hardware specification:
- CPU: IPQ4019
- RAM: 256MB
- Flash: NAND 128MB + NOR 2MB
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2
- LTE: mPCIe cat 12 card (Modem chipset MDM9250)
- LAN: 4 Gigabit Ports
- USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem)
- Serial console: X8 connector 115200 8n1
Known issues:
- Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs
are driven by cpu.
- Wifi LED is triggered by phy0tpt only
- No VoIP support
- LAN1/WAN port is configured as WAN
- ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN
and WLAN0/1
Opening the case:
1. Take of battery lid (no battery support for this model, battery cage
is dummy).
2. Unscrew screw placed behind battery lid.
3. Take off back cover. It attached with multiple plastic clamps.
4. Unscrew four more screws hidden behind back case.
5. Remove front panel from blue chassis. There are more plastic
clamps.
6. Unscrew two boards, which secures the PCB in the chassis.
7. Extract board from blue chassis.
Console connection (X8 connector):
1. Parameters: 115200 8N1
2. Pin description: (from closest pin to X8 descriptor to farthest)
- VCC (3.3V)
- TX
- RX
- GND
Install Instructions:
Serial + initramfs:
1. Place OpenWrt initramfs image for the device on a TFTP in
the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to X8 connector.
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:
setenv serverip 192.168.1.3
setenv ipaddr 192.168.1.72
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert
to stock.
6. Login via ssh or serial and remove stock partitions:
ubiattach -m 9
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. Install image via "sysupgrade -n".
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cosmetic changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kalle Valo ath10k-firmware repository no longer provides the
legacy board.bin files for the qca99x0 chips. Instead he
copied over the codeaurora version and add more board files.
In the future, this board-2.bin should find its way to
linux-firmware.git, which would allow us to remove the
extra download code completely.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
this should have been removed together with linux 5.4 APM821XX
support. Currently, this didn't hurt or broke something. But it
will in the next stable kernel release.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The SDK does not ship the generic platform files. Use relative path for
GENERIC_PLATFORM_DIR to make it work. This points it at the files from
the feed directory instead of the base SDK path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All devices which used this package migrated to the kernel GPIO-line
watchdog driver and configure it over their DT.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This solves issue with DDR training on Turris Omnia.
Log:
******** DRAM initialization Failed (res 0x1) ********
DDR3 Training Sequence - FAILED
ERROR ### Please RESET the board ###
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Now that we can have both legacy and nft iptables variants
installed at the same time, install the legacy symlinks
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
As nftables is now the default, ip(6)tables-nft gets higher priority
The removed symlinks ("$(CP)" line) will now be installed by the
ALTERNATIVES mechanism
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
according to iptables-nft man page,
"These tools use the libxtables framework extensions and hook to the nf_tables
kernel subsystem using the nft_compat module."
This means that to work, iptables-nft needs the same modules as
iptables legacy except the ip(6)table-{filter,mangle,nat,raw}
ip_tables, ip6tables.
When those modules are loaded iptables-nft-save output contains
"# Warning: iptables-legacy tables present, use iptables-legacy-save to see them"
But as long as it's empty it should not be a problem.
To have nft properly display the rules created by ip(6)tables-nft we need
all iptables targets and matches to be built as extension and not built-in
(/usr/lib/iptables/libip(6)t_*.so)
When switching a package to iptables-nft, you need to keep the
iptables-mod-* dependencies
This patch does minimal changes:
- remove the direct iptables-nft -> iptables dependency
- and more important add nft-compat dependency
The rule
iptables-nft -A OUTPUT -d 8.8.8.8 -m comment --comment "aaa" -j REJECT
becomes
table ip filter {
chain OUTPUT {
type filter hook output priority filter; policy accept;
ip daddr 8.8.8.8 # xt_comment counter packets 0 bytes 0 # xt_REJECT
}
}
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Add option to compile kmod-vrf, support for Virtual Routing and
Forwarding (Lite).
This module depends on NET_L3_MASTER_DEV, which is a boolean kernel
option, so we need to create a configuration option also for this, and
make kmod-vrf depend on it.
