Commit Graph

25583 Commits

Author SHA1 Message Date
Wenli Looi
c32008a37b ath79: add partial support for Netgear EX7300v2
Hardware
--------
SoC: QCN5502
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 1 gigabit port
Wireless No1: QCN5502 on-chip 2.4GHz 4x4
Wireless No2: QCA9984 pcie 5GHz 4x4
USB: none

Installation
------------
Flash the factory image using the stock web interface or TFTP the
factory image to the bootloader.

What works
----------
- LEDs
- Ethernet port
- 5GHz wifi (QCA9984 pcie)

What doesn't work
-----------------
- 2.4GHz wifi (QCN5502 on-chip)
  (I was not able to make this work, probably because ath9k requires
  some changes to support QCN5502.)

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2022-02-07 00:03:27 +01:00
Wenli Looi
6ede645282 ath79: add support for booting QCN5502 SoC
Based on wikidevi, QCN5502 is a "Dragonfly" like QCA9561 and QCA9563.
Treating it as QCA956x seems to work.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2022-02-07 00:03:27 +01:00
Saiful Islam
43ec6d64bb ath79: add support for TP-Link TL-WR841HP v2
Specifications:
- AR9344 SoC, 8 MB nor flash, 64 MB DDR2 RAM
- 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps
- 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100
- 1x WAN, 4x LAN, Wifi, PWR, WPS, SYSTEM Leds
- Reset/WPS button
- Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1

MAC addresses as verified by OEM firmware:

vendor   OpenWrt   address
LAN      eth0      label
WAN      eth1      label + 1
WLAN     phy0      label

The label MAC address was found in u-boot 0x1fc00.

Installation:
To install openwrt,
- set the device's SSID to each of the following lines,
  making sure to include the backticks.
- set the ssid and click save between each line.

`echo "httpd -k"> /tmp/s`
`echo "sleep 10">> /tmp/s`
`echo "httpd -r&">> /tmp/s`
`echo "sleep 10">> /tmp/s`
`echo "httpd -k">> /tmp/s`
`echo "sleep 10">> /tmp/s`
`echo "httpd -f">> /tmp/s`
`sh /tmp/s`

- Now, wait 60 sec.
- After the reboot sequence, the router may have fallen back to
  its default IP address with the default credentials (admin:admin).
- Log in to the web interface and go the the firmware upload page.
  Select "openwrt-ath79-generic-tplink_tl-wr841hp-v2-squashfs-factory.bin"
  and you're done : the system now accepts the openwrt.

Forum support topic:
https://forum.openwrt.org/t/support-for-tplink-tl-wr841hp-v2/69445/

Signed-off-by: Saiful Islam <si87868@gmail.com>
2022-02-07 00:03:27 +01:00
Rosen Penev
8cfce165a7 target/linux: replace egrep with grep -E
egrep is deprecated and replaced by grep -E. The latter is used
throughout the tree.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-02-07 00:03:27 +01:00
Christian Lamparter
f6a01d7f5c ipq806x: convert TP-Link Archer VR2600v to denx,uimage
The recent device-tree modification that added pre-cal
nvmem-cells pushed the device's kernel+dtb over the
allotted 3072k KERNEL_SIZE.

> WARNING: Image file tplink_vr2600v-uImage is too big: 3147214 > 3145728

There was a previous kernel partition size upgrade:
commit 0c967d92b3 ("ipq806x: increase kernel partition size for the TP-Link Archer VR2600v")
It has been seemingly upgraded from a 2048k KERNEL_SIZE in the past.
The commit talks about using the MTD_SPLIT_TPLINK_FW. But looking at
the image make recipe, there is no code that adds a TPLINK header.
So instead the board will use "denx,umimage". This requires
MTD_SPLIT_UIMAGE_FW, but this is present thanks to some NEC devices.

(Maybe the MTD_CONFIG_ARGS can be removed as well? But it could be
there because of the padding at the beginning. This needs testing.)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-06 17:11:20 +01:00
Hauke Mehrtens
1b311aab31 Revert "kernel: backport MediaTek Ethernet PHY driver"
This reverts commit 8b4cba53a9.

This broke the mt7530 on Linksys e8450 (mt7622) for me.
[    1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL
[    1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0
[    1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL
[    1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1
[    1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL
[    1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2
[    1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL
[    1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3
[    1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL
[    1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-02-05 19:13:19 +01:00
Hauke Mehrtens
781f2f7300 Revert "kernel: backport MT7530 IRQ support"
This reverts commit 3f4301e123.

This broke the mt7530 on Linksys e8450 (mt7622) for me.
[    1.300554] mt7530 mdio-bus:00: no interrupt support

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-02-05 19:13:15 +01:00
DENG Qingfang
3f4301e123 kernel: backport MT7530 IRQ support
Support MT7530 PHY link change interrupts, and enable for MT7621.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-05 17:46:59 +02:00
DENG Qingfang
8b4cba53a9 kernel: backport MediaTek Ethernet PHY driver
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530.
Fix some link up/down issues.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-05 17:46:59 +02:00
DENG Qingfang
d5f4472509 kernel: backport MT7530 MDB operations
Use hardware to forward multicast traffic instead of trapping to the
host.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-05 17:46:59 +02:00
DENG Qingfang
ee6ba216d8 kernel: backport MT7530 VLAN fix
Fix FDB learning bugs when VLAN filtering is enabled.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-05 17:46:59 +02:00
DENG Qingfang
4834565bb4 kernel: backport MT7530 ageing time support
Allow setting ageing time from 1 to 1,048,576 seconds.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-05 17:46:59 +02:00
DENG Qingfang
637a3aaa6f kernel: backport MediaTek jumbo frame support
Allow MTU up to 2026 on mediatek, ramips/mt7621 targets.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-05 17:46:59 +02:00
Paul Spooren
7a1ce08bdb octeontx: switch to 5.10 Kernel
Tested by multiple users and seems to work fine.

Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-02-05 14:39:20 +01:00
Lech Perczak
8c78a13bfc ath79: support ZTE MF286
ZTE MF286 is an indoor LTE category 6 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.

Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: GD5F1G04UBYIG 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9882 2x2 MIMO 802.11ac radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN: MDM9230-based category 6 internal LTE modem in extended
  mini-PCIE form factor, with 3 internal antennas and 2 external antenna
  connections, single mini-SIM slot. Modem model identified as MF270,
- FXS: one external ATA port (handled entirely by modem part) with two
  physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
  Signal state) handled entirely by modem. 4 link status LEDs handled by
  the switch on the backside.
- Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and
  monitoring handled by modem.
- Label MAC device: eth0

Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
  converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.

Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.

STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
version before installation, to have built-in modem at the latest firmware
version.

STEP 1: gaining root shell:

Method 1:
This works if busybox has telnetd compiled in the binary.
If this does not work, try method 2.

Using well-known exploit to start telnetd on your router - works
only if Busybox on stock firmware has telnetd included:
- Open stock firmware web interface
- Navigate to "URL filtering" section by going to "Advanced settings",
  then "Firewall" and finally "URL filter".
- Add an entry ending with "&&telnetd&&", for example
  "http://hostname/&&telnetd&&".
- telnetd will immediately listen on port 4719.
- After connecting to telnetd use "admin/admin" as credentials.

Method 2:
This works if busybox does not have telnetd compiled in. Notably, this
is the case in DNA.fi firmware.
If this does not work, try method 3.

- Set IP of your computer to 192.168.1.22.
- Have a TFTP server running at that address
- Download MIPS build of busybox including telnetd, for example from:
  https://busybox.net/downloads/binaries/1.21.1/busybox-mips
  and put it in it's root directory. Rename it as "telnetd".
- As previously, login to router's web UI and navigate to "URL
  filtering"
- Using "Inspect" feature, extend "maxlength" property of the input
  field named "addURLFilter", so it looks like this:
  <input type="text" name="addURLFilter" id="addURLFilter" maxlength="332"
    class="required form-control">
- Stay on the page - do not navigate anywhere
- Enter "http://aa&zte_debug.sh 192.168.1.22 telnetd" as a filter.
- Save the settings. This will download the telnetd binary over tftp and
  execute it. You should be able to log in at port 23, using
  "admin/admin" as credentials.

Method 3:
If the above doesn't work, use the serial console - it exposes root shell
directly without need for login. Some stock firmwares, notably one from
finnish DNA operator lack telnetd in their builds.

STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.

Method 1: after booting OpenWrt initramfs image via TFTP:
PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION.
- Dump stock firmware located on stock kernel and ubi partitions:

  ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
  ssh root@192.168.1.1: cat /dev/mtd8 > mtd8_ubi.bin

And keep them in a safe place, should a restore be needed in future.

Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
  port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:

  cat /proc/mtd

  It should show the following:
  mtd0: 00080000 00010000 "uboot"
  mtd1: 00020000 00010000 "uboot-env"
  mtd2: 00140000 00020000 "fota-flag"
  mtd3: 00140000 00020000 "caldata"
  mtd4: 00140000 00020000 "mac"
  mtd5: 00600000 00020000 "cfg-param"
  mtd6: 00140000 00020000 "oops"
  mtd7: 00800000 00020000 "web"
  mtd8: 00300000 00020000 "kernel"
  mtd9: 01f00000 00020000 "rootfs"
  mtd10: 01900000 00020000 "data"
  mtd11: 03200000 00020000 "fota"

  Differences might indicate that this is NOT a vanilla MF286 device but
  one of its later derivatives.
- Copy over all MTD partitions, for example by executing the following:

  for i in 0 1 2 3 4 5 6 7 8 9 10 11; do cat /dev/mtd$i > \
  /var/usb_disk/mtd$i; done

- If the count of MTD partitions is different, this might indicate that
  this is not a standard MF286 device, but one of its later derivatives.
- (optionally) rename the files according to MTD partition names from
  /proc/mtd
- Unmount the filesystem:

  umount /var/usb_disk; sync

  and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
  firmware. This is especially important, because stock firmware for
  this device is not available officially, and is usually customized by
  the mobile providers.

