This introduces a common macro to assemble the correct url templates to
avoid code duplication and have the feed config handling in a central place.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45799
Turn on the auto recovery feature when flashing
and turn it off on successful bootup.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45792
With this patch the following two patches are backported:
* bridge: fix parsing of MLDv2 reports
* bridge: allow setting hash_max + multicast_router if interface is down
The former one is an important fix which got just applied to the net-tree
and is queued for stable. The latter is a patch which is needed to make
the hash_max and multicast_router attributes configurable through
netifd.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45783
Change the IB packaging to only embed libc, kernel and kmod packages by default
and generate repositories.conf to refer to the remote package repositories.
Introduce a new config option CONFIG_IB_STANDALONE which restores the old
behaviour of building self contained IB archives.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45772
Update kernel sources and refresh some patches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45761
Currently port 6 is shown as up 10MBit/half in LUCI and swconfig.
Reason is that all bits in the port 6 config are zero.
This means that also the aneg flag is not set and in this case
ar8216_read_port_link hardcodes the link to be up.
This is no real problem but a little annoying.
To fix this initialize port 6 with the aneg bit enabled.
This causes ar8216_read_port_link to evaluate the link status bit which is
always zero for port 6 as no PHY is connected to this port.
And it doesn't hurt as port 6 isn't connected to anything on TL-WDR4900.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45749
Fix an upstream regression on 3.18+ that causes rt305x based devices
to hang on boot.
Fixes#19715.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45747
Patches are cherry-picked from linux-next. We're also adding the
corresponding config option to the kernel.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45729
Patch cherry-picked from the following location:
https://chromium-review.googlesource.com/#/c/269931/
Disable the i2c device on gsbi4 and mark gsbi4_h and gsbi4_qup clks as
unused. If they are enabled, clock framework will turn them off at end
of probe. On ipq806x by design gsbi4_qup, gsbi4_h clks and i2c on gsbi4
are meant for RPM usage. So turning them off in kernel is incorrect.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45728
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
The diag.sh script lacked an entry for the status led on the RT-N14U,
map it to the asus:blue:power led which is also used by the boot loader
to report boot status (eg. TFTP recovery mode VS normal boot)
Signed-off-by: Matteo Panella <m.panella@level28.org>
SVN-Revision: 45725
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
SVN-Revision: 45724
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45722
There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in
ifxmips_pcie.c. Instead of defining a new hook we simply re-use the
existing ones (this is basically what the lantiq BSP code does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45718
The PCIe bus seems to require a hack/workaround when PCI is enabled as
well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is
only defined in lantiq's BSP code. The config symbol for the upstream
lantiq PCI driver is CONFIG_PCI_LANTIQ.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45717
There is also a OHCI controller, activate it for USB 1.1 support.
This should close#19601.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 45716
Add it to the appropriate places so the power led properly works
and ethernet is properly configured for failsafe.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45709
This patch adds support for the Huawei HG655b.
Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45708
Commit 5168c9a5702648eb690d32ec821647aca80aeba9 introduced a regression
during patch application on the 4.0 kernel. Some of the patched content
doesn't match the actual code, therefore leading to the following error:
Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch
patching file net/ipv6/ip6_output.c
Hunk #1 FAILED at 886.
1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c
patching file net/ipv6/route.c
Hunk #1 succeeded at 2247 (offset 2 lines).
Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f)
This change just adapts the actual patch to fix what is in kernel 4.0
and make it apply cleanly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45705
This device seems to have switch port 7 connected to the CPU:
vlan1ports=1 2 3 5 7*
vlan2ports=0 7u
it should be handled by eth1 and NVRAM seems to confirm that (no
et0macaddr entry, existing et1macaddr & et1phyaddr entries).
One of the remaining ports (4/8?) may be connected to the Quantenna SoC.