Signed-off-by: Marek Behún <kabel@kernel.org>
The sizes of the ipk changed on MIPS 24Kc like this:
13281 uboot-envtools_2021.01-54_mips_24kc.ipk
13308 uboot-envtools_2022.01-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sizes of the ipk changed on MIPS 24Kc like this:
11248 libcap_2.51-1_mips_24kc.ipk
14461 libcap_2.63-1_mips_24kc.ipk
18864 libcap-bin_2.51-1_mips_24kc.ipk
20576 libcap-bin_2.63-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This release fixes two security mount(8) and umount(8) issues:
CVE-2021-3996
Improper UID check in libmount allows an unprivileged user to unmount FUSE
filesystems of users with similar UID.
CVE-2021-3995
This issue is related to parsing the /proc/self/mountinfo file allows an
unprivileged user to unmount other user's filesystems that are either
world-writable themselves or mounted in a world-writable directory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The man page of the raw tool does not build because the disk-utils/raw.8
file is missing. It looks like it should be in the tar.xz file we
download, but it is missing.
We do not package the raw tool, so this is not a problem.
This fixes the following build error:
No rule to make target 'disk-utils/raw.8', needed by 'all-am'. Stop.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sizes of the ipk changed on MIPS 24Kc like this:
289764 strace_5.14-1_mips_24kc.ipk
310899 strace_5.16-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
795f420 cmis: Rename CMIS parsing functions
369b43a cmis: Initialize CMIS memory map
da16288 cmis: Use memory map during parsing
6acaeb9 cmis: Consolidate code between IOCTL and netlink paths
d7d15f7 sff-8636: Rename SFF-8636 parsing functions
4230597 sff-8636: Initialize SFF-8636 memory map
b74c040 sff-8636: Use memory map during parsing
799572f sff-8636: Consolidate code between IOCTL and netlink paths
9fdf45c sff-8079: Split SFF-8079 parsing function
2ccda25 netlink: eeprom: Export a function to request an EEPROM page
86792db cmis: Request specific pages for parsing in netlink path
6e2b32a sff-8636: Request specific pages for parsing in netlink path
c2170d4 sff-8079: Request specific pages for parsing in netlink path
9538f38 netlink: eeprom: Defer page requests to individual parsers
664586e Merge branch 'review/next/module-mem-map' into master
50fdaec ethtool: Set mask correctly for dumping advertised FEC modes
c5e7133 cable-test: Fix premature process termination
73091cd sff-8636: Use an SFF-8636 specific define for maximum number of channels
837c166 sff-common: Move OFFSET_TO_U16_PTR() to common header file
8658852 cmis: Initialize Page 02h in memory map
27b42a9 cmis: Initialize Banked Page 11h in memory map
340d88e cmis: Parse and print diagnostic information
eae6a99 cmis: Print Module State and Fault Cause
82012f2 cmis: Print Module-Level Controls
d7b1007 sff-8636: Print Power set and Power override bits
429f2fc Merge branch 'review/cmis-diag' into master
32457a9 monitor: do not show duplicate options in help text
c01963e Release version 5.16.
The sizes of the ipk changed on MIPS 24Kc like this:
34317 ethtool_5.15-1_mips_24kc.ipk
34311 ethtool_5.16-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following security problems:
* Zeroize several intermediate variables used to calculate the expected
value when verifying a MAC or AEAD tag. This hardens the library in
case the value leaks through a memory disclosure vulnerability. For
example, a memory disclosure vulnerability could have allowed a
man-in-the-middle to inject fake ciphertext into a DTLS connection.