STEP 3: Booting initramfs image:

Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
  set your computer's IP address as 192.168.1.22. This is the default
  expected by U-boot. You may wish to change that, and alter later
  commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:

  setenv serverip 192.168.1.22
  setenv ipaddr 192.168.1.1
  tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin
  bootm 0x81000000

  (Replace server IP and router IP as needed). There is no  emergency
  TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
  installation.

Method 2: using initramfs image as temporary boot kernel
This exploits the fact, that kernel and rootfs MTD devices are
consecutive on NAND flash, so from within stock image, an initramfs can
be written to this area and booted by U-boot on next reboot, because it
uses "nboot" command which isn't limited by kernel partition size.
- Download the initramfs-kernel.bin image
- Split the image into two parts on 3MB partition size boundary, which
  is the size of kernel partition. Pad the output of second file to
  eraseblock size:

  dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
  bs=128k count=24 \
  of=openwrt-ath79-zte_mf286-intermediate-kernel.bin

  dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
  bs=128k skip=24 conv=sync \
  of=openwrt-ath79-zte_mf286-intermediate-rootfs.bin

- Copy over /usr/bin/flash_eraseall and /usr/bin/nandwrite utilities to
  /tmp. This is CRITICAL for installation, as erasing rootfs will cut
  you off from those tools on flash!

- After backing up the previous MTD contents, write the images to the
  respective MTD devices:

  /tmp/flash_eraseall /dev/<kernel-mtd>

  /tmp/nandwrite /dev/<kernel-mtd> \
  /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-kernel.bin

  /tmp/flash_eraseall /dev/<kernel-mtd>

  /tmp/nandwrite /dev/<rootfs-mtd> \
  /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-rootfs.bin

- Ensure that no bad blocks were present on the devices while writing.
  If they were present, you may need to vary the split  between
  kernel and rootfs parts, so U-boot reads a valid uImage after skipping
  the bad blocks. If it fails, you will be left with method 3 (below).
- If write is OK, reboot the device, it will reboot to OpenWrt
  initramfs:

  reboot -f

- After rebooting, SSH into the device and use sysupgrade to perform
  proper installation.

Method 3: using built-in TFTP recovery (LAST RESORT):
- With that method, ensure you have complete backup of system's NAND
  flash first. It involves deliberately erasing the kernel.
- Download "-initramfs-kernel.bin" image for the device.
- Prepare the recovery image by prepending 8MB of zeroes to the image,
  and name it root_uImage:

  dd if=/dev/zero of=padding.bin bs=8M count=1

  cat padding.bin openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin >
  root_uImage

- Set up a TFTP server at 192.0.0.1/8. Router will use random address
  from that range.
- Put the previously generated "root_uImage" into TFTP server root
  directory.
- Deliberately erase "kernel" partition" using stock firmware after
  taking backup. THIS IS POINT OF NO RETURN.
- Restart the device. U-boot will attempt flashing the recovery
  initramfs image, which will let you perform actual installation using
  sysupgrade. This might take a considerable time, sometimes the router
  doesn't establish Ethernet link properly right after booting. Be
  patient.
- After U-boot finishes flashing, the LEDs of switch ports will all
  light up. At this moment, perform power-on reset, and wait for OpenWrt
  initramfs to finish booting. Then proceed to actual installation.

STEP 4: Actual installation:
- scp the sysupgrade image to the device:

  scp openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin \
  root@192.168.1.1:/tmp/

- ssh into the device and execute sysupgrade:

  sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin

- Wait for router to reboot to full OpenWrt.

STEP 5: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:

config interface 'wan'
        option proto 'qmi'
        option device '/dev/cdc-wdm0'
        option auth '<auth>' # As required, usually 'none'
        option pincode '<pin>' # If required by SIM
        option apn '<apn>' # As required by ISP
        option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'

For example, the following works for most polish ISPs
config interface 'wan'
        option proto 'qmi'
        option device '/dev/cdc-wdm0'
        option auth 'none'
        option apn 'internet'
        option pdptype 'ipv4'

If you have build with LuCI, installing luci-proto-qmi helps with this
task.

Restoring the stock firmware:

Preparation:
If you took your backup using stock firmware, you will need to
reassemble the partitions into images to be restored onto the flash. The
layout might differ from ISP to ISP, this example is based on generic stock
firmware.
The only partitions you really care about are "web", "kernel", and
"rootfs". For easy padding and possibly restoring configuration, you can
concatenate most of them into images written into "ubi" meta-partition
in OpenWrt. To do so, execute something like:

cat mtd5_cfg-param.bin mtd6-oops.bin mtd7-web.bin mtd9-rootfs.bin > \
mtd8-ubi_restore.bin

You can skip the "fota" partition altogether,
it is used only for stock firmware update purposes and can be overwritten
safely anyway. The same is true for "data" partition which on my device
was found to be unused at all. Restoring mtd5_cfg-param.bin will restore
the stock firmware configuration you had before.

Method 1: Using initramfs:
- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Look up the kernel and ubi partitions in /proc/mtd
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
  (scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
  mtd write <kernel_mtd> mtd4_kernel.bin
  rm mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
  restore them individually. Otherwise you might run out of space in
  tmpfs:

  (scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)

  mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin
  rm mtd3_ubiconcat0.bin

  (scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)

  mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin
  rm mtd5_ubiconcat1.bin

- If the write was correct, force a device reboot with

  reboot -f

Method 2: Using live OpenWrt system (NOT RECOMMENDED):
- Prepare a USB flash drive contatining MTD backup files
- Ensure you have kmod-usb-storage and filesystem driver installed for
  your drive
- Mount your flash drive

  mkdir /tmp/usb

  mount /dev/sda1 /tmp/usb

- Remount your UBI volume at /overlay to R/O

  mount -o remount,ro /overlay

- Write back the kernel and ubi partitions from USB drive

  cd /tmp/usb
  mtd write mtd4_kernel.bin /dev/<kernel_mtd>

  mtd write mtd8_ubi.bin /dev/<kernel_ubi>

- If everything went well, force a device reboot with
  reboot -f

Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota"
MTD partition which may be safely erased after reboot anyway.

Method 3: using built-in TFTP recovery (LAST RESORT):
- Assemble a recovery rootfs image from backup of stock partitions by
  concatenating "web", "kernel", "rootfs" images dumped from the device,
  as "root_uImage"
- Use it in place of "root_uImage" recovery initramfs image as in the
  TFTP pre-installation method.

Quirks and known issues
- Kernel partition size is increased to 4MB compared to stock 3MB, to
  accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
  image is at 2.5MB which is dangerously close to the limit. This has no
  effect on booting the system - but keep that in mind when reassembling
  an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
  you used before in stock firmware first. If you need to change it,
  please use protocok '3g' to establish connection once, or use the
  following command to change APN (and optionally IP type) manually:
  echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the green debug LED hidden
  inside the case. All other LEDs are controlled by modem, on which the
  router part has some influence only on Wi-Fi LED.
- Wi-Fi LED currently doesn't work while under OpenWrt, despite having
  correct GPIO mapping. All other LEDs are controlled by modem,
  including this one in stock firmware. GPIO19, mapped there only acts
  as a gate, while the actual signal source seems to be 5GHz Wi-Fi
  radio, however it seems it is not the LED exposed by ath10k as
  ath10k-phy0.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
  reset of whole board, not only the modem. It is attached to
  gpio-restart driver, to restart the modem on reboot as well, to ensure
  QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
  for OpenWrt operation at all - have fun lurking around.
- MAC address shift for 5GHz Wi-Fi used in stock firmware is
  0x320000000000, which is impossible to encode in the device tree, so I
  took the liberty of using MAC address increment of 1 for it, to ensure
  different BSSID for both Wi-Fi interfaces.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-02-05 12:14:08 +01:00
Lech Perczak
54e82f5c9a ath79: kernel: drop _machine_restart again
Backport patch ("MIPS: ath79: drop _machine_restart again"), which is
required to support GPIO restart handler on ZTE MF286, broken due to
_machine_restart being restored in kernel accidentally, wich causes any
registered restart handlers to not execute, including one from
ath79-reset driver.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-02-05 12:08:25 +01:00
John Audia
02fbdc6a47 bcm27xx: update distroconfig.txt for faster RPi4
Newer RPi 4 Rev 6 (8 GB models and recent 2 GB / 4 GB models) ship with
the so-called C0 processor which can run turbo mode at 1.8 GHz max rather
than 1.5 GHz gracefully.  Add 'arm_boost=1' to pi4 section of to enable.

Note that this setting has no effect on older chips; they continue with
their 1.5 GHz max unless users overclock them.

Ref: https://www.raspberrypi.com/news/bullseye-bonus-1-8ghz-raspberry-pi-4

Signed-off-by: John Audia <graysky@archlinux.us>
2022-02-05 00:44:35 +01:00
Julien Cassette
2c1f8a665e ipq40xx: add Linksys MR8300 WAN port
This makes the WAN interface and port appear in
LuCi -> Network -> Switch on Linksys MR8300.
This allows to configure a VLAN on WAN.