Original firmware boot log contains following messages:
(0x00,0x5d)Port 5 States Override: 0xfb
(0x00,0x5f)Port 7 States Override: 0xfb
(0x00,0x0e)Port 8 States Override: 0x0a
(why does it force port 5 state?!)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45692
It has 3 Ethernet interfaces, each of them connected to separated switch
port. Default NVRAM uses switch port 8 as CPU which is connected to the
3rd interface (eth2).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45681
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45676
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.
[ 2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.970000] 2 netgear-fw partitions found on MTD device firmware
[ 2.970000] 0x000000070000-0x000000188440 : "kernel"
[ 2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.990000] 0x000000188440-0x000000ff0000 : "rootfs"
The patch removes the rather useless warning message.
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45669
This change adds PCIe support to IPQ806x based platforms. The driver is
actually cherry-picked from the following LKML thread:
*https://lwn.net/Articles/643086/ (patches 110-111)
We also add here an additional fix to support multiple PCI controllers
on the same platform (patch 112), and to patch the ap148 & dbs149 DTS
files (patch 113).
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45663
This change enable zImage+appended dtb support in ipq806x kernel
options. The zImage will now be generated as part of the kernel
binaries. Platforms which do not have DT support enabled in U-boot
can now make use of it by generating zImage files and appending dtb
to it.
It is not used yet but it is done as a stepping stone for early IPQ806x
platforms, which did not include DT support in U-boot.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45662
ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended
on most ARM architectures. This automatically calculate ZRELADDR by
masking PHYS_OFFSET with 0xf8000000.
On IPQ806x though, the first ~20MB of RAM is reserved for the hardware.
In newer bootloader, when DT is used, this is not a problem, we just
reserve this memory in the device tree. But if the bootloader doesn't
have DT support, then ATAGS have to be used. In this case, the ARM
decompressor will position the kernel in this low mem, which will not be
in the RAM section mapped by the bootloader, which means the kernel will
freeze in the middle of the boot process trying to map the memory.
As a work around, this patch allows disabling AUTO_ZRELADDR when
ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders
which don't support device-tree, which is the case on certain early
IPQ806x based designs.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45661
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45658
There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties.
v2: set correct DEVICE_PROFILES for all images.
v2: migrate TP-LINK TL-WR710N v2 which was committed after v1.
v2: split very very long line `TARGET_DEVICES +=` into smaller parts
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 45643
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45635
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45634
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861
I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
2) must init GMAC0 before GMAC1
That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.
An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.
2) Possible consequence of no longer explicitly setting ethernet duplex/speed.
Review: With this patch, my ethernet and wireless works.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45633
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45630
This also changes the MAC address to one of the adresses actually used by the
stock firmware on one of the ethernet interfaces.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45599
INET_LRO deprecated and there are exactly two drivers using it, neither
being included in any of the targets enabling INET_LRO. At the same time
both drivers needing it select it.
So just disable it for everyone.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45584
This was a remnant of an old version.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45583
I still need to test following patch before backporting:
bgmac: leave interrupts disabled as long as there is work to do
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45571
Linux 4.0 was released on 2014-04-12
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45559
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45553
There are some rare devices without NAND, like Netgear EX6200 or
TP-LINK Archer C8.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45545
This is needed as prepare_generic_squashfs generates more data (in our
case 0x40004 B) and it's complex for sysupgrade to extract UBI image out
of TRX.
Signed-off-by: Dan Haab <dhaab@luxul.com>
SVN-Revision: 45541
DB149 is a IPQ8064 based platform. This patch adds the init scripts to
detect it, configure the network accordingly, and generate a flashable
image for it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45537
DB149 is an IPQ806x based development platform. This patch adds the dts
files to support it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45536
Certain IPQ806x based platforms are making use of this PHY. So we'll
enable it so it gets detected as such.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45535
-removed symbol because it should be handled by wpan.mk
-add missing FAKEHARD symbol (this symbol is removed in Kernel 4.0)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45530