* Fix a double-free that happened after mbedtls_ssl_set_session() or
mbedtls_ssl_get_session() failed with MBEDTLS_ERR_SSL_ALLOC_FAILED
(out of memory). After that, calling mbedtls_ssl_session_free()
and mbedtls_ssl_free() would cause an internal session buffer to
be free()'d twice. CVE-2021-44732
The sizes of the ipk changed on MIPS 24Kc like this:
182454 libmbedtls12_2.16.11-2_mips_24kc.ipk
182742 libmbedtls12_2.16.12-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a minor corrective release over GDB 11.1, fixing the following issues:
* PR sim/28302 (gdb fails to build with glibc 2.34)
* PR build/28318 (std::thread support configure check does not use CXX_DIALECT)
* PR gdb/28405 (arm-none-eabi: internal-error: ptid_t remote_target::select_thread_for_ambiguous_stop_reply(const target_waitstatus*): Assertion `first_resumed_thread != nullptr' failed)
* PR tui/28483 ([gdb/tui] breakpoint creation not displayed)
* PR build/28555 (uclibc compile failure since commit 4655f8509fd44e6efabefa373650d9982ff37fd6)
* PR rust/28637 (Rust characters will be encoded using DW_ATE_UTF)
* PR gdb/28758 (GDB 11 doesn't work correctly on binaries with a SHT_RELR (.relr.dyn) section)
* PR gdb/28785 (Support SHT_RELR (.relr.dyn) section)
The sizes of the ipk changed on mips 24Kc like this:
2285775 gdb_11.1-3_mips_24kc.ipk
2287441 gdb_11.2-4_mips_24kc.ipk
191828 gdbserver_11.1-3_mips_24kc.ipk
191811 gdbserver_11.2-4_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the most recent supported firmware file for Intel Wi-Fi 6E AX210
wireless chip. The API version 67 is not yet supported by the driver.
Additional PNVM file is required since API version 62.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Just use 'start' action which will have the desired effect instead of
trying to introduce a 'start_file' action which didn't work that way
because procd jshn magic would have to wrap around it.
Fixes: 88baf6ce2c ("ubox: only start log to file when filesystem has been mounted")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
From: Peter Lundkvist <peter.lundkvist@gmail.com>
This fixes the make_syscall_h.sh script to recognize both
__NR_Linux, used by mips, and __NR_SYSCALL_BASE and
__ARM_NR_BASE used by arm.
Run-tested on arm (ipq806x) and mips (ath79), both with glibc.
Compile-tested and checked resulting syscall_names.h file wuth
glibc: aarch64, powerpc, x86_64, i486
musl: arm, mips
Fixes: FS#4194, FS#4195
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If log_file is on an filesystem mounted using /etc/config/fstab we have
to wait for that to happen before starting the logread process.
Inhibit the start of the file-writer process and use a mount trigger to
fire it up once the filesystem actually becomes available.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow init scripts to trigger free-form actions by exposing
procd_add_action_mount_trigger.
Clean up mount trigger wrappers while at it to reduce code duplication.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The arc700 target is not booting up since some time, see here:
https://github.com/foss-for-synopsys-dwc-arc-processors/toolchain/issues/400
It looks like there is a problem in the toolchain when using glibc.
Currently no one is working on fixing this problem, remove the target
instead. This target also does not have many users we are aware of.
If someone wants to have this target back, feel free to add a fixed
version of this target again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
bpftool will enabled libbfd and libopcodes which gets picked up by perf
as libraries to link against. Add those missing dependencies when either
of these packages are enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
nf-nathelper-extra and nf-conntrack-netlink had iptables related
dependencies, yet, when looking for the respective kernel symbols and
checking it's dependencies it was confirmed that iptables wasn't
required and that these were either it's own moodule or tool independent
(nftables or iptables).
Correct these and make sure no unneeded extras are pulled in.
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Brings bootmenu and production/recovery dual-boot scheme like on
the BPi-R2, BPi-R64, E8450 and UniFi 6 LR.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The ucode VM always passes 64bit integer values to sprintf implementation
while the `%d` format expects 32bit integers on 32bit platforms, leading
to incorrect formatting results.
Temporarily solve the issue by casting the numeric argument to int until
a more thorough fix arrives with the next update.
Fixes: FS#4234
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This removes -static compile option. The -static option tells GCC to
link this statically with the libc, which we do not want in OpenWrt. We
want to link everything dynamically to the libc. This fixes a compile
problem with glibc.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the nohostroute option as available for gre and wg tunnels to
allow the user to prevent explicit creation of a route to the peer
address.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 18-24V passive POE (mode B)
+ used as WAN interface
- eth1
+ builtin switch port 4
+ used as LAN interface
* 12-24V 1A DC
* external antenna
The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Changes from 2.1.3 to 2.1.4:
Features:
- ubiscan debugging and statistics utility
Fixes:
- Some mtd-tests erroneously using sub-pages instead of the full page size
- Buffer overrun in fectest
- Missing jffs2 kernel header in the last release, leading to build
failures on some systems.