Fixes: FS#4227

Signed-off-by: Julien Cassette <julien.cassette@gmail.com>
2022-02-05 00:44:35 +01:00
Pawel Dembicki
a91ab8bc05 ipq40xx: add support for ZTE MF286D
ZTE MF286D is a LTE router with four gigabit ethernet ports
and integrated QMI mPCIE modem.

Hardware specification:

  - CPU: IPQ4019
  - RAM: 256MB
  - Flash: NAND 128MB + NOR 2MB
  - WLAN1:  Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
  - WLAN2:  Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2
  - LTE: mPCIe cat 12 card (Modem chipset MDM9250)
  - LAN: 4 Gigabit Ports
  - USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem)
  - Serial console: X8 connector 115200 8n1

Known issues:

  - Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs
    are driven by cpu.
  - Wifi LED is triggered by phy0tpt only
  - No VoIP support
  - LAN1/WAN port is configured as WAN
  - ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN
    and WLAN0/1

Opening the case:

1. Take of battery lid (no battery support for this model, battery cage
   is dummy).
2. Unscrew screw placed behind battery lid.
3. Take off back cover. It attached with multiple plastic clamps.
4. Unscrew four more screws hidden behind back case.
5. Remove front panel from blue chassis. There are more plastic
   clamps.
6. Unscrew two boards, which secures the PCB in the chassis.
7. Extract board from blue chassis.

Console connection (X8 connector):

1. Parameters: 115200 8N1
2. Pin description: (from closest pin to X8 descriptor to farthest)
    - VCC (3.3V)
    - TX
    - RX
    - GND

Install Instructions:

Serial + initramfs:
1. Place OpenWrt initramfs image for the device on a TFTP in
   the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to X8 connector.
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:
	setenv serverip 192.168.1.3
	setenv ipaddr 192.168.1.72
	set fdt_high 0x85000000
	tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
	bootm $loadaddr
5. Please make backup of original partitions, if you think about revert
   to stock.
6. Login via ssh or serial and remove stock partitions:
	ubiattach -m 9
	ubirmvol /dev/ubi0 -N ubi_rootfs
	ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. Install image via "sysupgrade -n".

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cosmetic changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-05 00:44:35 +01:00
Pawel Dembicki
4d3e17e205 generic: kernel: add patches with ZTE MF286D modem
This patch includes patches sent upstream with ZTE MF286D modem
support. It adds support for qmi and serial option driver.

Links to ML:
https://lore.kernel.org/linux-usb/20220111221132.14586-1-paweldembicki@gmail.com/
https://lore.kernel.org/linux-usb/20220111221205.14662-1-paweldembicki@gmail.com/

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-02-05 00:44:35 +01:00
Christian Lamparter
965e878333 ipq806x: G10: use ASROCK's wifi calibration data
brings back the ath10k QCA9980 wifi nodes to which
it adds ASROCK's wifi calibration data. These are
now provided by the ath10k_firmware.git's board-2.bin.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-05 00:44:35 +01:00
Christian Lamparter
20470580cd ipq806x: utilize nvmem-cells for pre-calibration data
converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.

The patch also moves previously existing referenced
nvmem-cells data nodes which were placed at the end
back into the partitions node. As well as removing
some duplicated properties from qcom-ipq8065-xr500.dts's
art (the included nighthawk.dtsi defines those already).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-05 00:41:36 +01:00
Christian Lamparter
a1693a8c2c apm821xx: WNDR4700: utilize ath9k nvmem-cells
the WNDR4700 can fetch its calibration data and
mac-addresses directly from the "wifi_data" partition.
This allows us to get rid of the 10-ath9k-eeprom file
for the apm821xx target completely.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-04 21:15:17 +01:00
Christian Lamparter
f095822699 apm821xx: convert legacy nand partition layout
in order to get nvmem-cells to work on AP and routers
(Netgears WNDR4700). The nvmem-cell needs to be within
a fixed-partition dt-node.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-04 21:15:17 +01:00
Christian Lamparter
1085c4b4a7 apm821xx: WNDR4700: delete dead dt definitions
cooling-{min|max}-level are no longer used.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-04 21:15:17 +01:00
Sven Eckelmann
7c3efd5273 ramips: Switch Teltonika RUT5xx to kernel GPIO-line watchdog driver
The commit 04e91631e0 ("om-watchdog: add support for Teltonika RUT5xx
(ramips)") used the deprecated om-watchdog daemon to handle the GPIO-line
connected watchdog on the Teltonika RUT5xx.

But this daemon has massive problems since commit 30f61a34b4
("base-files: always use staged sysupgrade"). The process will always be
stopped on sysupgrades. If the sysupgrade takes slightly longer, the
watchdog is not triggered at the correct time and thus the sysupgrade will
interrupted hard by the watchdog sysupgrade. And this hard interrupt can
easily brick the device when there is no fallback (dual-boot, ...).

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-02-03 22:27:15 +01:00
Hauke Mehrtens
dc2da6a233 bcm63xx: Remove patch already in Linux stable
Remove the 434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch, it was
already applied to Linux 5.10.37 and is not needed any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-02-01 23:34:07 +00:00
Rui Salvaterra
ff97fb98e3 kernel: bump 5.10 to 5.10.96
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-02-01 23:34:07 +00:00
Rui Salvaterra
b9736cb78c kernel: bump 5.10 to 5.10.95
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-02-01 23:34:07 +00:00
Rui Salvaterra
1343acc8cd kernel: bump 5.10 to 5.10.94
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0669-drm-vc4-hdmi-Make-sure-the-device-is-powered-with-CE.patch [1]
bcm27xx/patches-5.10/950-0672-drm-vc4-hdmi-Move-initial-register-read-after-pm_run.patch [1]
gemini/patches-5.10/0003-ARM-dts-gemini-NAS4220-B-fis-index-block-with-128-Ki.patch [2]

Manually rebased:
bcm27xx/patches-5.10/950-0675-drm-vc4-hdmi-Drop-devm-interrupt-handler-for-CEC-int.patch

Manually reverted:
generic/pending-5.10/860-Revert-ASoC-mediatek-Check-for-error-clk-pointer.patch [3]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.94&id=55b10b88ac8654fc2f31518aa349a2e643b37f18
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.94&id=958a8819d41420d7a74ed922a09cacc0ba3a4218
[3] https://lore.kernel.org/all/trinity-2a727d96-0335-4d03-8f30-e22a0e10112d-1643363480085@3c-app-gmx-bap33/

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-02-01 23:34:07 +00:00
Alar Aun
70eedac9b3 ipq40xx: add MikroTik cAP ac support
This adds support for the MikroTik RouterBOARD RBcAPGi-5acD2nD
(cAP ac), a  indoor dual band, dual-radio 802.11ac wireless AP, two
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/cap_ac for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 128 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
   · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
 - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 port,
   PoE in and passive PoE out

Unsupported:
 - PoE out

Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"

Signed-off-by: Alar Aun <alar.aun@gmail.com>
2022-02-01 23:18:58 +01:00
Stijn Tintel
cd6a6e3030 Revert "ramips: add support for ipTIME AX2004M"
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") seems to
leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no
longer boot. The leak is visible in u-boot:

   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  MIPS OpenWrt Linux-5.10.92
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x840000e4
     Data Size:    10750165 Bytes = 10.3 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x82000000
     Entry Point:  0x82000000

Normally, it should look like this:

   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  MIPS OpenWrt Linux-5.10.92
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0xbfca00e4
     Data Size:    2652547 Bytes = 2.5 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x80001000
     Entry Point:  0x80001000

Revert the commit to avoid more people soft-bricking their devices.

This reverts commit f4a79148f8.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-01 21:35:15 +02:00
Rafał Miłecki
da8b720b0e bcm4908: backport first 5.18 DTS changes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-02-01 11:35:07 +01:00
Sungbo Eo
ad5bf16001 ath79: convert remaining mtd-mac-address-increment
Commit d284e6ef0f ("treewide: convert mtd-mac-address-increment* to
generic implementation") renamed "mtd-mac-address-increment" property
to "mac-address-increment". Convert remaining usages that have been
added after that.

Fixes: af8a059bb4 ("ath79: add support for GL.iNet GL-XE300")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-01 14:55:40 +09:00
Sungbo Eo
f16f419022 ipq806x: convert remaining mtd-mac-address-increment
Commit d284e6ef0f ("treewide: convert mtd-mac-address-increment* to
generic implementation") renamed "mtd-mac-address-increment" property
to "mac-address-increment". Convert remaining usages that have been
added after that.

Fixes: f44e933458 ("ipq806x: provide WiFI mac-addresses from dts")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-01 14:55:40 +09:00
Sungbo Eo
c7a559980a ath79: improve support for Dongwon T&I DW02-412H
* Move &nand node to DTSI
* Utilize nvmem for fetching caldata
* Rename build recipe, clean before build
* Simplify KERNEL definition

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-01 14:54:16 +09:00
Daniel Golle
9ba7a83425
mediatek: mt7623: simplify partition generation
The two options 'emmc' and 'sdmmc' now became identical lines after
introducing CONFIG_TARGET_ROOTFS_PARTSIZE.
Remove the now useless if-clauses.

Fixes: a40b4d335a ("mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZE")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-31 15:02:36 +00:00
Daniel Golle
5e6867fd54
mediatek: u7623-02: enable early console also in legacy image
Append 'earlycon=uart8250,mmio32,0x11004000' to the boot arguments
embedded in device-tree in order to enable early console on the
UniElec U7623 board when using the vendor/stock bootloader.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-31 00:10:38 +00:00
Rafał Miłecki
840f07e532 bcm4908: backport bcm_sf2 patch for better LED registers support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-01-31 00:58:02 +01:00
Rafał Miłecki
a11e9fd1d5 bcm4908: fixup pinctrl patches for kernel 5.4
Fixes: b014589167 ("bcm4908: backport BCM4908 pinctrl driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-01-31 00:57:58 +01:00
Rafał Miłecki
b014589167 bcm4908: backport BCM4908 pinctrl driver
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-01-31 00:19:34 +01:00
Tamas Balogh
b21bc3479d ath79: ASUS RP-AC66 use flash till the end
This makes available the additional space,
which was occupied by OEM's jffs2 partition before:
"0x000000f80000-0x000001000000 : jffs2"

Reverting to the OEM firmware will also recover
this partition, i.e. it is not needed and can be
used by OpenWrt.

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-01-30 01:16:14 +09:00
Davide Fioravanti
8fde82095b ramips: add support for Wavlink WL-WN535K1
The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports
and one fast ethernet port. Mine is branded as Talius TAL-WMESH1.
It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3).
The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could
potentially work for WL-WN535G3R and WS-WN535G3R with little to none
effort, but it's untested.

Hardware
--------
SoC:   Mediatek MT7620A
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
  - 2x 10/100/1000 Mbps Ethernet (RTL8211F)
  - 1x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 internal antennas
BTN:
  - 1x Reset button
  - 1x Touchlink button (set to WPS)
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 3x Green leds (ethernet port status/act)
UART:
  - 57600-8-N-1

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on WN535K1_V1510_200916 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
	mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
		16384+0 records in
	16384+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
	rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done

6) After few seconds, in the textarea should appear this output:
		384+0 records in
	384+0 records out
	128+0 records in
	128+0 records out
	128+0 records in
	128+0 records out
	14720+0 records in
	14720+0 records out
	1024+0 records in
	1024+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro
	http://192.168.10.1/dev/mtd5ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update_mesh.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:E2 (factory @ 0x28)
   WAN		XX:XX:XX:XX:XX:E3 (factory @ 0x2e)
   WIFI 2G	XX:XX:XX:XX:XX:E4 (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:E5 (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:E5

2) The OEM firmware upgrade page accepts only files containing the
   string "WN535K1" in the filename.

3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid
(92780d80ab)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-30 01:15:23 +09:00
Sungbo Eo
f4a79148f8 ramips: add support for ipTIME AX2004M
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specification:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

MAC address:

| interface |        MAC        |     source     | comment
|-----------|-------------------|----------------|---------
|       LAN | 58:XX:XX:00:XX:9B |                | [1]
|       WAN | 58:XX:XX:00:XX:99 |                |
|   WLAN 2G | 58:XX:XX:00:XX:98 | factory 0x4    |
|   WLAN 5G | 5A:XX:XX:40:XX:98 |                |
|           |                   |                |
|           | 58:XX:XX:00:XX:98 | config ethaddr |

[1] Used in this patch as WLAN 5G MAC address with the local bit set

Load address:
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Installation via **recovery** mode:
1.  Press reset button, power up the device, wait >10s for CPU LED
    to stop blinking.
2.  Upload recovery image through the recovery web page at 192.168.0.1.

Revert to stock firmware:
1.  Install stock image via recovery mode.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
03aa57d7ab ramips: make the relocation address configurable
If no argument is given to relocate-kernel, KERNEL_LOADADDR will be used
just as before.

This is a preparation for ramips support of ipTIME AX2004M.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
6ff970bb51 mvebu: add support for ipTIME NAS1dual
ipTIME NAS1dual is a 1-bay NAS, based on Marvell Armada 385 SoC.

Specifications:
* SoC: 88F6820
* RAM: 2 GiB
* Flash: SPI NOR 64 MiB
* SATA: 1x 3Gb/s
* Ethernet: 2x 1GbE
* USB: 1x 3.0
* Fan: 2 speed level
* UART: J11 (115200 8N1)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
f4fd2a1354 mvebu: remove duplicate CONFIG_POWER_RESET entries
The option is already enabled in the target config since 9149ed4f05
("mvebu: cortexa9: Add support for Ctera C200-V2").

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
7a4a33060f kernel: add disabled POWER_RESET_QNAP
Move the disabled symbol from target configs to generic configs.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
957f9adeb1 kirkwood: add support for ipTIME NAS1
ipTIME NAS1 is a 1-bay NAS, based on Marvell Kirkwood SoC.

Specifications:
* SoC: 88F6281
* RAM: 256 MiB
* Flash: SPI NOR 16 MiB
* SATA: 1x 3Gb/s
* Ethernet: 1x 1GbE
* USB: 1x 2.0
* Fan: 2 speed level
* UART: JP1 (115200 8N1)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Notes:
* There are several variants of the model name: "NAS-I", "NASI", "NAS1".
  Here "NAS1" is adopted for consistent naming scheme.
* The reset button is also a USB copy button in stock FW,
  but in this patch the former is the only default behavior.

Installation via web interface:
1.  Flash sysupgrade image through the stock web interface.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
0c568d044f kirkwood: rework 02_network
Just like other targets do, introduce two setup functions for interfaces
and MAC addresses.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
aaebc7aa2e kirkwood: drop kernel 5.4 support
It has been 3 months since we switched this target to 5.10, now we can
remove the 5.4 files.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
81a561b4a6 kernel: move bootargs-append patch to generic
This moves bootargs-append support patch from ipq40xx and ipq806x to
generic. This way we can append additional boot arguments from DTS instead
of only being able to overwrite them.

This is a preparation for kirkwood support of ipTIME NAS1.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
John Audia
30cff7c3b0 kernel: bump 5.4 to 5.4.174
Removed upstreamed patches:
  layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.4.174&id=65816c1034769e714edb70f59a33bc5472d9e55f

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-28 22:06:03 +01:00
Hauke Mehrtens
d2ae4821c2 octeontx: Refresh kernel configuration
Refresh the kernel configuration.
No manual changes done.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-28 21:58:26 +01:00
Hauke Mehrtens
c120f7943e kernel: Add CONFIG_CRYPTO_DEV_OCTEONTX_CPT kernel config option
This new kernel configuration option is available when building the
octeontx target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-28 21:58:26 +01:00
Hauke Mehrtens
764b1ecb69 kernel: Fix compile warning
This fixes the following compile warning:
  CC      init/do_mounts.o
init/do_mounts.c:478:19: warning: 'mount_ubi_rootfs' defined but not used [-Wunused-function]
  478 | static int __init mount_ubi_rootfs(void)
      |                   ^~~~~~~~~~~~~~~~

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-28 21:58:26 +01:00
Hauke Mehrtens
fcb29171bc arc770: Remove arc770 target
The arc700 target is not booting up since some time, see here:
https://github.com/foss-for-synopsys-dwc-arc-processors/toolchain/issues/400

It looks like there is a problem in the toolchain when using glibc.

Currently no one is working on fixing this problem, remove the target
instead. This target also does not have many users we are aware of.

If someone wants to have this target back, feel free to add a fixed
version of this target again.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-28 21:58:24 +01:00
Stijn Tintel
a47f152943 ramips: enable I2C_CHARDEV in mt7621/config-5.10
I2C_CHARDEV used to be enabled in mt7621/config-5.4. Enable it in the
5.10 config, as it's required for PoE control on Unifi Switch Flex.

Fixes: b4aad29a1d ("ramips: add support for kernel 5.10")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-28 19:03:52 +02:00
Chuanhong Guo
c06482489d kernel: 5.10: drop broken-flash-reset patch
Flash accessing instruction templates are determined during probe since
v5.6 for spimem-dirmap support in spi-nor driver in upstream commit:
df5c21002cf4 ("mtd: spi-nor: use spi-mem dirmap API")
As a result, changing bus_width on the fly doesn't work anymore and this
patch will cause executing spi-mem ops with 3-byte address on 16-32M
flash area.
We can't easily revert that behavioral change upstream so drop the patch
to prevent u-boot and eeprom from being erased.

Fixes: b10d604459("kernel: add linux 5.10 support")
Reported-by: Frank Di Matteo <dimatto@foxmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-01-28 21:03:10 +08:00
David Bauer
2b583ab8a7 rockchip: disable UHS modes for NanoPi R4S
The NanoPi R4S leaves the SD card in 1.8V signalling when rebooting
while U-Boot requires the card to be in 3.3V mode.