Changes from 2.1.2 to 2.1.3:
Features:
flashcp: Add new function that copy only different blocks
flash_erase: Add flash erase chip
Add flash_otp_erase
Add an ubifs mount helper
Add nandflipbits tool
Fixes:
mkfs.ubifs: Fix runtime assertions when running without crypto
mtd-utils: Use AC_SYS_LARGEFILE
Fix test binary installation
libmtd: avoid divide by zero
ubihealthd: fix UBIFS build dependency
mkfs.ubifs: remove OPENSSL_no_config()
misc-utils: Add fectest to build system
mkfs.ubifs: Fix build with SELinux
Fix typos found by Debian's lintian tool
Fix jffs2 build if zlib or lzo headers are not in default paths
Signed-off-by: Nick Hainke <vincent@systemli.org>
x86, mt7623 and others buildbot failed due to:
|Package kmod-hwmon-nct7802 is missing dependencies for the following libraries:
|regmap-core.ko
|regmap-i2c.ko
Fixes: 1ed50b92d1 ("package: kernel: add driver module for NCT7802Y")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit add package with hwmon-nct7802 module.
This driver implements support for the Nuvoton NCT7802Y hardware monitoring
chip. NCT7802Y supports 6 temperature sensors, 5 voltage sensors, and 3 fan
speed sensors.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(fixed c&p'ed module description)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4019
CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
DRAM: 256 MB
NAND: 128 MiB Macronix MX30LF1G18AC
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN)
USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4
INPUT: 1x WPS, 1x Reset
LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN
This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed
with an intermediary initramfs image, the jffs2 ubi volume deleted, and
then finally a sysupgrade with the final image performed.
Signed-off-by: Joshua Roys <roysjosh@gmail.com>
(added ALT0)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
OpenWrt plans to move over to firewall4 which uses nftables under the
hood. To allow a smooth migration the package `iptables-nft` offer a
transparent wrapper to apply iptables rules to nftables.
Without the config option for nftables the package isn't installed and
therefore can't be tested. This commit enabled it and therefore provides
the wrapper.
The size of the iptables package increases from 25436 to 26500 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
ca6c35c uxc: usage message cosmetics
e083dd4 uxc: fix two minor issues reported by Coverity
35dfbff procd: jail/cgroups: correctly enable "rdma" when requested
3b3ac64 procd: mount /dev with noexec
ac2b8b3 procd: clean up /dev/pts mounts
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
0f16ea5 options.c: add DSCP code LE Least Effort
24ba465 firewall3: remove redundant syn check
df1306a firewall3: fix locking issue
3624c37 firewall3: support table load on access on Linux 5.15+
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ 10/100 Mbps Ethernet
+ builtin switch port 1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
db7fb64 libopkg: pkg_hash: prefer to-be-installed packages
2edcfad libopkg: set 'const' attribute for argv
This should fix the ImageBuilder problems people are having since we
introduced the 'uci-firewall' providers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
9a509d4 ruleset.uc: consolidate ip and ip6 offload
21f311d ruleset.uc: don't trim newline before comment sign
f121383 tests: enable flow offloading in tests
550df40 tests: add test for unknown defaults option
47c5a5b tests: add test for deprecated rule option
69a89d6 tests: add test for unknown rule option
07579df fw4.uc: handle interface zone option
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Almost all targets have the fixed-phy feature built into the kernel.
One big exception is x86. This caused a problem with the upcoming
LAN78xx usb driver. Hence this patch breaks out the fixed-phy from
of_mdio (which didn't include the .ko) and puts into a separate
module.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
phy drivers for Microchip's LAN88xx PHYs.
This is needed for the "LAN7801" variant
of the upstream lan78xx usb ethernet driver.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
libdw depends on libfts.so when building with the musl-libc library, add
this missing dependency.
Fixes: 6835ea13f0 ("elfutils: update to 0.186")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Linux upstream commit 9370f2d05a
add load firmware file through request_firmware,this affect the
nanopi r2s and some USB adapters in kernel 5.10 with this error:
'r8152 4-1:1.0: unable to load firmware patch rtl_nic/rtl8153b-2.fw'
This patch split the USB NIC firmware files from r8169 firmware,
and adds r8152-firmware to r8152 driver.
Add kmod-usb-net-cdc-ncm to support RTL8156A and RTL8156B 2.5G ethernet
adapters supported since v5.13-rc1.