Remove UHS support from the SD controller so the card remains in 3.3V
mode. This reduces transfer speeds but ensures a reboot whether from
userspace or following a kernel panic is always working.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-27 01:44:28 +01:00
Daniel Golle
f5865452ac
mediatek: mt7623: include regular AHCI PCI driver
The legacy image for the UniElec U7623-02 until now included
kmod-ata-ahci-mtk. The MT7623 chip doesn't have that IP and that
board uses a PCIe-connected AHCI controller for the SATA port and
mSATA-pins of the mPCIe socket. Hence include kmod-ata-ahci instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-25 00:38:28 +00:00
Robert Marko
b8ef54f5da ipq40xx: drop 5.4 kernel
Since 5.10 is now default, no point in keeping
5.4 around.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-01-24 12:07:42 +01:00
Daniel Golle
f5278bf820
mediatek: store random MAC address in U-Boot env on first boot
For devboards without a MAC address assigned from factory, store
the random MAC in U-Boot env on first boot to make it persistent.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 20:20:47 +00:00
Daniel Golle
31872a38be
uboot-envtools: add configuration for UniElec U7623 board
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 20:20:42 +00:00
Daniel Golle
1ee75dd290
mediatek: mt7623: rework images for U7623-02 board
Users of older OpenWrt versions need sysupgrade using the *emmc.img.gz
file once which will upgrade U-Boot and switch to the new image layout.
Users of the vendor firmware need to first flash the legacy image to
then sunsequently carry out a full-flash upgrade.

Alternatively the board can also be flashed using MediaTek's
proprietary SP Flash Tool.

Configuration as well as persistent MAC address will be lost once at
this point and you will have to redo (or restore) all configuration
manually. To restore the previous persistent MAC address users may set
it manually using

fw_setenv ethaddr 00:11:22:33:44:55

For future upgrades once running OpenWrt past this commit, the usual
*sysupgrade.itb file can be used.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 20:20:37 +00:00
Daniel Golle
4356e2b58a
mediatek: add common DTS aliases for UniElec U7623 board
* Use serial0 instead of serial2 for the only serial port
 * Add LED aliases
 * Add ethernet0 alias to inherit ethaddr from U-Boot env

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:36 +00:00
Daniel Golle
8a324fb759
uml: make use of 'rootfs-part' feature
Use 'rootfs-part' feature instead of referencing the TARGET_uml in
Config-images.in.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:31 +00:00
Daniel Golle
d05ac928f6
sunxi: make use of 'rootfs-part' feature
Use 'rootfs-part' feature instead of referencing the TARGET_sunxi in
Config-images.in.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:25 +00:00
Daniel Golle
3a69b4bbb9
omap: make use of 'rootfs-part' feature
Use 'rootfs-part' feature instead of referencing the TARGET_omap in
Config-images.in.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:20 +00:00
Daniel Golle
a40b4d335a
mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZE
Enable 'rootfs-part' feature to make the size of the partition of the
production image configurable instead of hard-coding it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:07 +00:00
Victorien Molle
af8a059bb4 ath79: add support for GL.iNet GL-XE300
The GL.iNet GL-XE300 is a 4G LTE Wireless router, based on QCA9531 SoC.

Specifications:

 - SoC: QCA9531 (650MHz)
 - RAM: DDR2 128M
 - Flash: SPI NOR 16M + SPI NAND 128M
 - WiFi: 2.4GHz with 2 antennas
 - Ethernet:
   - 1x LAN (10/100M)
   - 1x WAN (10/100M)
 - LTE:
 - USB: 1x USB 2.0 port
 - UART:
   - 3.3V, TX, RX, GND / 115200 8N1

MAC addresses as verified by OEM firmware:

 use    address   source
 LAN    *:c5      art 0x0 (label)
 WAN    *:c6      label + 1
 WLAN   *:c7      art 0x1002

Installation via U-Boot rescue:

1. Press and hold reset and power buttons simultaneously
2. Wait for the LAN led to blink 5 times
3. Release reset and power buttons
4. The rescue page is accessible via http://192.168.1.1
5. Select the OpenWrt factory image and start upgrade
6. Wait for the router to flash new firmware and reboot

Revert to stock firmware:

 i. Download the stock firmware from GL.Inet website
 ii. Use the same method explained above to flash the stock firmware

Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
[update commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-22 01:17:16 +01:00
Rodrigo Araujo
7c8ade1765 ramips: correct vendor name for COMFAST/Joowin
When Joowin WR758AC V1 and V2 devices were added, they should have been
added with the primary manufacturer name which is COMFAST, since Joowin
is just an alternate vendor name on some coutries or stores.

Fix this by changing the the vendor name on the respective files and set
Joowin as ALT0 variants while ensuring compatibility for early users.
Also adjust the model names to better follow the naming rules.

As a side effect, fix mt76x8 network script which was left incorrectly
unsorted on the case block conditions.

Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2")
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-22 01:17:04 +01:00
David Bauer
ef5f3eb700 ramips: read Tenbay T-MB5EU address from single location
Currently the WAN MAC address is read from a different offset contrary
to all other addresses.

There's conflicting information whether offset 0x28 on the factory
partition contains the valid WAN mac for all devices while 0x4 seems to
be uniform.

Read the WAN mac from this location and calculate it.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-22 01:16:56 +01:00
David Bauer
b0c04a37e4 ramips: update Tenbay T-MB5EU wireless MAC address
The current MAC address assignment is still incorrect.

Use the same MAC address as seen on the stock firmware
for both wireless interfaces.

The 5GHz MAC address OUI is +2 in the first EUI octet. We currently
don't do this in OpenWrt. Ignore this offset for now. With the current
assignment, recurring MAC addresses between radios is already taken care
of.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-22 01:16:49 +01:00
David Woodhouse
408b6558e4 ipq806x: Netgear D7800: Fix RAM and enable PCIe #2
This board has 512MiB of RAM like the R7800, and the VDSL modem is
attached to the second PCIe port.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2022-01-21 17:18:35 +00:00
Denis Kalashnikov
ec85e48a11 ath79: add support for reset key on MikroTik RB912UAG-2HPnD
On MikroTik RB91x board series a reset key shares SoC gpio
line #15 with NAND ALE and NAND IO7. So we need a custom
gpio driver to manage this non-trivial connection schema.
Also rb91x-nand needs to have an ability to disable a polling
of the key while it works with NAND.

While we've been integrating rb91x-key into a firmware, we've
figured out that:
* In the gpio-latch driver we need to add a "cansleep" suffix to
several gpiolib calls,
* When gpio-latch and rb91x-nand fail to get a gpio and an error
is -EPROBE_DEFER, they shouldn't report about this, since this
actually is not an error and occurs when the gpio-latch probe
function is called before the rb91x-key probe.
We fix these related things here too.

Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-19 16:40:12 +01:00
Paul Spooren
522e414dcb layerscape: switch to 5.10 Kernel
Tested by multiple users and since all targets need to be on Kernel 5.10
to be part of the next release, add changes.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-19 09:44:26 +01:00
Klaus Kudielka
431f379e9d mvebu: cortexa9: Fix board.d/01_leds
Fix syntax error in the case statement

Fixes: 9149ed4f05 ("mvebu: cortexa9: Add support for Ctera C200-V2")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
2022-01-18 20:13:14 +01:00
Sungbo Eo
266b5c83c3 ipq40xx: rename RT-AC42U WLAN/LAN LEDs
Assign LED numbers properly by adding function-enumerator property in DTS.

While at it, remove default trigger of LAN LEDs as it will be handled in
01_leds anyway.

Fixes: 51b9aef553 ("ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-17 20:38:43 +09:00
Sungbo Eo
e257405c1b ipq40xx: image: remove unused DTB_SIZE variable
It is not included in DEVICE_VARS anyways.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-17 20:38:43 +09:00
Alexey Smirnov
e23ca355b0 omap: add support for the TRNG Hardware Accelerator
According to TI docs (Processor SDK Linux Getting Started Guide)
the Random Number Generator hardware is found on
OMAP16xx, OMAP2/3/4/5, AM33xx/AM43xx boards. It already
defined in device tree files. Let's enable it.

Some tests:

root@RTS1_OI:~# rngtest -c 1000 </dev/hwrng
rngtest 6.10
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions.
There is NO warranty; not even for MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.

rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 999
rngtest: FIPS 140-2 failures: 1
rngtest: FIPS 140-2(2001-10-10) Monobit: 0
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 1
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=198.710; avg=1265.501; max=2976.417)Kibits/s
rngtest: FIPS tests speed: (min=1.780; avg=37.085; max=39.736)Mibits/s
rngtest: Program run time: 15961329 microseconds

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2022-01-16 21:42:19 +01:00
Daniel Kestrel
78057b5595 ltq-deu: add ltq-deu back to default packages
After enhancing ltq-deu, build it by default for the devices
using it.

Reverts: 964863b ("ltq-deu: Mark lantiq DEU broken")

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-16 21:42:19 +01:00
Lech Perczak
ebf639d282 ath79: use lzma-loader for ZyXEL NBG6716
Since gzip-compressed kernel image stopped fitting on 4MB kernel
partition on the device, use lzma-loader wrapping LZMA-compressed
kernel. This yields bootable device once again, and saves a very
substantial amount of space, the kernel size decreasing from about 4.4MB
to about 2.5MB for 5.10 kernel. This avoids changing of the flash layout
for the device.

While at that, reactivate the build for the device.

Fixes: 5d8ea6d34f ("ath79: Deactivate ZyXEL NBG6716 by default")
Cc: André Valentin <avalentin@marcant.net>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Alex Henrie <alexhenrie24@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-01-16 21:42:19 +01:00
Sven Eckelmann
8143709c90 ath79: Add support for OpenMesh OM2P v1
Device specifications:
======================

* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 18-24V passive POE (mode B)
    + used as WAN interface
  - eth1
    + builtin switch port 4
    + used as LAN interface
* 12-24V 1A DC
* external antenna

The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-16 21:42:19 +01:00
Sven Eckelmann
7f074fe1a7 ath79: Allow to set spi-nor mtd name via devicetree
On ar71xx, it was possible to overwrite the name of the spi-nor mtd device
identifier using the flash_platform_data which each mach-*.c could adjust
for its devices. A similar feature was introduced for mtd-physmap in
devicetree's. The property linux,mtd-name can be used to set the name and
provide a stable identifier for mtdpart from the bootloader.

But this feature is not yet available upstream for spi-nor devices which
also might receive their partition layout from the bootloader. But the
OpenWrt pistachio support for this property can simply be imported into
ath79 to gain this support.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-16 21:42:19 +01:00
Sven Eckelmann
1699c1dc7f ath79: Add support for OpenMesh OM5P-AC v2
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/200 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 4x GPIO-LEDs (3x wifi, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8031 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

This device support is based on the partially working stub from commit
53c474abbd ("ath79: add new OF only target for QCA MIPS silicon").

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-16 20:51:14 +01:00
Aleksander Jan Bajkowski
7e484b902d lantiq: backport latest upstream patches
This patch includes a series of performance improvements. All patches
were accepted and should land in 5.17.
NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):

	Down		Up
Before	539 Mbps	599 Mbps
After	624 Mbps	695 Mbps

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-01-16 20:51:14 +01:00
Thomas Nixon
255268ce1a lantiq: xrx200: enable use of baby jumbo frames
xrx200 max MTU is reduced so that it works correctly when set to the
max, and the max MTU of the switch is increased to match.

In 5.10, the switch driver now enables non-standard MTUs on a per-port
basis, with the overall frame size set based on the cpu port. When the
MTU is not used, this should have no effect. The maximum packet size is
limited as large packets cause the switch to lock up.

0702-net-lantiq-add-support-for-jumbo-frames.patch comes from net-next
commit 998ac358019e491217e752bc6dcbb3afb2a6fa3e.

In 5.4, all switch ports are configured to accept the max MTU, as 5.4
does not have port_max_mtu/port_change_mtu callbacks.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2022-01-16 20:51:14 +01:00
Rui Salvaterra
61e58f7cec kernel: bump 5.10 to 5.10.92
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-16 20:51:14 +01:00
Rui Salvaterra
7229981994 kernel: bump 5.10 to 5.10.91
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-16 20:51:14 +01:00
John Audia
a28afb9214 kernel: bump 5.4 to 5.4.172
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-16 16:23:45 +01:00
John Audia
53252c4ce9 kernel: bump 5.4 to 5.4.171
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-16 16:23:44 +01:00
Christian Lamparter
0a852d8a5e ipq40xx: AP-365: fix non-existent node or label "macaddr_mfginfo_1d"
Chen Minqiang reported on github:
|  DTC     arch/arm/boot/dts/qcom-ipq4029-ap-365.dtb
|qcom-ipq4019.dtsi:520.23-560.5: ERROR (phandle_references): /soc/wifi@a000000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
|  also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:243.8-248.3
|qcom-ipq4019.dtsi:562.23-602.5: ERROR (phandle_references): /soc/wifi@a800000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
|  also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:250.8-256.3
|ERROR: Input tree has errors, aborting (use -f to force output)
|scripts/Makefile.lib:326: recipe for target 'qcom-ipq4029-ap-365.dtb' failed

Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-16 13:14:58 +01:00
David Bauer
e821849c4f lantiq: increase fritz-cal-extract output limit
It was reported the caldata on the FritzBox 7430 is not only stored at
different offsets, but is also larger than the current output size
limit.

Increase the output file size limit (after deflate) by 1024 bytes.

Ref: FS#3604 ("ath9k firmware is 0 bytes on Fritzbox 7430")
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-15 23:05:55 +01:00
Christian Lamparter
144609bb3d build: move Build/copy-file to image-commands.mk
This is makro is present in more than one place.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 19:29:42 +01:00
Tamas Balogh
872b65ecc8 ath79: patch Asus RP-AC66 clean up and fix for sysupgrade image
- clean up leftovers regarding MAC configure in dts
- fix alphabetical order in caldata
- IMAGE_SIZE for sysupgrade image

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-01-15 17:41:19 +01:00
Marek Behún
83ce42b54e mvebu: Move cortexa9 specific config options from global config
Move config options
  CONFIG_PHY_MVEBU_A38X_COMPHY
  CONFIG_RTC_DRV_MV
to cortexa9/config-5.10.

These are not needed for arm64 targets.

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:41:19 +01:00
Pawel Dembicki
9149ed4f05 mvebu: cortexa9: Add support for Ctera C200-V2
2-Bay NAS - maximum two 3.5" Harddisks

Hardware:
  - SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC)
  - Ram: 1GB (2x Nanya NT5CC512M8DN-D1)
  - NAND Flash: 256MB (ESMT F59L2G81A-25T)
  - Lan: 1x GBE (Marvell 88E1318-NNB2)
  - Storage: 2x SATA HDD 3.5" Slot
  - USB: 2x USB 3.0 port (Renesas uPD720202)
  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
  - LEDs: 13x GPIO controlled
  - Buttons: 2x GPIO controlled

Known issues:
  - Buzzer is unused due lack of proper driver
  - USB1/2 usbport ledtrigger won't work (through DT)
  - Renesas uPD720202 requires firmware file. It's possible to find
    non-free binary. Please look for 'UPDATE.mem' file and put in into
    '/lib/firmware/renesas_usb_fw.mem' file.

Installation:
  - Apply factory initramfs image via stock web-gui.
  - Do sysupgrade to make installation complete.

Back to stock:
  - OpenWrt rootfs partition use unused space after stock firmware.
  - Full revert is possible.
  - Login via ssh and run:

 ## ctera_c200-v2_back_to_factory start ##
 . /lib/functions.sh
 part=$(find_mtd_part "active_bank")
 active_bank=$(strings "$part" | grep bank)
 if [ "$active_bank" = "bank1" ]; then
 	echo "bank2" > /tmp/change_bank
 else
 	echo "bank1" > /tmp/change_bank
 fi
 mtd write /tmp/change_bank active_bank
 reboot
 ## ctera_c200-v2_back_to_factory end ##

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(put back-to-stock script into commit message, removed dup. SUBPAGESIZE var,
added 01_leds for non-working dt-usb-port trigger)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:41:19 +01:00
Josef Schlehofer
01520a96e7 mvebu: enable watchdog for Armada 37XX
This option includes support for watchdog timer on Marvell Armada 37xx
SoCs. [1] It is useful e.g. for Turris MOX, Marvell ESPRESSObin

Enable armada-37xx-watchdog driver as built in for mvebu cortex-a53,
so that kernel can start serving as soon as the driver is probed, until userspace takes over it.

[1] https://cateee.net/lkddb/web-lkddb/ARMADA_37XX_WATCHDOG.html

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(improved commit message, 2nd paragraph)
Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:41:19 +01:00
Marek Behún
43659a7d74 mvebu: cortexa53: Enable Armada 37xx rWTM driver
Enabling Armada 37xx rWTM driver. This gives the kernel access to random
number generator, if provided by the rWTM firmware.

Note that the driver is called turris-mox-rwtm because it was initially
written for Turris MOX, but will also work on other Armada 37xx
platforms, if they use rWTM firmware from CZ.NIC [1].

It makes sense to have this driver built-in, so that kernel has access
to random number generator without needing to load any drivers.

[1] https://gitlab.nic.cz/turris/mox-boot-builder

Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andre Heider <a.heider@gmail.com>
2022-01-15 17:41:18 +01:00
Marek Behún
bf991fa357 kernel: 5.10: Backport pending Armada 3720 comphy patches
Backport 5 pending patches [1] for Armada 3720 comphy driver and one
patch for device tree, applied to mvebu-dt64, but pending to appear in
Linus' tree [2].

These patches makes the driver work correctly even with older, buggy
versions of TF-A firmware.

[1] http://lists.infradead.org/pipermail/linux-phy/2022-January/002598.html
[2] http://lists.infradead.org/pipermail/linux-phy/2021-December/002279.html

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:26:55 +01:00
Marek Behún
cf3a6e62a1 kernel: 5.10: Backport Armada 3720 comphy patches from 5.15
Backport 2 patches for Armada 3720 comphy from 5.15 kernel.

These are needed for clear application of pending patches that fix this
driver.

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:26:55 +01:00
Marek Behún
080691d7b1 kernel: 5.10: Backport pending pci-aardvark changes fixing MSI support
Backport Aardvark PCIe controller driver changes that fix MSI support,
that were recently sent to the linux-pci mailing list [1].

These changes fix MSI and MSI-X support for this PCIe controller, which,
among other things, make it possible to use NVMe drives with this PCIe
controllers.

[1] https://lore.kernel.org/linux-pci/20220110015018.26359-1-kabel@kernel.org/

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:26:55 +01:00
Marek Behún
612e1c6801 kernel: 5.10: Backport pci-aardvark driver changes from 5.17
Backport Aardvark PCIe controller driver changes that will appear in
5.17 kernel. They are currently accessible on LKML [1], in linux-next
repository [2], or in Bjorn Helgaas' repository [3].

These changes mainly enhance driver removal method.

[1] https://lore.kernel.org/linux-pci/20211130172913.9727-1-kabel@kernel.org/
[2] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/log/drivers/pci?h=next-20220107
[3] https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/log/?h=next

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:26:55 +01:00
Josef Schlehofer
9d530ac4bf mvebu: kernel: enable CONFIG_BLK_DEV_NVME
CONFIG_BLK_DEV_NVME [1]:
- This is a kernel driver for SSD connected to PCI or PCIe bus [1].
By default, it is enabled for targets "ipq807x", "rockchip/armv8"
and "x86/64".