195aae321c
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Update busybox to 1.35.0
* refresh patches
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in : change at "Options common to all shells" the symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
session tickets are a feature of TLSv1.2 and require less memory
and overhead on the server than does managing a session cache
Building mbedtls with support for session tickets will allow the
feature to be used with lighttpd-1.4.56 and later.
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0
This is another MT7621 device, very similar to other Linksys EA7300
series devices.
Installation:
Upload the generated factory.bin image via the stock web firmware
updater.
Reverting to factory firmware:
Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking. Hard-resetting this device three (3) times will
put the device in failsafe (default) mode. At this point, flash the
OEM image to itself and reboot. This puts the router back into the 'B'
image and allows for a firmware upgrade.
Troubleshooting:
If the firmware will not boot, first restore the factory as described
above. This will then allow the factory.bin update to be applied
properly.
Signed-off-by: Nick McKinney <nick@ndmckinney.net>
CHECK_RUN_DIR=0 must be a part of MAKE_FLAGS, not MAKE_VARS, otherwise
it is not possible to compile mdadm on host without /run dir.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
glibc version 2.34 does not provide versioned shared libraries any more,
it only provides shared libraries using the ABI version. Do not try to
copy them any more.
The functions from libpthread and librt were integrated into the main
binary, the libpthread.so and librt.so are only used for backwards
compatibility any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Provide uci-firewall via PROVIDES in both firewall and firewall4. This
will allow us to change the dependency of luci-app-firewall to
uci-firewall, making it possible to use it with either implementation.
Move CONFLICTS from firewall4 to firewall, to solve this recursive
dependency problem:
tmp/.config-package.in:307:error: recursive dependency detected!
tmp/.config-package.in:307: symbol PACKAGE_firewall is selected by PACKAGE_firewall4
tmp/.config-package.in:328: symbol PACKAGE_firewall4 depends on PACKAGE_firewall
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
4ead2a6 treewide: move executables to /sbin
9ebc2f4 fw4.uc: filter duplicates in fw4.set
85b74f3 treewide: support flow offloading
be3b4e6 treewide: support hardware flow offloading
38889b7 treewide: support set timeout
31c7550 fw4.uc: do not skip defaults with invalid option
334a127 fw4.uc: introduce DEPRECATED flag
7a0d38f fw4.uc: add _name as deprecated option
5e7ad3b fw4.uc: don't fail on unknown options
be5f4e3 fw4.uc: allow use of cidr in ipsets
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
The limitation of not being able to use iptables and nft nat at the same
time exists only in kernels before 4.18.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
ARC4 was used for WEP, which is not secure anymore. Therefor it is
disabled in the driver, but the code is not removed for now.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The lantiq AES hardware does not support the gcm algorithm. But it
can be implemented in the driver as a combination of the aes_ctr
algorithm and the xor plus gfmul operations for the hashing.
Due to the wrapping of the several algorithms and the inefficient
16 byte block by 16 byte block invokation in the kernel
implementations, this driver is about 3 times faster for the larger
block sizes.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
After adding xts and cbcmac the aes algorithm source had three sections
for setting the aes key to the hardware which are identical.
Method aes_set_key_hw was created which is now called from within the
spinlock secured control sections in methods ifx_deu_aes, ifx_deu_aes_xts
and aes_cbcmac_final_impl and reduces the size of ifxmips_aes.c.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Since commit 53b6783 hostapd is using the kernel api which includes the
cbcmac-aes shash algorithm. The kernels implementation is a wrapper around
the aes encryption algorithm, which encrypts block (16 bytes) by block.
When the ltq-deu driver is present, it uses hardware aes, but every 16 byte
encrypt requires setting the key. This is very inefficient and is a huge
overhead. Since the cbcmac-aes is simply a hash that uses the cbc aes
algorithm starting with an iv set to x'00' with an optional ecb aes
encryption of a possible last incomplete block that is padded with the
positional bytes of the last cbc encrypted block, this algorithm is now
added to the driver. Most of the code is derived from md5-hmac and
tailored for aes. Tested with the kernels crypto testmgr including extra
tests against the kernels generic ccm module implementation.
This patch also fixes the overallocation in the aes_ctx that is caused
by using u32 instead of u8 for the aes keys.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