With miniPCIe adapter, there is a possibility to connect NVMe disk
to Turris Omnia (cortex-a9), Turris MOX (cortex-a53).

It allows to boot system from NVMe disk, because of that it can not
be kmod package as you can not access the disk to be able to boot from
it.

CONFIG_NVME_CORE [2]:
- This is selected by CONFIG_BLK_DEV_NVME
It does not need to be explicitly enabled, but it is done for "ipq807",
"x64_64" and rockchip/armv8", which has also enabled the previous config
option as well.

Kernel increase: ~28k KiB on mamba kernel

Reference:
[1] https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[2] https://cateee.net/lkddb/web-lkddb/NVME_CORE.html

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-01-15 17:26:55 +01:00
Christian Lamparter
cfc13c4459 ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data
moves extraction entries out of 11-ath10k-caldata and into
the individual board's device-tree.

Some notes:
 - mmc could work as well (not tested)
 - devices that pass the partitions via mtdparts
   bootargs are kept as is
 - gl-b2200 has a weird pcie wifi device
   (vendor claims 9886 wave 2. But firmware-extraction
   was for a wave 1 device?!)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:26:55 +01:00
Christian Lamparter
10bc55c496 ipq40xx: add RT-ACRH13 alternative name to RT-AC58U
RT-ACRH13 is another name this device was sold as (US?).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:26:55 +01:00
Joshua Roys
51b9aef553 ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U
SOC:	IPQ4019
CPU:	Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
DRAM:	256 MB
NAND:	128 MiB Macronix MX30LF1G18AC
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN)
USB:	1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
WLAN2:	Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4
INPUT:	1x WPS, 1x Reset
LEDS:	Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN

This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed
with an intermediary initramfs image, the jffs2 ubi volume deleted, and
then finally a sysupgrade with the final image performed.

Signed-off-by: Joshua Roys <roysjosh@gmail.com>
(added ALT0)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:21:01 +01:00
Michael Pratt
74516f4357 ramips: fix reboot for remaining 32 MB boards
The following devices have a Winbond W25Q256FV flash chip,
which does not have the RESET pin enabled by default,
and otherwise would require setting a bit in a status register.

Before moving to Linux 5.4, we had the patch:
0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
which kept specific flash chips with explicit 3-byte and 4-byte address modes
to stay in 3-byte address mode while idle (after an erase or write)
by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch.

this was obsoleted by the patch:
481-mtd-spi-nor-rework-broken-flash-reset-support.patch
which uses the newer upstream flag SNOR_F_BROKEN_RESET
for devices with a flash chip that cannot be hardware reset with RESET pin
and therefore must be left in 3-byte address mode when idle.

The new patch requires that the DTS of affected devices
have the property "broken-flash-reset", which was not yet added for most of them.

This commit adds the property for remaining affected devices in ramips target,
specifically because of the flash chip model.

However, it is possible that there are other devices
where the flash chip uses an explicit 4-byte address mode
and the RESET pin is not connected to the SOC on the board,
and those DTS would also need this property.

Ref: 22d982ea00 ("ramips: add support for switching between 3-byte and 4-byte addressing")
Ref: dfa521f129 ("generic: spi-nor: rework broken-flash-reset")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-01-15 17:12:12 +01:00
Paul Spooren
daae59b729 at91: drop /etc/config/firewall
The file can't be part of base files or the base-files and firewall
packages collide. Two packages must not provide the same config files
without having a defined CONFLICT since it would result in an
undeterministic config state depending on what package is installed
last.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-15 16:36:28 +01:00
SeongUk Moon
9c8ccdcdc8 ramips: add support for ipTIME A6004NS-M
ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.

Specifications:
- SoC: MediaTek MT7621A (880MHz, Duel-Core)
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB (Winbond W25Q128BV)
- WiFi: MediaTek MT7615E (2.4GHz, 5GHz)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated)
- USB: USB 3.0 x1
- UART: [3.3V, TX, RX, GND] (57600 8N1)

Installation via web interface:
1. Flash initramfs image using OEM's Firmware Update page.
2. Connect to OpenWrt with an SSH connection to `192.168.1.1`.
3. Perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
1. Power on the device and connect the shell through UART.
2. Connect to the shell and press the `t` key on the keyboard.
3. Set fixed IP with  `192.168.0.2`  with subnet mask  `255.255.255.0`
4. Flash image via TFTP to  `192.168.0.1`

Additional Notes:
1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz.
2. If the 5Ghz frequency is too high, 5Ghz may not work.
3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi).

Signed-off-by: SeongUk Moon <antegral@antegral.net>
[convert CRLF to LF]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-15 20:43:14 +09:00
Kyoungkyu Park
6041c693dd ramips: add support for HUMAX E2
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
  - Switch: SoC internal
- UART: J2 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
   The device will be automatically rebooted.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
2022-01-15 20:05:46 +09:00
David Bauer
7f7705923a lantiq: add additional caldata offsets
It was reported the AVM FritzBox 7430 has different offsets for the
caldata depending on the device.

Whether this is due to custom bad-block handling or up to the installed
bootloader-version is unknown.

Try both known caldata offsets like it is already done for the ipq40xx
NAND based models. Use the same approach for the FritzBox 7412. While it
is currently unknown, whether it is affected, applying the same logic
has no downsides.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-15 11:27:53 +01:00
David Bauer
3154537864 lantiq: flag FritzBox 7360 family buttons active-low
All buttons of the FritzBox 7360 family are active-low, not active-high.
Corrent the GPIO flag. This fixes release triggers upon push of a button.

Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-14 22:12:53 +01:00
David Woodhouse
557067d9b1 mediatek: mt7623: Enable PCIe bus 0 (and thus SATA) on U7623
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2022-01-14 19:43:45 +00:00
Felix Fietkau
83b14ec026 ramips: enable badblock table support on linksys ea7xxx devices
Use remapping only on the kernel partitions.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
e2aa04d1e5 kernel: mtk_bmt: add support for the bbt format used on mt7621
This does not have spare blocks for remapping, and it is also not suitable
for random write access. It only skips over bad blocks on linear writes of an
image to a partition. As such, it is really only suitable for the kernel
partition, or other partitions with mostly static data

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
ff6b4f2cfb kernel: mtk_bmt: add abstraction for supporting other formats
Preparation for supporting remapping on MT7621

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
3c78fabb0d ramips: mt7621_nand: fix writing upper half of fdm data
Since the loop iterates from 0-3, subtracting 4 from the shift
multiplier does not make any sense

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
76b27f6bb9 mediatek: rework and fix mt7622-rfb1-ubi support
Limit bmt remapping range to cover everything up to and including the kernel image,
use the rest of the flash area for ubi.
Fix partition table and sysupgrade support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
7235c8d00c kernel: mtk_bmt: remap blocks after reaching bitflip threshold
This ensures that blocks are remapped before data becomes corrupt

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
0ddead0897 kernel: mtk_bmt: pass number of bitflips on read to the caller
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
b86452f841 kernel: mtk_bmt: add support for limiting range of remapping
This can be used to support ubi on top of mtk_bmt without reflashing the
boot loader. The boot loader + factory + kernel area is covered, while the
rest is passed through as-is

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
31b6cfb288 kernel: mtk_bmt: extend debug interface
Add support for showing remapped blocks and garbage collecting old
remapped blocks triggered by using the mark_good/mark_bad files

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
fde2421597 kernel: mtk_bmt: fix remapping after read/write failure
Copy from the previous block in order to preserve existing data

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
bcf91fe884 kernel: move mediatek BMT support patch to generic patches
Preparation for supporting BMT on MT7621. Move source files to the files/
subdirectory in order to simplify maintenance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Denis Kalashnikov
2d19e6c6a4 generic: platform/mikrotik: use MTD notifier
If the SPI probe is sufficiently delayed, the routerboot driver may fail
to init as the routerboot partitions are not yet available.

Register an MTD user notifier instead of doing straight init so that the
init subroutines are only executed when the target MTD partitions are
present.

Because the init/exit routines can now be called outside of the kernel
normal init/exit calls, they cannot be jettisoned and must always be
available: the __init and __exit qualifiers are thus removed.

Reported-by: Denis Kalashnikov <denis281089@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[bump hardconfig/softconfig versions]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
9571d9d4b1 ath79: qca955x: remove double declaration
No need to mention the same value twice

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
f11df68956 ath79: rb912: remove unused property
ar934x does not define property 'rgmii-enabled' in the parsing code
remove it

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
2a00054618 ath79: rb912: fix pll init issues
It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds.
Investigation shows that the board failed to adapt the ethernet pll values as shown here:

[    5.284359] ag71xx 19000000.eth: failed to read pll-handle property

added custom prints in code and triggering a link switch:

[   62.821446] Atheros AG71xx: fast reset
[   62.826442] Atheros AG71xx: update pll 2
[   62.830494] Atheros AG71xx: no pll regmap!

Comparison with another very similar board (rb922 - QCA955x) showed a missing
reference clock frequency in dts, which seems to cause a pll init issue.
Unfortunately, no errors are printed when this occurs.

Adding the frequency property fixes the pll init as it can be parsed now
by the ethernet driver.

[   55.861407] Atheros AG71xx: fast reset
[   55.866403] Atheros AG71xx: update pll 2
[   55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
fdda3130f2 mikrotik: make soft_config writable
Parent mtd partition needs to be writable

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
8441a622ec mikrotik: enable variable size erase
Add support for variable size erase blocks.
Enable it to all targets which has mikrotik targets.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
6eb196ed0f generic: platform/mikrotik: make soft_config writable without 4K sectors
Make soft_config writable in all cases. Performing soft_config commit
will fail if mtd partition is not writable.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[bump rb_softconfig version number]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
2bb7c1db70 imx: bump SDMA firmware to v3.6
No changelog available

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Daniel Golle
f2c3875dfc
generic: deny write to uImage.FIT sub-image partitions
Set policy bit to force read-only mode on uImage.FIT filesystem
sub-images mapped as block partitions by the FIT partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-11 00:06:16 +00:00
David Woodhouse
8cdc356f8c mediatek: mt7623: Re-enable ARM arch timer
CONFIG_ARM_ARCH_TIMER cannot be enabled in the config directly; it is only
selected by CONFIG_HAVE_ARM_ARCH_TIMER. We need to enable the latter in
our config.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 4f1c5b01c1 ("mediatek: mt7623: backport musb, improve HDMI console")
2022-01-10 13:45:41 +00:00
David Woodhouse
4648a60058 mediatek: mt7623: Disable power button reset for U7623-02 board
The Unielec U7623 doesn't have a physical power button; I think it's hard
wired so that it turns on automatically when power is applied (unlike the
Banana Pi R2 which is a pain).

So the 'reset on long press of power button' behaviour that we get when
we enable the PMIC keyboard driver is kind of unhelpful. Disable it.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 0d3f3323a2 ("mediatek: mt7623: enable more hardware features")
2022-01-10 13:45:41 +00:00
Sven Eckelmann
97f5617259 ath79: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-09 21:12:28 +01:00
Sven Eckelmann
72ef594550 ath79: Add support for OpenMesh OM5P-AN
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + 10/100 Mbps Ethernet
    + builtin switch port 1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-09 21:12:28 +01:00
Tamas Balogh
b29f4cf34c ath79: add support for ASUS RP-AC66
Asus RP-AC66 Repeater

Hardware specifications:
Board: AP152
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 25l128 16MB SPI-NOR
LAN/WAN: 1x1000M QCA8033
WiFi 5GHz: QCA9880
Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz

MAC addresses as verified by OEM firmware:
use            address   source
Lan/Wan   *:24         art 0x1002 (label)
2G             *:24         art 0x1002
5G             *:26         art 0x5006

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the factory image
    and press upload
 - Do not power off the device after OpenWrt has booted until the LED flashing.

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put factory.bin
 tftp> quit

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-01-09 20:32:41 +01:00
Fritz D. Ansel
693958497a mediatek mt7622: fix 300mhz typo in dts
The lowest frequency should be 300MHz, since that is the label
assigned to the OPP in the mt7622.dtsi device tree, while there is one
missing zero in the actual value.

To be clear, the lowest frequency should be 300MHz instead of 30MHz.

As mentioned @dangowrt on the OpenWrt forum there is no benefit in
leaving 30MHz as the lowest frequency.

Signed-off-by: Jip de Beer <gpk6x3591g0l@opayq.com>
Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
2022-01-09 14:48:16 +00:00
Stefan Lippers-Hollmann
abc2821286 x86: improve sysinfo handling of dummy values
Fall back to using board_vendor and board_name, if known dummy values
are used for sys_vendor and product_name.

Examples:
	To be filled by O.E.M.:To be filled by O.E.M.
-->	INTEL Corporation:ChiefRiver

	System manufacturer:System Product Name
-->	ASUSTeK COMPUTER INC.:P8H77-M PRO

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:Q1900DC-ITX

	Gigabyte Technology Co., Ltd.:To be filled by O.E.M.
-->	Gigabyte Technology Co., Ltd.:H77M-D3H

	empty:empty
-->	TYAN Computer Corporation:TYAN Toledo i3210W/i3200R S5211

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:H77 Pro4-M

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2022-01-08 23:25:05 +01:00
Alex Lewontin
62a2bfaff8 ipq806x: janitorial work, respect line lengths
This commit breaks up some lines so that they are shorter than
74 charcters.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Alex Lewontin
479acf03cc ipq806x: modularize generic subtarget
This commit moves the device profiles within the ipq806x/generic
subtarget into their own includable .mk file, to support eventually
having subtargets other than generic.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Aleksander Jan Bajkowski
46468fc9d5 lantiq: replace patches with version accepted upstream
Replace recently added patches with version accepted upstream.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-01-08 19:32:45 +01:00
Nick McKinney
e0a574d4b7 ramips: add support for Linksys EA6350 v4
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0

This is another MT7621 device, very similar to other Linksys EA7300
series devices.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Reverting to factory firmware:

Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking.  Hard-resetting this device three (3) times will
put the device in failsafe (default) mode.  At this point, flash the
OEM image to itself and reboot.  This puts the router back into the 'B'
image and allows for a firmware upgrade.

Troubleshooting:

If the firmware will not boot, first restore the factory as described
above.  This will then allow the factory.bin update to be applied
properly.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
2022-01-08 00:49:59 +01:00
Liangkuan Yang
bc7d36ba3a ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.

Specifications:

- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
  - Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
  - Switch: 1 * POWER switch

MAC addresses as verified by vendor firmware:

use   address             source
LAN   C8:XX:XX:3A:XX:E7   Config   "protest_lan_mac"  ascii  (label)
WAN   C8:XX:XX:3A:XX:EA   Config   "protest_wan_mac"  ascii
5G    C8:XX:XX:3A:XX:E8   Factory  "0x4"              hex
2.4G  CA:XX:XX:4A:XX:E8   [not on flash]

The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:

       5g                 2.4g         increment
 C8:XX:XX:90:XX:C3  CA:XX:XX:C0:XX:C3  0x30
 C8:XX:XX:3A:XX:08  CA:XX:XX:4A:XX:08  0x10
 C8:XX:XX:3A:XX:E8  CA:XX:XX:4A:XX:E8  0x10

Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.

Notes:

1. The vendor firmware allows you to connect to the router by telnet.
   (known version 1.0.0 can open telnet.)
   There is no official binary firmware available.
   Backup the important partitions data:
   "Bootloader", "Config", "Factory", and "firmware".
   Note that with the vendor firmware the memory is detected only 128MiB
   and the last 512KiB in NAND flash is not used.

2. The POWER LED is default on after press POWER switch.
   The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
   The WPS LED is controlled by MT7615DN's GPIO.
   Currently there is no proper way to configure it.

3. At the time of adding support the wireless config needs to be set up
   by editing the wireless config file:

 * Setting the country code is mandatory, otherwise the router loses
   connectivity at the next reboot. This is mandatory and can be done
   from luci. After setting the country code the router boots correctly.
   A reset with the reset button will fix the issue and the user has to
   reconfigure.

 * This is minor since the 5g interface does not come up online although
   it is not set as disabled. 2 options here:

   1- Either run the "wifi" command. Can be added from LuCI in system -
      startup - local startup and just add wifi above "exit 0".

   2- Or add the serialize option in the wireless config file as shown
      below. This one would work and bring both interfaces automatically
      at every boot:

      config wifi-device 'radio0'
          option serialize '1'

      config wifi-device 'radio1'
          option serialize '1'

Flash instructions using initramfs image:

1. Press POWER switch to power down if the router is running.

2. Connect PC to one of LAN ports, and set
   static IP address to "10.10.10.2", netmask to "255.255.255.0",
   and gateway to "10.10.10.1" manually on the PC.

3. Push and hold the WIFI button, and then power up the router.
   After about 10s (or you can call the recovery page, see "4" below)
   you can release the WIFI button.
   There is no clear indication when the router
   is entering or has entered into "RAISECOM Router Recovery Mode".

4. Call the recovery page for the router at "http://10.10.10.1".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   Click "Choose File" to select initramfs image, then click "Upload".

5. If image is uploaded successfully, you will see the page display
   "Device is upgrading the firmware... %".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   When the page display "Upgrade Successfully",
   you can set IP address as "automatically obtain".

6. After the rebooting (PC should automatically obtain an IP address),
   open the SSH connection, then download the sysupgrade image
   to the router and perform sysupgrade with it.

Flash back to vendor firmware:

 See "Flash instructions 1 - 5" above.
 The only difference is that in step 4
 you should select the vendor firmware which you backup.

Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2022-01-08 00:49:59 +01:00
Rodrigo Araujo
766733e172 ramips: add support for Joowin WR758AC V1 and V2
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.

Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).

OpenWrt developers forum page:
https://forum.openwrt.org/t/87355

Specifications:

 - CPU: MediaTek MT7628AN (580MHz)
 - Flash: 8MB
 - RAM: 64MB DDR2
 - 2.4 GHz: 802.11b/g/n (MT7603)
 - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
 - Antennas: 4x external single band antennas
 - LAN: 1x 10/100M
 - LED: Wifi 3x blue. Programmable
 - Button: WPS

MAC addresses as verified by OEM firmware:

use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004

How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image

Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-08 00:49:59 +01:00
Rui Salvaterra
536f051b97 kernel: bump 5.10 to 5.10.90
Add and enable a new kconfig knob to disable unprivileged eBPF by default.

Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-07 22:30:40 +01:00
John Audia
9f08557649 kernel: bump 5.4 to 5.4.170
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-07 22:30:40 +01:00